sata_sil24: fixes, errata workaround and reset updates, take 2
PATCH 1/1 sata_sil24: fixes, errata workaround and reset updates, take 2
Hello, Jeff and Carlos.
This is the second take of sata_sil24-fixes-errata-workaround-and- reset-updates patchset. Changes from the last take[1] are...
* sil24_poll_register() is replaced by ata_wait_register()
* comment update as suggested by Jeff
* better constants
* byteorder fix and 64bit patches are pushed backward, as they're untested.
* hardreset routine updated to unconditionally wait 100ms after reset
* new patch #11 removes hardresetting in sil24_init_one() as it's already done during host reset and even if the port is in a funky state, we have hardreset to back us up.
This patchset contains 13 patches.
#01 prep
#02-06 fixes, updates, errata workaround
#07-09 update softreset
#10-11 update hardreset
#12-13 untested fixes
This patchset is against
upstream[2]
+ libata-reset-updates patchset (3 patches) [3]
+ implement-and-use-ata_wait_register patchset [4]
After these updates, sil24 is ready for new EN and NCQ. In my repo, sil24 is working fine with both new EH and NCQ.
Thanks.
--
tejun
[1] http://article.gmane.org/gmane.linux.ide/9406
[2] c2a6585296009379e0f4eff39cdcb108b457ebf2
[3] http://article.gmane.org/gmane.linux.ide/9414
[4] http://article.gmane.org/gmane.linux.ide/9450
PATCH 1/13 libata: export ata_set_sata_spd()
This will be used by LLDD hardreset implementation.
---
drivers/scsi/libata-core.c | 3 ++- include/linux/libata.h | 1 + 2 files changed, 3 insertions(+), 1 deletions(-)
850540dc36ec347cca6604f668804fc81b537660
drivers/scsi/libata-core.c +2 -1
@@ -1736,7 +1736,7 @@ int ata_set_sata_spd_needed(struct ata_p* 0 if spd doesn't need to be changed, 1 if spd has been * changed. -EOPNOTSUPP if SCR registers are inaccessible. */ -static int ata_set_sata_spd (struct ata_port *ap) +int ata_set_sata_spd (struct ata_port *ap) {u32 scontrol;
@@ -5111,6 +5111,7 @@ EXPORT_SYMBOL_GPL(ata_bmdma_irq_clear);EXPORT_SYMBOL_GPL (ata_bmdma_status);EXPORT_SYMBOL_GPL (ata_bmdma_stop);EXPORT_SYMBOL_GPL (ata_port_probe); +EXPORT_SYMBOL_GPL (ata_set_sata_spd);EXPORT_SYMBOL_GPL (sata_phy_reset);EXPORT_SYMBOL_GPL (__sata_phy_reset);EXPORT_SYMBOL_GPL (ata_bus_reset);
include/linux/libata.h +1 -0
@@ -503,6 +503,7 @@ extern void ata_port_probe(struct ata_poextern void __sata_phy_reset (struct ata_port *ap);extern void sata_phy_reset (struct ata_port *ap);extern void ata_bus_reset (struct ata_port *ap); +extern int ata_set_sata_spd (struct ata_port *ap); extern int ata_drive_probe_reset(struct ata_port *ap, ata_probeinit_fn_t probeinit, ata_reset_fn_t softreset, ata_reset_fn_t hardreset,
Signature · 1 line
1.2.4
PATCH 2/13 sata_sil24: typo fix
In reply to Tejun HeoType fix.
---
drivers/scsi/sata_sil24.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
9afd6d085d6de7b961216befcb0a20e8186ce48e
drivers/scsi/sata_sil24.c +1 -1
@@ -174,7 +174,7 @@ enum {PORT_CERR_CMD_PCIPERR =27 ,/* ctrl[15:13] 110 - PCI parity err while fetching PRB */ PORT_CERR_XFR_UNDEF =32 ,/* PSD ecode 00 - undefined */ PORT_CERR_XFR_TGTABRT =33 ,/* PSD ecode 01 - target abort */ -PORT_CERR_XFR_MSGABRT =34 ,/* PSD ecode 10 - master abort */ +PORT_CERR_XFR_MSTABRT =34 ,/* PSD ecode 10 - master abort */ PORT_CERR_XFR_PCIPERR =35 ,/* PSD ecode 11 - PCI prity err during transfer */ PORT_CERR_SENDSERVICE = 36, /* FIS received while sending service */
Signature · 1 line
1.2.4
PATCH 3/13 sata_sil24: rename PORT_IRQ_SDB_FIS to PORT_IRQ_SDB_NOTIFY
In reply to Tejun HeoRename PORT_IRQ_SDB_FIS to more proper PORT_IRQ_SDB_NOTIFY.
---
drivers/scsi/sata_sil24.c | 6 +++--- 1 files changed, 3 insertions(+), 3 deletions(-)
0ce72002ee4f709f166a6e2433b8a1c3ecc240b2
drivers/scsi/sata_sil24.c +3 -3
@@ -143,7 +143,7 @@ enum {PORT_IRQ_PHYRDY_CHG = (1 <<4 ),/* PHY ready change */ PORT_IRQ_COMWAKE = (1 <<5 ),/* COMWAKE received */ PORT_IRQ_UNK_FIS = (1 <<6 ),/* Unknown FIS received */ -PORT_IRQ_SDB_FIS = (1 <<11 ),/* SDB FIS received */ +PORT_IRQ_SDB_NOTIFY = (1 <<11 ),/* SDB notify received */ /* bits[27:16] are unmasked (raw) */ PORT_IRQ_RAW_SHIFT = 16,
@@ -975,8 +975,8 @@ static int sil24_init_one(struct pci_dev/* Configure interrupts */ writel (0xffff , port +PORT_IRQ_ENABLE_CLR ); -writel (PORT_IRQ_COMPLETE |PORT_IRQ_ERROR |PORT_IRQ_SDB_FIS , - port +PORT_IRQ_ENABLE_SET ); +writel (PORT_IRQ_COMPLETE |PORT_IRQ_ERROR | +PORT_IRQ_SDB_NOTIFY , port +PORT_IRQ_ENABLE_SET );/* Clear interrupts */ writel (0x0fff0fff , port +PORT_IRQ_STAT );
Signature · 1 line
1.2.4
PATCH 4/13 sata_sil24: add more constants
In reply to Tejun HeoAdd HOST_CTRL_* and more PORT_IRQ_* bits.
---
drivers/scsi/sata_sil24.c | 13 ++++++++++++- 1 files changed, 12 insertions(+), 1 deletions(-)
c5ccb983c5240ef095501f9e4558233904a39f42
drivers/scsi/sata_sil24.c +12 -1
@@ -86,6 +86,13 @@ enum {/* HOST_SLOT_STAT bits */ HOST_SSTAT_ATTN = (1 <<31 ), +/* HOST_CTRL bits */ +HOST_CTRL_M66EN = (1 <<16 ),/* M66EN PCI bus signal */ +HOST_CTRL_TRDY = (1 <<17 ),/* latched PCI TRDY */ +HOST_CTRL_STOP = (1 <<18 ),/* latched PCI STOP */ +HOST_CTRL_DEVSEL = (1 <<19 ),/* latched PCI DEVSEL */ +HOST_CTRL_REQ64 = (1 <<20 ),/* latched PCI REQ64 */ +/* * Port registers * (8192 bytes @ +0x0000, +0x2000, +0x4000 and +0x6000 @ BAR2)
@@ -142,7 +149,11 @@ enum {PORT_IRQ_PWR_CHG = (1 <<3 ),/* power management change */ PORT_IRQ_PHYRDY_CHG = (1 <<4 ),/* PHY ready change */ PORT_IRQ_COMWAKE = (1 <<5 ),/* COMWAKE received */ -PORT_IRQ_UNK_FIS = (1 <<6 ),/* Unknown FIS received */ +PORT_IRQ_UNK_FIS = (1 <<6 ),/* unknown FIS received */ +PORT_IRQ_DEV_XCHG = (1 <<7 ),/* device exchanged */ +PORT_IRQ_8B10B = (1 <<8 ),/* 8b/10b decode error threshold */ +PORT_IRQ_CRC = (1 <<9 ),/* CRC error threshold */ +PORT_IRQ_HANDSHAKE = (1 <<10 ),/* handshake error threshold */ PORT_IRQ_SDB_NOTIFY = (1 <<11 ),/* SDB notify received */ /* bits[27:16] are unmasked (raw) */
Signature · 1 line
1.2.4
PATCH 5/13 sata_sil24: consolidate host flags into SIL24_COMMON_FLAGS
In reply to Tejun HeoAll sil24 controllers share the same host flags except for NPORTS. Consolidate them into SIL24_COMMON_FLAGS.
---
drivers/scsi/sata_sil24.c | 16 +++++++--------- 1 files changed, 7 insertions(+), 9 deletions(-)
18f37254b289b3c8215e83f313e0dc53756f6c1d
drivers/scsi/sata_sil24.c +7 -9
@@ -218,6 +218,10 @@ enum {BID_SIL3132 =1 ,BID_SIL3131 =2 , +/* host flags */ +SIL24_COMMON_FLAGS =ATA_FLAG_SATA |ATA_FLAG_NO_LEGACY | +ATA_FLAG_MMIO |ATA_FLAG_PIO_DMA , + IRQ_STAT_4PORTS = 0xf, };
@@ -345,9 +349,7 @@ static struct ata_port_info sil24_port_i/* sil_3124 */ { .sht = &sil24_sht, - .host_flags =ATA_FLAG_SATA |ATA_FLAG_NO_LEGACY | -ATA_FLAG_MMIO |ATA_FLAG_PIO_DMA | - SIL24_NPORTS2FLAG(4), + .host_flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(4), .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = 0x3f, /* udma0-5 */
@@ -356,9 +358,7 @@ static struct ata_port_info sil24_port_i/* sil_3132 */ { .sht = &sil24_sht, - .host_flags =ATA_FLAG_SATA |ATA_FLAG_NO_LEGACY | -ATA_FLAG_MMIO |ATA_FLAG_PIO_DMA | - SIL24_NPORTS2FLAG(2), + .host_flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(2), .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = 0x3f, /* udma0-5 */
@@ -367,9 +367,7 @@ static struct ata_port_info sil24_port_i/* sil_3131/sil_3531 */ { .sht = &sil24_sht, - .host_flags =ATA_FLAG_SATA |ATA_FLAG_NO_LEGACY | -ATA_FLAG_MMIO |ATA_FLAG_PIO_DMA | - SIL24_NPORTS2FLAG(1), + .host_flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(1), .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = 0x3f, /* udma0-5 */
Signature · 1 line
1.2.4
PATCH 6/13 sata_sil24: implement loss of completion interrupt on PCI-X errta fix
In reply to Tejun HeoSiI3124 might lose completion interrupt if completion interrupt occurs shortly after SLOT_STAT register is read for the previous completion interrupt if it is operating in PCI-X mode.
This currently doesn't trigger as libata never queues more than one command, but it will with NCQ changes. This patch implements the workaround - turning on WoC and explicitly clearing interrupt.
---
drivers/scsi/sata_sil24.c | 27 +++++++++++++++++++++++++-- 1 files changed, 25 insertions(+), 2 deletions(-)
bfc72a2448cce3be32f0aae2927fb8643152ebcd
drivers/scsi/sata_sil24.c +25 -2
@@ -221,6 +221,7 @@ enum {/* host flags */ SIL24_COMMON_FLAGS =ATA_FLAG_SATA |ATA_FLAG_NO_LEGACY |ATA_FLAG_MMIO |ATA_FLAG_PIO_DMA , +SIL24_FLAG_PCIX_IRQ_WOC = (1 <<24 ),/* IRQ loss errata on PCI-X */ IRQ_STAT_4PORTS = 0xf, };
@@ -349,7 +350,8 @@ static struct ata_port_info sil24_port_i/* sil_3124 */ { .sht = &sil24_sht, - .host_flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(4), + .host_flags =SIL24_COMMON_FLAGS |SIL24_NPORTS2FLAG (4 ) | + SIL24_FLAG_PCIX_IRQ_WOC, .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = 0x3f, /* udma0-5 */
@@ -738,6 +740,10 @@ static inline void sil24_host_intr(struc slot_stat =readl (port +PORT_SLOT_STAT );if (!(slot_stat &HOST_SSTAT_ATTN )) {struct sil24_port_priv *pp = ap->private_data; + +if (ap->flags &SIL24_FLAG_PCIX_IRQ_WOC ) +writel (PORT_IRQ_COMPLETE , port +PORT_IRQ_STAT ); +/* * !HOST_SSAT_ATTN guarantees successful completion, * so reading back tf registers is unnecessary for
@@ -869,6 +875,7 @@ static int sil24_init_one(struct pci_devvoid __iomem *host_base =NULL ;void __iomem *port_base =NULL ;int i, rc; +u32 tmp;if (!printed_version++)dev_printk (KERN_DEBUG , &pdev->dev,"version " DRV_VERSION "\n" );
@@ -942,13 +949,23 @@ static int sil24_init_one(struct pci_dev/* GPIO off */ writel (0 , host_base +HOST_FLASH_CMD ); +/* Apply workaround for completion IRQ loss on PCI-X errata */ +if (probe_ent->host_flags &SIL24_FLAG_PCIX_IRQ_WOC ) { + tmp =readl (host_base +HOST_CTRL ); +if (tmp & (HOST_CTRL_TRDY |HOST_CTRL_STOP |HOST_CTRL_DEVSEL )) +dev_printk (KERN_INFO , &pdev->dev, +"Applying completion IRQ loss on PCI-X " +"errata fix\n" ); +else + probe_ent->host_flags &= ~SIL24_FLAG_PCIX_IRQ_WOC ; + } +/* clear global reset & mask interrupts during initialization */ writel (0 , host_base +HOST_CTRL );for (i =0 ; i < probe_ent->n_ports; i++) {void __iomem *port = port_base + i *PORT_REGS_SIZE ;unsigned long portu = (unsigned long )port; -u32 tmp; probe_ent->port[i].cmd_addr = portu +PORT_PRB ; probe_ent->port[i].scr_addr = portu +PORT_SCONTROL ;
@@ -958,6 +975,12 @@ static int sil24_init_one(struct pci_dev/* Initial PHY setting */ writel (0x20c , port +PORT_PHY_CFG ); +/* Configure IRQ WoC */ +if (probe_ent->host_flags &SIL24_FLAG_PCIX_IRQ_WOC ) +writel (PORT_CS_IRQ_WOC , port +PORT_CTRL_STAT ); +else +writel (PORT_CS_IRQ_WOC , port +PORT_CTRL_CLR ); +/* Clear port RST */ tmp =readl (port +PORT_CTRL_STAT );if (tmp &PORT_CS_PORT_RST ) {
Signature · 1 line
1.2.4
PATCH 7/13 sata_sil24: implement sil24_init_port()
In reply to Tejun HeoImplement sil24_init_port which performs port initialization via PORT_CS_INIT. To be used later by softreset and EH.
---
drivers/scsi/sata_sil24.c | 16 ++++++++++++++++ 1 files changed, 16 insertions(+), 0 deletions(-)
85433646e8335528b6cd754efa8c8b9607c6c340
drivers/scsi/sata_sil24.c +16 -0
@@ -438,6 +438,22 @@ static void sil24_tf_read(struct ata_por *tf = pp->tf; } +static int sil24_init_port (struct ata_port *ap) +{ +void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; +u32 tmp; + +writel (PORT_CS_INIT , port +PORT_CTRL_STAT ); +ata_wait_register (port +PORT_CTRL_STAT , +PORT_CS_INIT ,PORT_CS_INIT ,10 ,100 ); + tmp =ata_wait_register (port +PORT_CTRL_STAT , +PORT_CS_RDY ,0 ,10 ,100 ); + +if ((tmp & (PORT_CS_INIT |PORT_CS_RDY )) !=PORT_CS_RDY ) +return -EIO ; +return 0 ; +} +static int sil24_softreset (struct ata_port *ap,unsigned int *class) {void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr;
Signature · 1 line
1.2.4
PATCH 8/13 sata_sil24: put port into known state before softresetting
In reply to Tejun HeoMake sure the controller has no pending commands and ready for command before issuing SRST.
---
drivers/scsi/sata_sil24.c | 6 ++++++ 1 files changed, 6 insertions(+), 0 deletions(-)
b2c3f8df81a80fae7e9c145a5b73939799c66447
drivers/scsi/sata_sil24.c +6 -0
@@ -475,6 +475,12 @@ static int sil24_softreset(struct ata_po irq_enable =readl (port +PORT_IRQ_ENABLE_SET );writel (irq_enable, port +PORT_IRQ_ENABLE_CLR ); +/* put the port into known state */ +if (sil24_init_port (ap)) { + reason ="port not ready" ; + goto err; + } +/* * XXX: Not sure whether the following sleep is needed or not. * The original driver had it. So....
Signature · 1 line
1.2.4
PATCH 9/13 sata_sil24: kill 10ms sleep in softreset
In reply to Tejun HeoNothing, not the datasheet nor the errats, says this delay is necessary and with the previous PORT_CS_INIT change, we know the controller is in good state. Kill 10ms sleep.
---
drivers/scsi/sata_sil24.c | 7 +------ 1 files changed, 1 insertions(+), 6 deletions(-)
2963e81690dadcb59329709422d7b6c2e22f53e0
drivers/scsi/sata_sil24.c +1 -6
@@ -481,12 +481,7 @@ static int sil24_softreset(struct ata_po goto err; } -/* -* XXX: Not sure whether the following sleep is needed or not. -* The original driver had it. So.... -*/ -msleep (10 ); - +/* do SRST */ prb->ctrl =PRB_CTRL_SRST ; prb->fis[1 ] =0 ;/* no PM yet */
Signature · 1 line
1.2.4
PATCH 10/13 sata_sil24: reimplement hardreset
In reply to Tejun HeoReimplement hardreset according to the datasheet. The old hardreset didn't reset controller status and the controller might not be ready after reset. Also, as SStatus is a bit flakey after hardreset, sata_std_hardrset() didn't use to wait long enough before proceeding.
Note that as we're not depending on SStatus, DET==1 condition cannot be used to wait for link, so use shorter timeout for no device case.
---
drivers/scsi/sata_sil24.c | 43 ++++++++++++++++++++++++++++++++++++++++--- 1 files changed, 40 insertions(+), 3 deletions(-)
241bde5ce7088b4beea4ebf8020a90247a3f4f9f
drivers/scsi/sata_sil24.c +40 -3
@@ -522,10 +522,47 @@ static int sil24_softreset(struct ata_postatic int sil24_hardreset (struct ata_port *ap,unsigned int *class) { -unsigned int dummy_class; +void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr; +const char *reason; +int tout_msec; +u32 tmp; + +/* sil24 does the right thing(tm) without any protection */ +ata_set_sata_spd (ap); + + tout_msec =100 ; +if (sata_dev_present (ap)) + tout_msec =5000 ; + +writel (PORT_CS_DEV_RST , port +PORT_CTRL_STAT ); + tmp =ata_wait_register (port +PORT_CTRL_STAT , +PORT_CS_DEV_RST ,PORT_CS_DEV_RST ,10 , tout_msec); + +/* SStatus oscillates between zero and valid status for short +* duration after DEV_RST, give it time to settle. +*/ +msleep (100 ); + +if (tmp &PORT_CS_DEV_RST ) { +if (!sata_dev_present (ap)) +return 0 ; + reason ="link not ready" ; + goto err; + } + +if (ata_busy_sleep (ap,ATA_TMOUT_BOOT_QUICK ,ATA_TMOUT_BOOT )) { + reason ="device not ready" ; + goto err; + } + +/* sil24 doesn't report device class code after hardreset, +* leave *class alone. +*/ +return 0 ; -/* sil24 doesn't report device signature after hard reset */ -return sata_std_hardreset (ap, &dummy_class); + err: +printk (KERN_ERR "ata%u: hardreset failed (%s)\n" , ap->id, reason); +return -EIO ; }static int sil24_probe_reset (struct ata_port *ap,unsigned int *classes)
Signature · 1 line
1.2.4
PATCH 11/13 sata_sil24: don't do hardreset during driver initialization
In reply to Tejun HeoThere's no need to perform hardreset during driver initialization. It's already done during host reset and even if the controller is in some wacky state, we now have proper hardreset to back us up.
---
drivers/scsi/sata_sil24.c | 5 ----- 1 files changed, 0 insertions(+), 5 deletions(-)
37a3de1972e581e9a1609be875720bb0f9a3f455
drivers/scsi/sata_sil24.c +0 -5
@@ -1070,11 +1070,6 @@ static int sil24_init_one(struct pci_dev/* Clear port multiplier enable and resume bits */ writel (PORT_CS_PM_EN |PORT_CS_RESUME , port +PORT_CTRL_CLR ); - -/* Reset itself */ -if (__sil24_reset_controller (port)) -dev_printk (KERN_ERR , &pdev->dev, -"failed to reset controller\n" ); }/* Turn on interrupts */
Signature · 1 line
1.2.4
PATCH 12/13 sata_sil24: fix on-memory structure byteorder
In reply to Tejun HeoData structures residing on memory and fetched by the controller should have LE ordering. Fix it.
---
drivers/scsi/sata_sil24.c | 13 ++++++------- 1 files changed, 6 insertions(+), 7 deletions(-)
c65a82b53f25bf7ef1c5d08d65c34770fd5bc55c
drivers/scsi/sata_sil24.c +6 -7
@@ -482,7 +482,7 @@ static int sil24_softreset(struct ata_po }/* do SRST */ - prb->ctrl =PRB_CTRL_SRST ; + prb->ctrl =cpu_to_le16 (PRB_CTRL_SRST ); prb->fis[1 ] =0 ;/* no PM yet */ writel ((u32 )paddr, port +PORT_CMD_ACTIVATE );
@@ -598,6 +598,7 @@ static void sil24_qc_prep(struct ata_queunion sil24_cmd_block *cb = pp->cmd_block + qc->tag;struct sil24_prb *prb;struct sil24_sge *sge; +u16 ctrl =0 ;switch (qc->tf.protocol) {case ATA_PROT_PIO :
@@ -605,7 +606,6 @@ static void sil24_qc_prep(struct ata_quecase ATA_PROT_NODATA : prb = &cb->ata.prb; sge = cb->ata.sge; - prb->ctrl =0 ;break ;case ATA_PROT_ATAPI :
@@ -618,12 +618,10 @@ static void sil24_qc_prep(struct ata_queif (qc->tf.protocol !=ATA_PROT_ATAPI_NODATA ) {if (qc->tf.flags &ATA_TFLAG_WRITE ) - prb->ctrl =PRB_CTRL_PACKET_WRITE ; + ctrl =PRB_CTRL_PACKET_WRITE ;else - prb->ctrl =PRB_CTRL_PACKET_READ ; - }else - prb->ctrl =0 ; - + ctrl =PRB_CTRL_PACKET_READ ; + }break ;default :
@@ -632,6 +630,7 @@ static void sil24_qc_prep(struct ata_queBUG (); } + prb->ctrl =cpu_to_le16 (ctrl);ata_tf_to_fis (&qc->tf, prb->fis,0 );if (qc->flags &ATA_QCFLAG_DMAMAP )
Signature · 1 line
1.2.4
PATCH 13/13 sata_sil24: enable 64bit
In reply to Tejun HeoEnable 64bit.
---
drivers/scsi/sata_sil24.c | 47 +++++++++++++++++++++++++++------------------ 1 files changed, 28 insertions(+), 19 deletions(-)
96079f923aa282ccd853e1fcd71f289568384bd8
drivers/scsi/sata_sil24.c +28 -19
@@ -486,6 +486,7 @@ static int sil24_softreset(struct ata_po prb->fis[1 ] =0 ;/* no PM yet */ writel ((u32 )paddr, port +PORT_CMD_ACTIVATE ); +writel ((u64 )paddr >>32 , port +PORT_CMD_ACTIVATE +4 ); mask = (PORT_IRQ_COMPLETE |PORT_IRQ_ERROR ) <<PORT_IRQ_RAW_SHIFT ; irq_stat = ata_wait_register(port + PORT_IRQ_STAT, mask, 0x0,
@@ -645,6 +646,8 @@ static unsigned int sil24_qc_issue(strucdma_addr_t paddr = pp->cmd_block_dma + qc->tag *sizeof (*pp->cmd_block);writel ((u32 )paddr, port +PORT_CMD_ACTIVATE ); +writel ((u64 )paddr >>32 , port +PORT_CMD_ACTIVATE +4 ); +return 0 ; }
@@ -981,22 +984,29 @@ static int sil24_init_one(struct pci_dev/* * Configure the device */ -/* -* FIXME: This device is certainly 64-bit capable. We just -* don't know how to use it. After fixing 32bit activation in -* this function, enable 64bit masks here. -*/ - rc =pci_set_dma_mask (pdev,DMA_32BIT_MASK ); -if (rc) { -dev_printk (KERN_ERR , &pdev->dev, -"32-bit DMA enable failed\n" ); - goto out_free; - } - rc =pci_set_consistent_dma_mask (pdev,DMA_32BIT_MASK ); -if (rc) { -dev_printk (KERN_ERR , &pdev->dev, -"32-bit consistent DMA enable failed\n" ); - goto out_free; +if (!pci_set_dma_mask (pdev,DMA_64BIT_MASK )) { + rc =pci_set_consistent_dma_mask (pdev,DMA_64BIT_MASK ); +if (rc) { + rc =pci_set_consistent_dma_mask (pdev,DMA_32BIT_MASK ); +if (rc) { +dev_printk (KERN_ERR , &pdev->dev, +"64-bit DMA enable failed\n" ); + goto out_free; + } + } + }else { + rc =pci_set_dma_mask (pdev,DMA_32BIT_MASK ); +if (rc) { +dev_printk (KERN_ERR , &pdev->dev, +"32-bit DMA enable failed\n" ); + goto out_free; + } + rc =pci_set_consistent_dma_mask (pdev,DMA_32BIT_MASK ); +if (rc) { +dev_printk (KERN_ERR , &pdev->dev, +"32-bit consistent DMA enable failed\n" ); + goto out_free; + } }/* GPIO off */
@@ -1054,9 +1064,8 @@ static int sil24_init_one(struct pci_devwritel (0x0000 , port +PORT_CRC_ERR_CNT );writel (0x0000 , port +PORT_HSHK_ERR_CNT ); -/* FIXME: 32bit activation? */ -writel (0 , port +PORT_ACTIVATE_UPPER_ADDR ); -writel (PORT_CS_32BIT_ACTV , port +PORT_CTRL_STAT ); +/* Always use 64bit activation */ +writel (PORT_CS_32BIT_ACTV , port +PORT_CTRL_CLR );/* Configure interrupts */ writel (0xffff , port +PORT_IRQ_ENABLE_CLR );
Signature · 1 line
1.2.4
PATCH 6/13 sata_sil24: implement loss of completion interrupt on PCI-X errta fix
In reply to Tejun HeoSiI3124 might lose completion interrupt if completion interrupt occurs shortly after SLOT_STAT register is read for the previous completion interrupt if it is operating in PCI-X mode.
This currently doesn't trigger as libata never queues more than one command, but it will with NCQ changes. This patch implements the workaround - turning on WoC and explicitly clearing interrupt.
---
Unlike PHY configuration WoC configuration should be done _after_ port reset is turned off. The patch is updated such that WoC conf comes below clearing port rst. This update doesn't disturb other patches.
drivers/scsi/sata_sil24.c | 27 +++++++++++++++++++++++++-- 1 files changed, 25 insertions(+), 2 deletions(-)
66942efc5890c71878ade3268862fcd3611c3cb5
drivers/scsi/sata_sil24.c +25 -2
@@ -221,6 +221,7 @@ enum {/* host flags */ SIL24_COMMON_FLAGS =ATA_FLAG_SATA |ATA_FLAG_NO_LEGACY |ATA_FLAG_MMIO |ATA_FLAG_PIO_DMA , +SIL24_FLAG_PCIX_IRQ_WOC = (1 <<24 ),/* IRQ loss errata on PCI-X */ IRQ_STAT_4PORTS = 0xf, };
@@ -349,7 +350,8 @@ static struct ata_port_info sil24_port_i/* sil_3124 */ { .sht = &sil24_sht, - .host_flags = SIL24_COMMON_FLAGS | SIL24_NPORTS2FLAG(4), + .host_flags =SIL24_COMMON_FLAGS |SIL24_NPORTS2FLAG (4 ) | + SIL24_FLAG_PCIX_IRQ_WOC, .pio_mask = 0x1f, /* pio0-4 */ .mwdma_mask = 0x07, /* mwdma0-2 */ .udma_mask = 0x3f, /* udma0-5 */
@@ -738,6 +740,10 @@ static inline void sil24_host_intr(struc slot_stat =readl (port +PORT_SLOT_STAT );if (!(slot_stat &HOST_SSTAT_ATTN )) {struct sil24_port_priv *pp = ap->private_data; + +if (ap->flags &SIL24_FLAG_PCIX_IRQ_WOC ) +writel (PORT_IRQ_COMPLETE , port +PORT_IRQ_STAT ); +/* * !HOST_SSAT_ATTN guarantees successful completion, * so reading back tf registers is unnecessary for
@@ -869,6 +875,7 @@ static int sil24_init_one(struct pci_devvoid __iomem *host_base =NULL ;void __iomem *port_base =NULL ;int i, rc; +u32 tmp;if (!printed_version++)dev_printk (KERN_DEBUG , &pdev->dev,"version " DRV_VERSION "\n" );
@@ -942,13 +949,23 @@ static int sil24_init_one(struct pci_dev/* GPIO off */ writel (0 , host_base +HOST_FLASH_CMD ); +/* Apply workaround for completion IRQ loss on PCI-X errata */ +if (probe_ent->host_flags &SIL24_FLAG_PCIX_IRQ_WOC ) { + tmp =readl (host_base +HOST_CTRL ); +if (tmp & (HOST_CTRL_TRDY |HOST_CTRL_STOP |HOST_CTRL_DEVSEL )) +dev_printk (KERN_INFO , &pdev->dev, +"Applying completion IRQ loss on PCI-X " +"errata fix\n" ); +else + probe_ent->host_flags &= ~SIL24_FLAG_PCIX_IRQ_WOC ; + } +/* clear global reset & mask interrupts during initialization */ writel (0 , host_base +HOST_CTRL );for (i =0 ; i < probe_ent->n_ports; i++) {void __iomem *port = port_base + i *PORT_REGS_SIZE ;unsigned long portu = (unsigned long )port; -u32 tmp; probe_ent->port[i].cmd_addr = portu +PORT_PRB ; probe_ent->port[i].scr_addr = portu +PORT_SCONTROL ;
@@ -970,6 +987,12 @@ static int sil24_init_one(struct pci_dev "failed to clear port RST\n"); } +/* Configure IRQ WoC */ +if (probe_ent->host_flags &SIL24_FLAG_PCIX_IRQ_WOC ) +writel (PORT_CS_IRQ_WOC , port +PORT_CTRL_STAT ); +else +writel (PORT_CS_IRQ_WOC , port +PORT_CTRL_CLR ); +/* Zero error counters. */ writel (0x8000 , port +PORT_DECODE_ERR_THRESH );writel (0x8000 , port +PORT_CRC_ERR_THRESH );
Signature · 1 line
1.2.4
Re: [PATCH 06/13 (updated)] sata_sil24: implement loss of completion interrupt on PCI-X errta fix
Please ignore this whole patchset. I'll repost soon. Sorry about the noise.
Signature · 1 line
tejun