misc reset updates (repost)
PATCH 1/1 misc reset updates (repost)
Hello, all.
This is repost of misc-reset-updates patchset. Previous posting didn't have proper head message and patch numbers were incorrect. This repost is to reduce the amount of confusion.
This patchset updates reset mechanism. Cable type is set early in probeinit, @verbose argument is removed from reset methods and missing error messages are added.
This patchset is against
upstream (c2a6585296009379e0f4eff39cdcb108b457ebf2)
Thanks.
--
tejun
PATCH 3/3 libata: make reset methods complain when they fail
Make reset methods complain loud when they fail.
---
drivers/scsi/libata-core.c | 8 +++++--- drivers/scsi/sata_sil24.c | 2 +- 2 files changed, 6 insertions(+), 4 deletions(-)
3bf1cd4f285525deb2381a6f9d625a0f25007899
drivers/scsi/libata-core.c +5 -3
@@ -2232,8 +2232,10 @@ static unsigned int ata_bus_softreset(st* the bus shows 0xFF because the odd clown forgets the D7 * pulldown resistor. */ -if (ata_check_status (ap) ==0xFF ) +if (ata_check_status (ap) ==0xFF ) { +printk (KERN_ERR "ata%u: SRST failed (status 0xFF)\n" , ap->id);return AC_ERR_OTHER ; + }ata_bus_post_reset (ap, devmask);
@@ -2494,8 +2496,8 @@ int sata_std_hardreset(struct ata_port * }if (ata_busy_sleep (ap,ATA_TMOUT_BOOT_QUICK ,ATA_TMOUT_BOOT )) { -printk (KERN_ERR "ata%u: COMRESET failed " -"(device not ready)\n" , ap->id); +printk (KERN_ERR +"ata%u: COMRESET failed (device not ready)\n" , ap->id);return -EIO ; }
drivers/scsi/sata_sil24.c +1 -1
@@ -474,7 +474,7 @@ static int sil24_softreset(struct ata_powritel (irq_enable, port +PORT_IRQ_ENABLE_SET );if (!(irq_stat &PORT_IRQ_COMPLETE )) { -DPRINTK ("EXIT, srst failed\n" ); +printk (KERN_ERR "ata%u: softreset failed (timeout)\n" , ap->id);return -EIO ; }
Signature · 1 line
1.2.4
PATCH 2/3 libata: kill @verbose from ata_reset_fn_t
In reply to Tejun Heo@verbose was added to ata_reset_fn_t because AHCI complained during probing if no device was attached to the port. However, muting failure message isn't the correct approach. Reset methods are responsible for detecting no device condition and finishing successfully. Now that AHCI softreset is fixed, kill @verbose.
---
drivers/scsi/ahci.c | 13 +++++-------- drivers/scsi/libata-core.c | 36 ++++++++++++------------------------ drivers/scsi/libata.h | 6 ++---- drivers/scsi/sata_sil24.c | 8 +++----- include/linux/libata.h | 8 +++----- 5 files changed, 25 insertions(+), 46 deletions(-)
ec5e2b0375c15dce9eb83607ddf9864bfb20bc85
drivers/scsi/ahci.c +5 -8
@@ -535,7 +535,7 @@ static int ahci_poll_register(void __iomreturn -1 ; } -static int ahci_softreset (struct ata_port *ap,int verbose,unsigned int *class) +static int ahci_softreset (struct ata_port *ap,unsigned int *class) {struct ahci_host_priv *hpriv = ap->host_set->private_data;struct ahci_port_priv *pp = ap->private_data;
@@ -647,22 +647,19 @@ static int ahci_softreset(struct ata_por fail_restart:ahci_start_engine (ap); fail: -if (verbose) -printk (KERN_ERR "ata%u: softreset failed (%s)\n" , - ap->id, reason); -else -DPRINTK ("EXIT, rc=%d reason=\"%s\"\n" , rc, reason); +printk (KERN_ERR "ata%u: softreset failed (%s)\n" , + ap->id, reason);return rc; } -static int ahci_hardreset (struct ata_port *ap,int verbose,unsigned int *class) +static int ahci_hardreset (struct ata_port *ap,unsigned int *class) {int rc;DPRINTK ("ENTER\n" );ahci_stop_engine (ap); - rc =sata_std_hardreset (ap, verbose, class); + rc =sata_std_hardreset (ap, class);ahci_start_engine (ap);if (rc ==0 )
drivers/scsi/libata-core.c +12 -24
@@ -2387,7 +2387,6 @@ void ata_std_probeinit(struct ata_port */** * ata_std_softreset - reset host port via ATA SRST * @ap: port to reset -* @verbose: fail verbosely * @classes: resulting classes of attached devices * * Reset host port using ATA SRST. This function is to be used
@@ -2399,7 +2398,7 @@ void ata_std_probeinit(struct ata_port ** RETURNS: * 0 on success, -errno otherwise. */ -int ata_std_softreset (struct ata_port *ap,int verbose,unsigned int *classes) +int ata_std_softreset (struct ata_port *ap,unsigned int *classes) {unsigned int slave_possible = ap->flags &ATA_FLAG_SLAVE_POSS ;unsigned int devmask =0 , err_mask;
@@ -2425,12 +2424,8 @@ int ata_std_softreset(struct ata_port *aDPRINTK ("about to softreset, devmask=%x\n" , devmask); err_mask =ata_bus_softreset (ap, devmask);if (err_mask) { -if (verbose) -printk (KERN_ERR "ata%u: SRST failed (err_mask=0x%x)\n" , - ap->id, err_mask); -else -DPRINTK ("EXIT, softreset failed (err_mask=0x%x)\n" , - err_mask); +printk (KERN_ERR "ata%u: SRST failed (err_mask=0x%x)\n" , + ap->id, err_mask);return -EIO ; }
@@ -2447,7 +2442,6 @@ int ata_std_softreset(struct ata_port *a/** * sata_std_hardreset - reset host port via SATA phy reset * @ap: port to reset -* @verbose: fail verbosely * @class: resulting class of attached device * * SATA phy-reset host port using DET bits of SControl register.
@@ -2460,7 +2454,7 @@ int ata_std_softreset(struct ata_port *a* RETURNS: * 0 on success, -errno otherwise. */ -int sata_std_hardreset (struct ata_port *ap,int verbose,unsigned int *class) +int sata_std_hardreset (struct ata_port *ap,unsigned int *class) {u32 scontrol;
@@ -2500,11 +2494,8 @@ int sata_std_hardreset(struct ata_port * }if (ata_busy_sleep (ap,ATA_TMOUT_BOOT_QUICK ,ATA_TMOUT_BOOT )) { -if (verbose) -printk (KERN_ERR "ata%u: COMRESET failed " -"(device not ready)\n" , ap->id); -else -DPRINTK ("EXIT, device not ready\n" ); +printk (KERN_ERR "ata%u: COMRESET failed " +"(device not ready)\n" , ap->id);return -EIO ; }
@@ -2592,16 +2583,15 @@ int ata_std_probe_reset(struct ata_port ata_std_postreset, classes); } -int ata_do_reset (struct ata_port *ap, -ata_reset_fn_t reset,ata_postreset_fn_t postreset, -int verbose,unsigned int *classes) +int ata_do_reset (struct ata_port *ap,ata_reset_fn_t reset, +ata_postreset_fn_t postreset,unsigned int *classes) {int i, rc;for (i =0 ; i <ATA_MAX_DEVICES ; i++) classes[i] =ATA_DEV_UNKNOWN ; - rc =reset (ap, verbose, classes); + rc =reset (ap, classes);if (rc)return rc;
@@ -2645,8 +2635,6 @@ int ata_do_reset(struct ata_port *ap,* - If classification is supported, fill classes[] with * recognized class codes. * - If classification is not supported, leave classes[] alone. -* - If verbose is non-zero, print error message on failure; -* otherwise, shut up. * * LOCKING: * Kernel thread context (may sleep)
@@ -2666,7 +2654,7 @@ int ata_drive_probe_reset(struct ata_porprobeinit (ap);if (softreset && !ata_set_sata_spd_needed (ap)) { - rc =ata_do_reset (ap, softreset, postreset,0 , classes); + rc =ata_do_reset (ap, softreset, postreset, classes);if (rc ==0 && classes[0 ] !=ATA_DEV_UNKNOWN ) goto done; printk(KERN_INFO "ata%u: softreset failed, will try "
@@ -2678,7 +2666,7 @@ int ata_drive_probe_reset(struct ata_por goto done;while (1 ) { - rc =ata_do_reset (ap, hardreset, postreset,0 , classes); + rc =ata_do_reset (ap, hardreset, postreset, classes);if (rc ==0 ) {if (classes[0 ] !=ATA_DEV_UNKNOWN ) goto done;
@@ -2699,7 +2687,7 @@ int ata_drive_probe_reset(struct ata_por ap->id);ssleep (5 ); - rc =ata_do_reset (ap, softreset, postreset,0 , classes); + rc =ata_do_reset (ap, softreset, postreset, classes); } done:
drivers/scsi/libata.h +2 -4
@@ -56,10 +56,8 @@ extern int ata_set_sata_spd_needed(strucextern int ata_down_xfermask_limit (struct ata_port *ap,struct ata_device *dev,int force_pio0);extern int ata_set_mode (struct ata_port *ap,struct ata_device **r_failed_dev); -extern int ata_do_reset (struct ata_port *ap, -ata_reset_fn_t reset, -ata_postreset_fn_t postreset, -int verbose,unsigned int *classes); +extern int ata_do_reset (struct ata_port *ap,ata_reset_fn_t reset, +ata_postreset_fn_t postreset,unsigned int *classes);extern void ata_qc_free (struct ata_queued_cmd *qc);extern void ata_qc_issue (struct ata_queued_cmd *qc);extern int ata_check_atapi_dma (struct ata_queued_cmd *qc);
drivers/scsi/sata_sil24.c +3 -5
@@ -427,8 +427,7 @@ static void sil24_tf_read(struct ata_por *tf = pp->tf; } -static int sil24_softreset (struct ata_port *ap,int verbose, -unsigned int *class) +static int sil24_softreset (struct ata_port *ap,unsigned int *class) {void __iomem *port = (void __iomem *)ap->ioaddr.cmd_addr;struct sil24_port_priv *pp = ap->private_data;
@@ -490,13 +489,12 @@ static int sil24_softreset(struct ata_poreturn 0 ; } -static int sil24_hardreset (struct ata_port *ap,int verbose, -unsigned int *class) +static int sil24_hardreset (struct ata_port *ap,unsigned int *class) {unsigned int dummy_class;/* sil24 doesn't report device signature after hard reset */ -return sata_std_hardreset (ap, verbose, &dummy_class); +return sata_std_hardreset (ap, &dummy_class); }static int sil24_probe_reset (struct ata_port *ap,unsigned int *classes)
include/linux/libata.h +3 -5
@@ -251,7 +251,7 @@ struct ata_queued_cmd;/* typedefs */ typedef void (*ata_qc_cb_t ) (struct ata_queued_cmd *qc);typedef void (*ata_probeinit_fn_t )(struct ata_port *); -typedef int (*ata_reset_fn_t )(struct ata_port *,int ,unsigned int *); +typedef int (*ata_reset_fn_t )(struct ata_port *,unsigned int *);typedef void (*ata_postreset_fn_t )(struct ata_port *ap,unsigned int *);struct ata_ioports {
@@ -508,10 +508,8 @@ extern int ata_drive_probe_reset(struct ata_reset_fn_t softreset, ata_reset_fn_t hardreset, ata_postreset_fn_t postreset, unsigned int *classes);extern void ata_std_probeinit (struct ata_port *ap); -extern int ata_std_softreset (struct ata_port *ap,int verbose, -unsigned int *classes); -extern int sata_std_hardreset (struct ata_port *ap,int verbose, -unsigned int *class); +extern int ata_std_softreset (struct ata_port *ap,unsigned int *classes); +extern int sata_std_hardreset (struct ata_port *ap,unsigned int *class);extern void ata_std_postreset (struct ata_port *ap,unsigned int *classes);extern int ata_dev_revalidate (struct ata_port *ap,struct ata_device *dev,int post_reset);
Signature · 1 line
1.2.4
PATCH 1/3 libata: set default cbl in probeinit
In reply to Tejun HeoMake setting CBL type responsibility of probeinit. This allows using only ap->cbl == ATA_CBL_SATA test in all other parts. Without this, ata_down_sata_spd_limit() doesn't work during probe reset.
---
drivers/scsi/libata-core.c | 10 +++++----- 1 files changed, 5 insertions(+), 5 deletions(-)
8e8d8e326ca269f1cf38c6cf715a71a98e773600
drivers/scsi/libata-core.c +5 -5
@@ -2369,12 +2369,16 @@ void ata_std_probeinit(struct ata_port *if ((ap->flags &ATA_FLAG_SATA ) && ap->ops->scr_read) {u32 spd; +/* set cable type and resume link */ + ap->cbl =ATA_CBL_SATA ;sata_phy_resume (ap); +/* init sata_spd_limit to the current value */ spd = (scr_read (ap,SCR_CONTROL ) &0xf0 ) >>4 ;if (spd) ap->sata_spd_limit &= (1 << spd) -1 ; +/* wait for device */ if (sata_dev_present (ap))ata_busy_sleep (ap,ATA_TMOUT_BOOT_QUICK ,ATA_TMOUT_BOOT ); }
@@ -2531,10 +2535,6 @@ void ata_std_postreset(struct ata_port * {DPRINTK ("ENTER\n" ); -/* set cable type if it isn't already set */ -if (ap->cbl ==ATA_CBL_NONE && ap->flags &ATA_FLAG_SATA ) - ap->cbl =ATA_CBL_SATA ; -/* print link status */ if (ap->cbl ==ATA_CBL_SATA )sata_print_link_status (ap);
@@ -2584,7 +2584,7 @@ int ata_std_probe_reset(struct ata_portata_reset_fn_t hardreset; hardreset =NULL ; -if (ap->flags &ATA_FLAG_SATA && ap->ops->scr_read) +if (ap->cbl ==ATA_CBL_SATA && ap->ops->scr_read) hardreset = sata_std_hardreset; return ata_drive_probe_reset(ap, ata_std_probeinit,
Signature · 1 line
1.2.4
Re: [PATCHSET 1/9] this is the first patchset
In reply to Tejun Heonada
--
tejun
Re: [PATCH 1/3] libata: set default cbl in probeinit
In reply to Tejun HeoQuoted 5 lines · Tejun Heo
Make setting CBL type responsibility of probeinit. This allows using only
ap->cbl==ATA_CBL_SATAtest in all other parts. Without this,ata_down_sata_spd_limit()doesn't work during probe reset.Signed-off-by Tejun Heo <[email protected]>
applied 1-3