APIC error
CPU1: Intel(R) Pentium(R) 4 CPU 3.20GHz stepping 09 Total of 2 processors activated (12753.30 BogoMIPS). ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map ...changing IO-APIC physical APIC ID to 2 ... ok. init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-20 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 29.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178020 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0020
.... register #02: 00178020
....... : arbitration: 00
An unexpected IO-APIC was found. If this kernel release is less than three months old please report this to [email protected] .... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00 01 003 03 0 0 0 0 0 1 1 39 02 003 03 0 0 0 0 0 1 1 31 03 003 03 0 0 0 0 0 1 1 41 04 003 03 0 0 0 0 0 1 1 49 05 003 03 0 0 0 0 0 1 1 51 06 003 03 0 0 0 0 0 1 1 59 07 003 03 0 0 0 0 0 1 1 61 08 003 03 0 0 0 0 0 1 1 69 09 003 03 1 1 0 0 0 1 1 71 0a 003 03 0 0 0 0 0 1 1 79 0b 003 03 0 0 0 0 0 1 1 81 0c 003 03 0 0 0 0 0 1 1 89 0d 003 03 0 0 0 0 0 1 1 91 0e 003 03 0 0 0 0 0 1 1 99 0f 003 03 0 0 0 0 0 1 1 A1 10 003 03 1 1 0 1 0 1 1 A9 11 003 03 1 1 0 1 0 1 1 B1 12 003 03 1 1 0 1 0 1 1 B9 13 003 03 1 1 0 1 0 1 1 C1 14 000 00 1 0 0 0 0 0 0 00 15 003 03 1 1 0 1 0 1 1 C9 16 003 03 1 1 0 1 0 1 1 D1 17 003 03 1 1 0 1 0 1 1 D9
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23 .................................... done. Using local APIC timer interrupts. calibrating APIC timer ...
..... CPU clock speed is 3191.8903 MHz. ..... host bus clock speed is 199.4931 MHz.
cpu: 0, clocks: 1994931, slice: 664977 CPU0<T0:1994928,T1:1329936,D:15,S:664977,C:1994931>
cpu: 1, clocks: 1994931, slice: 664977 CPU1<T0:1994928,T1:664960,D:14,S:664977,C:1994931> cpu_sibling_map[0] = 1
cpu_sibling_map[1] = 0
mapping CPU#0's runqueue to CPU#1's runqueue.
Please advise. Thanks.
Signature · 1 line
Ed Westphal <[email protected]>