Simple HTB setup with tcng
Hello all,
I am trying to set up a simple htb based system, where packets with source ip 10.0.0.1 should have their own class.
I plan to use tcng to set it up easier.
Is there something wrong in my tcng file ?
~/tcng$ cat htb
/*
*/
#include "fields.tc"
#include "ports.tc"
dev eth0 {
htb ( ) {
class ( rate 600kbps, ceil 600kbps )
{
class () if ip_src = 10.0.0.1 ;
class (default) ;
}
}
}When I compile it, I get :
~/tcng$ tcc htb
# ================ Device eth0
tc qdisc add dev eth0 handle 1:0 root htb default 3
tc class add dev eth0 parent 1:0 classid 1:1 htb rate 75000bps ceil 75000bps
tc class add dev eth0 parent 1:1 classid 1:2 htb rate 75000bps ceil 75000bps
tc class add dev eth0 parent 1:1 classid 1:3 htb rate 75000bps ceil 75000bps
tc filter add dev eth0 parent 1:1 protocol all prio 1 u32 match u32 0xa000001 0xffffffff at 12 classid 1:2
which is not working as expected.
Packets never get matched. From what I understand of tc (not too much), the filter should have been :
tc filter add dev eth0 parent 1:0 protocol all prio 1 u32 match u32 0xa000001 0xffffffff at 12 classid 1:2
(I replaced parent 1:1 by parent 1:0).
I tried this setup and it works as expected (at least : packets from the server gets matched, other don't. I have used tc -s class show dev eth0 to see it).
Do I miss something ?
Thank you.
Signature · 6 lines
Clement MOREAU <[email protected]> _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
salut clemment
try adapting the following to your needs ... it's been working for me. roughly similar to wondershaper excepting that it is in tcng:
i have a ppp interface on an analog modem so in my firewall i mark packets coming in from this device as following:
iptables --append PREROUTING --table mangle --in-interface ppp0 \
--jump MARK --set-mark 0x7cheers
charles
/*
* tc next generation script by
* charles shick
*/
#define LAN "eth0"
#define LAN_INGRESS 700000
#define LAN_EGRESS 700000
dev LAN {
# ingress {
# $policer = SLB( cir LAN_INGRESS kbps ); # class ( <> ) if SLB_ok( $policer ); # drop if 1;
# }
egress {
class ( <$ppp> ) if meta_nfmark = 0x7;
class ( <$high> ) if ip_proto = IPPROTO_ICMP ||
ip_tos = 0x10 ||
tcp_sport = 80 ||
tcp_sport = 110 ||
udp_sport = 53 ||
tcp_ack;
class ( <$medium> ) if tcp_dport = 25;
class ( <$low> ) if 1;
htb () { class ( rate LAN_EGRESS kbps ) {
$ppp = class ( prio 1, rate 56 kbps )
{ sfq ( perturb 10 sec ); };
$high = class ( prio 1, rate ( 0.5 * LAN_EGRESS )kbps )
{ sfq ( perturb 10 sec ); };
$medium = class (prio 2, rate ( 0.3 * LAN_EGRESS )kbps )
{ sfq ( perturb 10 sec ); };
$low = class (prio 3, rate ( 0.2 * LAN_EGRESS )kbps )
{ sfq ( perturb 10 sec ); };
}
}
}
}Quoted 51 lines · Clement MOREAU
Hello all,
I am trying to set up a simple htb based system, where packets with source ip 10.0.0.1 should have their own class.
I plan to use tcng to set it up easier.Is there something wrong in my tcng file ?
~/tcng$ cat htb
/*
*/#include "fields.tc"
#include "ports.tc"dev eth0 { htb ( ) { class ( rate 600kbps, ceil 600kbps ) { class () if ip_src = 10.0.0.1 ; class (default) ; } } }When I compile it, I get :
~/tcng$ tcc htb
# ================ Device eth0
tc qdisc add dev eth0 handle 1:0 root htb default 3
tc class add dev eth0 parent 1:0 classid 1:1 htb rate 75000bps ceil 75000bps
tc class add dev eth0 parent 1:1 classid 1:2 htb rate 75000bps ceil 75000bps
tc class add dev eth0 parent 1:1 classid 1:3 htb rate 75000bps ceil 75000bps
tc filter add dev eth0 parent 1:1 protocol all prio 1 u32 match u320xa0000010xffffffffat 12 classid 1:2which is not working as expected.
Packets never get matched. From what I understand of tc (not too much), the filter should have been :
tc filter add dev eth0 parent 1:0 protocol all prio 1 u32 match u320xa0000010xffffffffat 12 classid 1:2(I replaced parent 1:1 by parent 1:0).
Quoted 7 lines
I tried this setup and it works as expected (at least : packets from the server gets matched, other don't. I have used tc -s class show dev eth0 to see it).
Do I miss something ?
Thank you.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Thank you for your help.
this setup is creating an additionnal qdisc (dsmark). For performance reasons, I would prefer using filters directly attached to htb qdisc. I think it is possible, at least it seems to be possible with tc (not tcng).
It seems to me that tcc is doing something wrong with htb and indexes, do I miss something ?
Thank you.
Quoted 131 lines · Le mer 05/05/2004 à 09:59, [email protected] a écrit :
salut clemment
try adapting the following to your needs ... it's been working for me. roughly similar to wondershaper excepting that it is in tcng:
i have a ppp interface on an analog modem so in my firewall i mark packets coming in from this device as following:
iptables --append PREROUTING --table mangle --in-interface ppp0 \ --jump MARK --set-mark 0x7cheers
charles
/*
* tc next generation script by
* charles shick
*/#define LAN "eth0"
#defineLAN_INGRESS700000
#defineLAN_EGRESS700000dev LAN {
# ingress {
# $policer = SLB( cir LAN_INGRESS kbps ); # class ( <> ) if SLB_ok( $policer ); # drop if 1;# }
egress { class ( <$ppp> ) if meta_nfmark = 0x7; class ( <$high> ) if ip_proto = IPPROTO_ICMP || ip_tos = 0x10 || tcp_sport = 80 || tcp_sport = 110 || udp_sport = 53 || tcp_ack; class ( <$medium> ) if tcp_dport = 25; class ( <$low> ) if 1; htb () { class ( rate LAN_EGRESS kbps ) { $ppp = class ( prio 1, rate 56 kbps ) { sfq ( perturb 10 sec ); }; $high = class ( prio 1, rate ( 0.5 * LAN_EGRESS )kbps ) { sfq ( perturb 10 sec ); }; $medium = class (prio 2, rate ( 0.3 * LAN_EGRESS )kbps ) { sfq ( perturb 10 sec ); }; $low = class (prio 3, rate ( 0.2 * LAN_EGRESS )kbps ) { sfq ( perturb 10 sec ); }; } } } }Quoted 51 lines · Clement MOREAU
Hello all,
I am trying to set up a simple htb based system, where packets with source ip 10.0.0.1 should have their own class.
I plan to use tcng to set it up easier.Is there something wrong in my tcng file ?
~/tcng$ cat htb
/*
*/#include "fields.tc"
#include "ports.tc"dev eth0 { htb ( ) { class ( rate 600kbps, ceil 600kbps ) { class () if ip_src = 10.0.0.1 ; class (default) ; } } }When I compile it, I get :
~/tcng$ tcc htb
# ================ Device eth0
tc qdisc add dev eth0 handle 1:0 root htb default 3
tc class add dev eth0 parent 1:0 classid 1:1 htb rate 75000bps ceil 75000bps
tc class add dev eth0 parent 1:1 classid 1:2 htb rate 75000bps ceil 75000bps
tc class add dev eth0 parent 1:1 classid 1:3 htb rate 75000bps ceil 75000bps
tc filter add dev eth0 parent 1:1 protocol all prio 1 u32 match u320xa0000010xffffffffat 12 classid 1:2which is not working as expected.
Packets never get matched. From what I understand of tc (not too much), the filter should have been :
tc filter add dev eth0 parent 1:0 protocol all prio 1 u32 match u320xa0000010xffffffffat 12 classid 1:2(I replaced parent 1:1 by parent 1:0).
Quoted 7 lines
I tried this setup and it works as expected (at least : packets from the server gets matched, other don't. I have used tc -s class show dev eth0 to see it).
Do I miss something ?
Thank you.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
Signature · 27 lines
Clement MOREAU <[email protected]> Inventel -- http://www.inventel.fr **************************************************************************** Ce message et ses pieces jointes contiennent des informations confidentielles. Il est etabli a l'intention exclusive de ses destinataires. Si vous n'en etes pas destinataire, merci de le detruire et d'en avertir immediatement l'expediteur. L'integrite de ce message ne pouvant etre garantie sur Internet, Inventel ne peut etre tenue responsable de son contenu. This e-mail and its attachments are confidential and intended solely for the addressees. If you are not the intended recipient of this message, then please delete it and notify the sender. Since the integrity of this message cannot be guaranteed on the Internet, Inventel cannot therefore be considered responsible for its content. **************************************************************************** _______________________________________________ LARTC mailing list / [email protected] http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
salut clemment,
well, i see better now -- you could try something like:
#include "fields.tc"
#include "ports.tc"
dev eth0 {
htb () {
class ( rate 600kbps, ceil 600kbps ) if ip_src = 10.0.0.1;
}
}cheers
charles
Quoted 9 lines · Clement MOREAU
Thank you for your help.
this setup is creating an additionnal qdisc (dsmark). For performance reasons, I would prefer using filters directly attached to htb qdisc. I think it is possible, at least it seems to be possible with tc (not tcng).
It seems to me that tcc is doing something wrong with htb and indexes, do I miss something ?
Quoted 134 lines
Thank you.
Quoted 131 lines · Le mer 05/05/2004 à 09:59, [email protected] a écrit :
salut clemment
try adapting the following to your needs ... it's been working for me. roughly similar to wondershaper excepting that it is in tcng:
i have a ppp interface on an analog modem so in my firewall i mark packets coming in from this device as following:
iptables --append PREROUTING --table mangle --in-interface ppp0 \ --jump MARK --set-mark 0x7cheers
charles
/*
* tc next generation script by
* charles shick
*/#define LAN "eth0"
#defineLAN_INGRESS700000
#defineLAN_EGRESS700000dev LAN {
# ingress {
# $policer = SLB( cir LAN_INGRESS kbps ); # class ( <> ) if SLB_ok( $policer ); # drop if 1;# }
egress { class ( <$ppp> ) if meta_nfmark = 0x7; class ( <$high> ) if ip_proto = IPPROTO_ICMP || ip_tos = 0x10 || tcp_sport = 80 || tcp_sport = 110 || udp_sport = 53 || tcp_ack; class ( <$medium> ) if tcp_dport = 25; class ( <$low> ) if 1; htb () { class ( rate LAN_EGRESS kbps ) { $ppp = class ( prio 1, rate 56 kbps ) { sfq ( perturb 10 sec ); }; $high = class ( prio 1, rate ( 0.5 * LAN_EGRESS )kbps ) { sfq ( perturb 10 sec ); }; $medium = class (prio 2, rate ( 0.3 * LAN_EGRESS )kbps ) { sfq ( perturb 10 sec ); }; $low = class (prio 3, rate ( 0.2 * LAN_EGRESS )kbps ) { sfq ( perturb 10 sec ); }; } } } }Quoted 51 lines · Clement MOREAU
Hello all,
I am trying to set up a simple htb based system, where packets with source ip 10.0.0.1 should have their own class.
I plan to use tcng to set it up easier.Is there something wrong in my tcng file ?
~/tcng$ cat htb
/*
*/#include "fields.tc"
#include "ports.tc"dev eth0 { htb ( ) { class ( rate 600kbps, ceil 600kbps ) { class () if ip_src = 10.0.0.1 ; class (default) ; } } }When I compile it, I get :
~/tcng$ tcc htb
# ================ Device eth0
tc qdisc add dev eth0 handle 1:0 root htb default 3
tc class add dev eth0 parent 1:0 classid 1:1 htb rate 75000bps ceil 75000bps
tc class add dev eth0 parent 1:1 classid 1:2 htb rate 75000bps ceil 75000bps
tc class add dev eth0 parent 1:1 classid 1:3 htb rate 75000bps ceil 75000bps
tc filter add dev eth0 parent 1:1 protocol all prio 1 u32 match u320xa0000010xffffffffat 12 classid 1:2which is not working as expected.
Packets never get matched. From what I understand of tc (not too much), the filter should have been :
tc filter add dev eth0 parent 1:0 protocol all prio 1 u32 match u320xa0000010xffffffffat 12 classid 1:2(I replaced parent 1:1 by parent 1:0).
Quoted 7 lines
I tried this setup and it works as expected (at least : packets from the server gets matched, other don't. I have used tc -s class show dev eth0 to see it).
Do I miss something ?
Thank you.
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/