brouting on interfaces without IP
Op do, 13-10-2005 te 23:55 +0200, schreef Carl-Daniel Hailfinger:
Quoted 10 lines
bridge:~ # ebtables -t nat -L --Lx
ebtables -t nat -N ifacefilter-int
ebtables -t nat -N proxy
ebtables -t nat -A PREROUTING -i bridgeint -j ifacefilter-int ebtables -t nat -A ifacefilter-int -p IPv4 --ip-src 192.168.0.0/24 --ip-proto tcp --ip-dport 80 -j proxy
ebtables -t nat -A proxy -j mark --set-mark0x1--mark-target CONTINUE
Quoted 2 lines
ebtables -t nat -A proxy -j dnat --to-dst 00:11:22:33:44:55 --dnat-target ACCEPT
Make this 00:01:02:03:04:05, or just use -j redirect
cheers,
Bart
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Quoted 17 lines · Bart De Schuymer
Op do, 13-10-2005 te 23:55 +0200, schreef Carl-Daniel Hailfinger:
Quoted 14 lines
However, once I insert the ebtables rule to actually do the redirection, all packets I want to redirect get dropped. This happens regardless of where I try to broute the packets. I tried DROPping them in BROUTING, REDIRECTing them in PREROUTING, DNATing them to the MAC of eth0 in PREROUTING, but each time the packets never leave eth0.
[...]
bridge:~ # ebtables -t nat -L --Lx
ebtables -t nat -N ifacefilter-int ebtables -t nat -N proxy ebtables -t nat -A PREROUTING -i bridgeint -j ifacefilter-int ebtables -t nat -A ifacefilter-int -p IPv4 --ip-src 192.168.0.0/24 --ip-proto tcp --ip-dport 80 -j proxy
ebtables -t nat -A proxy -j mark --set-mark0x1--mark-target CONTINUE
Quoted 5 lines
Quoted 2 lines
ebtables -t nat -A proxy -j dnat --to-dst 00:11:22:33:44:55 --dnat-target ACCEPT
Make this 00:01:02:03:04:05, or just use -j redirect
Sorry if I was unclear, but -j redirect doesn't work. Same for --to-dst 00:01:02:03:04:05. That's why I tried to use the MAC of eth0 in --to-dst.
Regards,
Carl-Daniel
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
Op di, 18-10-2005 te 02:03 +0200, schreef Carl-Daniel Hailfinger:
Quoted 18 lines
Quoted 17 lines · Bart De Schuymer
Op do, 13-10-2005 te 23:55 +0200, schreef Carl-Daniel Hailfinger:
Quoted 14 lines
However, once I insert the ebtables rule to actually do the redirection, all packets I want to redirect get dropped. This happens regardless of where I try to broute the packets. I tried DROPping them in BROUTING, REDIRECTing them in PREROUTING, DNATing them to the MAC of eth0 in PREROUTING, but each time the packets never leave eth0.
[...]
bridge:~ # ebtables -t nat -L --Lx
ebtables -t nat -N ifacefilter-int ebtables -t nat -N proxy ebtables -t nat -A PREROUTING -i bridgeint -j ifacefilter-int ebtables -t nat -A ifacefilter-int -p IPv4 --ip-src 192.168.0.0/24 --ip-proto tcp --ip-dport 80 -j proxy
ebtables -t nat -A proxy -j mark --set-mark0x1--mark-target CONTINUE
Quoted 8 lines
Quoted 5 lines
Quoted 2 lines
ebtables -t nat -A proxy -j dnat --to-dst 00:11:22:33:44:55 --dnat-target ACCEPT
Make this 00:01:02:03:04:05, or just use -j redirect
Sorry if I was unclear, but -j redirect doesn't work. Same for --to-dst 00:01:02:03:04:05. That's why I tried to use the MAC of eth0 in --to-dst.
OK. Anyway, you need to use the MAC address of the logical bridge device.
Please first try it with a simpler setup in which you don't need to mark the packet, using a simple routing table.
Do any packets leave on eth0?
cheers,
Bart
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc