Skip to contentSkip to conversation

microsecond event scheduling in an application

DISCUSSION Junhee Lee 3 participants 4 messages Sep 8, 2009 – Sep 22, 2009

lore
Share & tools
lore

Junhee Lee

author
#0 lore raw

I am working on event scheduler which handles events in microsecond level. Actual this program is a network emulator using simulation codes. I'd like to expect that network emulator is working as simulation behaviors. Thus high resolution timer interrupt is required.
But high resolution timer interrupt derived by high tick frequency (jiffies clock) must effect the system performance.
Are there any comments or ways to support microsecond event scheduling without performance degradation?

Regards

#1 lore raw
Quoted 8 lines · Junhee Lee

I am working on event scheduler which handles events in microsecond level. Actual this program is a network emulator using simulation codes. I'd like to expect that network emulator is working as simulation behaviors. Thus high resolution timer interrupt is required.
But high resolution timer interrupt derived by high tick frequency (jiffies clock) must effect the system performance.
Are there any comments or ways to support microsecond event scheduling without performance degradation?

Just increasing HZ will degrade performance, yes, but we have hrtimers now which should be able to use granularities smaller than one jiffy, so it shouldn't be needed..

#2 lore raw
Quoted 10 lines · On Sun, 20 Sep 2009 12:26:09 -0600 Robert Hancock <[email protected]> wrote:
Quoted 8 lines · Junhee Lee

I am working on event scheduler which handles events in microsecond level. Actual this program is a network emulator using simulation codes. I'd like to expect that network emulator is working as simulation behaviors. Thus high resolution timer interrupt is required. But high resolution timer interrupt derived by high tick frequency (jiffies clock) must effect the system performance. Are there any comments or ways to support microsecond event scheduling without performance degradation?

Quoted 3 lines

Just increasing HZ will degrade performance, yes, but we have hrtimers now which should be able to use granularities smaller than one jiffy, so it shouldn't be needed..

select/poll use hrtimers, which are jiffies independent....

you'll be hard pressed to notice jiffies granularity in userspace nowadays..

Signature · 3 lines
Arjan van de Ven 	Intel Open Source Technology Centre
For development, discussion and tips for power savings, 
visit http://www.lesswatts.org
author
#3 lore raw

Thanks Arjan van de Ven.
Your comment is very useful to me.
Now I am trying to solve microsecond events scheduling using hrtimer.

-----Original Message-----
From: Arjan van de Ven [mailto:[email protected]]
Sent: Monday, September 21, 2009 3:31 AM
To: Robert Hancock
Cc: Junhee Lee; [email protected]
Subject: Re: microsecond event scheduling in an application

Quoted 10 lines · On Sun, 20 Sep 2009 12:26:09 -0600 Robert Hancock <[email protected]> wrote:
Quoted 8 lines · Junhee Lee

I am working on event scheduler which handles events in microsecond level. Actual this program is a network emulator using simulation codes. I'd like to expect that network emulator is working as simulation behaviors. Thus high resolution timer interrupt is required. But high resolution timer interrupt derived by high tick frequency (jiffies clock) must effect the system performance. Are there any comments or ways to support microsecond event scheduling without performance degradation?

Quoted 3 lines

Just increasing HZ will degrade performance, yes, but we have hrtimers now which should be able to use granularities smaller than one jiffy, so it shouldn't be needed..

select/poll use hrtimers, which are jiffies independent....

you'll be hard pressed to notice jiffies granularity in userspace nowadays..

Signature · 3 lines
Arjan van de Ven 	Intel Open Source Technology Centre
For development, discussion and tips for power savings, 
visit http://www.lesswatts.org