Skip to contentSkip to conversation

Prism 2.5 MiniPCI Wireless Unstable

DISCUSSION Michael B Allen 1 participant 2 messages Jul 11, 2005 – Jul 12, 2005 3 messages not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): 1108.192.168.0.150.1121089967.squirrel@kone

A message that is not in the archive (sent off-list or not yet received): 1118.192.168.0.150.1121090918.squirrel@kone

#2 lore raw
Quoted 8 lines · On Mon, 11 Jul 2005 17:08:38 +0300 (EEST) "Jar" <[email protected]> wrote:
Quoted 7 lines

FYI:

Please use more suitable driver for 802.11b Prism cards. This kind of driver is hostap_pci (for PCI cards). It can be downloaded from http://hostap.epitest.fi/

This driver really works for Prism2/2.5/3 cards!

Quoted 8 lines

Sorry about this spam, I didn't read your mail in LKML properly. You already have used hostap in the past :)

Still I think the hostap_pci is the best driver for Prism2/2.5/3 cards. I have one Prism2.5 PCI card in daily & heavy use as access point. The card becomes 100% stable after I updated it's primary and station firmawares (PRI 1.0.0 --> 1.1.1, STA 1.4.9-->1.7.4). There have been a lot of development after 2.4 days in hostap driver. I use the latest and greatest 0.3.9 version :)

Better. With the hostap_pci driver, after 2 and a half tries, I managed to get the backup to complete. But I still get lots of errors along the way:

Jul 11 16:29:42 quark kernel: NETDEV WATCHDOG: wifi0: transmit timed out
Jul 11 16:29:42 quark kernel: wifi0 Tx timed out! Resetting card
Jul 11 16:29:43 quark kernel: hostap_pci: wifi0: resetting card
Jul 11 16:30:13 quark last message repeated 2 times
Jul 11 16:30:28 quark kernel: NETDEV WATCHDOG: wifi0: transmit timed out
Jul 11 16:30:28 quark kernel: wifi0 Tx timed out! Resetting card
Jul 11 16:30:29 quark kernel: hostap_pci: wifi0: resetting card
Jul 11 16:31:03 quark last message repeated 2 times
Jul 11 16:31:18 quark kernel: NETDEV WATCHDOG: wifi0: transmit timed out
Jul 11 16:31:18 quark kernel: wifi0 Tx timed out! Resetting card
Jul 11 16:31:19 quark kernel: hostap_pci: wifi0: resetting card

...

With the hostap_pci driver, the first time I tried to run the backup (rsync over ssh from workstation next to AP to T30 w/ prism card) my machine locked up after about 15 minutes. After rebooting, running fsck, and moving close to the AP I stopped X and tried to run it on virtual consoles. After about 15 minutes it stopped but the machine didn't lockup. It was totally idle w/ no network traffic. Running lsof | grep rsync tool about 20 seconds to respond. After stopping the interface and reloading the hostap_pci modules I was able to get network back. Interestingly rsync suddenly resumed where it left off and eventually completed (resetting the card all the way). Something about this rsync backup really tickles the system.

Is this a known problem? Is it known to be the driver, firmware, or what? Could it be my access point (Linksys 802.11b 4 port switch BEFW11S4 v.2)?

Thanks for your help. Personally I think I'm ok - now that I've sync'd up the backup should only take a minute or two now. But I'm willing to explore this if someone wants me to try some debugging.

Quoted 15 lines

See..

hostap_pci: 0.3.9 - 2005-06-10 (Jouni Malinen <[email protected]>)
PCI: Found IRQ 9 for device 0000:00:09.0
hostap_pci: Registered netdevice wifi1
wifi1: Original COR value: 0x0
prism2_hw_init: initialized in 195 ms
wifi1: NIC: id=0x8013 v1.0.0
wifi1: PRI: id=0x15 v1.1.1
wifi1: STA: id=0x1f v1.7.4
wifi1: Intersil Prism2.5 PCI: mem=0xe7800000, irq=9
wifi1: registered netdevice wlan1
wifi1: Deauthenticate all stations
wifi1: prism2_send_mgmt - device is not UP - cannot send frame
wlan1: Enabling ALC

hostap_pci: 0.3.9 - 2005-06-10 (Jouni Malinen <[email protected]>)
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11
hostap_pci: Registered netdevice wifi0
wifi0: NIC: id=0x8013 v1.0.0
wifi0: PRI: id=0x15 v1.1.0
wifi0: STA: id=0x1f v1.4.9
wifi0: Intersil Prism2.5 PCI: mem=0xf8000000, irq=11

Mike

A message that is not in the archive (sent off-list or not yet received): [email protected]

#4 lore raw

My Thinkpad T30 "Intel" wireless now works perfectly after switching to the hostap_pci driver and updating the primary and station firmware (pk010101.hex and sf010804.hex respectively) on the MiniPCI card using the WinUpdate program (I dual boot Win2K) as described in the below link.

I re-ran my rsync test and it completed without error at a smooth 550Kbps from two floors up.

Thanks,
Mike

hostap_pci: Registered netdevice wifi0
wifi0: NIC: id=0x8013 v1.0.0
wifi0: PRI: id=0x15 v1.1.1
wifi0: STA: id=0x1f v1.8.4
wifi0: Intersil Prism2.5 PCI: mem=0xf8000000, irq=11

Quoted 44 lines · On Tue, 12 Jul 2005 01:46:52 +0300 Jar <[email protected]> wrote:
Quoted 7 lines · Michael B Allen

hostap_pci: 0.3.9 - 2005-06-10 (Jouni Malinen <[email protected]>)
ACPI: PCI interrupt 0000:02:02.0[A] -> GSI 11 (level, low) -> IRQ 11
hostap_pci: Registered netdevice wifi0
wifi0: NIC: id=0x8013 v1.0.0
wifi0: PRI: id=0x15 v1.1.0
wifi0: STA: id=0x1f v1.4.9
wifi0: Intersil Prism2.5 PCI: mem=0xf8000000, irq=11

Maybe you should try to update the firmwares, that is all you can do at this point. For me the 1.1.1/1.7.4 combination has been worked like a charm, also when used in heavy load. I belive the driver itself is stable (the PCI prism2.5 card never timed out for me). So there has to be hardware/firmware problem somewhere.

PRI: id=0x15 v1.1.0 --> v1.1.1
STA: id=0x1f v1.4.9 --> v1.7.4

The Flashing HOWTO: http://linux.junsun.net/intersil-prism/
The firmware collection: http://www.red-bean.com/~proski/firmware/

You can try the RAM (volatile) firmawares first and if it helps you can flash the non volatile versions (Flash) if you want. Newer flash primary firmware alone, but primary and station firmwares simultaneously. The filenames (if I remember correctly) are:

ak010104.hex (RAM PRI:1.1.4)
rf010704.hex (RAM STA:1.7.4)

pk010101.hex (Flash PRI:1.1.1)
sf010704.hex (Flash STA:1.7.4)

There is also newer verisons available:

The latest firmwares in the collection are:

RAM Flash

Prism 2      PCMCIA         1.7.1         1.7.1
Prism 2.5/3  PCI/PCMCIA     1.8.4 (NEW!)  1.8.4
Prism 3      USB            1.8.3         1.8.4
Signature · 1 line
Best Regards, Jar