EMU10K1 DSP programs
Hi all!
Is it possible to load DSP programs to the EMU10K1 chip? The alsa-tools package contains a modified as10k1 that allows you to assemble such programs, but there's no information about how to upload them to the processor.
Thanks a lot,
M. S.
-----------------------------------------------------------------
Martin Soto
AG Software Engineering
Universitaet Kaiserslautern Tel: +49 (631) 205-3449
Kaiserslautern, Germany E-mail: [email protected]
-----------------------------------------------------------------
-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf
Quoted 6 lines · Martin Soto
Hi all!
Is it possible to load DSP programs to the EMU10K1 chip? The alsa-tools package contains a modified as10k1 that allows you to assemble such programs, but there's no information about how to upload them to the processor.
The work has not been finished at all. The changes in assembler are incomplete and the user space linker/loader program is missing at all.
Jaroslav
-----
Jaroslav Kysela <[email protected]>
Linux Kernel Sound Maintainer
ALSA Project http://www.alsa-project.org
SuSE Linux http://www.suse.com
-------------------------------------------------------
Sponsored by: AMD - Your access to the experts on Hammer Technology! Open Source & Linux Developers, register now for the AMD Developer Symposium. Code: EX8664 http://www.developwithamd.com/developerlab
Quoted 8 lines · Jaroslav Kysela
Quoted 4 lines · Martin Soto
Is it possible to load DSP programs to the EMU10K1 chip? The alsa-tools package contains a modified as10k1 that allows you to assemble such programs, but there's no information about how to upload them to the processor.
The work has not been finished at all. The changes in assembler are incomplete and the user space linker/loader program is missing at all.
Thanks for the answer. I actually discovered part of it yesterday after I wrote my original mail, by looking directly at the driver code. I'm actually interested in writing a patch loader/manager, and as far as I can see, the driver interface is already there. I haven't tested it thoroughly though, so I'm not sure it is completely operational. But it looks good.
And, by the way, I have a question regarding it. In the hardware dependant ioctl interface to the EMU10K1 there are two ioctls, SNDRV_EMU10K1_IOCTL_CODE_PEEK and SNDRV_EMU10K1_IOCTL_CODE_POKE, that allow you to read the DSP code and to actually upload new code. Part of what SNDRV_EMU10K1_IOCTL_CODE_POKE does is defining new (mixer) controls and eventually deleting those that are not needed any more.
However, I didn't find a way to know which current mixer controls are *actually* associated to general purpose registers in the FX8010. Of course, I could read the code in emufx.c and determine it from there, but that would make my code very sensible to changes in the driver. I just though of using the mixer/control interface in alsalib to find all controls, and try to delete them with CODE_POKE, hoping that the driver will only delete those that are connected to GPRs, but that looks too much like a hack. Is there a more elegant way to handle that?
Cheers,
M. S.
-----------------------------------------------------------------
Martin Soto
AG Software Engineering
Universitaet Kaiserslautern Tel: +49 (631) 205-3449
Kaiserslautern, Germany E-mail: [email protected]
-----------------------------------------------------------------
-------------------------------------------------------
Sponsored by: AMD - Your access to the experts on Hammer Technology! Open Source & Linux Developers, register now for the AMD Developer Symposium. Code: EX8664 http://www.developwithamd.com/developerlab
Quoted 24 lines · Martin Soto
Quoted 8 lines · Jaroslav Kysela
Quoted 4 lines · Martin Soto
Is it possible to load DSP programs to the EMU10K1 chip? The alsa-tools package contains a modified as10k1 that allows you to assemble such programs, but there's no information about how to upload them to the processor.
The work has not been finished at all. The changes in assembler are incomplete and the user space linker/loader program is missing at all.
Thanks for the answer. I actually discovered part of it yesterday after I wrote my original mail, by looking directly at the driver code. I'm actually interested in writing a patch loader/manager, and as far as I can see, the driver interface is already there. I haven't tested it thoroughly though, so I'm not sure it is completely operational. But it looks good.
And, by the way, I have a question regarding it. In the hardware dependant ioctl interface to the EMU10K1 there are two ioctls,
SNDRV_EMU10K1_IOCTL_CODE_PEEKandSNDRV_EMU10K1_IOCTL_CODE_POKE, that allow you to read the DSP code and to actually upload new code. Part of whatSNDRV_EMU10K1_IOCTL_CODE_POKEdoes is defining new (mixer) controls and eventually deleting those that are not needed any more.
Quoted 8 lines
However, I didn't find a way to know which current mixer controls are *actually* associated to general purpose registers in the FX8010. Of course, I could read the code in
emufx.cand determine it from there, but that would make my code very sensible to changes in the driver. I just though of using the mixer/control interface in alsalib to find all controls, and try to delete them withCODE_POKE, hoping that the driver will only delete those that are connected to GPRs, but that looks too much like a hack. Is there a more elegant way to handle that?
I've added gpr_list_control* variables to emu10k1_fx8010_code_t. The SNDRV_EMU10K1_IOCTL_CODE_PEEK will fill these variables for you. Note that all this code in emufx.c is mostly untested, so give me feedback, what features/functions need to be corrected.
Jaroslav
-----
Jaroslav Kysela <[email protected]>
Linux Kernel Sound Maintainer
ALSA Project http://www.alsa-project.org
SuSE Linux http://www.suse.com
-------------------------------------------------------
Sponsored by: AMD - Your access to the experts on Hammer Technology! Open Source & Linux Developers, register now for the AMD Developer Symposium. Code: EX8664 http://www.developwithamd.com/developerlab
Quoted 17 lines · Jaroslav Kysela
Quoted 7 lines · Martin Soto
And, by the way, I have a question regarding it. In the hardware dependant ioctl interface to the EMU10K1 there are two ioctls,
SNDRV_EMU10K1_IOCTL_CODE_PEEKandSNDRV_EMU10K1_IOCTL_CODE_POKE, that allow you to read the DSP code and to actually upload new code. Part of whatSNDRV_EMU10K1_IOCTL_CODE_POKEdoes is defining new (mixer) controls and eventually deleting those that are not needed any more.Quoted 8 lines
However, I didn't find a way to know which current mixer controls are *actually* associated to general purpose registers in the FX8010. Of course, I could read the code in
emufx.cand determine it from there, but that would make my code very sensible to changes in the driver. I just though of using the mixer/control interface in alsalib to find all controls, and try to delete them withCODE_POKE, hoping that the driver will only delete those that are connected to GPRs, but that looks too much like a hack. Is there a more elegant way to handle that?
Quoted 4 lines
I've added gpr_list_control* variables to
emu10k1_fx8010_code_t. TheSNDRV_EMU10K1_IOCTL_CODE_PEEKwill fill these variables for you. Note that all this code inemufx.cis mostly untested, so give me feedback, what features/functions need to be corrected.
That was exactly what I was looking for, thanks! I'll try to write at least a simple loader in the following days to see if everything works properly.
Cheers,
M. S.
-----------------------------------------------------------------
Martin Soto
AG Software Engineering
Universitaet Kaiserslautern Tel: +49 (631) 205-3449
Kaiserslautern, Germany E-mail: [email protected]
-----------------------------------------------------------------
-------------------------------------------------------
This SF.NET email is sponsored by: AMD - Your access to the experts on Hammer Technology! Open Source & Linux Developers, register now for the AMD Developer Symposium. Code: EX8664
http://www.developwithamd.com/developerlab
Quoted 6 lines · Martin Soto
Hi all!
Is it possible to load DSP programs to the EMU10K1 chip? The alsa-tools package contains a modified as10k1 that allows you to assemble such programs, but there's no information about how to upload them to the processor.
i have not tried it out but there are some ioctl which allow you to poke and peek
the dsp instruction memory.
ALSA uses a fair amount of dsp code for its own. I am not quite sure what has to be done to remove the alsa dsp code (remove the mixers controling
the gprs etc)
have a look atalsa-kernel/pci/emu10k1/emufx.c
And if you have any success tell me.
I would like to load up patches into the DSP too.
-------------------------------------------------------
This SF.NET email is sponsored by: AMD - Your access to the experts on Hammer Technology! Open Source & Linux Developers, register now for the AMD Developer Symposium. Code: EX8664
http://www.developwithamd.com/developerlab