Questions?
I have some general questions for all:
How many of you are involved with embedded linux development using a MIPS processor?
What endianess have you chosen for your project and why?
If you have not guessed it, I am involved with a MIPS/Linux embedded project and we are trying to determine if there are any pros or cons in one endianess over the other.
Signature · 8 lines
/************************* Marc Karasek Sr. Firmware Engineer iVivity Inc. [email protected] 678.990.1550 x238 678.990.1551 Fax *************************/
It also depends on which new drivers you expect to use and thus need to port from the x86 world. I can certainly tell you that we always start off with LE for driver porting, for obvious reasons (x86, PCI), and then go BE after that.
/Hartvig
Quoted 36 lines · Marc Karasek
No, I have been involved with too many sorties in the war already. I was just asking if there was any issues with one side or the other from a purely technical aspect.
Quoted 21 lines · Steven J. Hill
Quoted 4 lines · Marc Karasek
How many of you are involved with embedded linux development using a MIPS processor?
A fair number of us. Over a hundred easily.
Quoted 2 lines
What endianess have you chosen for your project and why?
You don't really want to start this holy war, do you? That aside, usually big endian is more useful in applications moving networking type traffic or a fair amount of graphics processing. Little endian is handy if you are porting applications from Windows or a lot of your software is written in little endian.
That's my $.02.
-Steve
Signature · 1 line
Steven J. Hill - Embedded SW EngineerSignature · 8 lines
/************************* Marc Karasek Sr. Firmware Engineer iVivity Inc. [email protected] 678.990.1550 x238 678.990.1551 Fax *************************/
Quoted 4 lines · Marc Karasek
How many of you are involved with embedded linux development using a MIPS processor?
A fair number of us. Over a hundred easily.
Quoted 2 lines
What endianess have you chosen for your project and why?
You don't really want to start this holy war, do you? That aside, usually big endian is more useful in applications moving networking type traffic or a fair amount of graphics processing. Little endian is handy if you are porting applications from Windows or a lot of your software is written in little endian.
That's my $.02.
-Steve
Signature · 1 line
Steven J. Hill - Embedded SW Engineer
No, I have been involved with too many sorties in the war already. I was just asking if there was any issues with one side or the other from a purely technical aspect.
Quoted 21 lines · Steven J. Hill
Quoted 4 lines · Marc Karasek
How many of you are involved with embedded linux development using a MIPS processor?
A fair number of us. Over a hundred easily.
Quoted 2 lines
What endianess have you chosen for your project and why?
You don't really want to start this holy war, do you? That aside, usually big endian is more useful in applications moving networking type traffic or a fair amount of graphics processing. Little endian is handy if you are porting applications from Windows or a lot of your software is written in little endian.
That's my $.02.
-Steve
Signature · 1 line
Steven J. Hill - Embedded SW Engineer
Signature · 8 lines
/************************* Marc Karasek Sr. Firmware Engineer iVivity Inc. [email protected] 678.990.1550 x238 678.990.1551 Fax *************************/
Quoted 7 lines
Subject: Questions?
From: Marc Karasek <[email protected]>
To: Linux MIPS <[email protected]>
Date: 06 Mar 2002 12:25:11 -0500What endianess have you chosen for your project and why?
LE. That's all the NEC VR41XX support so I had no choice.
Mike McDonald
[email protected]
My company develops embedded MIPS systems, and Linux is one of our supported operating systems.
We chose big-endian, mostly because it seemed the right choice given the state of the tree. Some customers have recompiled our code to run little-endian with little problem, tho.
Matt
--
Matthew D. Dharm Senior Software Designer Momentum Computer Inc. 1815 Aston Ave. Suite 107 (760) 431-8663 X-115 Carlsbad, CA 92008-7310 Momentum Works For You www.momenco.com
Quoted 30 lines
-----Original Message-----
From: [email protected] [mailto:[email protected]]On Behalf Of Marc Karasek
Sent: Wednesday, March 06, 2002 9:25 AM
To: Linux MIPS
Subject: Questions?I have some general questions for all:
How many of you are involved with embedded linux development using a MIPS processor?
What endianess have you chosen for your project and why?
If you have not guessed it, I am involved with a MIPS/Linux embedded project and we are trying to determine if there are any pros or cons in
one endianess over the other.--
/*************************
Marc Karasek
Sr. Firmware Engineer
iVivity Inc.
[email protected]
678.990.1550 x238
678.990.1551 Fax
*************************/
----- Original Message -----
From: "Marc Karasek" <[email protected]>
To: "Linux MIPS" <[email protected]>
Sent: Wednesday, March 06, 2002 12:25 PM
Subject: Questions?
Quoted 1 line
What endianess have you chosen for your project
little
Quoted 1 line
and why?
1. to match endianness with my x86 cross-dev build system
2. hardware quirks
Regards,
Brad
Quoted 1 line · Marc Karasek
What endianess have you chosen for your project and why?
The MIPS world is irredemiably split, and the pull between SGI (always big-endian, M68000 heritage and Sun compatibility) and Linux' tendency to see the x86 as the universe has left Linux/MIPS split too.
As software tool and prototyping board supplier, we just know that everything we do has to work either way.
If you can change that, it would be great! :-)
--
Dominic Sweetman,
Algorithmics Ltd
The Fruit Farm, Ely Road, Chittering, CAMBS CB5 9PH, ENGLAND
phone: +44 1223 706200 / fax: +44 1223 706250 / direct: +44 1223 706205
http://www.algor.co.uk
Quoted 9 lines · Marc Karasek
How many of you are involved with embedded linux development using a MIPS processor?
What endianess have you chosen for your project and why?
If you have not guessed it, I am involved with a MIPS/Linux embedded project and we are trying to determine if there are any pros or cons in one endianess over the other.
The MIPS ABI only covers big endian systems - every "real" MIPS UNIX system is big endian. Everything else is a GNU extension. There is hardly any reason to choose a particular byteorder as usually endianess swapping takes so little CPU time that it isn't even meassurable but so I'm told there are exceptions. If portability of software you're going to write wrt. external data representation (disk or network) is of any importance then I suggest you use a system of the opposite endianess which trip problems much faster.
Ralf
Quoted 10 lines · Ralf Baechle
Quoted 8 lines · Marc Karasek
How many of you are involved with embedded linux development using a MIPS processor?
What endianess have you chosen for your project and why?
If you have not guessed it, I am involved with a MIPS/Linux embedded project and we are trying to determine if there are any pros or cons in one endianess over the other.
Quoted 8 lines
The MIPS ABI only covers big endian systems - every "real" MIPS UNIX system is big endian. Everything else is a GNU extension. There is hardly any reason to choose a particular byteorder as usually endianess swapping takes so little CPU time that it isn't even meassurable but so I'm told there are exceptions. If portability of software you're going to write wrt. external data representation (disk or network) is of any importance then I suggest you use a system of the opposite endianess which trip problems much faster.
I really like the last part! ;-)
BTW, you forgot to mention to go for a full 64-bit port, to trip even more problems faster :-)
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- [email protected]
In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
Quoted 9 lines · Geert Uytterhoeven
Quoted 8 lines
The MIPS ABI only covers big endian systems - every "real" MIPS UNIX system is big endian. Everything else is a GNU extension. There is hardly any reason to choose a particular byteorder as usually endianess swapping takes so little CPU time that it isn't even meassurable but so I'm told there are exceptions. If portability of software you're going to write wrt. external data representation (disk or network) is of any importance then I suggest you use a system of the opposite endianess which trip problems much faster.
Quoted 4 lines
I really like the last part! ;-)
BTW, you forgot to mention to go for a full 64-bit port, to trip even more problems faster :-)
Fortunately in practice that hasn't been a minefield as big as you'd imagine.
Ralf
Quoted 5 lines · Ralf Baechle
The MIPS ABI only covers big endian systems - every "real" MIPS UNIX system is big endian. Everything else is a GNU extension. There is hardly any reason to choose a particular byteorder as usually endianess swapping takes so little CPU time that it isn't even meassurable but so I'm told there are exceptions.
To me, byte swapping on MIPS actually seems rather expensive. The code for htonl (linux/byteorder/swab.h) ends up something like this:
srl $5,$4,8
andi $5,$5,0xff00
srl $2,$4,24
andi $3,$4,0xff00
or $2,$2,$5
sll $3,$3,8
or $2,$2,$3
sll $4,$4,24This may not be an issue if it is only needed a few times per packet, but my system must byte-swap (LE to BE) about 500KB (or 4mb) per second. Actually, I save a bit of work by combining the byte swapping with the memory move, just after copy_from_user, and looks something like:
unsigned char a, b, c, d, *mptr; a = mptr[0]; b = mptr[1]; c = mptr[2]; d = mptr[3]; mptr[0] = d; mptr[1] = c; mptr[2] = b; mptr[3] = a;
This method works, but it is still 8 instructions per word. Yuck! Does anyone know of a _decent_ way to handle this on MIPS?
All the best,
-Richard
Quoted 2 lines · Ralf Baechle
The MIPS ABI only covers big endian systems - every "real" MIPS UNIX system is big endian.
Except Decstations. And Sony NeWS (remember that one). And anything running on those NEC Vr41xx systems which were designed for WinCE and don't run big-endian at all. There never was a consensus...
Mapping the MIPS ABI to little-endian presents no problems, as far as I know: obviously since it's a binary compatibility standard it has to make a choice...
Quoted 3 lines
There is hardly any reason to choose a particular byteorder as usually endianess swapping takes so little CPU time that it isn't even meassurable but so I'm told there are exceptions.
I think it's often done for software-portability reasons; sometimes because some hardware works both ways but has some irritating flaw in its less-favoured organisation.
System software (kernels, libraries) tends to work both ways, because it's written by people who thought about it. Huge applications which have only ever run on x86 and friends often don't work.
Finding the problems faster is a counsel of perfection: in practice, a lot of us just want something that works, tomorrow.
Swapping probably is an unmeasurable load: even if it takes 8-10 instructions per word on a 500MHz CPU that's 200Mbytes/s. But it is ugly, particularly when it's required to restore correct byte sequence because of a naive hardware interface (one, for example, which connects the MIPS CPU data lines to the same-numbered PCI ones...)
So there are arguments on both sides, and players in both camps. I believe it's too late to corral all MIPS/Linux activity into one endianness or the other.
Embrace bi-endianness!
Signature · 5 lines
Dominic Sweetman, Algorithmics Ltd The Fruit Farm, Ely Road, Chittering, CAMBS CB5 9PH, ENGLAND phone: +44 1223 706200 / fax: +44 1223 706250 / direct: +44 1223 706205 http://www.algor.co.uk