Skip to contentSkip to conversation

Using raidreconf to create raid0 from non-raid works, but df is wrong

DISCUSSION Mike Billings 3 participants 4 messages Jul 8, 2004 – Jul 9, 2004 MD RAID

lore
Share & tools
lore
#0 lore raw

Hi,

I originally had a 250G ide drive on my system. I added a second 250G and used raidreconf to go from non-raid to raid using "raidreconf -i /dev/hde1 -n /etc/raidtab -m /dev/md0". The conversion suceeded, mdadm reports that everything is ok, and the new raid0 works fine but df reports the wrong size. Is there any way to get df to report the correct size without wiping the data? Could I have done something with raidreconf differently to avoid this?

Thanks,
Mike

My setup info:

meatwad / # df -k
Filesystem 1K-blocks Used Available Use% Mounted on
/dev/md0 241263968 222247508 6760876 98% /mnt <<< that
should be ~500GB

meatwad / # cat /etc/raidtab
raiddev /dev/md0

raid-level                  0
nr-raid-disks               2
chunk-size                  32
persistent-superblock       1
nr-spare-disks              0

device /dev/hde1
raid-disk 0
device /dev/hdg1
raid-disk 1

meatwad / # mdadm --examine /dev/hde1
/dev/hde1:

          Magic : a92b4efc
        Version : 00.90.00
           UUID : 12511967:044c5448:e985eb8e:860b9a60

Creation Time : Wed Jul 7 10:50:53 2004
Raid Level : raid0
Device Size : 245111616 (233.76 GiB 250.99 GB)
Raid Devices : 2
Total Devices : 2
Preferred Minor : 0

Update Time : Thu Jul 8 03:50:30 2004
State : dirty, no-errors
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0
Checksum : bfcfe958 - correct
Events : 0.13

Chunk Size : 32K

Number Major Minor RaidDevice State
this 0 33 1 0 active sync
/dev/ide/host2/bus0/target0/lun0/part1
0 0 33 1 0 active sync
/dev/ide/host2/bus0/target0/lun0/part1
1 1 34 1 1 active sync
/dev/ide/host2/bus1/target0/lun0/part1

meatwad / # mdadm --examine /dev/hdg1
/dev/hdg1:

          Magic : a92b4efc
        Version : 00.90.00
           UUID : 12511967:044c5448:e985eb8e:860b9a60

Creation Time : Wed Jul 7 10:50:53 2004
Raid Level : raid0
Device Size : 245111616 (233.76 GiB 250.99 GB)
Raid Devices : 2
Total Devices : 2
Preferred Minor : 0

Update Time : Thu Jul 8 03:50:30 2004
State : dirty, no-errors
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0
Checksum : bfcfe95b - correct
Events : 0.13

Chunk Size : 32K

Number Major Minor RaidDevice State
this 1 34 1 1 active sync
/dev/ide/host2/bus1/target0/lun0/part1
0 0 33 1 0 active sync
/dev/ide/host2/bus0/target0/lun0/part1
1 1 34 1 1 active sync
/dev/ide/host2/bus1/target0/lun0/part1

meatwad / # mdadm -D /dev/md0
/dev/md0:

        Version : 00.90.00

Creation Time : Wed Jul 7 10:50:53 2004
Raid Level : raid0
Array Size : 490223232 (467.51 GiB 501.99 GB)
Raid Devices : 2
Total Devices : 2
Preferred Minor : 0
Persistence : Superblock is persistent

Update Time : Thu Jul 8 03:50:30 2004
State : dirty, no-errors
Active Devices : 2
Working Devices : 2
Failed Devices : 0
Spare Devices : 0

Chunk Size : 32K

Number Major Minor RaidDevice State
0 33 1 0 active sync
/dev/ide/host2/bus0/target0/lun0/part1
1 34 1 1 active sync
/dev/ide/host2/bus1/target0/lun0/part1

           UUID : 12511967:044c5448:e985eb8e:860b9a60
         Events : 0.13

dmesg output from starting the array:
md: bind<ide/host2/bus0/target0/lun0/part1,2>
md: ide/host2/bus0/target0/lun0/part1's event counter: 0000000c
md: ide/host2/bus1/target0/lun0/part1's event counter: 0000000c
md0: max total readahead window set to 496k
md0: 2 data-disks, max readahead per data-disk: 248k
raid0: looking at ide/host2/bus0/target0/lun0/part1
raid0: comparing ide/host2/bus0/target0/lun0/part1(245111616) with
ide/host2/bus0/target0/lun0/part1(245111616)

raid0:   END
raid0:   ==> UNIQUE
raid0: 1 zones
raid0: looking at ide/host2/bus1/target0/lun0/part1
raid0:   comparing ide/host2/bus1/target0/lun0/part1(245111616) with

ide/host2/bus0/target0/lun0/part1(245111616)
raid0: EQUAL
raid0: FINAL 1 zones
raid0: zone 0
raid0: checking ide/host2/bus0/target0/lun0/part1 ... contained as device 0
(245111616) is smallest!.
raid0: checking ide/host2/bus1/target0/lun0/part1 ... contained as device 1
raid0: zone->nb_dev: 2, size: 490223232
raid0: current zone offset: 245111616
raid0: done.
raid0 : md_size is 490223232 blocks.
raid0 : conf->smallest->size is 490223232 blocks.
raid0 : nb_zone is 1.
raid0 : Allocating 8 bytes for hash.
md: updating md0 RAID superblock on device
md: ide/host2/bus0/target0/lun0/part1 [events: 0000000d]<6>(write) ide/host2/bus0/target0/lun0/part1's sb offset: 245111616
md: ide/host2/bus1/target0/lun0/part1 [events: 0000000d]<6>(write) ide/host2/bus1/target0/lun0/part1's sb offset: 245111616

#1 lore raw
Quoted 9 lines · On Wednesday July 7, [email protected] wrote:

Hi,

I originally had a 250G ide drive on my system. I added a second 250G and used raidreconf to go from non-raid to raid using "raidreconf -i /dev/hde1 -n /etc/raidtab -m /dev/md0". The conversion suceeded, mdadm reports that everything is ok, and the new raid0 works fine but df reports the wrong size. Is there any way to get df to report the correct size without wiping the data? Could I have done something with raidreconf differently to avoid this?

If it is an ext2 or ext3, then resize2fs is what you need now. If some other filesystem.... maybe some other tool.

NeilBrown

#2 lore raw
Quoted 4 lines · On Wednesday July 7, [email protected] wrote:
Quoted 3 lines

Hi,

I originally had a 250G ide drive on my system. I added a second 250G

and

Quoted 3 lines
Quoted 3 lines

used raidreconf to go from non-raid to raid using "raidreconf -i /dev/hde1 -n /etc/raidtab -m /dev/md0". The conversion suceeded, mdadm reports that everything is ok, and the new raid0 works fine but df

reports

Quoted 9 lines
Quoted 3 lines

the wrong size. Is there any way to get df to report the correct size without wiping the data? Could I have done something with raidreconf differently to avoid this?

If it is an ext2 or ext3, then resize2fs is what you need now. If some other filesystem.... maybe some other tool.

NeilBrown

resize2fs did the trick! Thanks all!

Mike

#3 lore raw
In reply to Mike Billings

You must resize the partition now. The device that the partition on is now about 500Gb, but the partition is still 250Gb. If you're partition is ext2 or ext3, you can use resize2fs. A word of caution for you. I've used this utility many times, and it is necessary to do a e2fsck -f on the partition to be resized BOTH before and after. The program itself will require you to do it before. If you skip doing it after resize2fs completes, you will almost assuredly ruin your filesystem. I've skipped the fsck after the resize2fs myself 2-3 times, and it killed the filesystem every time.

TJ Harrell