more hamlib and gMFSK problems

Thanks for the earlier help. I think I'm making progress. I think the issue is with the hamlib install, although some of the programs like rigctl run ok. When I ./configure --enable-hamlib | make | make install gMFSK, I get the following:

checking for libgnomeui-2.0 hamlib... Package hamlib was not found in the pkg-config search path.
Perhaps you should add the directory containing `hamlib.pc' to the PKG_CONFIG_PATH environment variable
No package 'hamlib' found

configure: error: Library requirements (libgnomeui-2.0 hamlib) not met; consider adjusting the PKG_CONFIG_PATH environment variable if your libraries are in a nonstandard prefix so pkg-config can find them. --end of quote--

Config without --enable-hamlib gives a good install, but will not install hamlib:

checking PACKAGE_LIBS... -pthread -Wl,--export-dynamic -L/usr/X11R6/lib -lgnomeui-2 -lSM -lICE -lbonoboui-2 -lxml2 -lpthread -lz -lgnomecanvas-2 -lgnome-2 -lpopt -lart_lgpl_2 -lpangoft2-1.0 -lgtk-x11-2.0 -lgdk-x11-2.0 -latk-1.0 -lgdk_pixbuf-2.0 -lpangoxft-1.0 -lpangox-1.0 -lpango-1.0 -lbonobo-2 -lgconf-2 -lgnomevfs-2 -lbonobo-activation -lORBit-2 -lgobject-2.0 -lgthread-2.0 -lm -lgmodule-2.0 -ldl -lglib-2.0
configure: Disabling hamlib support

--end quote--

Apparently my hamlib is not installed correctly. It is in the directory /usr/local/lib with a bunch of rig-specific hamlib files, and a subdirectory called pkgconfig with the files fftw3.pc and hamlib.pc in it. I did see a message in the archives that suggested editing /etc/ld.so.conf to add /usr/local/lib and then running ldconfig, which I did prior to installing gMFSK.

By the way, the behavior is identical in 0.5 and 0.6beta3, if that matters (my deduction is that this indicates a problem with the hamlib install, not gMFSK).

Any ideas on where I'm missing the boat, or what I might do to correct?

de N5NW / NNN0RBB (Marty)
Bellbrook, Ohio

Marty,

You should probably use:

./configure --enable-hamlib && make && make install

instead.

You may have to copy

/usr/local/lib/pkgconfig/hamlib.pc

to

/usr/lib/pkgconfig/hamlib.pc

...or symlink the directories.

Hope this helps.

Wilbert, ZL2BSJ

...

It is installed correctly but in a non-standard place (/usr/local). You have already configured the dynamic linker to look under /usr/local but you have to give pkg-config a hint too. To do that see what "man pkg-config" says about PKG_CONFIG_PATH.

Tomi Manninen / OH2BNS / KP20ME04

Where is the standard installation location, and how do I get hamlib to install there? I think I'd rather try that than to direct each of the apps that use it to the non-standard location.

Thanks,
de N5NW / NNN0RBB (Marty)
Bellbrook, Ohio

-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Tomi Manninen
Sent: Monday, May 03, 2004 10:13 AM
To: Linux-hams List
Subject: Re: more hamlib and gMFSK problems

...

It is installed correctly but in a non-standard place (/usr/local). You have already configured the dynamic linker to look under /usr/local but you have to give pkg-config a hint too. To do that see what "man pkg-config" says about PKG_CONFIG_PATH.

--
Tomi Manninen / OH2BNS / KP20ME04

-
To unsubscribe from this list: send the line "unsubscribe linux-hams" in the body of a message to [email protected] More majordomo info at
http://vger.kernel.org/majordomo-info.html

I had thought I covered this once already in this thread, but perhaps it did not get through o.k.

for hamlib do this :

  ./configure --prefix=/usr

for gmfsk do this (or soemthing similar) :

./configure --prefix=/usr --sysconfdir=/etc --localstatedir=/var\
--enable-hamlib

Between the two make sure you or you package management updates the library confs. by issuing this (generally as root);

ldconfig

Have fun with this;

Vy 73;

Bob
w9ya

I think that you should be able to make hamlib visible to any apps by adding the non-standard location to /etc/ld.so.conf and running ldconfig.

On the other hand, if you are running Debian, it is easier to just run 'apt-get install hamlib2' (thanks Joop!)

Bob, N7XY

Bob Nielsen, N7XY                          n7xy (at) n7xy.net
Bainbridge Island, WA                      http://www.n7xy.net

Hello all,

Anyone know where there is a version of the HAM HOWTO that is less than 7 years old?

Thanks,

Dave
VA3BHF

The HAM HOWTO is obsolete. We now have http://radio.linux.org.au

Joop, PG4I

Hello all,

This may be a dumb question, but I've searched all the docs I can find and don't seem to get anywhere. The FBB documentation mentions INSTALL.SH for setting up initial parameters. I installed FBB using the Debian packages, and I cannot find INSTALL.SH anywhere, nor is it in the file list for the package. The BBS works quite well, as far as accepting NETROM and telnet connections, except that I can't seem to set security levels and actually get SYSOP access. The Documentation mentions that a file called INIT.SYS gets created, but from what I can tell, the /etc/ax25/fbb.conf file seems to have SOME of the contents that are supposed to be in INIT.SYS, and there is no INIT.SYS file.

Am I chasing a wild goose here? Or is there some modification in the Debian-packaged version that makes this unneccesary?

Thanks for your help,

Dave
VA3BHF

You need to run /usr/sbin/fbb. This is actually a shell script, which asks questions and sets up a fbb.conf and port.sys file. Next it runs the actual daemon (xffbd). The script is easy to read, see also 'man fbb'.

Joop PG4I