Skip to contentSkip to conversation

USB/visor oops

DISCUSSION Dax Kelson 2 participants 2 messages Dec 7, 2003

lore
Share & tools
lore

Dax Kelson

author
#0 lore raw

After having had my Tre600 hotsyncing working fine with RHL9 I'm trying again after upgrading to Fedora. So far all I get are oops and hangs.

This is with the Fedora kernel 2.4.22-1.2115.nptl. This is with the uhci instead of usb-uhci.

hub.c: new USB device 00:1d.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x82d/0x300) is not claimed by any active driver.
usb.c: registered new driver serial
usbserial.c: USB Serial support registered for Generic
usbserial.c: USB Serial Driver core v1.4
usbserial.c: USB Serial support registered for Handspring Visor / Treo / Palm 4. 0 / Clie 4.x usbserial.c: Handspring Visor / Treo / Palm 4.0 / Clie 4.x converter detected
usbserial.c: Handspring Visor / Treo / Palm 4.0 / Clie 4.x converter now attache d to ttyUSB0 (or usb/tts/0 for devfs) usbserial.c: Handspring Visor / Treo / Palm 4.0 / Clie 4.x converter now attache d to ttyUSB1 (or usb/tts/1 for devfs) usbserial.c: USB Serial support registered for Sony Clie 3.5
visor.c: USB HandSpring Visor, Palm m50x, Treo, Sony Clie driver v1.7
uhci.c: bf80: host controller halted. very bad
usb.c: USB disconnect on device 00:1d.0-1 address 2
visor.c: Bytes In = 0 Bytes Out = 0

Unable to handle kernel NULL pointer dereference at virtual address 00000998
 printing eip:
f884556c
*pde = 37253067
*pte = 00000000
Oops: 0002
visor usbserial uhci i810_audio ac97_codec soundcore radeon agpgart vmnet vmmon parport_pc lp parport autofs orinoco_cs orinoco hermes ds yenta_socket pcmcia_
CPU:    0
EIP:    0060:[<f884556c>]    Tainted: PF
EFLAGS: 00010246

EIP is at usb_serial_disconnect [usbserial] 0x6c (2.4.22-1.2115.nptl)
eax: 00000000 ebx: f3830400 ecx: 00000000 edx: 00000000
esi: f383041c edi: 00000000 ebp: f3830400 esp: f7bc9f14
ds: 0068 es: 0068 ss: 0068
Process khubd (pid: 71, stackpage=f7bc9000)

Stack: f383041c 00000000 00000064 f8847520 f8847500 00000000 f4cc0980 f883032f
       e42f9200 f3830400 e42f9204 00000002 00000000 e42f9200 00000100 0000000a
       f7355a00 00000000 f8833270 f7355b0c 00000001 00000010 f4cc05c0 f8832c9c
Call Trace:   [<f8847520>] usb_serial_driver [usbserial] 0x20 (0xf7bc9f20)

[<f8847500>] usb_serial_driver [usbserial] 0x0 (0xf7bc9f24) [<f883032f>] usb_disconnect_R1a2445d3 [usbcore] 0x9f (0xf7bc9f30) [<f8833270>] usb_hub_port_connect_change [usbcore] 0x270 (0xf7bc9f5c) [<f8832c9c>] usb_hub_port_status [usbcore] 0x6c (0xf7bc9f70) [<f8833568>] usb_hub_events [usbcore] 0x2e8 (0xf7bc9f90) [<f8833605>] usb_hub_thread [usbcore] 0x45 (0xf7bc9fbc) [<f88335c0>] usb_hub_thread [usbcore] 0x0 (0xf7bc9fc4) [<f88335c0>] usb_hub_thread [usbcore] 0x0 (0xf7bc9fe0) [<c010741d>] kernel_thread_helper [kernel] 0x5 (0xf7bc9ff0)

Code: 89 90 98 09 00 00 8d 4e 58 ff 43 74 0f 8e 96 05 00 00 0f b6
#1 lore raw
Quoted 5 lines · Dax Kelson

After having had my Tre600 hotsyncing working fine with RHL9 I'm trying again after upgrading to Fedora. So far all I get are oops and hangs.

This is with the Fedora kernel 2.4.22-1.2115.nptl. This is with the uhci instead of usb-uhci.

Can you try 2.4.23? This problem should be fixed there.

thanks,

greg k-h