Skip to contentSkip to conversation

netgear ga621 / ns83820

DISCUSSION Rob Myers 3 participants 4 messages Nov 27, 2001

lore
Share & tools
lore

Rob Myers

author
#0 lore raw

hello

im having trouble with a netgear ga621, which is a fiber gigabit card that uses the ns83820 chipset [1]. currently i am using kernel 2.4.9+XFS and the netgear provided driver. i would like to switch to 2.4.16, but the netgear driver does not compile. i presume the problems with that driver are due to the mm changes in 2.4.10.[2] while the ns83820 driver seems to load properly the card does not seem to be able to communicate with the switch [3]. tcpdump does not show any traffic being recieved by the card.

am i wrong in thinking that the ns83820 driver in 2.4.16 should support this card?

has anyone else had any success making this card work with the netgear driver since 2.4.10?

thanks and any help/education appreciated

rob.

[1] output of lspci:
01:0a.0 Ethernet controller: National Semiconductor Corporation: Unknown device 0022
Subsystem: Netgear: Unknown device 621a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at cc00 [size=256]
Region 1: Memory at feb00000 (32-bit, non-prefetchable)
[size=4K]
Expansion ROM at fe800000 [disabled] [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

[2] netgear driver compilation errors:
kgcc -D__KERNEL__ -D__SMP__ -DMODULE -DCLONE -D__NO_VERSION__ -D_DUMP -DSINGLE_PACKET -D_GA621_ -DINTR_HOLDOFF -DMEMMAPPED_IO -D_DBG -DPHY_INTR -DFAILURE_MESSAGES -DSTATISTICS -DASSERTION -DCHECKSUM -DERRDEBUG -O -Wall -I/usr/src/linux/include -g -w sp.c /usr/src/linux/include/asm/pgalloc.h: In function `get_pgd_fast':
In file included from /usr/src/linux/include/linux/highmem.h:5,

                 from /usr/src/linux/include/linux/skbuff.h:27,
                 from /usr/src/linux/include/linux/netdevice.h:146,
                 from nsmtypes.h:22,
                 from sp.c:18:

/usr/src/linux/include/asm/pgalloc.h:68: `cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function) /usr/src/linux/include/asm/pgalloc.h:68: (Each undeclared identifier is reported only once
/usr/src/linux/include/asm/pgalloc.h:68: for each function it appears in.)
/usr/src/linux/include/asm/pgalloc.h: In function `free_pgd_fast':
/usr/src/linux/include/asm/pgalloc.h:79: cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function) /usr/src/linux/include/asm/pgalloc.h: In function pte_alloc_one_fast':
/usr/src/linux/include/asm/pgalloc.h:111: cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function) /usr/src/linux/include/asm/pgalloc.h: In function pte_free_fast':
/usr/src/linux/include/asm/pgalloc.h:121: `cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function)

[3]ns83820.c: National Semiconductor DP83820 10/100/1000 driver. eth%d: enabling 64 bit PCI.
eth1: ns83820.c v0.13: DP83820 00:40:f4:29:e9:ef pciaddr=0xfeb00000 irq=21 rev 0x103
eth1: link now 1000(?) mbps, full duplex and up.

#1 lore raw

Sure, I have it up using the netgear driver version 1.02 on 2.4.16. I didn't have any problems with compiling the driver against 2.4.16 with the same options that you list. Previous to this it was working fine on 2.4.11-pre6. The only obvious difference I can see is that you are using modversions and I am not.

--
Jason Holmes

Quoted 79 lines · Rob Myers

hello

im having trouble with a netgear ga621, which is a fiber gigabit card that uses the ns83820 chipset [1]. currently i am using kernel 2.4.9+XFS and the netgear provided driver. i would like to switch to 2.4.16, but the netgear driver does not compile. i presume the problems with that driver are due to the mm changes in 2.4.10.[2] while the ns83820 driver seems to load properly the card does not seem to be able to communicate with the switch [3]. tcpdump does not show any traffic being recieved by the card.

am i wrong in thinking that the ns83820 driver in 2.4.16 should support this card?

has anyone else had any success making this card work with the netgear driver since 2.4.10?

thanks and any help/education appreciated

rob.

[1] output of lspci:
01:0a.0 Ethernet controller: National Semiconductor Corporation: Unknown device 0022
Subsystem: Netgear: Unknown device 621a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at cc00 [size=256]
Region 1: Memory at feb00000 (32-bit, non-prefetchable)
[size=4K]
Expansion ROM at fe800000 [disabled] [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

[2] netgear driver compilation errors:
kgcc -D__KERNEL__ -D__SMP__ -DMODULE -DCLONE -D__NO_VERSION__ -D_DUMP

(quoted diff) +0 -3
-DSINGLE_PACKET -D_GA621_ -DINTR_HOLDOFF -DMEMMAPPED_IO -D_DBG
-DPHY_INTR -DFAILURE_MESSAGES -DSTATISTICS -DASSERTION -DCHECKSUM
-DERRDEBUG -O -Wall -I/usr/src/linux/include -g -w  sp.c

/usr/src/linux/include/asm/pgalloc.h: In function `get_pgd_fast':
In file included from /usr/src/linux/include/linux/highmem.h:5,

                 from /usr/src/linux/include/linux/skbuff.h:27,
                 from /usr/src/linux/include/linux/netdevice.h:146,
                 from nsmtypes.h:22,
                 from sp.c:18:

/usr/src/linux/include/asm/pgalloc.h:68: `cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function) /usr/src/linux/include/asm/pgalloc.h:68: (Each undeclared identifier is reported only once
/usr/src/linux/include/asm/pgalloc.h:68: for each function it appears in.)
/usr/src/linux/include/asm/pgalloc.h: In function `free_pgd_fast':
/usr/src/linux/include/asm/pgalloc.h:79: cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function) /usr/src/linux/include/asm/pgalloc.h: In function pte_alloc_one_fast':
/usr/src/linux/include/asm/pgalloc.h:111: cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function) /usr/src/linux/include/asm/pgalloc.h: In function pte_free_fast':
/usr/src/linux/include/asm/pgalloc.h:121: `cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function)

[3]ns83820.c: National Semiconductor DP83820 10/100/1000 driver. eth%d: enabling 64 bit PCI.
eth1: ns83820.c v0.13: DP83820 00:40:f4:29:e9:ef pciaddr=0xfeb00000 irq=21 rev 0x103
eth1: link now 1000(?) mbps, full duplex and up.

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

#3 lore raw
In reply to Rob Myers
Quoted 5 lines · Rob Myers

am i wrong in thinking that the ns83820 driver in 2.4.16 should support this card?

has anyone else had any success making this card work with the netgear driver since 2.4.10?

No, fibre is not supported as I've not encountered any test hardware yet. It shouldn't be much work to get it going, though.

-ben

author
#2 lore raw
In reply to Jason Holmes

jason-

thanks for your speedy and helpful response. the card is now working with 2.4.16-xfs and the netgear driver. to be honest i dont know why, i simply blew away /usr/src/linux and started over.

thanks again

rob.

Quoted 89 lines · Jason Holmes

Sure, I have it up using the netgear driver version 1.02 on 2.4.16. I didn't have any problems with compiling the driver against 2.4.16 with the same options that you list. Previous to this it was working fine on 2.4.11-pre6. The only obvious difference I can see is that you are using modversions and I am not.

--
Jason Holmes

Quoted 79 lines · Rob Myers

hello

im having trouble with a netgear ga621, which is a fiber gigabit card that uses the ns83820 chipset [1]. currently i am using kernel 2.4.9+XFS and the netgear provided driver. i would like to switch to 2.4.16, but the netgear driver does not compile. i presume the problems with that driver are due to the mm changes in 2.4.10.[2] while the ns83820 driver seems to load properly the card does not seem to be able to communicate with the switch [3]. tcpdump does not show any traffic being recieved by the card.

am i wrong in thinking that the ns83820 driver in 2.4.16 should support this card?

has anyone else had any success making this card work with the netgear driver since 2.4.10?

thanks and any help/education appreciated

rob.

[1] output of lspci:
01:0a.0 Ethernet controller: National Semiconductor Corporation: Unknown device 0022
Subsystem: Netgear: Unknown device 621a
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin A routed to IRQ 21
Region 0: I/O ports at cc00 [size=256]
Region 1: Memory at feb00000 (32-bit, non-prefetchable)
[size=4K]
Expansion ROM at fe800000 [disabled] [size=64K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

[2] netgear driver compilation errors:
kgcc -D__KERNEL__ -D__SMP__ -DMODULE -DCLONE -D__NO_VERSION__ -D_DUMP

(quoted diff) +0 -3
-DSINGLE_PACKET -D_GA621_ -DINTR_HOLDOFF -DMEMMAPPED_IO -D_DBG
-DPHY_INTR -DFAILURE_MESSAGES -DSTATISTICS -DASSERTION -DCHECKSUM
-DERRDEBUG -O -Wall -I/usr/src/linux/include -g -w  sp.c

/usr/src/linux/include/asm/pgalloc.h: In function `get_pgd_fast':
In file included from /usr/src/linux/include/linux/highmem.h:5,

                 from /usr/src/linux/include/linux/skbuff.h:27,
                 from /usr/src/linux/include/linux/netdevice.h:146,
                 from nsmtypes.h:22,
                 from sp.c:18:

/usr/src/linux/include/asm/pgalloc.h:68: `cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function) /usr/src/linux/include/asm/pgalloc.h:68: (Each undeclared identifier is reported only once
/usr/src/linux/include/asm/pgalloc.h:68: for each function it appears in.)
/usr/src/linux/include/asm/pgalloc.h: In function `free_pgd_fast':
/usr/src/linux/include/asm/pgalloc.h:79: cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function) /usr/src/linux/include/asm/pgalloc.h: In function pte_alloc_one_fast':
/usr/src/linux/include/asm/pgalloc.h:111: cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function) /usr/src/linux/include/asm/pgalloc.h: In function pte_free_fast':
/usr/src/linux/include/asm/pgalloc.h:121: `cpu_data_Rsmp_d3b73c3c' undeclared (first use in this function)

[3]ns83820.c: National Semiconductor DP83820 10/100/1000 driver. eth%d: enabling 64 bit PCI.
eth1: ns83820.c v0.13: DP83820 00:40:f4:29:e9:ef pciaddr=0xfeb00000 irq=21 rev 0x103
eth1: link now 1000(?) mbps, full duplex and up.

-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/