UDP port 1194 marking/routing problem
Hi folks,
I have OpenVPN (respect for it developers) running on my FW.
Is has two external NICs and on internal everything is fine, except I want OpenVPN (UDP port 1194) going not via default route/network interface.
I use such commands:
iptables -t mangle -D POSTROUTING -o eth0 -p udp --dport 1194 -j MARK --set-mark 0x990 ip rule add fwmark 0x990 table openvpn1
ip route add default via $P2 dev eth0 table openvpn1
eth0 is FW's not default external NIC.
I have in use very similar iptables rules for my email server (TCP ports) and etc. Everything works fine.
What I'm doing wrong with marking/routing the UDP port?
Regards
Remus
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Hi Remus,
It seems that
iptables -t mangle -A POSTROUTING -o eth0 -p udp --dport 1194 -j MARK \
--set-mark 0x990will not take effect. (didn't you typo -A as -D?)
POSTROUTING is looked up after routing decision is made. Because the default route is dev eth1, the output device is eth1, -o eth0 will not match.
You should use
iptables -t mangle -A PREROUTING -p udp --destination <your openvpn \
peer> --dport 1194 -j MARK ....But I don't think you need to use MARK to do policy routing. It's a little overkill.
Why not simply route all traffic to your openvpn peer via device eth0?
Quoted 23 lines · Remus
Hi folks,
I have OpenVPN (respect for it developers) running on my FW.
Is has two external NICs and on internal everything is fine, except I want OpenVPN (UDP port 1194) going not via default route/network interface.I use such commands:
iptables -t mangle -D POSTROUTING -o eth0 -p udp --dport 1194 -j MARK --set-mark
0x990ip rule add fwmark0x990table openvpn1
ip route add default via $P2 dev eth0 table openvpn1eth0 is FW's not default external NIC.
I have in use very similar iptables rules for my email server (TCP ports) and etc. Everything works fine.
What I'm doing wrong with marking/routing the UDP port?Regards
Remus
Signature · 6 lines
lark _______________________________________________ LARTC mailing list [email protected] http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Wang,
That solution does not suite me:
Quoted 2 lines
ip route add default via $DEFAULTGW dev eth1 ip route add xxx.xxx.xxx.xxx/32 via $ANOTHERGW dev eth0
Because only UPD 1194 has to be routed via eth0 to OpenVPN server IP, everything else
to same Ip has to go via eth1.
Any ideas?
Regards
Remus
----- Original Message -----
From: "Wang Jian" <[email protected]>
To: "Remus" <[email protected]>
Cc: <[email protected]>; <[email protected]>
Sent: Wednesday, April 06, 2005 1:38 PM
Subject: Re: [Openvpn-users] Re: [LARTC] UDP port 1194 marking/routing problem
Quoted 127 lines
Hi Remus,
I means: don't use policy routing, because you can use much simpler solution.
Example:
ip route add default via $DEFAULTGW dev eth1 ip route add xxx.xxx.xxx.xxx/32 via $ANOTHERGW dev eth0
The second, send all your traffic to IP xxx.xxx.xxx.xxx via eth0. When your box acts as your intranet's gateway, you can SNAT or MASQUERADE on eth0, like
iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE.
For you openvpn configuration, you can either bind openvpn to eth0's ip, or let system chooose the IP, in most case the output interface.
Quoted 104 lines · Remus
Hi Wang,
We specialy got two Internet connections, one is only for the OpenVPN (it is
heavily used) and second for everthing else.
I will give a try to PREROUTING stuff right away.What do mean : But I don't think you need to use MARK to do policy routing.
It's a little overkill.Do you another suggestion than iptables/MARK?
Regards
Remus
----- Original Message -----
From: "Wang Jian" <[email protected]>
To: <[email protected]>
Cc: "Remus" <[email protected]>; <[email protected]>
Sent: Wednesday, April 06, 2005 12:23 PM
Subject: [Openvpn-users] Re: [LARTC] UDP port 1194 marking/routing problemQuoted 74 lines
Hi Remus,
It seems that
iptables -t mangle -A POSTROUTING -o eth0 -p udp --dport 1194 -j MARK \ --set-mark 0x990will not take effect. (didn't you typo -A as -D?)
POSTROUTING is looked up after routing decision is made. Because the default route is dev eth1, the output device is eth1, -o eth0 will not match.
You should use
iptables -t mangle -A PREROUTING -p udp --destination <your openvpn \ peer> --dport 1194 -j MARK ....But I don't think you need to use MARK to do policy routing. It's a little overkill.
Why not simply route all traffic to your openvpn peer via device eth0?
Quoted 27 lines · Remus
Hi folks,
I have OpenVPN (respect for it developers) running on my FW. Is has two external NICs and on internal everything is fine, except I want OpenVPN (UDP port 1194) going not via default route/network interface.
I use such commands:
iptables -t mangle -D POSTROUTING -o eth0 -p udp --dport 1194 -j MARK --set-mark
0x990
ip rule add fwmark0x990table openvpn1
ip route add default via $P2 dev eth0 table openvpn1eth0 is FW's not default external NIC.
I have in use very similar iptables rules for my email server (TCP ports)
and etc.
Everything works fine.
What I'm doing wrong with marking/routing the UDP port?Regards
Remus
Signature · 14 lines
lark ------------------------------------------------------- SF email is sponsored by - The IT Product Guide Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now. http://ads.osdn.com/?ad_ide95&alloc_id396&op=click _______________________________________________ Openvpn-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/openvpn-users
Quoted 23 lines
Quoted 4 lines
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartcSignature · 13 lines
lark ------------------------------------------------------- SF email is sponsored by - The IT Product Guide Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now. http://ads.osdn.com/?ad_ide95&alloc_id396&op=click _______________________________________________ Openvpn-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/openvpn-users
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Hi Remus,
Quoted 8 lines · Remus
Wang,
That solution does not suite me:
Quoted 2 lines
ip route add default via $DEFAULTGW dev eth1 ip route add xxx.xxx.xxx.xxx/32 via $ANOTHERGW dev eth0
Because only UPD 1194 has to be routed via eth0 to OpenVPN server IP, everything else
to same Ip has to go via eth1.
I see. So you need policy routing. Change your netfilter rule from POSTROUTING to POSTROUTING.
Quoted 162 lines
----- Original Message -----
From: "Wang Jian" <[email protected]>
To: "Remus" <[email protected]>
Cc: <[email protected]>; <[email protected]>
Sent: Wednesday, April 06, 2005 1:38 PM
Subject: Re: [Openvpn-users] Re: [LARTC] UDP port 1194 marking/routing problemQuoted 150 lines
Hi Remus,
I means: don't use policy routing, because you can use much simpler solution.
Example:
ip route add default via $DEFAULTGW dev eth1 ip route add xxx.xxx.xxx.xxx/32 via $ANOTHERGW dev eth0
The second, send all your traffic to IP xxx.xxx.xxx.xxx via eth0. When your box acts as your intranet's gateway, you can SNAT or MASQUERADE on eth0, like
iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE.
For you openvpn configuration, you can either bind openvpn to eth0's ip, or let system chooose the IP, in most case the output interface.
Quoted 108 lines · Remus
Hi Wang,
We specialy got two Internet connections, one is only for the OpenVPN (it is
heavily used) and second for everthing else.
I will give a try to PREROUTING stuff right away.What do mean : But I don't think you need to use MARK to do policy routing.
It's a little overkill.Do you another suggestion than iptables/MARK?
Regards
Remus
----- Original Message -----
From: "Wang Jian" <[email protected]>
To: <[email protected]>
Cc: "Remus" <[email protected]>; <[email protected]>
Sent: Wednesday, April 06, 2005 12:23 PM
Subject: [Openvpn-users] Re: [LARTC] UDP port 1194 marking/routing problemQuoted 50 lines
Hi Remus,
It seems that
iptables -t mangle -A POSTROUTING -o eth0 -p udp --dport 1194 -j MARK \ --set-mark 0x990will not take effect. (didn't you typo -A as -D?)
POSTROUTING is looked up after routing decision is made. Because the default route is dev eth1, the output device is eth1, -o eth0 will not match.
You should use
iptables -t mangle -A PREROUTING -p udp --destination <your openvpn \ peer> --dport 1194 -j MARK ....But I don't think you need to use MARK to do policy routing. It's a little overkill.
Why not simply route all traffic to your openvpn peer via device eth0?
Quoted 23 lines · Remus
Hi folks,
I have OpenVPN (respect for it developers) running on my FW. Is has two external NICs and on internal everything is fine, except I want OpenVPN (UDP port 1194) going not via default route/network interface.
I use such commands:
iptables -t mangle -D POSTROUTING -o eth0 -p udp --dport 1194 -j MARK --set-mark
0x990
ip rule add fwmark0x990table openvpn1
ip route add default via $P2 dev eth0 table openvpn1eth0 is FW's not default external NIC.
I have in use very similar iptables rules for my email server (TCP ports)
and etc.
Everything works fine.
What I'm doing wrong with marking/routing the UDP port?Quoted 24 lines
Quoted 4 lines
Regards
Remus
Signature · 14 lines
lark ------------------------------------------------------- SF email is sponsored by - The IT Product Guide Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now. http://ads.osdn.com/?ad_ide95&alloc_id396&op=click _______________________________________________ Openvpn-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/openvpn-users_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartcSignature · 13 lines
lark ------------------------------------------------------- SF email is sponsored by - The IT Product Guide Read honest & candid reviews on hundreds of IT Products from real users. Discover which products truly live up to the hype. Start reading now. http://ads.osdn.com/?ad_ide95&alloc_id396&op=click _______________________________________________ Openvpn-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/openvpn-users
Signature · 6 lines
lark _______________________________________________ LARTC mailing list [email protected] http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc