Skip to contentSkip to conversation

kbtab tweaks, pen tool reporting

PATCH New Dave Ahlswede 1 participant 1 message May 5, 2005

lore
Share & tools
lore
#0 lore raw

PATCH 1/1 kbtab tweaks, pen tool reporting

This patch improves the kbtab behavior with regards to the pen tool a little bit. I previously submitted a patch with the rather bad behavior of reporting the pen tool as not-in-use when the device was opened, but I've changed it around a little this time.

With this patch, the driver will report the pen tool as not-in-use if it hasn't received input events for over a second-- given the somewhat sloppy hardware, this seems to be the only way to get a sensible value here. I hope this is acceptable.

There's also a few minor tweaks in the last block. I've turned off fuzz compensation for the X and Y axes, as I found that these actually made the jitter seem worse when drawing, causing sudden pixel-sized jumps instead of the more gradual usually-subpixel jumps without the jitter.

Conversely, some small fuzz compensation seems good on the pressure axis to help prevent stray click-and-release under low pressure.

Finally, as before, I've corrected the pressure limit to 127 instead of 255 (The upper limit as observed on two KBGear tablets)

Please CC me on any replies; I'm not subscribed to lkml. Thanks much!

Patch against 2.6.11.7 (seems to apply to .12-rc3 too) follows:

--- ../../../../linux-2.6.11.7/drivers/usb/input/kbtab.c 2005-04-07 14:57:08.000000000 -0400
+++ linux/drivers/usb/input/kbtab.c 2005-05-05 02:57:13.000000000 -0400 @@ -1,3 +1,4 @@
+#include <linux/jiffies.h>
#include <linux/kernel.h>
#include <linux/slab.h>
#include <linux/input.h>
@@ -13,6 +14,9 @@
* v0.0.2 - Updated, works with 2.5.62 and 2.4.20;
* - added pressure-threshold modules param code from
* Alex Perry <[email protected]>
+ * - Report pen tool not in use after ~1 second idle
+ * Tweak jitter and max pressure limit
+ * Dave Ahlswede <[email protected]>
*/

#define DRIVER_VERSION "v0.0.2"
@@ -25,6 +29,7 @@
MODULE_LICENSE(DRIVER_LICENSE);

#define USB_VENDOR_ID_KBGEAR 0x084e
+#define KBTAB_PEN_TIMEOUT_DELAY 1000

static int kb_pressure_click = 0x10;
module_param(kb_pressure_click, int, 0);
@@ -40,6 +45,7 @@
int x, y;
int button;
int pressure;
+ unsigned long pen_timeout;
__u32 serial[2];
char phys[32];
};
@@ -71,7 +77,11 @@

kbtab->pressure = (data[5]);

- input_report_key(dev, BTN_TOOL_PEN, 1);
+ if (time_after(jiffies, kbtab->pen_timeout))
+ input_report_key(dev, BTN_TOOL_PEN, 0);
+ else
+ input_report_key(dev, BTN_TOOL_PEN, 1);
+ kbtab->pen_timeout = jiffies + KBTAB_PEN_TIMEOUT_DELAY;

input_report_abs(dev, ABS_X, kbtab->x);
input_report_abs(dev, ABS_Y, kbtab->y);
@@ -160,10 +170,11 @@

kbtab->dev.absmax[ABS_X] = 0x2000;
kbtab->dev.absmax[ABS_Y] = 0x1750;
- kbtab->dev.absmax[ABS_PRESSURE] = 0xff;
+ kbtab->dev.absmax[ABS_PRESSURE] = 0x7F;

- kbtab->dev.absfuzz[ABS_X] = 4;
- kbtab->dev.absfuzz[ABS_Y] = 4;
+ kbtab->dev.absfuzz[ABS_X] = 0;
+ kbtab->dev.absfuzz[ABS_Y] = 0;
+ kbtab->dev.absfuzz[ABS_PRESSURE] = 2;

kbtab->dev.private = kbtab;
kbtab->dev.open = kbtab_open;