Skip to contentSkip to conversation

question about qlogic QLA2312

DISCUSSION Giuseppe Sacco 3 participants 4 messages Sep 15, 2006 SCSI

lore
Share & tools
lore
#0 lore raw

Hi all,
I installed a new machine with this SCSI controller

03:02.0 Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter (rev
02)

The problem is that firmware cannot be loaded on this board. When loading the qla2xxx driver, I get these messages:

QLogic Fibre Channel HBA Driver
ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 22 (level, low) -> IRQ 177 qla2xxx 0000:03:02.0: Found an ISP2312, irq 177, iobase 0xffffc20000f70000
qla2xxx 0000:03:02.0: Configuring PCI space...
qla2xxx 0000:03:02.0: Configure NVRAM parameters... qla2xxx 0000:03:02.0: Verifying loaded RISC code... qla2xxx 0000:03:02.0: Mailbox command timeout occured. Scheduling ISP abort.
qla2xxx 0000:03:02.0: [ERROR] Failed to load segment 0 of firmware qla2xxx 0000:03:02.0: Failed to initialize adapter
Trying to free free IRQ177

Browsing the archives of linux-scsi I found a solution[1]: a patch missing from the suse linux kernel. Sadly this was about an old versione of the kernel, while the current one already include it.

I am using kernel 2.6.16.21.

Any idea about what the problem could be?

Thanks,
Giuseppe

[1]http://www.spinics.net/lists/linux-scsi/msg06713.html

#1 lore raw

Which version of the driver are you using ?
Also, what is the version of the firmware ? You can get the version of fimware by

# grep FW_VERSION_STRING in the source directory.

It will be helpful if you could recompile the driver with QL_DEBUG_LEVEL_2 enabled (qla_dbg.h) and recreate the issue.

-Shyam

Quoted 40 lines · Giuseppe Sacco

Hi all,
I installed a new machine with this SCSI controller

03:02.0 Fibre Channel: QLogic Corp. QLA2312 Fibre Channel Adapter (rev
02)

The problem is that firmware cannot be loaded on this board. When loading the qla2xxx driver, I get these messages:

QLogic Fibre Channel HBA Driver
ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 22 (level, low) -> IRQ 177 qla2xxx 0000:03:02.0: Found an ISP2312, irq 177, iobase 0xffffc20000f70000
qla2xxx 0000:03:02.0: Configuring PCI space...
qla2xxx 0000:03:02.0: Configure NVRAM parameters... qla2xxx 0000:03:02.0: Verifying loaded RISC code... qla2xxx 0000:03:02.0: Mailbox command timeout occured. Scheduling ISP abort.
qla2xxx 0000:03:02.0: [ERROR] Failed to load segment 0 of firmware qla2xxx 0000:03:02.0: Failed to initialize adapter
Trying to free free IRQ177

Browsing the archives of linux-scsi I found a solution[1]: a patch missing from the suse linux kernel. Sadly this was about an old versione of the kernel, while the current one already include it.

I am using kernel 2.6.16.21.

Any idea about what the problem could be?

Thanks,
Giuseppe

[1]http://www.spinics.net/lists/linux-scsi/msg06713.html

-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

#2 lore raw

Il giorno ven, 15/09/2006 alle 19.26 +0530, G Shyam Sundar ha scritto:

Quoted 7 lines

Which version of the driver are you using ?
Also, what is the version of the firmware ? You can get the version of fimware by

# grep FW_VERSION_STRING in the source directory.

It will be helpful if you could recompile the driver with QL_DEBUG_LEVEL_2 enabled (qla_dbg.h) and recreate the issue.

I used two versions of the driver. The first one is shipped with the standard kernel from suse: 8.01.04-k (from modinfo). the second one is from the latest driver I could download from sourceforge.net (project linux-qla2xxx) and is version 8.01.06b2 (from modinfo).
The new version emit some more information:

qla2xxx_conf: module not supported by Novell, setting U taint flag.
qla2xxx: module not supported by Novell, setting U taint flag. QLogic Fibre Channel HBA Driver
qla2300: module not supported by Novell, setting U taint flag.
ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 22 (level, low) -> IRQ 177 qla2300 0000:03:02.0: Found an ISP2312, irq 177, iobase 0xffffc20000f70000
qla2300 0000:03:02.0: Configuring PCI space...
qla2300 0000:03:02.0: Configure NVRAM parameters... qla2300 0000:03:02.0: Verifying loaded RISC code... qla2300 0000:03:02.0: Mailbox command timeout occured. Scheduling ISP abort.
qla2300 0000:03:02.0: [ERROR] Failed to load segment 0 of firmware Mailbox registers:
scsi(7): mbox 0 0x4000
scsi(7): mbox 1 0xaaaa
scsi(7): mbox 2 0x5555
scsi(7): mbox 3 0xaa55
scsi(7): mbox 4 0x55aa
scsi(7): mbox 5 0xa5a5
qla2300 0000:03:02.0: Failed to initialize adapter
qla2300: probe of 0000:03:02.0 failed with error -1

About FW_VERSION_STRING:

lnx01:/usr/src/linux/drivers/scsi/qla2xxx # grep FW_V * ql2100_fw.c:#define FW_VERSION_STRING "1.19.25" ql2200_fw.c:#define FW_VERSION_STRING "2.02.08" ql2300_fw.c:#define FW_VERSION_STRING "3.03.18" ql2322_fw.c:#define FW_VERSION_STRING "3.03.18" ql2400_fw.c:#define FW_VERSION_STRING "4.00.16" ql6312_fw.c:#define FW_VERSION_STRING "3.03.18" lnx01:/usr/src/linux/drivers/scsi/qla2xxx #

Thanks,
Giuseppe

#3 lore raw
In reply to G Shyam Sundar

Il giorno ven, 15/09/2006 alle 19.26 +0530, G Shyam Sundar ha scritto:

Quoted 7 lines

Which version of the driver are you using ?
Also, what is the version of the firmware ? You can get the version of fimware by

# grep FW_VERSION_STRING in the source directory.

It will be helpful if you could recompile the driver with QL_DEBUG_LEVEL_2 enabled (qla_dbg.h) and recreate the issue.

Here it is, with some more debug levels (1,2,3, and 7)

Sep 15 17:49:01 lnx01 kernel: qla2xxx_conf: module not supported by Novell, setting U taint flag.
Sep 15 17:49:01 lnx01 kernel: qla2xxx: module not supported by Novell, setting U taint flag.
Sep 15 17:49:01 lnx01 kernel: QLogic Fibre Channel HBA Driver
Sep 15 17:49:01 lnx01 kernel: qla2300: module not supported by Novell, setting U taint flag.
Sep 15 17:49:01 lnx01 kernel: ACPI: PCI Interrupt 0000:03:02.0[A] -> GSI 22 (level, low) -> IRQ 177
Sep 15 17:49:01 lnx01 kernel: qla2300 0000:03:02.0: Found an ISP2312, irq 177, iobase 0xffffc20000f72000
Sep 15 17:49:01 lnx01 kernel: qla2300 0000:03:02.0: Configuring PCI space...
Sep 15 17:49:01 lnx01 kernel: qla2x00_get_flash_version(): read BIOS 1.47.
Sep 15 17:49:01 lnx01 kernel: qla2300 0000:03:02.0: Configure NVRAM parameters...
Sep 15 17:49:01 lnx01 kernel: qla2300 0000:03:02.0: Verifying loaded RISC code...
Sep 15 17:49:01 lnx01 kernel: scsi(11): Testing device at ffffc20000f72000.
Sep 15 17:49:01 lnx01 kernel: scsi(11): Reset register cleared by chip reset
Sep 15 17:49:01 lnx01 kernel: scsi(11): Checking product ID of chip
Sep 15 17:49:01 lnx01 kernel: scsi(11): Checking mailboxes.
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): Loaded MBX registers (displayed in bytes) = 
Sep 15 17:49:01 lnx01 kernel:  0   1   2   3   4   5   6   7   8   9  Ah  Bh  Ch  Dh  Eh  Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: 06  00  aa  aa  55  55  55  aa  aa  55  a5  a5  5a  5a  25  25
Sep 15 17:49:01 lnx01 kernel: 
Sep 15 17:49:01 lnx01 kernel:  0   1   2   3   4   5   6   7   8   9  Ah  Bh  Ch  Dh  Eh  Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: 20  50  f7  00  00  00  00  00  08  00  00  80  00  00  00  00
Sep 15 17:49:01 lnx01 kernel: 
Sep 15 17:49:01 lnx01 kernel:  0   1   2   3   4   5   6   7   8   9  Ah  Bh  Ch  Dh  Eh  Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: 53  49  f7  00  00  00  00  00  
Sep 15 17:49:01 lnx01 kernel: 
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): I/O address = ffffc20000f72080.
Sep 15 17:49:01 lnx01 kernel: Mailbox registers:
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 0 0x0000 
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 1 0x4953 
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 2 0x5020 
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 3 0x2020 
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 4 0x0002 
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 5 0x0004 
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): cmd=6 POLLING MODE.
Sep 15 17:49:01 lnx01 kernel: qla2x00_mbx_completion(11): Got mailbox completion. cmd=6.
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): cmd 6 completed.
Sep 15 17:49:01 lnx01 kernel: scsi(11): Loading risc segment@ addr ffffffff8836fc40, number of bytes 0x8000, offset 0x800.
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): Loaded MBX registers (displayed in bytes) = 
Sep 15 17:49:01 lnx01 kernel:  0   1   2   3   4   5   6   7   8   9  Ah  Bh  Ch  Dh  Eh  Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: 09  00  00  08  78  fc  00  00  00  80  00  00  00  00  01  00
Sep 15 17:49:01 lnx01 kernel: 
Sep 15 17:49:01 lnx01 kernel:  0   1   2   3   4   5   6   7   8   9  Ah  Bh  Ch  Dh  Eh  Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: b8  3a  da  f3  01  81  ff  ff  f8  39  da  f3  01  81  ff  ff
Sep 15 17:49:01 lnx01 kernel: 
Sep 15 17:49:01 lnx01 kernel:  0   1   2   3   4   5   6   7   8   9  Ah  Bh  Ch  Dh  Eh  Fh
Sep 15 17:49:01 lnx01 kernel: --------------------------------------------------------------
Sep 15 17:49:01 lnx01 kernel: 80  84  03  05  02  81  ff  ff  
Sep 15 17:49:01 lnx01 kernel: 
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): I/O address = ffffc20000f72080.
Sep 15 17:49:01 lnx01 kernel: Mailbox registers:
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 0 0x4000 
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 1 0xaaaa 
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 2 0x5555 
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 3 0xaa55 
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 4 0x55aa 
Sep 15 17:49:01 lnx01 kernel: scsi(11): mbox 5 0xa5a5 
Sep 15 17:49:01 lnx01 kernel: qla2x00_mailbox_command(11): cmd=9 POLLING MODE.
Sep 15 17:49:31 lnx01 kernel: qla2x00_mailbox_command(11): **** MB Command Timeout for cmd 9 ****
Sep 15 17:49:31 lnx01 kernel: qla2x00_mailbox_command(11): icontrol=0 jiffies=100055e49
Sep 15 17:49:31 lnx01 kernel: qla2x00_mailbox_command(11): *** mailbox[0] = 0x4000 ***
Sep 15 17:49:31 lnx01 kernel: Mailbox registers:
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 0 0x4000 
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 1 0xaaaa 
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 2 0x5555 
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 3 0xaa55 
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 4 0x55aa 
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 5 0xa5a5 
Sep 15 17:49:31 lnx01 kernel: qla2300 0000:03:02.0: Mailbox command timeout occured. Scheduling ISP abort.
Sep 15 17:49:31 lnx01 kernel: qla2300 0000:03:02.0: [ERROR] Failed to load segment 0 of firmware
Sep 15 17:49:31 lnx01 kernel: Mailbox registers:
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 0 0x4000 
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 1 0xaaaa 
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 2 0x5555 
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 3 0xaa55 
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 4 0x55aa 
Sep 15 17:49:31 lnx01 kernel: scsi(11): mbox 5 0xa5a5 
Sep 15 17:49:31 lnx01 kernel: qla2300 0000:03:02.0: Failed to initialize adapter
Sep 15 17:49:31 lnx01 kernel: qla2300: probe of 0000:03:02.0 failed with error -1