Problem mounting dvd if the drive spin down
Hello guys, this is my first post in this list, I'm not a subscriner so please CC me for reply and comments. Thank you.
I've got an Acer Aspire 1601LC laptop and I get strange issue when mounting dvd (I cannot say the time 'cause firstly I thought to bad dvd).
If I close the try and then mount the dvd everything is ok, but if the drive stops, for example if I insert the dvd and go on with reading my mail and try to access again the dvd this hangs up.
The drive is a Matshita as dmesg say:
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Example:
I put the dvd into the drive, wait some time... the drive spin down
$ mount /mnt/cdrom
I got this in /var/log/messages
Apr 2 18:11:58 maggot kernel: hdc: DMA disabled
and dmesg:
hdc: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hdc: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
I'm using 2.6.11 kernel, but 2.6.10 wasn't better. I notice that if I run
$ hdparm -Y /dec/hdc
output:/dev/hdc:
issuing sleep command
HDIO_DRIVE_CMD(sleep) failed: Input/output error
the drive seems to wake up and I can run mount without problems.
This is the output from hdparm -i:/dev/hdc:
Model=UJDA740 DVD/CDRW, FwRev=1.00, SerialNo= Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic } RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=unknown, BuffSize=512kB, MaxMultSect=0 (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0 IORDY=yes, tPIO={min:180,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 *udma2
AdvancedPM=no
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 3:
* signifies the current active mode
Is there any solution to this problem?
Thank in advance, and go on this way.
Quoted 11 lines · Nate Grey
Hello guys, this is my first post in this list, I'm not a subscriner so please CC me for reply and comments. Thank you.
I've got an Acer Aspire 1601LC laptop and I get strange issue when mounting dvd (I cannot say the time 'cause firstly I thought to bad dvd).
If I close the try and then mount the dvd everything is ok, but if the drive stops, for example if I insert the dvd and go on with reading my mail and try to access again the dvd this hangs up.
Did it work OK under any other kernel versions? If so, which?
Quoted 55 lines
The drive is a Matshita as dmesg say:
hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33)
Example:
I put the dvd into the drive, wait some time... the drive spin down$ mount /mnt/cdromI got this in
/var/log/messagesApr 2 18:11:58 maggot kernel: hdc: DMA disabledand dmesg:
hdc:cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hdc:cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknownI'm using 2.6.11 kernel, but 2.6.10 wasn't better. I notice that if I run
$ hdparm -Y /dec/hdcoutput:/dev/hdc:
issuing sleep command
HDIO_DRIVE_CMD(sleep)failed: Input/output errorthe drive seems to wake up and I can run mount without problems.
This is the output from hdparm -i:/dev/hdc:
Model=UJDA740 DVD/CDRW, FwRev=1.00, SerialNo= Config={ Fixed Removeable DTR<=5Mbs DTR>10Mbs nonMagnetic } RawCHS=0/0/0, TrkSize=0, SectSize=0, ECCbytes=0 BuffType=unknown, BuffSize=512kB, MaxMultSect=0 (maybe): CurCHS=0/0/0, CurSects=0, LBA=yes, LBAsects=0 IORDY=yes, tPIO={min:180,w/IORDY:120}, tDMA={min:120,rec:120} PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: sdma0 sdma1 sdma2 mdma0 mdma1 mdma2 UDMA modes: udma0 udma1 *udma2
AdvancedPM=no
Drive conforms to: ATA/ATAPI-5 T13 1321D revision 3:* signifies the current active mode
Is there any solution to this problem?
Thank in advance, and go on this way.
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Quoted 1 line · Andrew Morton
Did it work OK under any other kernel versions? If so, which?
At least it works in 2.6.7, I jump from .7 to .9 then .10 and finally .11, I notice this problem in 2.6.10 firstly.
If you need addictional info about the drive just ask.
I forgot to say that at boot time hdparm is run on the device:
hdparm -c1 -d1 -u1 -X66 /dev/hdc
Thank you.
P.S.
hdc: cdrom_decode_status: status=0x51 { DriveReady SeekComplete Error }
hdc: cdrom_decode_status: error=0x40 { LastFailedSense=0x04 }
ide: failed opcode was: unknown
hdc: ide_intr: huh? expected NULL handler on exit
hdc: ATAPI reset completeend_request: I/O error, dev hdc, sector 64isofs_fill_super: bread failed, dev=hdc, iso_blknum=16, block=16
Quoted 1 line
At least it works in 2.6.7
I correct myself, I try 2.6.7 kernel and I got the same problem...
Is it the drive itself going down?
( The drive seems to work without problem on Windows XP )
Thank you.
P.S.
Please Cc: me and sorry for my English.
Bye Bye