Skip to contentSkip to conversation

tg3: Add phy workaround

PATCH Applied Michael Chan 2 participants 2 messages Apr 29, 2006 – Apr 30, 2006

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 2/6 tg3: Add phy workaround

Add some PHY workaround code to reduce jitter on some PHYs.

drivers/net/tg3.c +13 -4
index a28accb..a307340 100644
@@ -1030,6 +1030,12 @@ out:
 		tg3_writephy(tp, MII_TG3_DSP_RW_PORT, 0x14e2);
 		tg3_writephy(tp, MII_TG3_AUX_CTRL, 0x0400);
 	}
+	else if (tp->tg3_flags2 & TG3_FLG2_PHY_JITTER_BUG) {
+		tg3_writephy(tp, MII_TG3_AUX_CTRL, 0x0c00);
+		tg3_writephy(tp, MII_TG3_DSP_ADDRESS, 0x000a);
+		tg3_writephy(tp, MII_TG3_DSP_RW_PORT, 0x010b);
+		tg3_writephy(tp, MII_TG3_AUX_CTRL, 0x0400);
+	}
 	/* Set Extended packet length bit (bit 14) on all chips that */
 	/* support jumbo frames */
 	if ((tp->phy_id & PHY_ID_MASK) == PHY_ID_BCM5401) {
@@ -10360,10 +10366,13 @@ static int __devinit tg3_get_invariants(
 	if (tp->pci_chip_rev_id == CHIPREV_ID_5704_A0)
 		tp->tg3_flags2 |= TG3_FLG2_PHY_5704_A0_BUG;
 
-	if ((tp->tg3_flags2 & TG3_FLG2_5705_PLUS) &&
-	    (GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5755) &&
-	    (GET_ASIC_REV(tp->pci_chip_rev_id) != ASIC_REV_5787))
-		tp->tg3_flags2 |= TG3_FLG2_PHY_BER_BUG;
+	if (tp->tg3_flags2 & TG3_FLG2_5705_PLUS) {
+		if (GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5755 ||
+		    GET_ASIC_REV(tp->pci_chip_rev_id) == ASIC_REV_5787)
+			tp->tg3_flags2 |= TG3_FLG2_PHY_JITTER_BUG;
+		else
+			tp->tg3_flags2 |= TG3_FLG2_PHY_BER_BUG;
+	}
 
 	tp->coalesce_mode = 0;
 	if (GET_CHIP_REV(tp->pci_chip_rev_id) != CHIPREV_5700_AX &&
drivers/net/tg3.h +1 -0
index 8c8b987..0e29b88 100644
@@ -2215,6 +2215,7 @@ struct tg3 {
 #define TG3_FLG2_HW_TSO_2		0x08000000
 #define TG3_FLG2_HW_TSO			(TG3_FLG2_HW_TSO_1 | TG3_FLG2_HW_TSO_2)
 #define TG3_FLG2_1SHOT_MSI		0x10000000
+#define TG3_FLG2_PHY_JITTER_BUG		0x20000000
 
 	u32				split_mode_max_reqs;
 #define SPLIT_MODE_5704_MAX_REQ		3
maintainer Applied
#1 lore raw

From: "Michael Chan" <[email protected]>
Date: Fri, 28 Apr 2006 16:35:19 -0700

Quoted 3 lines

Add some PHY workaround code to reduce jitter on some PHYs.

Applied, thanks.

It really bugs me that all of this indirect addressing into the DSP is done with magic addresses and register values. It would be great to get some defined in tg3.h that documented the DSP register set properly.