Problem w/2.5.59 & orinoco_pci (works w/2.4.18)
This is on an old Dell Pentium/100. This may or may not be related, but it requires pci=conf1 (for 2.4) or pci=conf2 (for 2.5) to get proper lspci output. I get similar results with Jouni Malinen's hostap_pci driver (works in 2.4, not in 2.5), which makes me think something changed in 2.5 that broke both drivers. This is a Linksys WMP11 PCI wireless adapter.
I don't have anything fancy (himem, preempt, etc) compiled into the kernel, just the basics for a wireless AP/firewall.
Thanks for any help you can provide! I'm happy to supply any additional information or test solutions upon request. I'm not subscribed, so please cc me.
-Cory Bell
Broken (vanilla 2.5.59):
Feb 8 12:42:45 kernel: Reset done.........................................................................................................................................................................................................................................................; Feb 8 12:42:45 kernel: Clear Reset..................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................; Feb 8 12:42:45 kernel: pci_cor : reg = 0x0 - 3115F85 - 3115D91 Feb 8 12:42:45 kernel: hermes @ MEM 0xc881d000: Timeout waiting for card to reset (reg=0x0000)! Feb 8 12:42:45 kernel: eth2: failed to initialize firmware (err = -110) Feb 8 12:42:45 kernel: eth2: Failed to register net device
Working (RedHat 2.4.18-24.8.0):
Feb 8 20:01:57 kernel: Reset done...................................................................................................................................................................................................................................................; Feb 8 20:01:57 kernel: Clear Reset....................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................................; Feb 8 20:01:57 kernel: pci_cor : reg = 0x0 - 1629 - 15F7 Feb 8 20:01:58 kernel: eth2: Channel out of range (0)! Feb 8 20:01:58 kernel: eth2: Error -110 writing Tx descriptor to BAP Feb 8 20:01:58 last message repeated 10 times
lspci (2.4 & 2.5 are identical):
00:07.0 Network controller: Harris Semiconductor Prism 2.5 Wavelan chipset (rev 01)
Subsystem: Unknown device 1737:3874
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 15
Region 0: Memory at 3efff000 (32-bit, prefetchable) [size=4K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00: 60 12 73 38 13 01 90 02 01 00 80 02 08 20 00 00
10: 08 f0 ff 3e 00 00 00 00 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 37 17 74 38
30: 00 00 00 00 dc 00 00 00 00 00 00 00 0f 01 00 00
40: 80 80 00 00 00 00 00 00 00 00 00 00 00 00 00 00
50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
70: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
80: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
d0: 00 00 00 00 00 00 00 00 00 00 00 00 01 00 02 7e
e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
Quoted 7 lines · Cory Bell
This is on an old Dell Pentium/100. This may or may not be related, but it requires pci=conf1 (for 2.4) or pci=conf2 (for 2.5) to get proper lspci output. I get similar results with Jouni Malinen's
hostap_pcidriver (works in 2.4, not in 2.5), which makes me think something changed in 2.5 that broke both drivers. This is a Linksys WMP11 PCI wireless adapter.
Quoted 8 lines
I don't have anything fancy (himem, preempt, etc) compiled into the kernel, just the basics for a wireless AP/firewall.
Thanks for any help you can provide! I'm happy to supply any additional information or test solutions upon request. I'm not subscribed, so please cc me.
-Cory Bell
This hardware never worked in my computer (tool old). I would
suggest complaining on the kernel mailing list with the details above (and below - plus lspci -v), as it seems to point out to a generic PCI problem, not a driver problem.
Regards,
Jean