Skip to contentSkip to conversation

Problem in 2.6.0-test9-mm1 with siimage+hdparm

DISCUSSION Krisztian VASAS 2 participants 3 messages Nov 5, 2003

lore
Share & tools
lore
#0 lore raw

Hello all...

I've got an Abit NF7-S v2.0 mainboard with an Athlon XP 2000+ CPU.

Yesterday I've compiled the 2.6.0-test9 kernel with -mm1 patch. My system is on the first sata device (/dev/hde).

After reboot I've noticed an Oops after setting dma and other settings with hdparm. Without -mm1 patch the machine works well.

After the oops I've tried to find what the problem was.

hdparm -c1 /dev/hde -> nothing was happened, switched off... hdparm -d1 /dev/hde -> Oops...

I've got this messages:

hde: DMA timeout retry status error: status=0x58 { DriveReady SeekComplete DataRequest }

ide2: reset phy, status=0x00000113 siimage_reset

.
.
.

Buffer I/O error on device hde2, logical block 97865 lost page write due to I/O error on hde2

.
.
.

EXT3-fs error (device hde2) in start_transaction: Journal has aborted

The rootfs is /dev/hde2.

Please cc the answers to my address, because I'm not lkml member...

Thanks:

IroNiQ

Signature · 2 lines
Web: http://ironiq.hu
E-mail: [email protected]
#1 lore raw
Quoted 15 lines · Krisztian VASAS

Hello all...

I've got an Abit NF7-S v2.0 mainboard with an Athlon XP 2000+ CPU.

Yesterday I've compiled the 2.6.0-test9 kernel with -mm1 patch. My system is on the first sata device (/dev/hde).

After reboot I've noticed an Oops after setting dma and other settings with hdparm. Without -mm1 patch the machine works well.

After the oops I've tried to find what the problem was.

hdparm -c1 /dev/hde -> nothing was happened, switched off... hdparm -d1 /dev/hde -> Oops...

Quoted 6 lines

I've got this messages:

hde: DMA timeout retry status error: status=0x58 { DriveReady SeekComplete DataRequest }

ide2: reset phy, status=0x00000113 siimage_reset

Strange enough I have an Abit NF7-s Rev2.0 as well, but for me the driver works - somehow. I havbe latest bios 1.9 (modified with latest silicon image bios). Since siimage 1.06 drvier. I have DMA without using hdparm, but it is not as fast as in windows. With kernel 2.6 tranfer dropped very much to about 20mb/s (playing with read-aheed didn't help). But I am getting this error messages in dmesg and at boot up (that's why I commented it out in siimage.c):

hde: sata_error = 0x00000000, watchdog = 0, siimage_mmio_ide_dma_test_irq

Other than that it runs fine - forgetting that performance it bad right now. Tried various shedulers, but didn't help. With kernel 2.4.22-ac4 I had about 37mb/sec, now only 20mb/sec...

Prakash

#2 lore raw
Quoted 8 lines · On 2003-11-05 Prakash K. Cheemplavam wrote:

Strange enough I have an Abit NF7-s Rev2.0 as well, but for me the driver works - somehow. I havbe latest bios 1.9 (modified with latest silicon image bios). Since siimage 1.06 drvier. I have DMA without using hdparm, but it is not as fast as in windows. With kernel 2.6 tranfer dropped very much to about 20mb/s (playing with read-aheed didn't help). But I am getting this error messages in dmesg and at boot up (that's why I commented it out in siimage.c):

Quoted 5 lines

hde: sata_error = 0x00000000, watchdog = 0, siimage_mmio_ide_dma_test_irq

Other than that it runs fine - forgetting that performance it bad right now. Tried various shedulers, but didn't help. With kernel 2.4.22-ac4 I had about 37mb/sec, now only 20mb/sec...

I haven't problem with the speed. I'd like to set up DMA to the disk and the -d switch (using_dma) causes the panic. With vanilla 2.6.0-test9 everything works fine, no speed problem. But if I boot up with -mm1, I have to work without DMA on hde. And another interesting thing: hdparm -d1 /dev/hdd works fine, so the problem is somewhere in the siimage driver. I don't know exactly what changed, but something has been corrupted around the driver.

IroNiQ

Signature · 1 line
Krisztian VASAS <[email protected]>