Skip to contentSkip to conversation

NAT setup

DISCUSSION Ben Becker 3 participants 4 messages Dec 19, 2003 – Dec 20, 2003

lore
Share & tools
lore

Ben Becker

author
#0 lore raw

Hello everybody,

I'm trying to figure out a way to set up basic NAT, but with the ability to allow users on the local side to use any static IP configuration. Quick Example: somebody has a static IP configured on their laptop, stays at a hotel with Internet access, and will be able to browse the Internet without changing their IP settings.

My first question is: does anybody know what this feature is called? Second question: Is it possible to do this with netfilter? I'm thinking this would require creating a new virtual interface for each user's configuration to match their gateway (among other things), but I'm hoping netfilter has some magical way of doing this (hoping). If not, does anybody know of any software that can do this?

Regards,
Ben Becker

#1 lore raw

Hi Ben,

Very interesting concept. There are two major parts to this:

1) Outbound packets from those static IP's to your gateway. this can be done by enabling proxy-arp on your gateway to answer to any arp request. This way the clients would hand over their traffic to your gateway. Subsequently your gateway would SNAT them and throw it on the Internet.

2) Inbound reply packets coming from the outside. This is a bit tricky because, once they're in and de-SNATed, your gateway must know where to send them to. Since your gateway has only one default route and no knowledge about those static IP's behind it, it would automatically send the reply packets back to the Internet. You might overcome this by blindly forwarding these ESTABLISHED incoming packets through your internal interface but you still need to somehow do an ARP for an IP outside your LAN segment. At this point I don't have any simple solution for that. But there are some very sharp ARP people here on the list who could hack something together for you or give you a pointer to an already hacked solution.

Ramin

Quoted 18 lines · Ben Becker

Hello everybody,

I'm trying to figure out a way to set up basic NAT, but with the ability to allow users on the local side to use any static IP configuration. Quick Example: somebody has a static IP configured on their laptop, stays at a hotel with Internet access, and will be able to browse the Internet without changing their IP settings.

My first question is: does anybody know what this feature is called? Second question: Is it possible to do this with netfilter? I'm thinking this would require creating a new virtual interface for each user's configuration to match their gateway (among other things), but I'm hoping netfilter has some magical way of doing this (hoping). If not, does anybody know of any software that can do this?

Regards,
Ben Becker

#2 lore raw

What you need is:
arp -s <Outside IP> <Outside MAC> pub
and a route to the <Outside IP> via the internal interface.

That should do the trick.

Regards
Søren Kent Jensen

----- Original Message -----
From: "Ramin Dousti" <[email protected]>
To: "Ben Becker" <[email protected]>
Cc: <[email protected]>
Sent: Saturday, December 20, 2003 1:30 AM
Subject: Re: NAT setup

Quoted 49 lines

Hi Ben,

Very interesting concept. There are two major parts to this:

1) Outbound packets from those static IP's to your gateway. this can be done by enabling proxy-arp on your gateway to answer to any arp request. This way the clients would hand over their traffic to your gateway. Subsequently your gateway would SNAT them and throw it on the Internet.

2) Inbound reply packets coming from the outside. This is a bit tricky because, once they're in and de-SNATed, your gateway must know where to send them to. Since your gateway has only one default route and no knowledge about those static IP's behind it, it would automatically send the reply packets back to the Internet. You might overcome this by blindly forwarding these ESTABLISHED incoming packets through your internal interface but you still need to somehow do an ARP for an IP outside your LAN segment. At this point I don't have any simple solution for that. But there are some very sharp ARP people here on the list who could hack something together for you or give you a pointer to an already hacked solution.

Ramin

Quoted 18 lines · Ben Becker

Hello everybody,

I'm trying to figure out a way to set up basic NAT, but with the ability to allow users on the local side to use any static IP configuration. Quick Example: somebody has a static IP configured on their laptop, stays at a hotel with Internet access, and will be able to browse the Internet without changing their IP settings.

My first question is: does anybody know what this feature is called? Second question: Is it possible to do this with netfilter? I'm thinking this would require creating a new virtual interface for each user's configuration to match their gateway (among other things), but I'm hoping netfilter has some magical way of doing this (hoping). If not, does anybody know of any software that can do this?

Regards,
Ben Becker

#3 lore raw
Quoted 3 lines · Søren Kent Jensen

What you need is:
arp -s <Outside IP> <Outside MAC> pub
and a route to the <Outside IP> via the internal interface.

And do you know how he can add these two variables dynamically to his system?

Ramin

Quoted 65 lines

That should do the trick.

Regards
Søren Kent Jensen

----- Original Message -----
From: "Ramin Dousti" <[email protected]>
To: "Ben Becker" <[email protected]>
Cc: <[email protected]>
Sent: Saturday, December 20, 2003 1:30 AM
Subject: Re: NAT setup

Quoted 49 lines

Hi Ben,

Very interesting concept. There are two major parts to this:

1) Outbound packets from those static IP's to your gateway. this can be done by enabling proxy-arp on your gateway to answer to any arp request. This way the clients would hand over their traffic to your gateway. Subsequently your gateway would SNAT them and throw it on the Internet.

2) Inbound reply packets coming from the outside. This is a bit tricky because, once they're in and de-SNATed, your gateway must know where to send them to. Since your gateway has only one default route and no knowledge about those static IP's behind it, it would automatically send the reply packets back to the Internet. You might overcome this by blindly forwarding these ESTABLISHED incoming packets through your internal interface but you still need to somehow do an ARP for an IP outside your LAN segment. At this point I don't have any simple solution for that. But there are some very sharp ARP people here on the list who could hack something together for you or give you a pointer to an already hacked solution.

Ramin

Quoted 18 lines · Ben Becker

Hello everybody,

I'm trying to figure out a way to set up basic NAT, but with the ability to allow users on the local side to use any static IP configuration. Quick Example: somebody has a static IP configured on their laptop, stays at a hotel with Internet access, and will be able to browse the Internet without changing their IP settings.

My first question is: does anybody know what this feature is called? Second question: Is it possible to do this with netfilter? I'm thinking this would require creating a new virtual interface for each user's configuration to match their gateway (among other things), but I'm hoping netfilter has some magical way of doing this (hoping). If not, does anybody know of any software that can do this?

Regards,
Ben Becker