Skip to contentSkip to conversation

PPPoE Synchronous mode delivers very much packets errors

DISCUSSION Marcello 1 participant 1 message Sep 28, 2003

lore
Share & tools
lore

Marcello

author
#0 lore raw

Hi all.

I've tried today to enable the PPP Synchronous mode for my PPPoE connection , and ifconfig reports a very strange thing:

melchior:/home/melchior# ifconfig
eth0      Link encap:Ethernet  HWaddr 00:40:F4:55:A1:40
          inet addr:192.168.254.1  Bcast:192.168.254.255 
Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:774 errors:0 dropped:0 overruns:0 frame:0
          TX packets:579 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:100
          RX bytes:362290 (353.7 KiB)  TX bytes:51218 (50.0 KiB)
          Interrupt:19 Base address:0x1f00

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:80 errors:0 dropped:0 overruns:0 frame:0 TX packets:80 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0
RX bytes:5128 (5.0 KiB) TX bytes:5128 (5.0 KiB)

ppp0 Link encap:Point-to-Point Protocol

          inet addr:80.180.66.58  P-t-P:192.168.100.1 

Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1 RX packets:189 errors:212 dropped:0 overruns:0 frame:0 TX packets:129 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3
RX bytes:67413 (65.8 KiB) TX bytes:8740 (8.5 KiB)

melchior:/home/melchior#

Look at the ppp0 section , and look at the RX packets area , the corrupted packages are MORE than the correct packages !! With async mode this doesn't happen .
Someone have said me that It could be a kernel bug , is this possible?

During the connection I don't see any problem , all runs perfectly .

Thank you for your attention :

lsmod

Module                  Size  Used by    Not tainted
ppp_deflate             3448   0  (autoclean)
bsd_comp                4312   0  (autoclean)
ppp_synctty             6208   1  (autoclean)
zlib_inflate           18404   0  (autoclean) [ppp_deflate]
zlib_deflate           18008   0  (autoclean) [ppp_deflate]
af_packet              13352   2  (autoclean)
hdlc                    1608   0  (unused)
syncppp                11120   0  [hdlc]
sunrpc                 67840   0  (unused)
sr_mod                 15704   0  (autoclean)
ext3                   62980   3  (autoclean)
jbd                    41716   3  (autoclean) [ext3]
serial                 48228   0  (autoclean)
n_hdlc                  6720   1
ide-cd                 32096   0
cdrom                  28672   0  [sr_mod ide-cd]
ppp_generic            17412   3  [ppp_deflate bsd_comp ppp_synctty]
slhc                    5440   0  [ppp_generic]
hid                    21572   0  (unused)
ehci-hcd               17260   0  (unused)
thermal                 6308   0  (unused)
processor               8376   0  [thermal]
fan                     1632   0  (unused)
button                  2540   0  (unused)
agpgart                13808   0  (unused)
cmpci                  31492   1
soundcore               3972   4  [cmpci]
evdev                   4640   0  (unused)
mousedev                4180   1
sg                     27644   0  (unused)
ide-scsi               10224   0
ch                     12560   0  (unused)
scsi_mod               57108   4  [sr_mod sg ide-scsi ch]
ip_gre                  9024   0  (unused)
8139too                14952   1
mii                     2464   0  [8139too]
crc32                   2880   0  [8139too]
keybdev                 2084   0  (unused)
input                   3520   0  [hid evdev mousedev keybdev]
usb-uhci               23280   0  (unused)
usbcore                40388   0  [hid ehci-hcd usb-uhci]

unix 15308 215 (autoclean)
melchior:/home/melchior#

lspci -vvv

melchior:/home/melchior# lspci -vvv
00:00.0 Host bridge: VIA Technologies, Inc. VT8377 [KT400 AGP] Host
Bridge
        Subsystem: VIA Technologies, Inc.: Unknown device 0000
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
        Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
        Latency: 8
        Region 0: Memory at e0000000 (32-bit, prefetchable) [size=256M]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
                Command: RQ=32 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit-
FW- Rate=<none>
        Capabilities: [c0] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT8235 PCI Bridge (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff
Memory behind bridge: dde00000-dfefffff
Prefetchable memory behind bridge: d5c00000-ddcfffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RT8139
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 19
Region 0: I/O ports at ec00 [size=256]
Region 1: Memory at dfffff00 (32-bit, non-prefetchable)
[size=256]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0-,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:0c.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev
10)
Subsystem: Micro-Star International Co., Ltd.: Unknown device
5900
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 96 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at e800 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. USB
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 96, cache line size 08
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at e400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if 20 [EHCI])
Subsystem: VIA Technologies, Inc. USB 2.0
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 96, cache line size 10
Interrupt: pin D routed to IRQ 21
Region 0: Memory at dffffe00 (32-bit, non-prefetchable)
[size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: VIA Technologies, Inc.: Unknown device 0000
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:11.1 IDE interface: VIA Technologies, Inc. VT82C586/B/686A/B PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc. VT8235 Bus Master
ATA133/100/66/33 IDE Control: I/O+ Mem+ BusMaster+ SpecCycle-
MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 255
Region 4: I/O ports at fc00 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 VGA compatible controller: nVidia Corporation NV20 [GeForce3 Ti 200] (rev a3) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Latency: 96 (1250ns min, 250ns max)
        Interrupt: pin A routed to IRQ 16
        Region 0: Memory at de000000 (32-bit, non-prefetchable)

[size=16M]
Region 1: Memory at d8000000 (32-bit, prefetchable) [size=64M] Region 2: Memory at ddc80000 (32-bit, prefetchable) [size=512K] Expansion ROM at dfef0000 [disabled] [size=64K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4

                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW-

Rate=<none>

melchior:/home/melchior#

Thank you

Marcello