Skip to contentSkip to conversation

2.6 kernel OOPs with Nomad MuVo MP3 player

DISCUSSION Derek Witt 1 participant 3 messages May 29, 2004 – Jun 1, 2004

lore
Share & tools
lore

Derek Witt

author
#0 lore raw

Good morning.

I am attempting to mount my Creative Nomad MuVo MP3 Player. However, every time I try to mount or copy to the drive, I constantly get a Kernel oops. I am currently running 2.6.6-rc1 under Gentoo 1.4. SuSE 9.0 running vanilla 2.6.5 returns the same problem.

My dump indicates a problem with usb-storage trying to preempt parts of itself.

The included dump is during a copy attempt.

I am quite puzzled by this.. I'm going to rebuild my kernel sans preempt and see what happens.

Here's my information below.

cat /proc/bus/usb/devices (for my Nomad):

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=041e ProdID=4106 Rev= 0.01
S:  Manufacturer=Creative Tech
S:  Product=NOMAD MuVo
S:  SerialNumber=000000000000
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage
E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms

cat /proc/ioports:

0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03e8-03ef : serial
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
5000-500f : 0000:00:07.4
6000-607f : 0000:00:07.4
d000-d00f : 0000:00:07.1
d400-d41f : 0000:00:07.2
d400-d41f : uhci_hcd
d800-d81f : 0000:00:07.3
d800-d81f : uhci_hcd
dc00-dc1f : 0000:00:0a.0
dc00-dc1f : EMU10K1
e000-e007 : 0000:00:0a.1
e400-e4ff : 0000:00:0b.0
e400-e4ff : 8139too

cat /proc/interrupts:

CPU0

  0:   89597648          XT-PIC  timer
  1:      26427          XT-PIC  i8042
  2:          0          XT-PIC  cascade
  3:     436611          XT-PIC  EMU10K1
  4:          0          XT-PIC  acpi
  8:          2          XT-PIC  rtc
 10:    6019061          XT-PIC  nvidia
 11:    1906902          XT-PIC  uhci_hcd, uhci_hcd, eth0
 12:     229068          XT-PIC  i8042
 14:     240778          XT-PIC  ide0
 15:         38          XT-PIC  ide1
NMI:          0
LOC:   89597802
ERR:        184
MIS:          0

lspci:

00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-

        Latency: 8
        Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW-

Rate=x2
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d0000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc.
VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev
40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 4
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Derek J Witt,
[email protected].

FAT: Directory bread(block 494) failed

Unable to handle kernel NULL pointer dereference at virtual address 00000164
 printing eip:
c027e8bc
*pde = 00000000
Oops: 0000 [#1]
PREEMPT
CPU:    0
EIP:    0060:[<c027e8bc>]    Tainted: P
EFLAGS: 00210803   (2.6.6-rc1)

EIP is at as_find_arq_hash+0x2c/0xb0
eax: 00000164 ebx: 00000000 ecx: cbcf52a0 edx: 00000004
esi: cbcf52a0 edi: 000001ef ebp: 00000000 esp: d1f97b50
ds: 007b es: 007b ss: 0068
Process cp (pid: 12777, threadinfo=d1f96000 task=cdbf05f0)

Stack: c011888a d1f97c64 00000164 00000000 cbcf52a0 000001f0 00000000 c028071d
       cbcf52a0 000001ef 00000000 c468aca0 c468aca0 cbcf52a0 00000000 c5664000
       00000000 00000000 c02778a9 c5664000 d1f97bd0 c468a3a0 c027ac78 c5664000
Call Trace:
 [<c011888a>] __wake_up_common+0x3a/0x60
 [<c028071d>] as_merge+0x11d/0x200
 [<c02778a9>] elv_merge+0x29/0x30
 [<c027ac78>] __make_request+0x368/0x5c0
 [<c027b03e>] generic_make_request+0x16e/0x1f0
 [<c0119b30>] autoremove_wake_function+0x0/0x50
 [<c027b11d>] submit_bio+0x5d/0x100
 [<c01561d0>] submit_bh+0xa0/0x200
 [<c0153de9>] __bread_slow+0x59/0xb0
 [<c015416e>] __bread+0x3e/0x50
 [<c01e0356>] fat__get_entry+0xb6/0x194
 [<c01dd3bc>] fat_get_short_entry+0xac/0xb0
 [<c01dd58c>] fat_scan+0x5c/0x94
 [<c01e1d2b>] vfat_find_form+0x3b/0x60
 [<c01e2143>] vfat_create_shortname+0x3f3/0x790
 [<c0138e34>] __alloc_pages+0xa4/0x320
 [<c01e2860>] vfat_build_slots+0x150/0x2f0
 [<c01e2a80>] vfat_add_entry+0x80/0x280
 [<c016993a>] d_splice_alias+0x4a/0x110
 [<c01e3023>] vfat_create+0x63/0x180
 [<c0169649>] d_alloc+0x199/0x1d0
 [<c015f02f>] permission+0x2f/0x50
 [<c01605b9>] vfs_create+0x79/0xd0
 [<c0160baf>] open_namei+0x3bf/0x410
 [<c0150393>] filp_open+0x43/0x70
 [<c015086b>] sys_open+0x5b/0x90
 [<c01061ab>] syscall_call+0x7/0xb

Code: 8b 30 39 c6 74 40 8d b4 26 00 00 00 00 8d bc 27 00 00 00 00
 <6>note: cp[12777] exited with preempt_count 2
bad: scheduling while atomic!
Call Trace:
 [<c0383687>] schedule+0x5a7/0x5b0
 [<c0141aeb>] zap_pmd_range+0x4b/0x70
 [<c0141b5b>] unmap_page_range+0x4b/0x80
 [<c0141d6d>] unmap_vmas+0x1dd/0x240
 [<c0145d70>] exit_mmap+0x80/0x1a0
 [<c0119e35>] mmput+0x65/0x90
 [<c011e277>] do_exit+0x167/0x3f0
 [<c01072ac>] die+0xfc/0x100
 [<c0116e89>] do_page_fault+0x1f9/0x519
 [<c0117df3>] try_to_wake_up+0xa3/0x160
 [<c0117df3>] try_to_wake_up+0xa3/0x160
 [<c0123eb0>] run_timer_softirq+0x110/0x1b0
 [<c011888a>] __wake_up_common+0x3a/0x60
 [<c0118932>] __wake_up_locked+0x22/0x30
 [<c0105101>] __down_trylock+0x51/0x70
 [<c0137a31>] mempool_alloc+0x91/0x190
 [<c0116c90>] do_page_fault+0x0/0x519
 [<c0106bd5>] error_code+0x2d/0x38
 [<c011007b>] mtrr_close+0x1b/0x90
 [<c027e8bc>] as_find_arq_hash+0x2c/0xb0
 [<c011888a>] __wake_up_common+0x3a/0x60
 [<c028071d>] as_merge+0x11d/0x200
 [<c02778a9>] elv_merge+0x29/0x30
 [<c027ac78>] __make_request+0x368/0x5c0
 [<c027b03e>] generic_make_request+0x16e/0x1f0
 [<c0119b30>] autoremove_wake_function+0x0/0x50
 [<c027b11d>] submit_bio+0x5d/0x100
 [<c01561d0>] submit_bh+0xa0/0x200
 [<c0153de9>] __bread_slow+0x59/0xb0
 [<c015416e>] __bread+0x3e/0x50
 [<c01e0356>] fat__get_entry+0xb6/0x194
 [<c01dd3bc>] fat_get_short_entry+0xac/0xb0
 [<c01dd58c>] fat_scan+0x5c/0x94
 [<c01e1d2b>] vfat_find_form+0x3b/0x60
 [<c01e2143>] vfat_create_shortname+0x3f3/0x790
 [<c0138e34>] __alloc_pages+0xa4/0x320
 [<c01e2860>] vfat_build_slots+0x150/0x2f0
 [<c01e2a80>] vfat_add_entry+0x80/0x280
 [<c016993a>] d_splice_alias+0x4a/0x110
 [<c01e3023>] vfat_create+0x63/0x180
 [<c0169649>] d_alloc+0x199/0x1d0
 [<c015f02f>] permission+0x2f/0x50
 [<c01605b9>] vfs_create+0x79/0xd0
 [<c0160baf>] open_namei+0x3bf/0x410
 [<c0150393>] filp_open+0x43/0x70
 [<c015086b>] sys_open+0x5b/0x90
 [<c01061ab>] syscall_call+0x7/0xb
author
#1 lore raw

I have rebuilt my kernel without preempt support and passed "elevator=deadline" to the kernel on reboot. I now can mount my nomad muvo without any major problems.

However, it times out and gives the oops on attemptng to dismount, but the only effect of that is that the USB reiterates itself and the next time I insert the drive, it gets bumped up (e.g. from /dev/sda1 to /dev/sdb1). Also, it sometimes gets rendered read-only (easily resolved by remounting the drive with same device name).

But, during the copy process, my computer is unsually bogged down (the jumping mouse cursor in X).

So, I am suspecting the AS Anticipatory IO scheduler at fault.

Quoted 7 lines · Derek Witt

Good morning.

I am attempting to mount my Creative Nomad MuVo MP3 Player. However, every time I try to mount or copy to the drive, I constantly get a Kernel oops. I am currently running 2.6.6-rc1 under Gentoo 1.4. SuSE 9.0 running vanilla 2.6.5 returns the same problem.

Quoted 8 lines

My dump indicates a problem with usb-storage trying to preempt parts of itself.

The included dump is during a copy attempt.

I am quite puzzled by this.. I'm going to rebuild my kernel sans preempt and see what happens.

Derek J Witt,
[email protected].

author
#2 lore raw
In reply to Derek Witt

Good morning all. I have noticed that my issue's already been resolved. I upgraded to 2.6.7-rc2-bk1 and it works like a charm (with preempt and deadline enabled). It no longer times out or is rendered read only. :)

Quoted 194 lines · Derek Witt

Good morning.

I am attempting to mount my Creative Nomad MuVo MP3 Player. However, every time I try to mount or copy to the drive, I constantly get a Kernel oops. I am currently running 2.6.6-rc1 under Gentoo 1.4. SuSE 9.0 running vanilla 2.6.5 returns the same problem.

My dump indicates a problem with usb-storage trying to preempt parts of itself.

The included dump is during a copy attempt.

I am quite puzzled by this.. I'm going to rebuild my kernel sans preempt and see what happens.

Here's my information below.

cat /proc/bus/usb/devices (for my Nomad):

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#=  4 Spd=12  MxCh= 0
D:  Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=041e ProdID=4106 Rev= 0.01
S:  Manufacturer=Creative Tech
S:  Product=NOMAD MuVo
S:  SerialNumber=000000000000
C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=100mA
I:  If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50
Driver=usb-storage
E:  Ad=04(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=81(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms

cat /proc/ioports:

0000-001f : dma1
0020-0021 : pic1
0040-005f : timer
0060-006f : keyboard
0070-0077 : rtc
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : ide1
01f0-01f7 : ide0
0376-0376 : ide1
0378-037a : parport0
03c0-03df : vga+
03e8-03ef : serial
03f6-03f6 : ide0
0cf8-0cff : PCI conf1
5000-500f : 0000:00:07.4
6000-607f : 0000:00:07.4
d000-d00f : 0000:00:07.1
d400-d41f : 0000:00:07.2
d400-d41f : uhci_hcd
d800-d81f : 0000:00:07.3
d800-d81f : uhci_hcd
dc00-dc1f : 0000:00:0a.0
dc00-dc1f : EMU10K1
e000-e007 : 0000:00:0a.1
e400-e4ff : 0000:00:0b.0
e400-e4ff : 8139too

cat /proc/interrupts:

CPU0

  0:   89597648          XT-PIC  timer
  1:      26427          XT-PIC  i8042
  2:          0          XT-PIC  cascade
  3:     436611          XT-PIC  EMU10K1
  4:          0          XT-PIC  acpi
  8:          2          XT-PIC  rtc
 10:    6019061          XT-PIC  nvidia
 11:    1906902          XT-PIC  uhci_hcd, uhci_hcd, eth0
 12:     229068          XT-PIC  i8042
 14:     240778          XT-PIC  ide0
 15:         38          XT-PIC  ide1
NMI:          0
LOC:   89597802
ERR:        184
MIS:          0

lspci:

00:00.0 Host bridge: VIA Technologies, Inc. VT82C693A/694x [Apollo PRO133x] (rev c4)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-

        Latency: 8
        Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
        Capabilities: [a0] AGP version 2.0
                Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW+ AGP3- Rate=x1,x2
                Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP+ GART64- 64bit- FW-

Rate=x2
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:01.0 PCI bridge: VIA Technologies, Inc. VT82C598/694x [Apollo MVP3/Pro133x AGP] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 0000f000-00000fff
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d0000000-d7ffffff
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: VIA Technologies, Inc.
VT82C586/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Region 4: I/O ports at d000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.2 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at d400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.3 USB Controller: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (rev 16) (prog-if 00 [UHCI])
Subsystem: VIA Technologies, Inc. (Wrong ID) USB Controller
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Latency: 32, cache line size 08
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at d800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev
40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin ? routed to IRQ 4
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Quoted 1 line

Derek J Witt,

[email protected].
Derek J Witt,
[email protected].