Skip to contentSkip to conversation

HDSP 9652 MIDI - A timing disaster?

DISCUSSION Mark Knecht 4 participants 6 messages Jan 11, 2003 – Jan 14, 2003

lore
Share & tools
lore
#0 lore raw

Hi,
I asked about this two weeks ago but got no responses. I'm hoping
this time I hear something back from other owners of the same hardware.

I recently purchased an RME HDSP 9652 card. The card is working fine
for audio, but the MIDI interface is a timing disaster. The interface works, but won't keep time. A 2 minute song is Rosegarden takes abut 2:45 to play every time. You can hear how the HDSP isn't delivering closely spaced MIDI events together, but is sort of smearing them out.

My machine is set up using the PlanetCCRMA system. According to
Synaptic my Alsa driver is from CVS:20021216. Jack is 0.44. This machine works just fine with the MidiMan 2x2 interface. No timing problems at all.

Has anyone else purchased this card? Used the MIDI interface on this
card? Gotten better results with this card?

Can anyone suggest how I could go about fixing this myself? I'm not a
programmer, so really hacking the code is doubtful, but this driver is acting like there is just a basic mistake somewhere. Possibly I could find it if I knew where to look.

I hope someone will respond to this email so we can get something
going to get this fixed. I really need this interface to operate soon.

Thanks in advance,
Mark

-------------------------------------------------------
This SF.NET email is sponsored by:
SourceForge Enterprise Edition + IBM + LinuxWorld = Something 2 See!
http://www.vasoftware.com

#1 lore raw
Quoted 5 lines · Mark Knecht

I recently purchased an RME HDSP 9652 card. The card is working fine
for audio, but the MIDI interface is a timing disaster. The interface works, but won't keep time. A 2 minute song is Rosegarden takes abut 2:45 to play every time. You can hear how the HDSP isn't delivering closely spaced MIDI events together, but is sort of smearing them out.

The hdsp driver doesn't send more than one MIDI byte per timer tick. IMHO it should be modified to send in a loop until the FIFO is full (however, I don't know if the HDSP has a FIFO at all). And it should start sending in output_trigger() instead of delaying it to the next timer tick.

HTH
Clemens

-------------------------------------------------------
This SF.NET email is sponsored by:
SourceForge Enterprise Edition + IBM + LinuxWorld = Something 2 See!
http://www.vasoftware.com

#2 lore raw
Quoted 9 lines
Quoted 5 lines · Mark Knecht

I recently purchased an RME HDSP 9652 card. The card is working fine
for audio, but the MIDI interface is a timing disaster. The interface works, but won't keep time. A 2 minute song is Rosegarden takes abut 2:45 to play every time. You can hear how the HDSP isn't delivering closely spaced MIDI events together, but is sort of smearing them out.

The hdsp driver doesn't send more than one MIDI byte per timer tick. IMHO it should be modified to send in a loop until the FIFO is full

that's what this tried to do:

	if (hmidi->output) {
		if (!snd_rawmidi_transmit_empty (hmidi->output)) {
			if ((n_pending = snd_hdsp_midi_output_possible (hmidi->hdsp, hmidi->id)) > 0) {
				if (n_pending > sizeof (buf))
					n_pending = sizeof (buf);
				
				if ((to_write = snd_rawmidi_transmit (hmidi->output, buf, n_pending)) > 0) {
					for (i = 0; i < to_write; ++i) 
						snd_hdsp_midi_write_byte (hmidi->hdsp, hmidi->id, buf[i]);
				} else {
					clear_timer = 1;
				}
			}
		} else {
			clear_timer = 1;
		}

how does this end up writing only a single byte? unless n_pending is always either 0 or 1, which on closer inspection, i see that it is ... yikes.

Quoted 1 line

(however, I don't know if the HDSP has a FIFO at all). And it should start

it does have a FIFO.

Quoted 1 line

sending in output_trigger() instead of delaying it to the next timer tick.

hmm. i modelled this code on another PCI driver that had MIDI support. is there an example you can point me to that starts from within the equivalent output_trigger?

--p

-------------------------------------------------------
This SF.NET email is sponsored by: FREE SSL Guide from Thawte are you planning your Web Server Security? Click here to get a FREE Thawte SSL guide and find the answers to all your SSL security issues.
http://ads.sourceforge.net/cgi-bin/redirect.pl?thaw0026en

#3 lore raw
Quoted 9 lines · Paul Davis
Quoted 2 lines

The hdsp driver doesn't send more than one MIDI byte per timer tick. IMHO it should be modified to send in a loop until the FIFO is full

that's what this tried to do:
(...)
how does this end up writing only a single byte? unless n_pending is always either 0 or 1, which on closer inspection, i see that it is ... yikes.

Quoted 5 lines
Quoted 1 line

sending in output_trigger() instead of delaying it to the next timer tick.

hmm. i modelled this code on another PCI driver that had MIDI support. is there an example you can point me to that starts from within the equivalent output_trigger?

e.g. isa/sb/sb8_midi.c or drivers/mpu401/mpu401_uart.c

And both output one byte at a time in a loop until the output fails. (However, snd_sb8dsp_midi_output_write() doesn't check for a full FIFO.)

HTH
Clemens

-------------------------------------------------------
This SF.NET email is sponsored by: FREE SSL Guide from Thawte are you planning your Web Server Security? Click here to get a FREE Thawte SSL guide and find the answers to all your SSL security issues.
http://ads.sourceforge.net/cgi-bin/redirect.pl?thaw0026en

#4 lore raw

At Mon, 13 Jan 2003 15:28:58 +0100 (MET),

Quoted 13 lines · Clemens Ladisch
Quoted 11 lines · Paul Davis
Quoted 2 lines

The hdsp driver doesn't send more than one MIDI byte per timer tick. IMHO it should be modified to send in a loop until the FIFO is full

that's what this tried to do:
(...)
how does this end up writing only a single byte? unless n_pending is always either 0 or 1, which on closer inspection, i see that it is ... yikes.

Quoted 1 line

sending in output_trigger() instead of delaying it to the next timer tick.

Quoted 8 lines
Quoted 3 lines

hmm. i modelled this code on another PCI driver that had MIDI support. is there an example you can point me to that starts from within the equivalent output_trigger?

e.g. isa/sb/sb8_midi.c or drivers/mpu401/mpu401_uart.c

And both output one byte at a time in a loop until the output fails. (However, snd_sb8dsp_midi_output_write() doesn't check for a full FIFO.)

well, generally it's not a good style to process in such a loop in the primary interrupt handler. we should rewrite them using tasklet...

Takashi

-------------------------------------------------------
This SF.NET email is sponsored by: FREE SSL Guide from Thawte are you planning your Web Server Security? Click here to get a FREE Thawte SSL guide and find the answers to all your SSL security issues.
http://ads.sourceforge.net/cgi-bin/redirect.pl?thaw0026en

#5 lore raw
In reply to Clemens Ladisch
Quoted 7 lines · Clemens Ladisch
Quoted 5 lines · Mark Knecht

I recently purchased an RME HDSP 9652 card. The card is working fine
for audio, but the MIDI interface is a timing disaster. The interface works, but won't keep time. A 2 minute song is Rosegarden takes abut 2:45 to play every time. You can hear how the HDSP isn't delivering closely spaced MIDI events together, but is sort of smearing them out.

Quoted 5 lines

The hdsp driver doesn't send more than one MIDI byte per timer tick. IMHO it should be modified to send in a loop until the FIFO is full (however, I don't know if the HDSP has a FIFO at all). And it should start sending in output_trigger() instead of delaying it to the next timer tick.

Clemens,
Thanks for the response. One comment I forgot to make in the first
post. This MIDI interface works fine under Windows, so whatever causes the problem is purely a Alsa MIDI issue. If we can figure it out, then we can fix it.

I agree that it sounds like this sort of one note per timer tick.
When the interface is supposed to send a chord, it sends what sounds like an arpegiated chord. It's all smeared out.

Is there some example code I could look at to understand implementing
a FIFO? However, if there is a FIFO Full indication, doesn't we need to know _how_ it's indicated? I would assume it's different for all cards? (Bus possibly similar for cards from the same manufacturer?

Also, this is the HDSP 9652, which is a single PCI card. Is this
problem showing up for the DigiFace/MultiFace type cards?

Thanks,
Mark

-------------------------------------------------------
This SF.NET email is sponsored by: FREE SSL Guide from Thawte are you planning your Web Server Security? Click here to get a FREE Thawte SSL guide and find the answers to all your SSL security issues.
http://ads.sourceforge.net/cgi-bin/redirect.pl?thaw0026en