Areca RAID driver remaining items?
Subsystems (3)
This appears to be the most current version of the driver:
ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.16-rc4/2.6.16-rc4-mm1/broken-out/areca-raid-linux-scsi-driver.patch
Is this the current TODO list?
=================
Issues not yet patched:
13. uintNN_t int types: use kernel types except for userspace interfaces
14. use kernel-doc
18. Put arcmsr.txt in Documentation/scsi/, not in scsi/arcmsr/.
19. Maybe use sysfs (/sys) instead of /proc.
20. check stack usage, init/exit sections;
=================
At one point this comment was made:
"There's lots of architectural problems. It's doing it's own queueing, it's stuffing kernel structures into memory on the hardware and so on. Basically someone knowledgeable about the hardware needs to start from scratch on it."
What are the show stoppers that prevents a merge into the Linus tree?
Dax Kelson
Quoted 7 lines
"There's lots of architectural problems. It's doing it's own queueing, it's stuffing kernel structures into memory on the hardware and so on. Basically someone knowledgeable about the hardware needs to start from scratch on it."
What are the show stoppers that prevents a merge into the Linus tree?
own queueing for sure is a show stopper;
stuffing kernel structures into the hw is also very much evil
Quoted 9 lines · Dax Kelson
This appears to be the most current version of the driver:
ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.16-rc4/2.6.16-rc4-mm1/broken-out/areca-raid-linux-scsi-driver.patch
Is this the current TODO list?
=================
Issues not yet patched:
Quoted 6 lines
13.
uintNN_tint types: use kernel types except for userspace interfaces
14. use kernel-doc
18. Put arcmsr.txt inDocumentation/scsi/, not in scsi/arcmsr/.
19. Maybe use sysfs (/sys) instead of /proc.
20. check stack usage, init/exit sections;
- remove internal queueing
- fix hardware datastructures
- remove odd ioctls
- remove useless forward prototypes
- give types like ACB useful names
- give variable useful names, especially follow kernel conventions, e.g. a struct pci_dev is usually named pdev
- kill ->proc_info method
- use normal comment style even for comments not fitting into the kernel-doc item above. kill useless separator comments without text
- convert arcmsr_show_firmware_info to useful one value per file attributes. best follow the schemes used in aacraid or lpfc
- convert arcmsr_show_driver_state to useful one value per file attributes.
- remove never called release method in the host template
- audit whether setting unchecked_isa_dma to false really makes sense (I strongly doubt it)
- remove shutdown notifier, add pci_driver ->shutdown method instead
- remove CameCase PCI Ids. The vendor Id should go into pci_ids.h, the device ids either removed or spelled the normal linux way
- arcmsr_do_interrupt should stop walking the global host list and use the private data passed to request_irq
- the global host list should go away completely
- arcmsr_bios_param looks like duplicating the generic CAM version?
- locking needs to be redone. If the driver really needs more than one per-host lock we'll want a very good explanation
- arcmsr_device_probe needs to be rewritten to do goto-based error unwinding.
- msi should be a module options if at all, but defintitly not a config options
- arcmsr_scsi_host_template_init should go away. the host template must be initialized statically with no run-time writes to it
- the hardware documentation should be split out of arcmsr.h into a separate file (btw, thanks a lot to areca to provide such detailed hardware informations, it's just the wrong format..)
- remove the SCSISTAT_* defines, and use the generic ones from <scsi/scsi.h> instead. Dito for various other SAM defines.
- the driver has just two files and should go directly into drivers/scsi instead of a subdirectory
Hi Christoph Hellwig,
Thanks for your comment with "arcmsr".
I will follow your comment to redo this driver.
But I am confuse with your mention about some items.
Hope you can tell me more detail and let me realy know your comment.
1- remove internal queueing:
Does the "internal queueing" is mention with arcmsr of ccb_free_list ?
2- fix hardware datastructures:
Does the "fix hardware datastructures" is to fix struct ARCMSR_CDB? Is it illeagal in linux?
3- remove odd ioctls:
How about remove odd ioctl?
Best Regards
Erich Chen
----- Original Message ----- From: "Christoph Hellwig" <[email protected]>
To: "Dax Kelson" <[email protected]>
Cc: <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>
Sent: Tuesday, February 21, 2006 2:20 AM
Subject: Re: Areca RAID driver remaining items?
Quoted 59 lines · Dax Kelson
Quoted 9 lines
This appears to be the most current version of the driver:
ftp://ftp.kernel.org/pub/linux/kernel/people/akpm/patches/2.6/2.6.16-rc4/2.6.16-rc4-mm1/broken-out/areca-raid-linux-scsi-driver.patch
Is this the current TODO list?
=================
Issues not yet patched:Quoted 6 lines
13.
uintNN_tint types: use kernel types except for userspace interfaces
14. use kernel-doc
18. Put arcmsr.txt inDocumentation/scsi/, not in scsi/arcmsr/.
19. Maybe use sysfs (/sys) instead of /proc.
20. check stack usage, init/exit sections;- remove internal queueing
- fix hardware datastructures
- remove odd ioctls
- remove useless forward prototypes
- give types like ACB useful names
- give variable useful names, especially follow kernel conventions, e.g. a structpci_devis usually named pdev
- kill ->proc_info method
- use normal comment style even for comments not fitting into the kernel-doc item above. kill useless separator comments without text
- convertarcmsr_show_firmware_infoto useful one value per file attributes. best follow the schemes used in aacraid or lpfc
- convertarcmsr_show_driver_stateto useful one value per file attributes.
- remove never called release method in the host template
- audit whether settingunchecked_isa_dmato false really makes sense (I strongly doubt it)
- remove shutdown notifier, addpci_driver->shutdown method instead
- remove CameCase PCI Ids. The vendor Id should go intopci_ids.h, the device ids either removed or spelled the normal linux way
-arcmsr_do_interruptshould stop walking the global host list and use the private data passed torequest_irq
- the global host list should go away completely
-arcmsr_bios_paramlooks like duplicating the generic CAM version?
- locking needs to be redone. If the driver really needs more than one per-host lock we'll want a very good explanation
-arcmsr_device_probeneeds to be rewritten to do goto-based error unwinding.
- msi should be a module options if at all, but defintitly not a config options
-arcmsr_scsi_host_template_initshould go away. the host template must be initialized statically with no run-time writes to it
- the hardware documentation should be split out ofarcmsr.hinto a separate file (btw, thanks a lot to areca to provide such detailed hardware informations, it's just the wrong format..)
- remove the SCSISTAT_* defines, and use the generic ones from <scsi/scsi.h> instead. Dito for various other SAM defines.
- the driver has just two files and should go directly intodrivers/scsiinstead of a subdirectory
Quoted 10 lines · erich
Hi Christoph Hellwig,
Thanks for your comment with "arcmsr".
I will follow your comment to redo this driver.
But I am confuse with your mention about some items.
Hope you can tell me more detail and let me realy know your comment.1- remove internal queueing:
Does the "internal queueing" is mention with arcmsr of
ccb_free_list?
Currently the drivers queuecommand routine works the following:
1) perform some checks
2) try to post outstanding ccbs
3) grab new ccb from freelist and set it up
4) try to post new ccb, else enqueue it
there is not poin in having such a pending queue in the driver because the midlayer does that work for you. If ->queuecommand can't immediately post a ccb you should return
SCSI_MLQUEUE_HOST_BUSY if there is a resource shortage at the hba level
SCSI_MLQUEUE_DEVICE_BUSY if there is a resource shortage at the device level
and the scsi midlayer will try to send the command again once a command has been completed on the hba/device.
Quoted 4 lines
2- fix hardware datastructures:
Does the "fix hardware datastructures" is to fix struct
ARCMSR_CDB? Is it illeagal in linux?
struct CCB is a structure that is passed to the hardware but contains pointers which have different sized on different architectures. This is generally very dangerous. If this is just a cookie that the hardware doesn't interpret at all it needs more documentation. Also the way you try to convert from bus to virtual addresses with pACB->vir2phy_offset can't work on many linux platforms because the virtual to bus address mapping isn't contingous. you need a separate dma mapping for each ccb, a good way to archive that is the dma_pool_ * API.
Quoted 3 lines
3- remove odd ioctls:
How about remove odd ioctl?
generally we don't want to add new ioctls. For scsi/raid drivers there's been an exception where we allow a pass-through to the firmware which the managment applications need. the driver has various ioctls that don't seem to fall into that category.
Dear Christoph Hellwig,
I have figure out your comments about "remove internal queueing" and "remove odd ioctl".
But about "hardware datastructures", areca's firmware spec is need to get a trunk of contingous memory space under 4G. In 64bit platform arcmsr need to make sure all ccbs have same of ccb_phyaddr_hi32 physical address. If arcmsr use dma_pool_alloc do a separate dma mapping.
Is there any method to avoid ccbs pool cross 4G segment?
- msi should be a module options if at all, but defintitly not a config options
In some mainboard if I always enable msi function, it will cause system hang up. If it is not a config option, do you have any idea to avoid this issue?
Best Regards
Erich Chen
----- Original Message ----- From: "Christoph Hellwig" <[email protected]>
To: "erich" <[email protected]>
Cc: <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>
Sent: Wednesday, February 22, 2006 10:57 PM
Subject: Re: Areca RAID driver remaining items?
Quoted 53 lines · erich
Quoted 11 lines
Hi Christoph Hellwig,
Thanks for your comment with "arcmsr".
I will follow your comment to redo this driver.
But I am confuse with your mention about some items.
Hope you can tell me more detail and let me realy know your comment.1- remove internal queueing:
Does the "internal queueing" is mention with arcmsr of
ccb_free_list
?Currently the drivers queuecommand routine works the following:
1) perform some checks
2) try to post outstanding ccbs
3) grab new ccb from freelist and set it up
4) try to post new ccb, else enqueue itthere is not poin in having such a pending queue in the driver because the midlayer does that work for you. If ->queuecommand can't immediately post a ccb you should return
SCSI_MLQUEUE_HOST_BUSYif there is a resource shortage at the hba levelSCSI_MLQUEUE_DEVICE_BUSYif there is a resource shortage at the device leveland the scsi midlayer will try to send the command again once a command has been completed on the hba/device.
Quoted 4 lines
2- fix hardware datastructures:
Does the "fix hardware datastructures" is to fix struct
ARCMSR_CDB? Is it illeagal in linux?struct CCB is a structure that is passed to the hardware but contains pointers which have different sized on different architectures. This is generally very dangerous. If this is just a cookie that the hardware doesn't interpret at all it needs more documentation. Also the way you try to convert from bus to virtual addresses with
pACB->vir2phy_offsetcan't work on many linux platforms because the virtual to bus address mapping isn't contingous. you need a separate dma mapping for each ccb, a good way to archive that is thedma_pool_* API.Quoted 3 lines
3- remove odd ioctls:
How about remove odd ioctl?
generally we don't want to add new ioctls. For scsi/raid drivers there's been an exception where we allow a pass-through to the firmware which the managment applications need. the driver has various ioctls that don't seem to fall into that category.
Quoted 10 lines · erich
Dear Christoph Hellwig,
I have figure out your comments about "remove internal queueing" and "remove odd ioctl".
But about "hardware datastructures", areca's firmware spec is need to get a trunk of contingous memory space under 4G.
In 64bit platform arcmsr need to make sure all ccbs have same ofccb_phyaddr_hi32physical address.
If arcmsr usedma_pool_allocdo a separate dma mapping.
Is there any method to avoid ccbs pool cross 4G segment?
the pci mapping layer prevents that already entirely; there is a LOT of hardware that cannot deal with segments crossing 4G boundaries, so much in fact that it's now generically disabled.
Quoted 3 lines
In some mainboard if I always enable msi function, it will cause system hang up.
If it is not a config option, do you have any idea to avoid this issue?
how about a module option (module_param)?
Dear Arjan van de Ven,
The following contex is coming from comment of Christoph Hellwig.
- msi should be a module options if at all, but defintitly not a config options
#ifdef CONFIG_SCSI_ARCMSR_MSI
if (!pci_enable_msi(pci_device))
pACB->acb_flags |= ACB_F_HAVE_MSI;
#endif
I make an option config for prevent some mainboards hang up if arcmsr enable msi function. Areca RAID controller is bridged hardware.
There were a lots of mainboards had wrong IRQ routing table issue with it.
If somebody meet this issue and people can enable msi function to fix its hardware bug. But unfortunately I found some mainboards will hang up if I always enable this function in my lab. To avoid this issue, I do an option for this case.
But Christoph Hellwig give me comment with it.
Best Regards
Erich Chen
----- Original Message ----- From: "Arjan van de Ven" <[email protected]>
To: "erich" <[email protected]>
Cc: "Christoph Hellwig" <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>
Sent: Thursday, February 23, 2006 4:25 PM
Subject: Re: Areca RAID driver remaining items?
Quoted 24 lines · erich
Quoted 10 lines
Dear Christoph Hellwig,
I have figure out your comments about "remove internal queueing" and "remove odd ioctl".
But about "hardware datastructures", areca's firmware spec is need to get a trunk of contingous memory space under 4G.
In 64bit platform arcmsr need to make sure all ccbs have same ofccb_phyaddr_hi32physical address.
If arcmsr usedma_pool_allocdo a separate dma mapping.
Is there any method to avoid ccbs pool cross 4G segment?the pci mapping layer prevents that already entirely; there is a LOT of hardware that cannot deal with segments crossing 4G boundaries, so much in fact that it's now generically disabled.
Quoted 3 lines
In some mainboard if I always enable msi function, it will cause system hang up.
If it is not a config option, do you have any idea to avoid this issue?how about a module option (
module_param)?
Quoted 12 lines · erich
Dear Arjan van de Ven,
The following contex is coming from comment of Christoph Hellwig.
- msi should be a module options if at all, but defintitly not a config options
#ifdef
CONFIG_SCSI_ARCMSR_MSI
if (!pci_enable_msi(pci_device))
pACB->acb_flags|=ACB_F_HAVE_MSI;
#endif
Quoted 9 lines
I make an option config for prevent some mainboards hang up if arcmsr enable msi function.
Areca RAID controller is bridged hardware.
There were a lots of mainboards had wrong IRQ routing table issue with it. If somebody meet this issue and people can enable msi function to fix its hardware bug.
But unfortunately I found some mainboards will hang up if I always enable this function in my lab.
To avoid this issue, I do an option for this case.
yes the reason for making this optional is clear, and Christoph also understands that.
However the idea that Christoph is proposing is to not make it a compile time option, but a runtime option. Compile-time is not very flexible, especially not for linux distributions. Making it a module option means it becomes runtime behavior, and the user can load the module like
modprobe aerca msi=0
and msi gets turned off. No need to recompile anything! That has many advantages over a more inflexible (from the user view) compiletime-only option.
Dear Arjan van de Ven,
Thanks for your answer.
I will remove CONFIG_SCSI_ARCMSR_MSI in next patch.
If Linux can not assurent the contingous memory space allocating of "dma_alloc_coherent" . When arcmsr get a physical ccb address from areca's firmware.
Does linux has any functions for converting of "bus to virtual" ?
Best Regards
Erich Chen
----- Original Message ----- From: "Arjan van de Ven" <[email protected]>
To: "erich" <[email protected]>
Cc: ""Christoph Hellwig"" <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>
Sent: Thursday, February 23, 2006 5:56 PM
Subject: Re: Areca RAID driver remaining items?
Quoted 39 lines · erich
Quoted 12 lines
Dear Arjan van de Ven,
The following contex is coming from comment of Christoph Hellwig.
- msi should be a module options if at all, but defintitly not a config options
#ifdef
CONFIG_SCSI_ARCMSR_MSI
if (!pci_enable_msi(pci_device))
pACB->acb_flags|=ACB_F_HAVE_MSI;
#endifQuoted 9 lines
I make an option config for prevent some mainboards hang up if arcmsr enable msi function.
Areca RAID controller is bridged hardware.
There were a lots of mainboards had wrong IRQ routing table issue with it. If somebody meet this issue and people can enable msi function to fix its hardware bug.
But unfortunately I found some mainboards will hang up if I always enable this function in my lab.
To avoid this issue, I do an option for this case.yes the reason for making this optional is clear, and Christoph also understands that.
However the idea that Christoph is proposing is to not make it a compile time option, but a runtime option. Compile-time is not very flexible, especially not for linux distributions. Making it a module option means it becomes runtime behavior, and the user can load the module like
modprobe aerca msi=0
and msi gets turned off. No need to recompile anything! That has many advantages over a more inflexible (from the user view) compiletime-only option.
Quoted 2 lines · erich
If Linux can not assurent the contingous memory space allocating of "
dma_alloc_coherent" .
coherent memory is guaranteed to be in the "lower" 32 bit of memory! So that is good news, I think you are just fine.
[Exception is that you can say that you are ok with a bigger mask for this type of memory, but just don't do that if you're not]
Quoted 2 lines
When arcmsr get a physical ccb address from areca's firmware. Does linux has any functions for converting of "bus to virtual" ?
not without using pools. You would have to search the list of memory you gave it to find that out.
(USB has a similar problem, afaik they solved it with pools)
Dear Arjan van de Ven,
I would keep dma_alloc_coherent usage.
Quoted 2 lines
[Exception is that you can say that you are ok with a bigger mask for this type of memory, but just don't do that if you're not]
Should I remove "pci_set_dma_mask(pci_device, DMA_64BIT_MASK)" for this case?
Best Regards
Erich Chen
----- Original Message ----- From: "Arjan van de Ven" <[email protected]>
To: "erich" <[email protected]>
Cc: """Christoph Hellwig""" <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>
Sent: Thursday, February 23, 2006 8:07 PM
Subject: Re: Areca RAID driver remaining items?
Quoted 20 lines · erich
Quoted 2 lines
If Linux can not assurent the contingous memory space allocating of "
dma_alloc_coherent" .coherent memory is guaranteed to be in the "lower" 32 bit of memory! So that is good news, I think you are just fine.
[Exception is that you can say that you are ok with a bigger mask for this type of memory, but just don't do that if you're not]
Quoted 2 lines
When arcmsr get a physical ccb address from areca's firmware. Does linux has any functions for converting of "bus to virtual" ?
not without using pools. You would have to search the list of memory you gave it to find that out.
(USB has a similar problem, afaik they solved it with pools)
Quoted 9 lines · erich
Dear Arjan van de Ven,
I would keep
dma_alloc_coherentusage.Quoted 2 lines
[Exception is that you can say that you are ok with a bigger mask for this type of memory, but just don't do that if you're not]
Should I remove "
pci_set_dma_mask(pci_device, DMA_64BIT_MASK)" for this case?
no what you have is correct; the function to change this behavior is calledpci_set_consistent_dma_mask()
pci_set_dma_mask() sets the mask for the "data" (eg dynamic mappings via pci_map_single and pci_map_page and such). pci_set_consistent_dma_mask() sets the mask for all the "consistent" allocators.
so again your code is fine as is. If you want to explicitly set that mask to DMA_32BIT_MASK as documentation that you REALLY want it to be 32 bit, that is probably fine too, but not really needed.
Greetings,
Arjan van de Ven
Quoted 5 lines · erich
But unfortunately I found some mainboards will hang up if I always enable this function in my lab.
To avoid this issue, I do an option for this case.But Christoph Hellwig give me comment with it.
Another thing you can also do for many of these cases is to use either the PCI or DMI interfaces to identify the problem board and automatically set the option as well.
There are two ways to do this. One is
struct pci_dev *bridge_dev = pci_get_slot(pdev->bus, PCI_DEVFN(0,0));
if(bridge_dev) {
if(bridge_dev->subsystem_vendor == 0xXXXX &&
bridge_dev->subsystem_device == 0xXXXX)
/* Match by svid/sdid for problem boards */The other is like this
#include <linux/dmi.h>
struct dmi_system_id problem_dmi_table[] = {
{
.ident = "Broken Board Name 1",
.matches = {
DMI_MATCH(DMI_SYS_VENDOR, "EvilCorp");
DMI_MATCH(DMI_PRODUCTNAME, "Wombat 1000");
}
}
{
ditto per board
},
{ } /* End of list mark
};And then
if (dmi_system_check(problem_dmi_table))
disable_msi..
The DMI code matches on the DMI strings in the ROM BIOS (the ones dumped by 'dmidecode')
An example driver using this interface is drivers/char/sonypi.c which uses it to make sure it *is* only run on a sony laptop.
Alan
Dear Alan Cox,
This is good idea to make black list to prevent system hang up with MSI function. But arcmsr need to come up against none specific mainboards.
The case at my lab have same chipset but different maker.
Best Regards
Erich Chen
----- Original Message ----- From: "Alan Cox" <[email protected]>
To: "erich" <[email protected]>
Cc: "Arjan van de Ven" <[email protected]>; ""Christoph Hellwig"" <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>; <[email protected]>
Sent: Thursday, February 23, 2006 7:59 PM
Subject: Re: Areca RAID driver remaining items?
Quoted 54 lines · erich
Quoted 5 lines
But unfortunately I found some mainboards will hang up if I always enable this function in my lab.
To avoid this issue, I do an option for this case.But Christoph Hellwig give me comment with it.
Another thing you can also do for many of these cases is to use either the PCI or DMI interfaces to identify the problem board and automatically set the option as well.
There are two ways to do this. One is
struct
pci_dev*bridge_dev=pci_get_slot(pdev->bus, PCI_DEVFN(0,0));if(bridge_dev){if(bridge_dev->subsystem_vendor == 0xXXXX && bridge_dev->subsystem_device == 0xXXXX)
/* Match by svid/sdid for problem boards */The other is like this
#include <
linux/dmi.h>struct
dmi_system_idproblem_dmi_table[] = {
{
.ident = "Broken Board Name 1",
.matches = {DMI_MATCH(DMI_SYS_VENDOR, "EvilCorp");DMI_MATCH(DMI_PRODUCTNAME, "Wombat 1000");
}
}
{
ditto per board
},
{ } /* End of list mark
};And then
if (
dmi_system_check(problem_dmi_table))disable_msi..The DMI code matches on the DMI strings in the ROM BIOS (the ones dumped by 'dmidecode')
An example driver using this interface is
drivers/char/sonypi.cwhich uses it to make sure it *is* only run on a sony laptop.Alan
Quoted 5 lines · Alan Cox
Quoted 4 lines · erich
But unfortunately I found some mainboards will hang up if I always enable this function in my lab.
To avoid this issue, I do an option for this case.
Quoted 8 lines
Quoted 1 line
But Christoph Hellwig give me comment with it.
Another thing you can also do for many of these cases is to use either the PCI or DMI interfaces to identify the problem board and automatically set the option as well.
There are two ways to do this. One is
Please avoid that unless really nessecary. I doubt there's boards where MSI would only be broken with the areca card but not with other MSI-capable ones. If a board or chipset is generally broken vs MSI it should be added to the global MSI blacklist. It's probably be nice to have a global nomsi boot option instead of one in every driver aswell..
Quoted 13 lines · Christoph Hellwig
Quoted 12 lines · Alan Cox
Quoted 5 lines · erich
But unfortunately I found some mainboards will hang up if I always enable this function in my lab.
To avoid this issue, I do an option for this case.But Christoph Hellwig give me comment with it.
Another thing you can also do for many of these cases is to use either the PCI or DMI interfaces to identify the problem board and automatically set the option as well.
Quoted 7 lines
Quoted 1 line
There are two ways to do this. One is
Please avoid that unless really nessecary. I doubt there's boards where MSI would only be broken with the areca card but not with other MSI-capable ones. If a board or chipset is generally broken vs MSI it should be added to the global MSI blacklist. It's probably be nice to have a global nomsi boot option instead of one in every driver aswell..
Jeff G. added an "msi" option to the sata_mv driver recently. But yes, I expect it to be more of a platform issue than a driver issue.
s2io network people report MSI interrupt problems on various platforms (on netdev mailing list).
There are other reports (that I have at home, not visible to me now). It would be good to have an MSI expert around.
http://www.xenotime.net/linux/patches/pci_nomsi.patch adds a global boot option to disable MSI interrupt assignments.
Signature · 1 line
~Randy
Quoted 9 lines · Randy.Dunlap
Quoted 5 lines · Christoph Hellwig
Please avoid that unless really nessecary. I doubt there's boards where MSI would only be broken with the areca card but not with other MSI-capable ones. If a board or chipset is generally broken vs MSI it should be added to the global MSI blacklist. It's probably be nice to have a global nomsi boot option instead of one in every driver aswell..
http://www.xenotime.net/linux/patches/pci_nomsi.patch adds a global boot option to disable MSI interrupt assignments.
I like it. How about adding pci=nomsi instead of pci_nomsi?
pci/pci.c 24 Feb 2006 19:33:25 -0000 renamed from pci/pci.c 4 Feb 2006 04:51:55 -0000 1.28 +6 -2
@@ -900,8 +900,12 @@ static int __devinit pci_setup(char *str if (k) *k++ = 0; if (*str && (str = pcibios_setup(str)) && *str) { - /* PCI layer options should be handled here */ - printk(KERN_ERR "PCI: Unknown option `%s'\n", str); + if (!strcmp(str, "nomsi")) { + pci_msi_enable = 0; + } else { + printk(KERN_ERR "PCI: Unknown option `%s'\n", + str); + } } str = k; }
Quoted 8 lines · Matthew Wilcox
Quoted 7 lines · Randy.Dunlap
Quoted 5 lines · Christoph Hellwig
Please avoid that unless really nessecary. I doubt there's boards where MSI would only be broken with the areca card but not with other MSI-capable ones. If a board or chipset is generally broken vs MSI it should be added to the global MSI blacklist. It's probably be nice to have a global nomsi boot option instead of one in every driver aswell..
Quoted 4 lines
Quoted 2 lines
http://www.xenotime.net/linux/patches/pci_nomsi.patch adds a global boot option to disable MSI interrupt assignments.
I like it. How about adding pci=nomsi instead of
pci_nomsi?
Yes, that's probably better. Thanks for the change.
Quoted 19 lines
pci/pci.c 24 Feb 2006 19:33:25 -0000 renamed from pci/pci.c 4 Feb 2006 04:51:55 -0000 1.28 +6
-2@@ -900,8 +900,12 @@ static int __devinit pci_setup(char *str if (k) *k++ = 0; if (*str && (str = pcibios_setup(str)) && *str) { - /* PCI layer options should be handled here */ - printk(KERN_ERR "PCI: Unknown option `%s'\n", str); + if (!strcmp(str, "nomsi")) { + pci_msi_enable = 0; + } else { + printk(KERN_ERR "PCI: Unknown option `%s'\n", + str); + } } str = k; }
Signature · 1 line
~Randy
Quoted 19 lines · On Fri, 24 Feb 2006 12:38:30 -0700 Matthew Wilcox wrote:
Quoted 9 lines · Randy.Dunlap
Quoted 5 lines · Christoph Hellwig
Please avoid that unless really nessecary. I doubt there's boards where MSI would only be broken with the areca card but not with other MSI-capable ones. If a board or chipset is generally broken vs MSI it should be added to the global MSI blacklist. It's probably be nice to have a global nomsi boot option instead of one in every driver aswell..
http://www.xenotime.net/linux/patches/pci_nomsi.patch adds a global boot option to disable MSI interrupt assignments.
I like it. How about adding pci=nomsi instead of
pci_nomsi?pci/pci.c 24 Feb 2006 19:33:25 -0000 renamed from pci/pci.c 4 Feb 2006 04:51:55 -0000 1.28 +0
-0@@ -900,8 +900,12 @@ static int __devinit pci_setup(char *str if (k) *k++ = 0; if (*str && (str = pcibios_setup(str)) && *str) {
pci/pci.c 24 Feb 2006 19:33:25 -0000 static int __devinit pci_setup(char *str · line 910
Quoted 10 lines
pci/pci.c 24 Feb 2006 19:33:25 -0000 renamed from pci/pci.c 4 Feb 2006 04:51:55 -0000 1.28 +6
-2- /* PCI layer options should be handled here */ - printk(KERN_ERR "PCI: Unknown option `%s'\n", str); + if (!strcmp(str, "nomsi")) { + pci_msi_enable = 0; + } else { + printk(KERN_ERR "PCI: Unknown option `%s'\n", + str); + } } str = k;
OK, updated patch for "pci=nomsi" is now at
http://www.xenotime.net/linux/patches/pci_nomsi.patch
Thanks.
---
~Randy
Quoted 2 lines · Randy.Dunlap
OK, updated patch for "pci=nomsi" is now at
http://www.xenotime.net/linux/patches/pci_nomsi.patch
After sleeping on it, I realised this wouldn't work if CONFIG_PCI_MSI is disabled. So how about this (not even compile-tested):
Index: ./Documentation/kernel-parameters.txt
===================================================================
RCS file: /var/cvs/linux-2.6/Documentation/kernel-parameters.txt,v retrieving revision 1.41.4.1
Documentation/kernel-parameters.txt +4 -0
@@ -49,6 +49,7 @@ restrictions referred to are that the re MCA MCA bus support is enabled. MDA MDA console support is enabled. MOUSE Appropriate mouse support is enabled. + MSI Message Signaled Interrupts (PCI). MTD MTD support is enabled. NET Appropriate network support is enabled. NUMA NUMA support is enabled.
@@ -1135,6 +1136,9 @@ running once the system is up. Mechanism 2. nommconf [IA-32,X86_64] Disable use of MMCONFIG for PCI Configuration + nomsi [MSI] If the PCI_MSI kernel config parameter is + enabled, this kernel boot option can be used to + disable the use of MSI interrupts system-wide. nosort [IA-32] Don't sort PCI devices according to order given by the PCI BIOS. This sorting is done to get a device order compatible with
Index: ./drivers/pci/Kconfig
===================================================================
RCS file: /var/cvs/linux-2.6/drivers/pci/Kconfig,v retrieving revision 1.8
drivers/pci/Kconfig +4 -0
@@ -11,6 +11,10 @@ config PCI_MSI generate an interrupt using an inbound Memory Write on its PCI bus instead of asserting a device IRQ pin. + Use of PCI MSI interrupts can be disabled at kernel boot time + by using the 'pci=nomsi' option. This disables MSI for the + entire system. + If you don't know what to do here, say N. config PCI_LEGACY_PROC
Index: ./drivers/pci/msi.c
===================================================================
RCS file: /var/cvs/linux-2.6/drivers/pci/msi.c,v
retrieving revision 1.17
drivers/pci/msi.c +11 -0
@@ -755,6 +755,9 @@ void pci_disable_msi(struct pci_dev* devu16 control;unsigned long flags; +if (!pci_msi_enable) +return ; +if (!dev || !(pos =pci_find_capability (dev,PCI_CAP_ID_MSI )))return ;
@@ -1006,6 +1009,9 @@ void pci_disable_msix(struct pci_dev* deint pos, temp;u16 control; +if (!pci_msi_enable) +return ; +if (!dev || !(pos =pci_find_capability (dev,PCI_CAP_ID_MSIX )))return ;
@@ -1121,6 +1127,11 @@ void msi_remove_pci_irq_vectors(struct p } dev->irq = temp;/* Restore IOAPIC IRQ */ } +} + +void pci_no_msi (void ) +{ + pci_msi_enable =0 ; }EXPORT_SYMBOL (pci_enable_msi);
Index: ./drivers/pci/pci.c
===================================================================
RCS file: /var/cvs/linux-2.6/drivers/pci/pci.c,v
retrieving revision 1.28
drivers/pci/pci.c +6 -2
@@ -900,8 +900,12 @@ static int __devinit pci_setup(char *strif (k) *k++ =0 ;if (*str && (str =pcibios_setup (str)) && *str) { -/* PCI layer options should be handled here */ -printk (KERN_ERR "PCI: Unknown option `%s'\n" , str); +if (!strcmp (str,"nomsi" )) { +pci_no_msi (); + }else { +printk (KERN_ERR "PCI: Unknown option `%s'\n" , + str); + } } str = k; }
Index: ./drivers/pci/pci.h
===================================================================
RCS file: /var/cvs/linux-2.6/drivers/pci/pci.h,v
retrieving revision 1.13
drivers/pci/pci.h +2 -0
@@ -50,8 +50,10 @@ extern int pci_msi_quirk;#ifdef CONFIG_PCI_MSI void disable_msi_mode (struct pci_dev *dev,int pos,int type); +void pci_no_msi (void );#else static inline void disable_msi_mode (struct pci_dev *dev,int pos,int type) { } +static inline void pci_no_msi (void ) { }#endif extern int pcie_mch_quirk;
Quoted 6 lines · On Sun, 26 Feb 2006 09:02:47 -0700 Matthew Wilcox wrote:
Quoted 2 lines · Randy.Dunlap
OK, updated patch for "pci=nomsi" is now at
http://www.xenotime.net/linux/patches/pci_nomsi.patchAfter sleeping on it, I realised this wouldn't work if
CONFIG_PCI_MSIis disabled. So how about this (not even compile-tested):
It's good. Thanks for catching that.
Quoted 1 line
Signed-off-by Matthew Wilcox <[email protected]>
Quoted 113 lines
Index:
./Documentation/kernel-parameters.txt
===================================================================
RCS file:/var/cvs/linux-2.6/Documentation/kernel-parameters.txt,vretrieving revision 1.41.4.1
diff -u -p -r1.41.4.1 kernel-parameters.txtDocumentation/kernel-parameters.txt +4
-0@@ -49,6 +49,7 @@ restrictions referred to are that the re MCA MCA bus support is enabled. MDA MDA console support is enabled. MOUSE Appropriate mouse support is enabled. + MSI Message Signaled Interrupts (PCI). MTD MTD support is enabled. NET Appropriate network support is enabled. NUMA NUMA support is enabled.@@ -1135,6 +1136,9 @@ running once the system is up. Mechanism 2. nommconf [IA-32,X86_64] Disable use of MMCONFIG for PCI Configuration + nomsi [MSI] If the PCI_MSI kernel config parameter is + enabled, this kernel boot option can be used to + disable the use of MSI interrupts system-wide. nosort [IA-32] Don't sort PCI devices according to order given by the PCI BIOS. This sorting is done to get a device order compatible withIndex:
./drivers/pci/Kconfig
===================================================================
RCS file:/var/cvs/linux-2.6/drivers/pci/Kconfig,vretrieving revision 1.8
diff -u -p -r1.8Kconfigdrivers/pci/Kconfig +4
-0@@ -11,6 +11,10 @@ config PCI_MSI generate an interrupt using an inbound Memory Write on its PCI bus instead of asserting a device IRQ pin. + Use of PCI MSI interrupts can be disabled at kernel boot time + by using the 'pci=nomsi' option. This disables MSI for the + entire system. + If you don't know what to do here, say N. config PCI_LEGACY_PROCIndex:
./drivers/pci/msi.c
===================================================================
RCS file:/var/cvs/linux-2.6/drivers/pci/msi.c,v
retrieving revision 1.17
diff -u -p -r1.17msi.cdrivers/pci/msi.c +11
-0@@ -755,6 +755,9 @@ void pci_disable_msi(struct pci_dev* devu16 control;unsigned long flags; +if (!pci_msi_enable) +return ; +if (!dev || !(pos =pci_find_capability (dev,PCI_CAP_ID_MSI )))return ;@@ -1006,6 +1009,9 @@ void pci_disable_msix(struct pci_dev* deint pos, temp;u16 control; +if (!pci_msi_enable) +return ; +if (!dev || !(pos =pci_find_capability (dev,PCI_CAP_ID_MSIX )))return ;@@ -1121,6 +1127,11 @@ void msi_remove_pci_irq_vectors(struct p } dev->irq = temp;/* Restore IOAPIC IRQ */ } +} + +void pci_no_msi (void ) +{ + pci_msi_enable =0 ; }EXPORT_SYMBOL (pci_enable_msi);Index:
./drivers/pci/pci.c
===================================================================
RCS file:/var/cvs/linux-2.6/drivers/pci/pci.c,v
retrieving revision 1.28
diff -u -p -r1.28pci.cdrivers/pci/pci.c +6
-2@@ -900,8 +900,12 @@ static int __devinit pci_setup(char *strif (k) *k++ =0 ;if (*str && (str =pcibios_setup (str)) && *str) { -/* PCI layer options should be handled here */ -printk (KERN_ERR "PCI: Unknown option `%s'\n" , str); +if (!strcmp (str,"nomsi" )) { +pci_no_msi (); + }else { +printk (KERN_ERR "PCI: Unknown option `%s'\n" , + str); + } } str = k; }Index:
./drivers/pci/pci.h
===================================================================
RCS file:/var/cvs/linux-2.6/drivers/pci/pci.h,v
retrieving revision 1.13
diff -u -p -r1.13pci.h
drivers/pci/pci.h extern int pci_msi_quirk; · line 59
Quoted 10 lines
drivers/pci/pci.h +2
-0@@ -50,8 +50,10 @@ extern int pci_msi_quirk;#ifdef CONFIG_PCI_MSI void disable_msi_mode (struct pci_dev *dev,int pos,int type); +void pci_no_msi (void );#else static inline void disable_msi_mode (struct pci_dev *dev,int pos,int type) { } +static inline void pci_no_msi (void ) { }#endif extern int pcie_mch_quirk;
---