Skip to contentSkip to conversation

contents of sysfs branch

PATCH In review Len Brown 2 participants 21 messages Nov 24, 2006 – Dec 1, 2006

Subsystems (4)
lore
Share & tools
lore

Len Brown

author
#0 lore raw

The following patches are on the "sysfs" branch of the ACPI git tree.

To test, apply this e-mail series, or git pull from here:

git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6.git sysfs

I am hopeful that this series will settle down and make the test branch shortly, and thus make its way into an upcoming -mm release, and then upstream.

thanks,
-Len

author
#1 lore raw

PATCH 1/13 ACPI: clean up scan.c

From: Zhang Rui <[email protected]>

Adjust the code and make code doing similar things together. No logic changes.

---
 drivers/acpi/scan.c |  645 +++++++++++++++++++++++++--------------------------
 1 files changed, 316 insertions(+), 329 deletions(-)
drivers/acpi/scan.c +316 -329
index 698a154..e0255cb 100644
@@ -111,233 +111,6 @@ static struct kset acpi_namespace_kset =
 	.uevent_ops = &namespace_uevent_ops,
 };
 
-static void acpi_device_register(struct acpi_device *device,
-				 struct acpi_device *parent)
-{
-	int err;
-
-	/*
-	 * Linkage
-	 * -------
-	 * Link this device to its parent and siblings.
-	 */
-	INIT_LIST_HEAD(&device->children);
-	INIT_LIST_HEAD(&device->node);
-	INIT_LIST_HEAD(&device->g_list);
-	INIT_LIST_HEAD(&device->wakeup_list);
-
-	spin_lock(&acpi_device_lock);
-	if (device->parent) {
-		list_add_tail(&device->node, &device->parent->children);
-		list_add_tail(&device->g_list, &device->parent->g_list);
-	} else
-		list_add_tail(&device->g_list, &acpi_device_list);
-	if (device->wakeup.flags.valid)
-		list_add_tail(&device->wakeup_list, &acpi_wakeup_device_list);
-	spin_unlock(&acpi_device_lock);
-
-	strlcpy(device->kobj.name, device->pnp.bus_id, KOBJ_NAME_LEN);
-	if (parent)
-		device->kobj.parent = &parent->kobj;
-	device->kobj.ktype = &ktype_acpi_ns;
-	device->kobj.kset = &acpi_namespace_kset;
-	err = kobject_register(&device->kobj);
-	if (err < 0)
-		printk(KERN_WARNING "%s: kobject_register error: %d\n",
-			__FUNCTION__, err);
-	create_sysfs_device_files(device);
-}
-
-static void acpi_device_unregister(struct acpi_device *device, int type)
-{
-	spin_lock(&acpi_device_lock);
-	if (device->parent) {
-		list_del(&device->node);
-		list_del(&device->g_list);
-	} else
-		list_del(&device->g_list);
-
-	list_del(&device->wakeup_list);
-
-	spin_unlock(&acpi_device_lock);
-
-	acpi_detach_data(device->handle, acpi_bus_data_handler);
-	remove_sysfs_device_files(device);
-	kobject_unregister(&device->kobj);
-}
-
-void acpi_bus_data_handler(acpi_handle handle, u32 function, void *context)
-{
-
-	/* TBD */
-
-	return;
-}
-
-static int acpi_bus_get_power_flags(struct acpi_device *device)
-{
-	acpi_status status = 0;
-	acpi_handle handle = NULL;
-	u32 i = 0;
-
-
-	/*
-	 * Power Management Flags
-	 */
-	status = acpi_get_handle(device->handle, "_PSC", &handle);
-	if (ACPI_SUCCESS(status))
-		device->power.flags.explicit_get = 1;
-	status = acpi_get_handle(device->handle, "_IRC", &handle);
-	if (ACPI_SUCCESS(status))
-		device->power.flags.inrush_current = 1;
-
-	/*
-	 * Enumerate supported power management states
-	 */
-	for (i = ACPI_STATE_D0; i <= ACPI_STATE_D3; i++) {
-		struct acpi_device_power_state *ps = &device->power.states[i];
-		char object_name[5] = { '_', 'P', 'R', '0' + i, '\0' };
-
-		/* Evaluate "_PRx" to se if power resources are referenced */
-		acpi_evaluate_reference(device->handle, object_name, NULL,
-					&ps->resources);
-		if (ps->resources.count) {
-			device->power.flags.power_resources = 1;
-			ps->flags.valid = 1;
-		}
-
-		/* Evaluate "_PSx" to see if we can do explicit sets */
-		object_name[2] = 'S';
-		status = acpi_get_handle(device->handle, object_name, &handle);
-		if (ACPI_SUCCESS(status)) {
-			ps->flags.explicit_set = 1;
-			ps->flags.valid = 1;
-		}
-
-		/* State is valid if we have some power control */
-		if (ps->resources.count || ps->flags.explicit_set)
-			ps->flags.valid = 1;
-
-		ps->power = -1;	/* Unknown - driver assigned */
-		ps->latency = -1;	/* Unknown - driver assigned */
-	}
-
-	/* Set defaults for D0 and D3 states (always valid) */
-	device->power.states[ACPI_STATE_D0].flags.valid = 1;
-	device->power.states[ACPI_STATE_D0].power = 100;
-	device->power.states[ACPI_STATE_D3].flags.valid = 1;
-	device->power.states[ACPI_STATE_D3].power = 0;
-
-	/* TBD: System wake support and resource requirements. */
-
-	device->power.state = ACPI_STATE_UNKNOWN;
-
-	return 0;
-}
-
-int acpi_match_ids(struct acpi_device *device, char *ids)
-{
-	if (device->flags.hardware_id)
-		if (strstr(ids, device->pnp.hardware_id))
-			return 0;
-
-	if (device->flags.compatible_ids) {
-		struct acpi_compatible_id_list *cid_list = device->pnp.cid_list;
-		int i;
-
-		/* compare multiple _CID entries against driver ids */
-		for (i = 0; i < cid_list->count; i++) {
-			if (strstr(ids, cid_list->id[i].value))
-				return 0;
-		}
-	}
-	return -ENOENT;
-}
-
-static acpi_status
-acpi_bus_extract_wakeup_device_power_package(struct acpi_device *device,
-					     union acpi_object *package)
-{
-	int i = 0;
-	union acpi_object *element = NULL;
-
-	if (!device || !package || (package->package.count < 2))
-		return AE_BAD_PARAMETER;
-
-	element = &(package->package.elements[0]);
-	if (!element)
-		return AE_BAD_PARAMETER;
-	if (element->type == ACPI_TYPE_PACKAGE) {
-		if ((element->package.count < 2) ||
-		    (element->package.elements[0].type !=
-		     ACPI_TYPE_LOCAL_REFERENCE)
-		    || (element->package.elements[1].type != ACPI_TYPE_INTEGER))
-			return AE_BAD_DATA;
-		device->wakeup.gpe_device =
-		    element->package.elements[0].reference.handle;
-		device->wakeup.gpe_number =
-		    (u32) element->package.elements[1].integer.value;
-	} else if (element->type == ACPI_TYPE_INTEGER) {
-		device->wakeup.gpe_number = element->integer.value;
-	} else
-		return AE_BAD_DATA;
-
-	element = &(package->package.elements[1]);
-	if (element->type != ACPI_TYPE_INTEGER) {
-		return AE_BAD_DATA;
-	}
-	device->wakeup.sleep_state = element->integer.value;
-
-	if ((package->package.count - 2) > ACPI_MAX_HANDLES) {
-		return AE_NO_MEMORY;
-	}
-	device->wakeup.resources.count = package->package.count - 2;
-	for (i = 0; i < device->wakeup.resources.count; i++) {
-		element = &(package->package.elements[i + 2]);
-		if (element->type != ACPI_TYPE_ANY) {
-			return AE_BAD_DATA;
-		}
-
-		device->wakeup.resources.handles[i] = element->reference.handle;
-	}
-
-	return AE_OK;
-}
-
-static int acpi_bus_get_wakeup_device_flags(struct acpi_device *device)
-{
-	acpi_status status = 0;
-	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
-	union acpi_object *package = NULL;
-
-
-	/* _PRW */
-	status = acpi_evaluate_object(device->handle, "_PRW", NULL, &buffer);
-	if (ACPI_FAILURE(status)) {
-		ACPI_EXCEPTION((AE_INFO, status, "Evaluating _PRW"));
-		goto end;
-	}
-
-	package = (union acpi_object *)buffer.pointer;
-	status = acpi_bus_extract_wakeup_device_power_package(device, package);
-	if (ACPI_FAILURE(status)) {
-		ACPI_EXCEPTION((AE_INFO, status, "Extracting _PRW package"));
-		goto end;
-	}
-
-	kfree(buffer.pointer);
-
-	device->wakeup.flags.valid = 1;
-	/* Power button, Lid switch always enable wakeup */
-	if (!acpi_match_ids(device, "PNP0C0D,PNP0C0C,PNP0C0E"))
-		device->wakeup.flags.run_wake = 1;
-
-      end:
-	if (ACPI_FAILURE(status))
-		device->flags.wake_capable = 0;
-	return 0;
-}
-
 /* --------------------------------------------------------------------------
 		ACPI sysfs device file support
    -------------------------------------------------------------------------- */
@@ -447,20 +220,86 @@ acpi_eject_store(struct acpi_device *dev
 }
 
 /* --------------------------------------------------------------------------
-                              Performance Management
+			ACPI Bus operations
    -------------------------------------------------------------------------- */
+static inline struct acpi_device * to_acpi_dev(struct device * dev)
+{
+	return container_of(dev, struct acpi_device, dev);
+}
 
-static int acpi_bus_get_perf_flags(struct acpi_device *device)
+static int root_suspend(struct acpi_device * acpi_dev, pm_message_t state)
 {
-	device->performance.state = ACPI_STATE_UNKNOWN;
+	struct acpi_device * dev, * next;
+	int result;
+
+	spin_lock(&acpi_device_lock);
+	list_for_each_entry_safe_reverse(dev, next, &acpi_device_list, g_list) {
+		if (dev->driver && dev->driver->ops.suspend) {
+			spin_unlock(&acpi_device_lock);
+			result = dev->driver->ops.suspend(dev, 0);
+			if (result) {
+				printk(KERN_ERR PREFIX "[%s - %s] Suspend failed: %d\n",
+				       acpi_device_name(dev),
+				       acpi_device_bid(dev), result);
+			}
+			spin_lock(&acpi_device_lock);
+		}
+	}
+	spin_unlock(&acpi_device_lock);
 	return 0;
 }
 
-/* --------------------------------------------------------------------------
-                                 Driver Management
-   -------------------------------------------------------------------------- */
+static int acpi_device_suspend(struct device * dev, pm_message_t state)
+{
+	struct acpi_device * acpi_dev = to_acpi_dev(dev);
 
-static LIST_HEAD(acpi_bus_drivers);
+	/*
+	 * For now, we should only register 1 generic device -
+	 * the ACPI root device - and from there, we walk the
+	 * tree of ACPI devices to suspend each one using the
+	 * ACPI driver methods.
+	 */
+	if (acpi_dev->handle == ACPI_ROOT_OBJECT)
+		root_suspend(acpi_dev, state);
+	return 0;
+}
+
+static int root_resume(struct acpi_device * acpi_dev)
+{
+	struct acpi_device * dev, * next;
+	int result;
+
+	spin_lock(&acpi_device_lock);
+	list_for_each_entry_safe(dev, next, &acpi_device_list, g_list) {
+		if (dev->driver && dev->driver->ops.resume) {
+			spin_unlock(&acpi_device_lock);
+			result = dev->driver->ops.resume(dev, 0);
+			if (result) {
+				printk(KERN_ERR PREFIX "[%s - %s] resume failed: %d\n",
+				       acpi_device_name(dev),
+				       acpi_device_bid(dev), result);
+			}
+			spin_lock(&acpi_device_lock);
+		}
+	}
+	spin_unlock(&acpi_device_lock);
+	return 0;
+}
+
+static int acpi_device_resume(struct device * dev)
+{
+	struct acpi_device * acpi_dev = to_acpi_dev(dev);
+
+	/*
+	 * For now, we should only register 1 generic device -
+	 * the ACPI root device - and from there, we walk the
+	 * tree of ACPI devices to resume each one using the
+	 * ACPI driver methods.
+	 */
+	if (acpi_dev->handle == ACPI_ROOT_OBJECT)
+		root_resume(acpi_dev);
+	return 0;
+}
 
 /**
  * acpi_bus_match - match device IDs to driver's supported IDs
@@ -478,6 +317,72 @@ acpi_bus_match(struct acpi_device *devic
 	return acpi_match_ids(device, driver->ids);
 }
 
+static struct bus_type acpi_bus_type = {
+	.name		= "acpi",
+	.suspend	= acpi_device_suspend,
+	.resume		= acpi_device_resume,
+};
+
+static void acpi_device_register(struct acpi_device *device,
+				 struct acpi_device *parent)
+{
+	int err;
+
+	/*
+	 * Linkage
+	 * -------
+	 * Link this device to its parent and siblings.
+	 */
+	INIT_LIST_HEAD(&device->children);
+	INIT_LIST_HEAD(&device->node);
+	INIT_LIST_HEAD(&device->g_list);
+	INIT_LIST_HEAD(&device->wakeup_list);
+
+	spin_lock(&acpi_device_lock);
+	if (device->parent) {
+		list_add_tail(&device->node, &device->parent->children);
+		list_add_tail(&device->g_list, &device->parent->g_list);
+	} else
+		list_add_tail(&device->g_list, &acpi_device_list);
+	if (device->wakeup.flags.valid)
+		list_add_tail(&device->wakeup_list, &acpi_wakeup_device_list);
+	spin_unlock(&acpi_device_lock);
+
+	strlcpy(device->kobj.name, device->pnp.bus_id, KOBJ_NAME_LEN);
+	if (parent)
+		device->kobj.parent = &parent->kobj;
+	device->kobj.ktype = &ktype_acpi_ns;
+	device->kobj.kset = &acpi_namespace_kset;
+	err = kobject_register(&device->kobj);
+	if (err < 0)
+		printk(KERN_WARNING "%s: kobject_register error: %d\n",
+			__FUNCTION__, err);
+	create_sysfs_device_files(device);
+}
+
+static void acpi_device_unregister(struct acpi_device *device, int type)
+{
+	spin_lock(&acpi_device_lock);
+	if (device->parent) {
+		list_del(&device->node);
+		list_del(&device->g_list);
+	} else
+		list_del(&device->g_list);
+
+	list_del(&device->wakeup_list);
+
+	spin_unlock(&acpi_device_lock);
+
+	acpi_detach_data(device->handle, acpi_bus_data_handler);
+	remove_sysfs_device_files(device);
+	kobject_unregister(&device->kobj);
+}
+
+/* --------------------------------------------------------------------------
+                                 Driver Management
+   -------------------------------------------------------------------------- */
+static LIST_HEAD(acpi_bus_drivers);
+
 /**
  * acpi_bus_driver_init - add a device to a driver
  * @device: the device to add and initialize
@@ -668,7 +573,6 @@ static int acpi_bus_find_driver(struct a
 /* --------------------------------------------------------------------------
                                  Device Enumeration
    -------------------------------------------------------------------------- */
-
 acpi_status
 acpi_bus_get_ejd(acpi_handle handle, acpi_handle *ejd)
 {
@@ -691,6 +595,183 @@ acpi_bus_get_ejd(acpi_handle handle, acp
 }
 EXPORT_SYMBOL_GPL(acpi_bus_get_ejd);
 
+void acpi_bus_data_handler(acpi_handle handle, u32 function, void *context)
+{
+
+	/* TBD */
+
+	return;
+}
+
+int acpi_match_ids(struct acpi_device *device, char *ids)
+{
+	if (device->flags.hardware_id)
+		if (strstr(ids, device->pnp.hardware_id))
+			return 0;
+
+	if (device->flags.compatible_ids) {
+		struct acpi_compatible_id_list *cid_list = device->pnp.cid_list;
+		int i;
+
+		/* compare multiple _CID entries against driver ids */
+		for (i = 0; i < cid_list->count; i++) {
+			if (strstr(ids, cid_list->id[i].value))
+				return 0;
+		}
+	}
+	return -ENOENT;
+}
+
+static int acpi_bus_get_perf_flags(struct acpi_device *device)
+{
+	device->performance.state = ACPI_STATE_UNKNOWN;
+	return 0;
+}
+
+static acpi_status
+acpi_bus_extract_wakeup_device_power_package(struct acpi_device *device,
+					     union acpi_object *package)
+{
+	int i = 0;
+	union acpi_object *element = NULL;
+
+	if (!device || !package || (package->package.count < 2))
+		return AE_BAD_PARAMETER;
+
+	element = &(package->package.elements[0]);
+	if (!element)
+		return AE_BAD_PARAMETER;
+	if (element->type == ACPI_TYPE_PACKAGE) {
+		if ((element->package.count < 2) ||
+		    (element->package.elements[0].type !=
+		     ACPI_TYPE_LOCAL_REFERENCE)
+		    || (element->package.elements[1].type != ACPI_TYPE_INTEGER))
+			return AE_BAD_DATA;
+		device->wakeup.gpe_device =
+		    element->package.elements[0].reference.handle;
+		device->wakeup.gpe_number =
+		    (u32) element->package.elements[1].integer.value;
+	} else if (element->type == ACPI_TYPE_INTEGER) {
+		device->wakeup.gpe_number = element->integer.value;
+	} else
+		return AE_BAD_DATA;
+
+	element = &(package->package.elements[1]);
+	if (element->type != ACPI_TYPE_INTEGER) {
+		return AE_BAD_DATA;
+	}
+	device->wakeup.sleep_state = element->integer.value;
+
+	if ((package->package.count - 2) > ACPI_MAX_HANDLES) {
+		return AE_NO_MEMORY;
+	}
+	device->wakeup.resources.count = package->package.count - 2;
+	for (i = 0; i < device->wakeup.resources.count; i++) {
+		element = &(package->package.elements[i + 2]);
+		if (element->type != ACPI_TYPE_ANY) {
+			return AE_BAD_DATA;
+		}
+
+		device->wakeup.resources.handles[i] = element->reference.handle;
+	}
+
+	return AE_OK;
+}
+
+static int acpi_bus_get_wakeup_device_flags(struct acpi_device *device)
+{
+	acpi_status status = 0;
+	struct acpi_buffer buffer = { ACPI_ALLOCATE_BUFFER, NULL };
+	union acpi_object *package = NULL;
+
+
+	/* _PRW */
+	status = acpi_evaluate_object(device->handle, "_PRW", NULL, &buffer);
+	if (ACPI_FAILURE(status)) {
+		ACPI_EXCEPTION((AE_INFO, status, "Evaluating _PRW"));
+		goto end;
+	}
+
+	package = (union acpi_object *)buffer.pointer;
+	status = acpi_bus_extract_wakeup_device_power_package(device, package);
+	if (ACPI_FAILURE(status)) {
+		ACPI_EXCEPTION((AE_INFO, status, "Extracting _PRW package"));
+		goto end;
+	}
+
+	kfree(buffer.pointer);
+
+	device->wakeup.flags.valid = 1;
+	/* Power button, Lid switch always enable wakeup */
+	if (!acpi_match_ids(device, "PNP0C0D,PNP0C0C,PNP0C0E"))
+		device->wakeup.flags.run_wake = 1;
+
+      end:
+	if (ACPI_FAILURE(status))
+		device->flags.wake_capable = 0;
+	return 0;
+}
+
+static int acpi_bus_get_power_flags(struct acpi_device *device)
+{
+	acpi_status status = 0;
+	acpi_handle handle = NULL;
+	u32 i = 0;
+
+
+	/*
+	 * Power Management Flags
+	 */
+	status = acpi_get_handle(device->handle, "_PSC", &handle);
+	if (ACPI_SUCCESS(status))
+		device->power.flags.explicit_get = 1;
+	status = acpi_get_handle(device->handle, "_IRC", &handle);
+	if (ACPI_SUCCESS(status))
+		device->power.flags.inrush_current = 1;
+
+	/*
+	 * Enumerate supported power management states
+	 */
+	for (i = ACPI_STATE_D0; i <= ACPI_STATE_D3; i++) {
+		struct acpi_device_power_state *ps = &device->power.states[i];
+		char object_name[5] = { '_', 'P', 'R', '0' + i, '\0' };
+
+		/* Evaluate "_PRx" to se if power resources are referenced */
+		acpi_evaluate_reference(device->handle, object_name, NULL,
+					&ps->resources);
+		if (ps->resources.count) {
+			device->power.flags.power_resources = 1;
+			ps->flags.valid = 1;
+		}
+
+		/* Evaluate "_PSx" to see if we can do explicit sets */
+		object_name[2] = 'S';
+		status = acpi_get_handle(device->handle, object_name, &handle);
+		if (ACPI_SUCCESS(status)) {
+			ps->flags.explicit_set = 1;
+			ps->flags.valid = 1;
+		}
+
+		/* State is valid if we have some power control */
+		if (ps->resources.count || ps->flags.explicit_set)
+			ps->flags.valid = 1;
+
+		ps->power = -1;	/* Unknown - driver assigned */
+		ps->latency = -1;	/* Unknown - driver assigned */
+	}
+
+	/* Set defaults for D0 and D3 states (always valid) */
+	device->power.states[ACPI_STATE_D0].flags.valid = 1;
+	device->power.states[ACPI_STATE_D0].power = 100;
+	device->power.states[ACPI_STATE_D3].flags.valid = 1;
+	device->power.states[ACPI_STATE_D3].power = 0;
+
+	/* TBD: System wake support and resource requirements. */
+
+	device->power.state = ACPI_STATE_UNKNOWN;
+
+	return 0;
+}
 
 static int acpi_bus_get_flags(struct acpi_device *device)
 {
@@ -1353,100 +1434,6 @@ static int acpi_bus_scan_fixed(struct ac
 	return result;
 }
 
-
-static inline struct acpi_device * to_acpi_dev(struct device * dev)
-{
-	return container_of(dev, struct acpi_device, dev);
-}
-
-
-static int root_suspend(struct acpi_device * acpi_dev, pm_message_t state)
-{
-	struct acpi_device * dev, * next;
-	int result;
-
-	spin_lock(&acpi_device_lock);
-	list_for_each_entry_safe_reverse(dev, next, &acpi_device_list, g_list) {
-		if (dev->driver && dev->driver->ops.suspend) {
-			spin_unlock(&acpi_device_lock);
-			result = dev->driver->ops.suspend(dev, 0);
-			if (result) {
-				printk(KERN_ERR PREFIX "[%s - %s] Suspend failed: %d\n",
-				       acpi_device_name(dev),
-				       acpi_device_bid(dev), result);
-			}
-			spin_lock(&acpi_device_lock);
-		}
-	}
-	spin_unlock(&acpi_device_lock);
-	return 0;
-}
-
-
-static int acpi_device_suspend(struct device * dev, pm_message_t state)
-{
-	struct acpi_device * acpi_dev = to_acpi_dev(dev);
-
-	/*
-	 * For now, we should only register 1 generic device -
-	 * the ACPI root device - and from there, we walk the
-	 * tree of ACPI devices to suspend each one using the
-	 * ACPI driver methods.
-	 */
-	if (acpi_dev->handle == ACPI_ROOT_OBJECT)
-		root_suspend(acpi_dev, state);
-	return 0;
-}
-
-
-
-static int root_resume(struct acpi_device * acpi_dev)
-{
-	struct acpi_device * dev, * next;
-	int result;
-
-	spin_lock(&acpi_device_lock);
-	list_for_each_entry_safe(dev, next, &acpi_device_list, g_list) {
-		if (dev->driver && dev->driver->ops.resume) {
-			spin_unlock(&acpi_device_lock);
-			result = dev->driver->ops.resume(dev, 0);
-			if (result) {
-				printk(KERN_ERR PREFIX "[%s - %s] resume failed: %d\n",
-				       acpi_device_name(dev),
-				       acpi_device_bid(dev), result);
-			}
-			spin_lock(&acpi_device_lock);
-		}
-	}
-	spin_unlock(&acpi_device_lock);
-	return 0;
-}
-
-
-static int acpi_device_resume(struct device * dev)
-{
-	struct acpi_device * acpi_dev = to_acpi_dev(dev);
-
-	/*
-	 * For now, we should only register 1 generic device -
-	 * the ACPI root device - and from there, we walk the
-	 * tree of ACPI devices to resume each one using the
-	 * ACPI driver methods.
-	 */
-	if (acpi_dev->handle == ACPI_ROOT_OBJECT)
-		root_resume(acpi_dev);
-	return 0;
-}
-
-
-static struct bus_type acpi_bus_type = {
-	.name		= "acpi",
-	.suspend	= acpi_device_suspend,
-	.resume		= acpi_device_resume,
-};
-
-
-
 static int __init acpi_scan_init(void)
 {
 	int result;
Signature · 1 line
1.4.4.g59427
author
#2 lore raw

PATCH 2/13 ACPI: rename some functions

From: Zhang Rui <[email protected]>

We want the name 'to_acpi_device'.
And the current macro 'to_acpi_device' will be removed after device model is setup.
So just simply rename them.

---
 drivers/acpi/scan.c |   14 +++++++-------
 1 files changed, 7 insertions(+), 7 deletions(-)
drivers/acpi/scan.c +7 -7
index e0255cb..1f75ba6 100644
@@ -49,13 +49,13 @@ static void setup_sys_fs_device_files(st
 #define remove_sysfs_device_files(dev)	\
 	setup_sys_fs_device_files(dev, (acpi_device_sysfs_files *)&sysfs_remove_file)
 
-#define to_acpi_device(n) container_of(n, struct acpi_device, kobj)
+#define to_acpi_dev(n) container_of(n, struct acpi_device, kobj)
 #define to_handle_attr(n) container_of(n, struct acpi_device_attribute, attr);
 
 static ssize_t acpi_device_attr_show(struct kobject *kobj,
 				     struct attribute *attr, char *buf)
 {
-	struct acpi_device *device = to_acpi_device(kobj);
+	struct acpi_device *device = to_acpi_dev(kobj);
 	struct acpi_device_attribute *attribute = to_handle_attr(attr);
 	return attribute->show ? attribute->show(device, buf) : -EIO;
 }
@@ -63,7 +63,7 @@ static ssize_t acpi_device_attr_store(st
 				      struct attribute *attr, const char *buf,
 				      size_t len)
 {
-	struct acpi_device *device = to_acpi_device(kobj);
+	struct acpi_device *device = to_acpi_dev(kobj);
 	struct acpi_device_attribute *attribute = to_handle_attr(attr);
 	return attribute->store ? attribute->store(device, buf, len) : -EIO;
 }
@@ -82,7 +82,7 @@ static int namespace_uevent(struct kset
 			     char **envp, int num_envp, char *buffer,
 			     int buffer_size)
 {
-	struct acpi_device *dev = to_acpi_device(kobj);
+	struct acpi_device *dev = to_acpi_dev(kobj);
 	int i = 0;
 	int len = 0;
 
@@ -222,7 +222,7 @@ acpi_eject_store(struct acpi_device *dev
 /* --------------------------------------------------------------------------
 			ACPI Bus operations
    -------------------------------------------------------------------------- */
-static inline struct acpi_device * to_acpi_dev(struct device * dev)
+static inline struct acpi_device * to_acpi_device(struct device * dev)
 {
 	return container_of(dev, struct acpi_device, dev);
 }
@@ -251,7 +251,7 @@ static int root_suspend(struct acpi_devi
 
 static int acpi_device_suspend(struct device * dev, pm_message_t state)
 {
-	struct acpi_device * acpi_dev = to_acpi_dev(dev);
+	struct acpi_device * acpi_dev = to_acpi_device(dev);
 
 	/*
 	 * For now, we should only register 1 generic device -
@@ -288,7 +288,7 @@ static int root_resume(struct acpi_devic
 
 static int acpi_device_resume(struct device * dev)
 {
-	struct acpi_device * acpi_dev = to_acpi_dev(dev);
+	struct acpi_device * acpi_dev = to_acpi_device(dev);
 
 	/*
 	 * For now, we should only register 1 generic device -
Signature · 1 line
1.4.4.g59427
author
#3 lore raw

PATCH 3/13 ACPI: add device_driver and helper functions

From: Patrick Mochel <[email protected]>

Add device_driver into acpi_driver for driver model. Add helper functions 'to_acpi_device' and 'to_acpi_driver' to get structure acpi_device/acpi_driver by device/device_driver.

---
 drivers/acpi/scan.c     |    5 -----
 include/acpi/acpi_bus.h |    3 +++
 2 files changed, 3 insertions(+), 5 deletions(-)
drivers/acpi/scan.c +0 -5
index 1f75ba6..5b42948 100644
@@ -222,11 +222,6 @@ acpi_eject_store(struct acpi_device *dev
 /* --------------------------------------------------------------------------
 			ACPI Bus operations
    -------------------------------------------------------------------------- */
-static inline struct acpi_device * to_acpi_device(struct device * dev)
-{
-	return container_of(dev, struct acpi_device, dev);
-}
-
 static int root_suspend(struct acpi_device * acpi_dev, pm_message_t state)
 {
 	struct acpi_device * dev, * next;
include/acpi/acpi_bus.h +3 -0
index f338e40..5282fe7 100644
@@ -136,6 +136,7 @@ struct acpi_driver {
 	atomic_t references;
 	char *ids;		/* Supported Hardware IDs */
 	struct acpi_device_ops ops;
+	struct device_driver drv;
 };
 
 /*
@@ -301,6 +302,8 @@ struct acpi_device {
 };
 
 #define acpi_driver_data(d)	((d)->driver_data)
+#define to_acpi_device(d)	container_of(d, struct acpi_device, dev)
+#define to_acpi_driver(d)	container_of(d, struct acpi_driver, drv)
 
 /*
  * Events
Signature · 1 line
1.4.4.g59427
author
#4 lore raw

PATCH 4/13 ACPI: add ACPI bus_type for driver model

From: Patrick Mochel <[email protected]>

Add ACPI bus_type for Linux driver model.

1. .shutdown method is added into acpi_driver.ops
needed by bus_type operations.
2. remove useless parameter 'int state' in .resume method.
3. change parameter 'int state'
to 'pm_message_t state' in .suspend method.

Note: The new .uevent method mark ACPI drivers by PNPID instead of by name.
Udev script needs to look for "HWID=" or "COMPTID=" to load ACPI drivers as a result.

---
 drivers/acpi/fan.c      |    8 +-
 drivers/acpi/scan.c     |  158 +++++++++++++++++++++++++++--------------------
 drivers/acpi/thermal.c  |    4 +-
 include/acpi/acpi_bus.h |    9 ++-
 4 files changed, 103 insertions(+), 76 deletions(-)
drivers/acpi/fan.c +4 -4
index 045c894..b249420 100644
@@ -48,8 +48,8 @@ MODULE_LICENSE("GPL");
 
 static int acpi_fan_add(struct acpi_device *device);
 static int acpi_fan_remove(struct acpi_device *device, int type);
-static int acpi_fan_suspend(struct acpi_device *device, int state);
-static int acpi_fan_resume(struct acpi_device *device, int state);
+static int acpi_fan_suspend(struct acpi_device *device, pm_message_t state);
+static int acpi_fan_resume(struct acpi_device *device);
 
 static struct acpi_driver acpi_fan_driver = {
 	.name = ACPI_FAN_DRIVER_NAME,
@@ -238,7 +238,7 @@ static int acpi_fan_remove(struct acpi_d
 	return 0;
 }
 
-static int acpi_fan_suspend(struct acpi_device *device, int state)
+static int acpi_fan_suspend(struct acpi_device *device, pm_message_t state)
 {
 	if (!device)
 		return -EINVAL;
@@ -248,7 +248,7 @@ static int acpi_fan_suspend(struct acpi_
 	return AE_OK;
 }
 
-static int acpi_fan_resume(struct acpi_device *device, int state)
+static int acpi_fan_resume(struct acpi_device *device)
 {
 	int result = 0;
 	int power_state = 0;
drivers/acpi/scan.c +91 -67

205 lines not on this page · raw message

drivers/acpi/thermal.c +2 -2
index 5753d06..3650654 100644
@@ -82,7 +82,7 @@ MODULE_PARM_DESC(tzp, "Thermal zone poll
 
 static int acpi_thermal_add(struct acpi_device *device);
 static int acpi_thermal_remove(struct acpi_device *device, int type);
-static int acpi_thermal_resume(struct acpi_device *device, int state);
+static int acpi_thermal_resume(struct acpi_device *device);
 static int acpi_thermal_state_open_fs(struct inode *inode, struct file *file);
 static int acpi_thermal_temp_open_fs(struct inode *inode, struct file *file);
 static int acpi_thermal_trip_open_fs(struct inode *inode, struct file *file);
@@ -1356,7 +1356,7 @@ static int acpi_thermal_remove(struct ac
 	return 0;
 }
 
-static int acpi_thermal_resume(struct acpi_device *device, int state)
+static int acpi_thermal_resume(struct acpi_device *device)
 {
 	struct acpi_thermal *tz = NULL;
 	int i;
include/acpi/acpi_bus.h +6 -3
index 5282fe7..8fb7158 100644
@@ -92,13 +92,14 @@ typedef int (*acpi_op_remove) (struct ac
 typedef int (*acpi_op_lock) (struct acpi_device * device, int type);
 typedef int (*acpi_op_start) (struct acpi_device * device);
 typedef int (*acpi_op_stop) (struct acpi_device * device, int type);
-typedef int (*acpi_op_suspend) (struct acpi_device * device, int state);
-typedef int (*acpi_op_resume) (struct acpi_device * device, int state);
+typedef int (*acpi_op_suspend) (struct acpi_device * device, pm_message_t state);
+typedef int (*acpi_op_resume) (struct acpi_device * device);
 typedef int (*acpi_op_scan) (struct acpi_device * device);
 typedef int (*acpi_op_bind) (struct acpi_device * device);
 typedef int (*acpi_op_unbind) (struct acpi_device * device);
 typedef int (*acpi_op_match) (struct acpi_device * device,
 			      struct acpi_driver * driver);
+typedef int (*acpi_op_shutdown) (struct acpi_device * device);
 
 struct acpi_bus_ops {
 	u32 acpi_op_add:1;
@@ -112,7 +113,8 @@ struct acpi_bus_ops {
 	u32 acpi_op_bind:1;
 	u32 acpi_op_unbind:1;
 	u32 acpi_op_match:1;
-	u32 reserved:21;
+	u32 acpi_op_shutdown:1;
+	u32 reserved:20;
 };
 
 struct acpi_device_ops {
@@ -127,6 +129,7 @@ struct acpi_device_ops {
 	acpi_op_bind bind;
 	acpi_op_unbind unbind;
 	acpi_op_match match;
+	acpi_op_shutdown shutdown;
 };
 
 struct acpi_driver {
Signature · 1 line
1.4.4.g59427
author
#5 lore raw

PATCH 5/13 ACPI: change registration interface to follow driver model

From: Patrick Mochel <[email protected]>

ACPI device/driver registration Interfaces are modified to follow Linux driver model.

---
 drivers/acpi/scan.c     |  175 ++++++++---------------------------------------
 include/acpi/acpi_bus.h |    3 +-
 2 files changed, 30 insertions(+), 148 deletions(-)
drivers/acpi/scan.c +29 -146
index 4647462..b616e17 100644
@@ -25,7 +25,7 @@ DEFINE_SPINLOCK(acpi_device_lock);
 LIST_HEAD(acpi_wakeup_device_list);
 
 
-static void acpi_device_release(struct kobject *kobj)
+static void acpi_device_release_legacy(struct kobject *kobj)
 {
 	struct acpi_device *dev = container_of(kobj, struct acpi_device, kobj);
 	kfree(dev->pnp.cid_list);
@@ -75,7 +75,7 @@ static struct sysfs_ops acpi_device_sysf
 
 static struct kobj_type ktype_acpi_ns = {
 	.sysfs_ops = &acpi_device_sysfs_ops,
-	.release = acpi_device_release,
+	.release = acpi_device_release_legacy,
 };
 
 static int namespace_uevent(struct kset *kset, struct kobject *kobj,
@@ -222,6 +222,14 @@ acpi_eject_store(struct acpi_device *dev
 /* --------------------------------------------------------------------------
 			ACPI Bus operations
    -------------------------------------------------------------------------- */
+static void acpi_device_release(struct device *dev)
+{
+	struct acpi_device *acpi_dev = to_acpi_device(dev);
+
+	kfree(acpi_dev->pnp.cid_list);
+	kfree(acpi_dev);
+}
+
 static int acpi_device_suspend(struct device *dev, pm_message_t state)
 {
 	struct acpi_device *acpi_dev = to_acpi_device(dev);
@@ -377,6 +385,14 @@ static void acpi_device_register(struct
 		printk(KERN_WARNING "%s: kobject_register error: %d\n",
 			__FUNCTION__, err);
 	create_sysfs_device_files(device);
+
+	if (device->parent)
+		device->dev.parent = &parent->dev;
+	device->dev.bus = &acpi_bus_type;
+	device_initialize(&device->dev);
+	sprintf(device->dev.bus_id, "%s", device->pnp.bus_id);
+	device->dev.release = &acpi_device_release;
+	device_add(&device->dev);
 }
 
 static void acpi_device_unregister(struct acpi_device *device, int type)
@@ -395,20 +411,20 @@ static void acpi_device_unregister(struc
 	acpi_detach_data(device->handle, acpi_bus_data_handler);
 	remove_sysfs_device_files(device);
 	kobject_unregister(&device->kobj);
+
+	device_unregister(&device->dev);
 }
 
 /* --------------------------------------------------------------------------
                                  Driver Management
    -------------------------------------------------------------------------- */
-static LIST_HEAD(acpi_bus_drivers);
-
 /**
  * acpi_bus_driver_init - add a device to a driver
  * @device: the device to add and initialize
  * @driver: driver for the device
  *
  * Used to initialize a device via its device driver.  Called whenever a 
- * driver is bound to a device.  Invokes the driver's add() and start() ops.
+ * driver is bound to a device.  Invokes the driver's add() ops.
  */
 static int
 acpi_bus_driver_init(struct acpi_device *device, struct acpi_driver *driver)
@@ -459,57 +475,6 @@ static int acpi_start_single_object(stru
 	return result;
 }
 
-static void acpi_driver_attach(struct acpi_driver *drv)
-{
-	struct list_head *node, *next;
-
-
-	spin_lock(&acpi_device_lock);
-	list_for_each_safe(node, next, &acpi_device_list) {
-		struct acpi_device *dev =
-		    container_of(node, struct acpi_device, g_list);
-
-		if (dev->driver || !dev->status.present)
-			continue;
-		spin_unlock(&acpi_device_lock);
-
-		if (!acpi_bus_match(&(dev->dev), &(drv->drv))) {
-			if (!acpi_bus_driver_init(dev, drv)) {
-				acpi_start_single_object(dev);
-				atomic_inc(&drv->references);
-				ACPI_DEBUG_PRINT((ACPI_DB_INFO,
-						  "Found driver [%s] for device [%s]\n",
-						  drv->name, dev->pnp.bus_id));
-			}
-		}
-		spin_lock(&acpi_device_lock);
-	}
-	spin_unlock(&acpi_device_lock);
-}
-
-static void acpi_driver_detach(struct acpi_driver *drv)
-{
-	struct list_head *node, *next;
-
-
-	spin_lock(&acpi_device_lock);
-	list_for_each_safe(node, next, &acpi_device_list) {
-		struct acpi_device *dev =
-		    container_of(node, struct acpi_device, g_list);
-
-		if (dev->driver == drv) {
-			spin_unlock(&acpi_device_lock);
-			if (drv->ops.remove)
-				drv->ops.remove(dev, ACPI_BUS_REMOVAL_NORMAL);
-			spin_lock(&acpi_device_lock);
-			dev->driver = NULL;
-			dev->driver_data = NULL;
-			atomic_dec(&drv->references);
-		}
-	}
-	spin_unlock(&acpi_device_lock);
-}
-
 /**
  * acpi_bus_register_driver - register a driver with the ACPI bus
  * @driver: driver being registered
@@ -520,16 +485,16 @@ static void acpi_driver_detach(struct ac
  */
 int acpi_bus_register_driver(struct acpi_driver *driver)
 {
+	int ret;
 
 	if (acpi_disabled)
 		return -ENODEV;
+	driver->drv.name = driver->name;
+	driver->drv.bus = &acpi_bus_type;
+	driver->drv.owner = driver->owner;
 
-	spin_lock(&acpi_device_lock);
-	list_add_tail(&driver->node, &acpi_bus_drivers);
-	spin_unlock(&acpi_device_lock);
-	acpi_driver_attach(driver);
-
-	return 0;
+	ret = driver_register(&driver->drv);
+	return ret;
 }
 
 EXPORT_SYMBOL(acpi_bus_register_driver);
@@ -543,52 +508,11 @@ EXPORT_SYMBOL(acpi_bus_register_driver);
  */
 void acpi_bus_unregister_driver(struct acpi_driver *driver)
 {
-	acpi_driver_detach(driver);
-
-	if (!atomic_read(&driver->references)) {
-		spin_lock(&acpi_device_lock);
-		list_del_init(&driver->node);
-		spin_unlock(&acpi_device_lock);
-	}
-	return;
+	driver_unregister(&driver->drv);
 }
 
 EXPORT_SYMBOL(acpi_bus_unregister_driver);
 
-/**
- * acpi_bus_find_driver - check if there is a driver installed for the device
- * @device: device that we are trying to find a supporting driver for
- *
- * Parses the list of registered drivers looking for a driver applicable for
- * the specified device.
- */
-static int acpi_bus_find_driver(struct acpi_device *device)
-{
-	int result = 0;
-	struct list_head *node, *next;
-
-
-	spin_lock(&acpi_device_lock);
-	list_for_each_safe(node, next, &acpi_bus_drivers) {
-		struct acpi_driver *driver =
-		    container_of(node, struct acpi_driver, node);
-
-		atomic_inc(&driver->references);
-		spin_unlock(&acpi_device_lock);
-		if (!acpi_bus_match(&(device->dev), &(driver->drv))) {
-			result = acpi_bus_driver_init(device, driver);
-			if (!result)
-				goto Done;
-		}
-		atomic_dec(&driver->references);
-		spin_lock(&acpi_device_lock);
-	}
-	spin_unlock(&acpi_device_lock);
-
-      Done:
-	return result;
-}
-
 /* --------------------------------------------------------------------------
                                  Device Enumeration
    -------------------------------------------------------------------------- */
@@ -1033,32 +957,10 @@ static void acpi_device_get_debug_info(s
 
 static int acpi_bus_remove(struct acpi_device *dev, int rmdevice)
 {
-	int result = 0;
-	struct acpi_driver *driver;
-
-
 	if (!dev)
 		return -EINVAL;
 
-	driver = dev->driver;
-
-	if ((driver) && (driver->ops.remove)) {
-
-		if (driver->ops.stop) {
-			result = driver->ops.stop(dev, ACPI_BUS_REMOVAL_EJECT);
-			if (result)
-				return result;
-		}
-
-		result = dev->driver->ops.remove(dev, ACPI_BUS_REMOVAL_EJECT);
-		if (result) {
-			return result;
-		}
-
-		atomic_dec(&dev->driver->references);
-		dev->driver = NULL;
-		acpi_driver_data(dev) = NULL;
-	}
+	device_release_driver(&dev->dev);
 
 	if (!rmdevice)
 		return 0;
@@ -1193,17 +1095,6 @@ acpi_add_single_object(struct acpi_devic
 			device->parent->ops.bind(device);
 	}
 
-	/*
-	 * Locate & Attach Driver
-	 * ----------------------
-	 * If there's a hardware id (_HID) or compatible ids (_CID) we check
-	 * to see if there's a driver installed for this kind of device.  Note
-	 * that drivers can install before or after a device is enumerated.
-	 *
-	 * TBD: Assumes LDM provides driver hot-plug capability.
-	 */
-	acpi_bus_find_driver(device);
-
       end:
 	if (!result)
 		*child = device;
@@ -1484,14 +1375,6 @@ static int __init acpi_scan_init(void)
 	if (result)
 		goto Done;
 
-	acpi_root->dev.bus = &acpi_bus_type;
-	snprintf(acpi_root->dev.bus_id, BUS_ID_SIZE, "%s", acpi_bus_type.name);
-	result = device_register(&acpi_root->dev);
-	if (result) {
-		/* We don't want to quit even if we failed to add suspend/resume */
-		printk(KERN_ERR PREFIX "Could not register device\n");
-	}
-
 	/*
 	 * Enumerate devices in the ACPI namespace.
 	 */
include/acpi/acpi_bus.h +1 -2
index 8fb7158..137fdee 100644
@@ -133,13 +133,12 @@ struct acpi_device_ops {
 };
 
 struct acpi_driver {
-	struct list_head node;
 	char name[80];
 	char class[80];
-	atomic_t references;
 	char *ids;		/* Supported Hardware IDs */
 	struct acpi_device_ops ops;
 	struct device_driver drv;
+	struct module *owner;
 };
 
 /*
Signature · 1 line
1.4.4.g59427
author
#6 lore raw

PATCH 6/13 ACPI: adjust init order

From: Li Shaohua <[email protected]>

Adjust link order to add ACPI devices to global list before PCI devices. In addition, acpi_bus type must be initialized before any driver loads.

---
 drivers/acpi/Makefile |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)
drivers/acpi/Makefile +1 -1
index bce7ca2..a749510 100644
@@ -37,6 +37,7 @@ endif
 
 obj-y				+= sleep/
 obj-y				+= bus.o glue.o
+obj-y				+= scan.o motherboard.o
 obj-$(CONFIG_ACPI_AC) 		+= ac.o
 obj-$(CONFIG_ACPI_BATTERY)	+= battery.o
 obj-$(CONFIG_ACPI_BUTTON)	+= button.o
@@ -56,7 +57,6 @@ obj-$(CONFIG_ACPI_NUMA)		+= numa.o
 obj-$(CONFIG_ACPI_ASUS)		+= asus_acpi.o
 obj-$(CONFIG_ACPI_IBM)		+= ibm_acpi.o
 obj-$(CONFIG_ACPI_TOSHIBA)	+= toshiba_acpi.o
-obj-y				+= scan.o motherboard.o
 obj-$(CONFIG_ACPI_HOTPLUG_MEMORY)	+= acpi_memhotplug.o
 obj-y				+= cm_sbs.o
 obj-$(CONFIG_ACPI_SBS)		+= i2c_ec.o sbs.o
Signature · 1 line
1.4.4.g59427
author
#7 lore raw

PATCH 7/13 ACPI: convert to sysfs framework

From: Patrick Mochel <[email protected]>

Setup new sysfs framework

1. Remove /sys/firmware/acpi
2. Add ACPI device in device tree.

File "eject" for every device that has _EJ0 method is moved from /sys/firmware to /sys/devices.
Operation on this file is exactly the same as before. i.e. echo 1 to "eject" will cause hot removal of this device. Corresponding changes should be made in userspace for hot removal.

---
 drivers/acpi/bus.c            |    2 +-
 drivers/acpi/container.c      |    6 +-
 drivers/acpi/processor_core.c |    8 +-
 drivers/acpi/scan.c           |  187 +++++++++--------------------------------
 include/acpi/acpi_bus.h       |    1 -
 5 files changed, 49 insertions(+), 155 deletions(-)
drivers/acpi/bus.c +1 -1
index 279c4ba..da471f6 100644
@@ -195,7 +195,7 @@ int acpi_bus_set_power(acpi_handle handl
 
 	if (!device->flags.power_manageable) {
 		ACPI_DEBUG_PRINT((ACPI_DB_INFO, "Device `[%s]' is not power manageable\n",
-				device->kobj.name));
+				device->dev.kobj.name));
 		return -ENODEV;
 	}
 	/*
drivers/acpi/container.c +3 -3
index 871aa52..914f56a 100644
@@ -168,7 +168,7 @@ static void container_notify_cb(acpi_han
 			if (ACPI_FAILURE(status) || !device) {
 				result = container_device_add(&device, handle);
 				if (!result)
-					kobject_uevent(&device->kobj,
+					kobject_uevent(&device->dev.kobj,
 						       KOBJ_ONLINE);
 				else
 					printk("Failed to add container\n");
@@ -176,13 +176,13 @@ static void container_notify_cb(acpi_han
 		} else {
 			if (ACPI_SUCCESS(status)) {
 				/* device exist and this is a remove request */
-				kobject_uevent(&device->kobj, KOBJ_OFFLINE);
+				kobject_uevent(&device->dev.kobj, KOBJ_OFFLINE);
 			}
 		}
 		break;
 	case ACPI_NOTIFY_EJECT_REQUEST:
 		if (!acpi_bus_get_device(handle, &device) && device) {
-			kobject_uevent(&device->kobj, KOBJ_OFFLINE);
+			kobject_uevent(&device->dev.kobj, KOBJ_OFFLINE);
 		}
 		break;
 	default:
drivers/acpi/processor_core.c +4 -4
index 1908e0d..46e72c3 100644
@@ -711,7 +711,7 @@ int acpi_processor_device_add(acpi_handl
 		return -ENODEV;
 
 	if ((pr->id >= 0) && (pr->id < NR_CPUS)) {
-		kobject_uevent(&(*device)->kobj, KOBJ_ONLINE);
+		kobject_uevent(&(*device)->dev.kobj, KOBJ_ONLINE);
 	}
 	return 0;
 }
@@ -749,13 +749,13 @@ acpi_processor_hotplug_notify(acpi_handl
 		}
 
 		if (pr->id >= 0 && (pr->id < NR_CPUS)) {
-			kobject_uevent(&device->kobj, KOBJ_OFFLINE);
+			kobject_uevent(&device->dev.kobj, KOBJ_OFFLINE);
 			break;
 		}
 
 		result = acpi_processor_start(device);
 		if ((!result) && ((pr->id >= 0) && (pr->id < NR_CPUS))) {
-			kobject_uevent(&device->kobj, KOBJ_ONLINE);
+			kobject_uevent(&device->dev.kobj, KOBJ_ONLINE);
 		} else {
 			printk(KERN_ERR PREFIX "Device [%s] failed to start\n",
 				    acpi_device_bid(device));
@@ -778,7 +778,7 @@ acpi_processor_hotplug_notify(acpi_handl
 		}
 
 		if ((pr->id < NR_CPUS) && (cpu_present(pr->id)))
-			kobject_uevent(&device->kobj, KOBJ_OFFLINE);
+			kobject_uevent(&device->dev.kobj, KOBJ_OFFLINE);
 		break;
 	default:
 		ACPI_DEBUG_PRINT((ACPI_DB_INFO,
drivers/acpi/scan.c +41 -146

256 lines not on this page · raw message

include/acpi/acpi_bus.h +0 -1
index 137fdee..d409d9a 100644
@@ -299,7 +299,6 @@ struct acpi_device {
 	struct acpi_device_ops ops;
 	struct acpi_driver *driver;
 	void *driver_data;
-	struct kobject kobj;
 	struct device dev;
 };
 
Signature · 1 line
1.4.4.g59427
author
#8 lore raw

PATCH 8/13 ACPI: add acpi_bus_ops in acpi_device

From: Li Shaohua <[email protected]>

Add acpi_bus_ops in acpi_device to support acpi hot plug.

NOTE: Two methods .add and .start in acpi_driver.ops are
called separately to probe ACPI devices, while only .probe method is called in driver model. As executing .add and .start separately is critical for ACPI device hot plug, we use acpi_bus_ops to distinguish different code path.

---
 drivers/acpi/scan.c     |   55 ++++++++++++++++++++++++-----------------------
 include/acpi/acpi_bus.h |    1 +
 2 files changed, 29 insertions(+), 27 deletions(-)
drivers/acpi/scan.c +28 -27
index 97f6bbd..2a82645 100644
@@ -212,7 +212,8 @@ static int acpi_device_probe(struct devi
 
 	ret = acpi_bus_driver_init(acpi_dev, acpi_drv);
 	if (!ret) {
-		acpi_start_single_object(acpi_dev);
+		if (acpi_dev->bus_ops.acpi_op_start)
+			acpi_start_single_object(acpi_dev);
 		ACPI_DEBUG_PRINT((ACPI_DB_INFO,
 			"Found driver [%s] for device [%s]\n",
 			acpi_drv->name, acpi_dev->pnp.bus_id));
@@ -305,7 +306,6 @@ static void acpi_device_unregister(struc
 		list_del(&device->g_list);
 
 	list_del(&device->wakeup_list);
-
 	spin_unlock(&acpi_device_lock);
 
 	acpi_detach_data(device->handle, acpi_bus_data_handler);
@@ -876,7 +876,8 @@ static int acpi_bus_remove(struct acpi_d
 
 static int
 acpi_add_single_object(struct acpi_device **child,
-		       struct acpi_device *parent, acpi_handle handle, int type)
+		       struct acpi_device *parent, acpi_handle handle, int type,
+			struct acpi_bus_ops *ops)
 {
 	int result = 0;
 	struct acpi_device *device = NULL;
@@ -894,6 +895,8 @@ acpi_add_single_object(struct acpi_devic
 
 	device->handle = handle;
 	device->parent = parent;
+	device->bus_ops = *ops; /* workround for not call .start */
+
 
 	acpi_device_get_busid(device, handle, type);
 
@@ -1079,14 +1082,14 @@ static int acpi_bus_scan(struct acpi_dev
 
 		if (ops->acpi_op_add)
 			status = acpi_add_single_object(&child, parent,
-							chandle, type);
+				chandle, type, ops);
 		else
 			status = acpi_bus_get_device(chandle, &child);
 
 		if (ACPI_FAILURE(status))
 			continue;
 
-		if (ops->acpi_op_start) {
+		if (ops->acpi_op_start && !(ops->acpi_op_add)) {
 			status = acpi_start_single_object(child);
 			if (ACPI_FAILURE(status))
 				continue;
@@ -1124,13 +1127,13 @@ acpi_bus_add(struct acpi_device **child,
 	int result;
 	struct acpi_bus_ops ops;
 
+	memset(&ops, 0, sizeof(ops));
+	ops.acpi_op_add = 1;
 
-	result = acpi_add_single_object(child, parent, handle, type);
-	if (!result) {
-		memset(&ops, 0, sizeof(ops));
-		ops.acpi_op_add = 1;
+	result = acpi_add_single_object(child, parent, handle, type, &ops);
+	if (!result)
 		result = acpi_bus_scan(*child, &ops);
-	}
+
 	return result;
 }
 
@@ -1216,28 +1219,30 @@ static int acpi_bus_scan_fixed(struct ac
 {
 	int result = 0;
 	struct acpi_device *device = NULL;
-
+	struct acpi_bus_ops ops;
 
 	if (!root)
 		return -ENODEV;
 
+	memset(&ops, 0, sizeof(ops));
+	ops.acpi_op_add = 1;
+	ops.acpi_op_start = 1;
+
 	/*
 	 * Enumerate all fixed-feature devices.
 	 */
 	if (acpi_fadt.pwr_button == 0) {
 		result = acpi_add_single_object(&device, acpi_root,
 						NULL,
-						ACPI_BUS_TYPE_POWER_BUTTON);
-		if (!result)
-			result = acpi_start_single_object(device);
+						ACPI_BUS_TYPE_POWER_BUTTON,
+						&ops);
 	}
 
 	if (acpi_fadt.sleep_button == 0) {
 		result = acpi_add_single_object(&device, acpi_root,
 						NULL,
-						ACPI_BUS_TYPE_SLEEP_BUTTON);
-		if (!result)
-			result = acpi_start_single_object(device);
+						ACPI_BUS_TYPE_SLEEP_BUTTON,
+						&ops);
 	}
 
 	return result;
@@ -1252,6 +1257,10 @@ static int __init acpi_scan_init(void)
 	if (acpi_disabled)
 		return 0;
 
+	memset(&ops, 0, sizeof(ops));
+	ops.acpi_op_add = 1;
+	ops.acpi_op_start = 1;
+
 	result = bus_register(&acpi_bus_type);
 	if (result) {
 		/* We don't want to quit even if we failed to add suspend/resume */
@@ -1262,11 +1271,7 @@ static int __init acpi_scan_init(void)
 	 * Create the root device in the bus's device tree
 	 */
 	result = acpi_add_single_object(&acpi_root, NULL, ACPI_ROOT_OBJECT,
-					ACPI_BUS_TYPE_SYSTEM);
-	if (result)
-		goto Done;
-
-	result = acpi_start_single_object(acpi_root);
+					ACPI_BUS_TYPE_SYSTEM, &ops);
 	if (result)
 		goto Done;
 
@@ -1274,12 +1279,8 @@ static int __init acpi_scan_init(void)
 	 * Enumerate devices in the ACPI namespace.
 	 */
 	result = acpi_bus_scan_fixed(acpi_root);
-	if (!result) {
-		memset(&ops, 0, sizeof(ops));
-		ops.acpi_op_add = 1;
-		ops.acpi_op_start = 1;
+	if (!result)
 		result = acpi_bus_scan(acpi_root, &ops);
-	}
 
 	if (result)
 		acpi_device_unregister(acpi_root, ACPI_BUS_REMOVAL_NORMAL);
include/acpi/acpi_bus.h +1 -0
index d409d9a..b7baac7 100644
@@ -300,6 +300,7 @@ struct acpi_device {
 	struct acpi_driver *driver;
 	void *driver_data;
 	struct device dev;
+	struct acpi_bus_ops bus_ops;	/* workaround for different code path for hotplug */
 };
 
 #define acpi_driver_data(d)	((d)->driver_data)
Signature · 1 line
1.4.4.g59427
author
#9 lore raw

PATCH 9/13 ACPI: add acpi_bus_removal_type in acpi_device

From: Li Shaohua <[email protected]>

Add removal_type in structure acpi_device for hot removal.

ACPI_BUS_REMOVAL_EJECT is used for ACPI device hot removal. Only one parameter is allowed in .remove method due to driver model. So removal_type is added to indicate different removal type.

---
 drivers/acpi/scan.c     |    6 ++++--
 include/acpi/acpi_bus.h |    1 +
 2 files changed, 5 insertions(+), 2 deletions(-)
drivers/acpi/scan.c +4 -2
index 2a82645..06b86fa 100644
@@ -229,9 +229,9 @@ static int acpi_device_remove(struct dev
 
 	if (acpi_drv) {
 		if (acpi_drv->ops.stop)
-			acpi_drv->ops.stop(acpi_dev, ACPI_BUS_REMOVAL_NORMAL);
+			acpi_drv->ops.stop(acpi_dev, acpi_dev->removal_type);
 		if (acpi_drv->ops.remove)
-			acpi_drv->ops.remove(acpi_dev, ACPI_BUS_REMOVAL_NORMAL);
+			acpi_drv->ops.remove(acpi_dev, acpi_dev->removal_type);
 	}
 	acpi_dev->driver = NULL;
 	acpi_driver_data(dev) = NULL;
@@ -294,6 +294,7 @@ static void acpi_device_register(struct
 	device_add(&device->dev);
 
 	acpi_device_setup_files(device);
+	device->removal_type = ACPI_BUS_REMOVAL_NORMAL;
 }
 
 static void acpi_device_unregister(struct acpi_device *device, int type)
@@ -859,6 +860,7 @@ static int acpi_bus_remove(struct acpi_d
 	if (!dev)
 		return -EINVAL;
 
+	dev->removal_type = ACPI_BUS_REMOVAL_EJECT;
 	device_release_driver(&dev->dev);
 
 	if (!rmdevice)
include/acpi/acpi_bus.h +1 -0
index b7baac7..168ef22 100644
@@ -301,6 +301,7 @@ struct acpi_device {
 	void *driver_data;
 	struct device dev;
 	struct acpi_bus_ops bus_ops;	/* workaround for different code path for hotplug */
+	enum acpi_bus_removal_type removal_type; /* indicate for different removal type */
 };
 
 #define acpi_driver_data(d)	((d)->driver_data)
Signature · 1 line
1.4.4.g59427
author
#10 lore raw

PATCH 10/13 ACPI: consolidate two motherboard drivers into one

From: Li Shaohua <[email protected]>

Consolidate motherboard1 and motherboard2 drivers into one so that driver core doesn't complain that two drivers have the same name.

---
 drivers/acpi/motherboard.c |   19 ++++---------------
 1 files changed, 4 insertions(+), 15 deletions(-)
drivers/acpi/motherboard.c +4 -15
index 2e17ec7..bedb511 100644
@@ -33,8 +33,7 @@
 ACPI_MODULE_NAME("acpi_motherboard")
 
 /* Dell use PNP0C01 instead of PNP0C02 */
-#define ACPI_MB_HID1			"PNP0C01"
-#define ACPI_MB_HID2			"PNP0C02"
+#define ACPI_MB_HID			"PNP0C01,PNP0C02"
 /**
  * Doesn't care about legacy IO ports, only IO ports beyond 0x1000 are reserved
  * Doesn't care about the failure of 'request_region', since other may reserve
@@ -110,19 +109,10 @@ static int acpi_motherboard_add(struct a
 	return 0;
 }
 
-static struct acpi_driver acpi_motherboard_driver1 = {
+static struct acpi_driver acpi_motherboard_driver = {
 	.name = "motherboard",
 	.class = "",
-	.ids = ACPI_MB_HID1,
-	.ops = {
-		.add = acpi_motherboard_add,
-		},
-};
-
-static struct acpi_driver acpi_motherboard_driver2 = {
-	.name = "motherboard",
-	.class = "",
-	.ids = ACPI_MB_HID2,
+	.ids = ACPI_MB_HID,
 	.ops = {
 		.add = acpi_motherboard_add,
 		},
@@ -173,8 +163,7 @@ static void __init acpi_reserve_resource
 
 static int __init acpi_motherboard_init(void)
 {
-	acpi_bus_register_driver(&acpi_motherboard_driver1);
-	acpi_bus_register_driver(&acpi_motherboard_driver2);
+	acpi_bus_register_driver(&acpi_motherboard_driver);
 	/*
 	 * Guarantee motherboard IO reservation first
 	 * This module must run after scan.c
Signature · 1 line
1.4.4.g59427
author
#11 lore raw

PATCH 11/13 ACPI: Convert ACPI PCI .bind/.unbind to use PCI bridge driver

From: Li Shaohua <[email protected]>

acpi_device had a .bind/.unbind methods, but Linux driver model does not. Cut ACPI PCI code over to use the Linux driver model methods.

Convert bind/unbind to use a new pci bridge driver. The driver will add/remove _PRT, so we can eventually remove .bind/.unbind methods.

---
 drivers/acpi/pci_bind.c |   56 +++++++++++++++++++++++++++++++++++++++++++---
 drivers/acpi/pci_root.c |    5 ----
 drivers/acpi/scan.c     |   17 ++-----------
 3 files changed, 55 insertions(+), 23 deletions(-)
drivers/acpi/pci_bind.c +52 -4
index 1e2ae6e..d833274 100644
@@ -223,8 +223,6 @@ int acpi_pci_bind(struct acpi_device *de
 				  data->id.segment, data->id.bus,
 				  data->id.device, data->id.function));
 		data->bus = data->dev->subordinate;
-		device->ops.bind = acpi_pci_bind;
-		device->ops.unbind = acpi_pci_unbind;
 	}
 
 	/*
@@ -354,8 +352,6 @@ acpi_pci_bind_root(struct acpi_device *d
 
 	data->id = *id;
 	data->bus = bus;
-	device->ops.bind = acpi_pci_bind;
-	device->ops.unbind = acpi_pci_unbind;
 
 	acpi_get_name(device->handle, ACPI_FULL_PATHNAME, &buffer);
 
@@ -378,3 +374,55 @@ acpi_pci_bind_root(struct acpi_device *d
 
 	return result;
 }
+
+#define ACPI_PCI_BRIDGE_DRIVER_NAME "ACPI PCI Bridge Driver"
+
+static int acpi_pci_bridge_add(struct acpi_device *device);
+static int acpi_pci_bridge_remove(struct acpi_device *device, int type);
+static int acpi_pci_bridge_match(struct acpi_device *device,
+       struct acpi_driver *driver);
+static struct acpi_driver acpi_pci_bridge_driver = {
+       .name = ACPI_PCI_BRIDGE_DRIVER_NAME,
+       .ops = {
+               .add = acpi_pci_bridge_add,
+               .remove = acpi_pci_bridge_remove,
+               .match = acpi_pci_bridge_match,
+       },
+};
+
+static int acpi_pci_bridge_match(struct acpi_device *device,
+       struct acpi_driver *driver)
+{
+       acpi_status status;
+       acpi_handle handle;
+
+       /* pci bridge has _PRT but isn't PNP0A03 */
+       status = acpi_get_handle(device->handle, METHOD_NAME__PRT, &handle);
+       if (ACPI_FAILURE(status))
+               return -ENODEV;
+       if (!acpi_match_ids(device, "PNP0A03"))
+               return -ENODEV;
+       return 0;
+}
+
+static int acpi_pci_bridge_add(struct acpi_device *device)
+{
+       return acpi_pci_bind(device);
+}
+
+static int acpi_pci_bridge_remove(struct acpi_device *device, int type)
+{
+       return acpi_pci_unbind(device);
+}
+
+static int __init acpi_pci_bridge_init(void)
+{
+       if (acpi_pci_disabled)
+               return 0;
+       if (acpi_bus_register_driver(&acpi_pci_bridge_driver) < 0)
+               return -ENODEV;
+       return 0;
+}
+
+/* Should be called after ACPI pci root driver */
+subsys_initcall(acpi_pci_bridge_init);
drivers/acpi/pci_root.c +0 -5
index 0984a1e..9cfc741 100644
@@ -175,11 +175,6 @@ static int acpi_pci_root_add(struct acpi
 	strcpy(acpi_device_class(device), ACPI_PCI_ROOT_CLASS);
 	acpi_driver_data(device) = root;
 
-	/*
-	 * TBD: Doesn't the bus driver automatically set this?
-	 */
-	device->ops.bind = acpi_pci_bind;
-
 	/* 
 	 * Segment
 	 * -------
drivers/acpi/scan.c +3 -14
index 06b86fa..b5fab54 100644
@@ -865,12 +865,13 @@ static int acpi_bus_remove(struct acpi_d
 
 	if (!rmdevice)
 		return 0;
-
+	/* FIXME: device_release_driver will automically call unbind, is this ok */
+#if 0
 	if (dev->flags.bus_address) {
 		if ((dev->parent) && (dev->parent->ops.unbind))
 			dev->parent->ops.unbind(dev);
 	}
-
+#endif
 	acpi_device_unregister(dev, ACPI_BUS_REMOVAL_EJECT);
 
 	return 0;
@@ -987,18 +988,6 @@ acpi_add_single_object(struct acpi_devic
 
 	acpi_device_register(device, parent);
 
-	/*
-	 * Bind _ADR-Based Devices
-	 * -----------------------
-	 * If there's a a bus address (_ADR) then we utilize the parent's 
-	 * 'bind' function (if exists) to bind the ACPI- and natively-
-	 * enumerated device representations.
-	 */
-	if (device->flags.bus_address) {
-		if (device->parent && device->parent->ops.bind)
-			device->parent->ops.bind(device);
-	}
-
       end:
 	if (!result)
 		*child = device;
Signature · 1 line
1.4.4.g59427
author
#12 lore raw

PATCH 12/13 ACPI: Set fake hid for non-PNPID ACPI devices.

From: Zhang Rui <[email protected]>

We do this mainly because:
1. hid is used to match ACPI devices and drivers.
.match method which is incompatible to driver model can be deleted from acpi_driver.ops then.
2. As the .uevent method mark ACPI drivers by PNPID,
fake hid is set to non-PNPID devices so that udev script can load the right ACPI driver by looking for "HWID = " or "COMPTID = ".

---
 drivers/acpi/pci_bind.c     |   20 +-------------
 drivers/acpi/scan.c         |   59 +++++++++++++++++++++++++++++++++++++++++-
 drivers/acpi/video.c        |   37 +--------------------------
 include/acpi/acpi_bus.h     |    6 +---
 include/acpi/acpi_drivers.h |    2 +
 5 files changed, 63 insertions(+), 61 deletions(-)
drivers/acpi/pci_bind.c +2 -18
index d833274..aa05e92 100644
@@ -379,32 +379,16 @@ acpi_pci_bind_root(struct acpi_device *d
 
 static int acpi_pci_bridge_add(struct acpi_device *device);
 static int acpi_pci_bridge_remove(struct acpi_device *device, int type);
-static int acpi_pci_bridge_match(struct acpi_device *device,
-       struct acpi_driver *driver);
+
 static struct acpi_driver acpi_pci_bridge_driver = {
        .name = ACPI_PCI_BRIDGE_DRIVER_NAME,
+	.ids = ACPI_PCI_BRIDGE_HID,
        .ops = {
                .add = acpi_pci_bridge_add,
                .remove = acpi_pci_bridge_remove,
-               .match = acpi_pci_bridge_match,
        },
 };
 
-static int acpi_pci_bridge_match(struct acpi_device *device,
-       struct acpi_driver *driver)
-{
-       acpi_status status;
-       acpi_handle handle;
-
-       /* pci bridge has _PRT but isn't PNP0A03 */
-       status = acpi_get_handle(device->handle, METHOD_NAME__PRT, &handle);
-       if (ACPI_FAILURE(status))
-               return -ENODEV;
-       if (!acpi_match_ids(device, "PNP0A03"))
-               return -ENODEV;
-       return 0;
-}
-
 static int acpi_pci_bridge_add(struct acpi_device *device)
 {
        return acpi_pci_bind(device);
drivers/acpi/scan.c +57 -2

77 lines not on this page · raw message

drivers/acpi/video.c +1 -36
index 56666a9..6e99eea 100644
@@ -65,16 +65,14 @@ MODULE_LICENSE("GPL");
 
 static int acpi_video_bus_add(struct acpi_device *device);
 static int acpi_video_bus_remove(struct acpi_device *device, int type);
-static int acpi_video_bus_match(struct acpi_device *device,
-				struct acpi_driver *driver);
 
 static struct acpi_driver acpi_video_bus = {
 	.name = ACPI_VIDEO_DRIVER_NAME,
 	.class = ACPI_VIDEO_CLASS,
+	.ids = ACPI_VIDEO_HID,
 	.ops = {
 		.add = acpi_video_bus_add,
 		.remove = acpi_video_bus_remove,
-		.match = acpi_video_bus_match,
 		},
 };
 
@@ -1774,39 +1772,6 @@ static int acpi_video_bus_remove(struct
 	return 0;
 }
 
-static int
-acpi_video_bus_match(struct acpi_device *device, struct acpi_driver *driver)
-{
-	acpi_handle h_dummy1;
-	acpi_handle h_dummy2;
-	acpi_handle h_dummy3;
-
-
-	if (!device || !driver)
-		return -EINVAL;
-
-	/* Since there is no HID, CID for ACPI Video drivers, we have
-	 * to check well known required nodes for each feature we support.
-	 */
-
-	/* Does this device able to support video switching ? */
-	if (ACPI_SUCCESS(acpi_get_handle(device->handle, "_DOD", &h_dummy1)) &&
-	    ACPI_SUCCESS(acpi_get_handle(device->handle, "_DOS", &h_dummy2)))
-		return 0;
-
-	/* Does this device able to retrieve a video ROM ? */
-	if (ACPI_SUCCESS(acpi_get_handle(device->handle, "_ROM", &h_dummy1)))
-		return 0;
-
-	/* Does this device able to configure which video head to be POSTed ? */
-	if (ACPI_SUCCESS(acpi_get_handle(device->handle, "_VPO", &h_dummy1)) &&
-	    ACPI_SUCCESS(acpi_get_handle(device->handle, "_GPD", &h_dummy2)) &&
-	    ACPI_SUCCESS(acpi_get_handle(device->handle, "_SPD", &h_dummy3)))
-		return 0;
-
-	return -ENODEV;
-}
-
 static int __init acpi_video_init(void)
 {
 	int result = 0;
include/acpi/acpi_bus.h +1 -5
index 168ef22..5aea83b 100644
@@ -97,8 +97,6 @@ typedef int (*acpi_op_resume) (struct ac
 typedef int (*acpi_op_scan) (struct acpi_device * device);
 typedef int (*acpi_op_bind) (struct acpi_device * device);
 typedef int (*acpi_op_unbind) (struct acpi_device * device);
-typedef int (*acpi_op_match) (struct acpi_device * device,
-			      struct acpi_driver * driver);
 typedef int (*acpi_op_shutdown) (struct acpi_device * device);
 
 struct acpi_bus_ops {
@@ -112,9 +110,8 @@ struct acpi_bus_ops {
 	u32 acpi_op_scan:1;
 	u32 acpi_op_bind:1;
 	u32 acpi_op_unbind:1;
-	u32 acpi_op_match:1;
 	u32 acpi_op_shutdown:1;
-	u32 reserved:20;
+	u32 reserved:21;
 };
 
 struct acpi_device_ops {
@@ -128,7 +125,6 @@ struct acpi_device_ops {
 	acpi_op_scan scan;
 	acpi_op_bind bind;
 	acpi_op_unbind unbind;
-	acpi_op_match match;
 	acpi_op_shutdown shutdown;
 };
 
include/acpi/acpi_drivers.h +2 -0
index 6a5bdce..be67750 100644
@@ -43,6 +43,8 @@
 #define ACPI_BUTTON_HID_POWERF		"ACPI_FPB"
 #define ACPI_BUTTON_HID_SLEEPF		"ACPI_FSB"
 
+#define ACPI_VIDEO_HID			"ACPI_VID"
+#define ACPI_PCI_BRIDGE_HID		"ACPI_PCI"
 /* --------------------------------------------------------------------------
                                        PCI
    -------------------------------------------------------------------------- */
Signature · 1 line
1.4.4.g59427
author
#13 lore raw

PATCH 13/13 ACPI: use unique number as bus_id of ACPI device in sysfs

From: Zhang Rui <[email protected]>

Previously we used the device name in the DSDT, but would crash upon encountering a duplicate. Also, exposing the DSDT device name to the user in a path isn't a good idea, becauase it is arbitrary.
So just add two attributes for each device,
the full pathname in ACPI namespace and hardware_id.

---
 drivers/acpi/scan.c |   70 +++++++++++++++++++++++++++++++++++++++++++++------
 1 files changed, 62 insertions(+), 8 deletions(-)
drivers/acpi/scan.c +62 -8
index 4a1484c..5e8b8b0 100644
@@ -24,6 +24,8 @@ static LIST_HEAD(acpi_device_list);
 DEFINE_SPINLOCK(acpi_device_lock);
 LIST_HEAD(acpi_wakeup_device_list);
 
+static unsigned int device_id = 0;
+
 static int acpi_eject_operation(acpi_handle handle, int lockable)
 {
 	struct acpi_object_list arg_list;
@@ -103,18 +105,55 @@ acpi_eject_store(struct device *d, struc
 
 static DEVICE_ATTR(eject, 0200, NULL, acpi_eject_store);
 
-static void acpi_device_setup_files(struct acpi_device *dev)
+static ssize_t
+acpi_device_hid_show(struct device *dev, struct device_attribute *attr, char *buf) {
+	struct acpi_device *acpi_dev = to_acpi_device(dev);
+
+	return sprintf(buf, "%s\n", acpi_dev->pnp.hardware_id);
+}
+static DEVICE_ATTR(hid, 0444, acpi_device_hid_show, NULL);
+
+static ssize_t
+acpi_device_path_show(struct device *dev, struct device_attribute *attr, char *buf) {
+	struct acpi_device *acpi_dev = to_acpi_device(dev);
+	struct acpi_buffer path = {ACPI_ALLOCATE_BUFFER, NULL};
+	int result;
+
+	result = acpi_get_name(acpi_dev->handle, ACPI_FULL_PATHNAME, &path);
+	if(result)
+		goto end;
+
+	result = sprintf(buf, "%s\n", (char*)path.pointer);
+	kfree(path.pointer);
+  end:
+	return result;
+}
+static DEVICE_ATTR(path, 0444, acpi_device_path_show, NULL);
+
+static int acpi_device_setup_files(struct acpi_device *dev)
 {
 	acpi_status status;
 	acpi_handle temp;
-
+	int result;
 	/*
 	 * If device has _EJ0, 'eject' file is created that is used to trigger
 	 * hot-removal function from userland.
 	 */
+	result = device_create_file(&dev->dev, &dev_attr_path);
+	if(result)
+		goto end;
+
+	if(dev->flags.hardware_id) {
+		result = device_create_file(&dev->dev, &dev_attr_hid);
+		if(result)
+			goto end;
+	}
+
 	status = acpi_get_handle(dev->handle, "_EJ0", &temp);
 	if (ACPI_SUCCESS(status))
-		device_create_file(&dev->dev, &dev_attr_eject);
+		result = device_create_file(&dev->dev, &dev_attr_eject);
+  end:
+	return result;
 }
 
 static void acpi_device_remove_files(struct acpi_device *dev)
@@ -129,6 +168,11 @@ static void acpi_device_remove_files(str
 	status = acpi_get_handle(dev->handle, "_EJ0", &temp);
 	if (ACPI_SUCCESS(status))
 		device_remove_file(&dev->dev, &dev_attr_eject);
+
+	if(dev->flags.hardware_id)
+		device_remove_file(&dev->dev, &dev_attr_hid);
+
+	device_remove_file(&dev->dev, &dev_attr_path);
 }
 /* --------------------------------------------------------------------------
 			ACPI Bus operations
@@ -260,9 +304,10 @@ static struct bus_type acpi_bus_type = {
 	.uevent		= acpi_device_uevent,
 };
 
-static void acpi_device_register(struct acpi_device *device,
+static int acpi_device_register(struct acpi_device *device,
 				 struct acpi_device *parent)
 {
+	int result;
 	/*
 	 * Linkage
 	 * -------
@@ -287,12 +332,21 @@ static void acpi_device_register(struct
 		device->dev.parent = &parent->dev;
 	device->dev.bus = &acpi_bus_type;
 	device_initialize(&device->dev);
-	sprintf(device->dev.bus_id, "%s", device->pnp.bus_id);
+	sprintf(device->dev.bus_id, "%d", device_id);
 	device->dev.release = &acpi_device_release;
-	device_add(&device->dev);
+	result = device_add(&device->dev);
+	if(result) {
+		printk("Error adding device %s", device->pnp.bus_id);
+		return result;
+	}
+
+	result = acpi_device_setup_files(device);
+	if(result)
+		ACPI_DEBUG_PRINT((ACPI_DB_ERROR, "Error creating sysfs interface for device %s\n", device->pnp.bus_id));
 
-	acpi_device_setup_files(device);
 	device->removal_type = ACPI_BUS_REMOVAL_NORMAL;
+	device_id++;
+	return 0;
 }
 
 static void acpi_device_unregister(struct acpi_device *device, int type)
@@ -1041,7 +1095,7 @@ acpi_add_single_object(struct acpi_devic
 
 	acpi_device_get_debug_info(device, handle, type);
 
-	acpi_device_register(device, parent);
+	result = acpi_device_register(device, parent);
 
       end:
 	if (!result)
Signature · 1 line
1.4.4.g59427
author
#14 lore raw

Re: [PATCH 13/13] ACPI: use unique number as bus_id of ACPI device in sysfs

Quoted 8 lines · Len Brown

From: Zhang Rui <[email protected]>

Previously we used the device name in the DSDT, but would crash upon encountering a duplicate. Also, exposing the DSDT device name to the user in a path isn't a good idea, becauase it is arbitrary.
So just add two attributes for each device,
the full pathname in ACPI namespace and hardware_id.

While this addresses the potential name conflict of the previous version, I think this needs some work.

$ ls /sys/devices/0
1  10  2  3  4  5  57  6  7  8  9  bus  hid  path  power  subsystem  uevent

Assigning the unique numbers in a depth-first search leaves irritating gaps -- (see 10 and 57 above). Instance numbers need to be per-directory.

Also, IMHO, the numbers by themselves look a little strange, maybe dev0, dev1, dev%d etc. wouldn't look so strange?

Also, the ACPI spec has some pre-defined root name-spaces, and I think it makes sense to look up the device name against a small table of those reserved names and print something more interesting than a number.

eg.
_SB system_bus
_PR processors
_TZ thermal_zones
_SI system_indicators
_GPE events

thanks,
-Len

reviewer
#15 lore raw

Re: [PATCH 13/13] ACPI: use unique number as bus_id of ACPI device in sysfs

Quoted 10 lines · Len Brown
Quoted 8 lines · Len Brown

From: Zhang Rui <[email protected]>

Previously we used the device name in the DSDT, but would crash upon encountering a duplicate. Also, exposing the DSDT device name to the user in a path isn't a good idea, becauase it is arbitrary.
So just add two attributes for each device,
the full pathname in ACPI namespace and hardware_id.

Quoted 8 lines

While this addresses the potential name conflict of the previous version, I think this needs some work.

$ ls /sys/devices/0
1  10  2  3  4  5  57  6  7  8  9  bus  hid  path  power  subsystem  uevent

Assigning the unique numbers in a depth-first search leaves irritating gaps -- (see 10 and 57 above).

That's true.
But you know, ACPI namespace is a tree in nature. Depth-first is the fastest way to traverse the ACPI namespace.

Quoted 2 lines

Instance numbers need to be per-directory.

instance numbers should be unique in the whole ACPI bus, as all of them are linked to /sys/bus/acpi/devices/.

Quoted 3 lines

Also, IMHO, the numbers by themselves look a little strange, maybe dev0, dev1, dev%d etc. wouldn't look so strange?

Yes, I can do that. :)

Quoted 5 lines

Also, the ACPI spec has some pre-defined root name-spaces, and I think it makes sense to look up the device name against a small table of those reserved names and print something more interesting than a number.

Quoted 7 lines

eg.
_SB system_bus
_PR processors
_TZ thermal_zones
_SI system_indicators
_GPE events

Yeah. I can do that. But few devices can benefit from this. :(.

BTW: Maybe I can generate a patch to get the following result:
Five devices with the fixed name shown above if they are declared in the BIOS
And add a prefix for every devices, the prefix is one of fixed names, _SB _PR _TZ _SI _GPE. So devices are shown like _SB:dev001, _TZ:dev001, _PR:dev033 etc.
But does this make sense? :(

The best way is to define a unique and meaning rule to name all the ACPI devices. Unfortunately we haven't reached an agreement until now, but I think we can leave this for further discussion.

Quoted 2 lines

thanks,
-Len

reviewer
#16 lore raw

Re: [PATCH 13/13] ACPI: use unique number as bus_id of ACPI device in sysfs

Quoted 23 lines
Quoted 5 lines

Also, the ACPI spec has some pre-defined root name-spaces, and I think it makes sense to look up the device name against a small table of those reserved names and print something more interesting than a number.

Quoted 7 lines

eg.
_SB system_bus
_PR processors
_TZ thermal_zones
_SI system_indicators
_GPE events

Yeah. I can do that. But few devices can benefit from this. :(.

BTW: Maybe I can generate a patch to get the following result:
Five devices with the fixed name shown above if they are declared in the BIOS
And add a prefix for every devices, the prefix is one of fixed names, _SB _PR _TZ _SI _GPE. So devices are shown like _SB:dev001, _TZ:dev001, _PR:dev033 etc.
But does this make sense? :(

Quoted 3 lines

The best way is to define a unique and meaning rule to name all the ACPI devices. Unfortunately we haven't reached an agreement until now, but I think we can leave this for further discussion.

Another way to fix this naming problem.
Many devices in ACPI namespace is meaningless. Only the devices with a PNPID are physical devices and should be exported to userspace. So we can only register these devices and use "PNPID:instance no" as its name.
Add instance_no in struct acpi_device. Every time we fail to register an ACPI device and get an error of "-EEXIST", loop acpi_device_list to get the right instance_no and register again.

Thanks,
Ray

author
#19 lore raw

Re: [PATCH 13/13] ACPI: use unique number as bus_id of ACPI device in sysfs

In reply to Zhang Rui
Quoted 10 lines
Quoted 9 lines

While this addresses the potential name conflict of the previous version, I think this needs some work.

$ ls /sys/devices/0
1  10  2  3  4  5  57  6  7  8  9  bus  hid  path  power  subsystem  uevent

Assigning the unique numbers in a depth-first search leaves irritating gaps -- (see 10 and 57 above).

Quoted 8 lines

That's true.
But you know, ACPI namespace is a tree in nature. Depth-first is the fastest way to traverse the ACPI namespace.

Quoted 2 lines

Instance numbers need to be per-directory.

instance numbers should be unique in the whole ACPI bus, as all of them are linked to /sys/bus/acpi/devices/.

In sysfs, a directory is a kernel/user API.
A user-program will want to open directory entries by name, and the names should make some sense.

The names in /sys/bus/acpi/devices/ and the names in /sys/devices do not have to be the same.

Quoted 19 lines
Quoted 3 lines

Also, IMHO, the numbers by themselves look a little strange, maybe dev0, dev1, dev%d etc. wouldn't look so strange?

Yes, I can do that. :)

Quoted 5 lines

Also, the ACPI spec has some pre-defined root name-spaces, and I think it makes sense to look up the device name against a small table of those reserved names and print something more interesting than a number.

Quoted 7 lines

eg.
_SB system_bus
_PR processors
_TZ thermal_zones
_SI system_indicators
_GPE events

Yeah. I can do that. But few devices can benefit from this. :(.

Quoted 7 lines

BTW: Maybe I can generate a patch to get the following result:
Five devices with the fixed name shown above if they are declared in the BIOS
And add a prefix for every devices, the prefix is one of fixed names, _SB _PR _TZ _SI _GPE. So devices are shown like _SB:dev001, _TZ:dev001, _PR:dev033 etc.
But does this make sense? :(

No. My point is that if it a _TZ then we know that it is a "thermal_zone" an we can just print "thermal_zone". There is no reason to make this cryptic by using the ACPI device names -- they have fixed definitions and in these few cases we can take advantage of that.

Quoted 3 lines

The best way is to define a unique and meaning rule to name all the ACPI devices. Unfortunately we haven't reached an agreement until now, but I think we can leave this for further discussion.

see next message.

author
#17 lore raw

Re: [PATCH 13/13] ACPI: use unique number as bus_id of ACPI device in sysfs

In reply to Zhang Rui
Quoted 9 lines

Another way to fix this naming problem.
Many devices in ACPI namespace is meaningless. Only the devices with a PNPID are physical devices and should be exported to userspace. So we can only register these devices and use "PNPID:instance no" as its name.
Add instance_no in struct acpi_device. Every time we fail to register an ACPI device and get an error of "-EEXIST", loop acpi_device_list to get the right instance_no and register again.

Yes, PNP-id's have definitions, and when we have the luxury of having devices with PNP-id's, we should use those, along with an instance number to handle the case of multiple devices of the PNPid.

Indeed, the question is if we should go so far as to translate the PNPid into English, or simply use the PNPid string.

eg "PNP0C0C" vs "button".

I vote for the PNPid, since it requires less maintenance:-)

thanks,
-Len

reviewer
#18 lore raw

Re: [PATCH 13/13] ACPI: use unique number as bus_id of ACPI device in sysfs

Quoted 13 lines · Len Brown
Quoted 8 lines

Another way to fix this naming problem.
Many devices in ACPI namespace is meaningless. Only the devices with a PNPID are physical devices and should be exported to userspace. So we can only register these devices and use "PNPID:instance no" as its name.
Add instance_no in struct acpi_device. Every time we fail to register an ACPI device and get an error of "-EEXIST", loop acpi_device_list to get the right instance_no and register again.

Yes, PNP-id's have definitions, and when we have the luxury of having devices with PNP-id's, we should use those, along with an instance number to handle the case of multiple devices of the PNPid.

Quoted 7 lines

Indeed, the question is if we should go so far as to translate the PNPid into English, or simply use the PNPid string.

eg "PNP0C0C" vs "button".

I vote for the PNPid, since it requires less maintenance:-)

Yes.
For now, we can use "pnpid:instance_no" for devices with pnpid. For devices without PNPid, we recognise them as "NO_PNPID:instance_no". Is this OK?

Quoted 2 lines

thanks,
-Len

reviewer
#20 lore raw

updated patches of sysfs branch

In reply to Len Brown
Quoted 9 lines

The following patches are on the "sysfs" branch of the ACPI git tree.

To test, apply this e-mail series, or git pull from here:

git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6.git sysfs

I am hopeful that this series will settle down and make the test branch shortly, and thus make its way into an upcoming -mm release, and then upstream.

These are updated patches against 2.6.19. Len, could you update them in sysfs branch please?

Four patches are refreshed in all.
[PATCH 4]: ACPI: add ACPI bus_type for driver model
remove parameter "int state" of battery driver .resume method, which is
added recently.
[PATCH 11]: ACPI: Convert ACPI PCI .bind/.unbind to use PCI bridge
driver
remove useless codes and comments which is shown in last patch.
[PATCH 13]: ACPI: use unique number as bus_id of ACPI devices in sysfs
use "PNPID:instance_no" as bus_id of ACPI devices in sysfs instead of
unique numbers.
[PATCH 14]: ACPI: ibm_acpi: don't use '/' in driver names
We add a new patch in this patch series.
ibm_acpi uses '/' in driver names, and this causes a failure when register an ibm_acpi driver. This patch replace '/' with '_' in driver names.
Thank Henrique de Moraes Holschuh for generating this patch.

Thanks,
Ray

Add ACPI bus_type for Linux driver model.

1. .shutdown method is added into acpi_driver.ops
needed by bus_type operations.
2. remove useless parameter 'int state' in .resume method.
3. change parameter 'int state'
to 'pm_message_t state' in .suspend method.

Note: The new .uevent method mark ACPI drivers by PNPID instead of by name.
Udev script needs to look for "HWID=" or "COMPTID=" to load ACPI drivers as a result.

---
 drivers/acpi/battery.c  |    4 -
 drivers/acpi/fan.c      |    8 +-
 drivers/acpi/scan.c     |  158 +++++++++++++++++++++++++++---------------------
 drivers/acpi/thermal.c  |    4 -
 include/acpi/acpi_bus.h |    9 +-
 5 files changed, 105 insertions(+), 78 deletions(-)
drivers/acpi/fan.c +4 -4
Index: linux-2.6.19/drivers/acpi/fan.c
===================================================================
@@ -48,8 +48,8 @@ MODULE_LICENSE("GPL");
 
 static int acpi_fan_add(struct acpi_device *device);
 static int acpi_fan_remove(struct acpi_device *device, int type);
-static int acpi_fan_suspend(struct acpi_device *device, int state);
-static int acpi_fan_resume(struct acpi_device *device, int state);
+static int acpi_fan_suspend(struct acpi_device *device, pm_message_t state);
+static int acpi_fan_resume(struct acpi_device *device);
 
 static struct acpi_driver acpi_fan_driver = {
 	.name = ACPI_FAN_DRIVER_NAME,
@@ -238,7 +238,7 @@ static int acpi_fan_remove(struct acpi_d
 	return 0;
 }
 
-static int acpi_fan_suspend(struct acpi_device *device, int state)
+static int acpi_fan_suspend(struct acpi_device *device, pm_message_t state)
 {
 	if (!device)
 		return -EINVAL;
@@ -248,7 +248,7 @@ static int acpi_fan_suspend(struct acpi_
 	return AE_OK;
 }
 
-static int acpi_fan_resume(struct acpi_device *device, int state)
+static int acpi_fan_resume(struct acpi_device *device)
 {
 	int result = 0;
 	int power_state = 0;
drivers/acpi/scan.c +91 -67

205 lines not on this page · raw message

drivers/acpi/thermal.c +2 -2
Index: linux-2.6.19/drivers/acpi/thermal.c
===================================================================
@@ -82,7 +82,7 @@ MODULE_PARM_DESC(tzp, "Thermal zone poll
 
 static int acpi_thermal_add(struct acpi_device *device);
 static int acpi_thermal_remove(struct acpi_device *device, int type);
-static int acpi_thermal_resume(struct acpi_device *device, int state);
+static int acpi_thermal_resume(struct acpi_device *device);
 static int acpi_thermal_state_open_fs(struct inode *inode, struct file *file);
 static int acpi_thermal_temp_open_fs(struct inode *inode, struct file *file);
 static int acpi_thermal_trip_open_fs(struct inode *inode, struct file *file);
@@ -1356,7 +1356,7 @@ static int acpi_thermal_remove(struct ac
 	return 0;
 }
 
-static int acpi_thermal_resume(struct acpi_device *device, int state)
+static int acpi_thermal_resume(struct acpi_device *device)
 {
 	struct acpi_thermal *tz = NULL;
 	int i;
include/acpi/acpi_bus.h +6 -3
Index: linux-2.6.19/include/acpi/acpi_bus.h
===================================================================
@@ -92,13 +92,14 @@ typedef int (*acpi_op_remove) (struct ac
 typedef int (*acpi_op_lock) (struct acpi_device * device, int type);
 typedef int (*acpi_op_start) (struct acpi_device * device);
 typedef int (*acpi_op_stop) (struct acpi_device * device, int type);
-typedef int (*acpi_op_suspend) (struct acpi_device * device, int state);
-typedef int (*acpi_op_resume) (struct acpi_device * device, int state);
+typedef int (*acpi_op_suspend) (struct acpi_device * device, pm_message_t state);
+typedef int (*acpi_op_resume) (struct acpi_device * device);
 typedef int (*acpi_op_scan) (struct acpi_device * device);
 typedef int (*acpi_op_bind) (struct acpi_device * device);
 typedef int (*acpi_op_unbind) (struct acpi_device * device);
 typedef int (*acpi_op_match) (struct acpi_device * device,
 			      struct acpi_driver * driver);
+typedef int (*acpi_op_shutdown) (struct acpi_device * device);
 
 struct acpi_bus_ops {
 	u32 acpi_op_add:1;
@@ -112,7 +113,8 @@ struct acpi_bus_ops {
 	u32 acpi_op_bind:1;
 	u32 acpi_op_unbind:1;
 	u32 acpi_op_match:1;
-	u32 reserved:21;
+	u32 acpi_op_shutdown:1;
+	u32 reserved:20;
 };
 
 struct acpi_device_ops {
@@ -127,6 +129,7 @@ struct acpi_device_ops {
 	acpi_op_bind bind;
 	acpi_op_unbind unbind;
 	acpi_op_match match;
+	acpi_op_shutdown shutdown;
 };
 
 struct acpi_driver {
drivers/acpi/battery.c +2 -2
Index: linux-2.6.19/drivers/acpi/battery.c
===================================================================
@@ -64,7 +64,7 @@ extern void *acpi_unlock_battery_dir(str
 
 static int acpi_battery_add(struct acpi_device *device);
 static int acpi_battery_remove(struct acpi_device *device, int type);
-static int acpi_battery_resume(struct acpi_device *device, int status);
+static int acpi_battery_resume(struct acpi_device *device);
 
 static struct acpi_driver acpi_battery_driver = {
 	.name = ACPI_BATTERY_DRIVER_NAME,
@@ -756,7 +756,7 @@ static int acpi_battery_remove(struct ac
 }
 
 /* this is needed to learn about changes made in suspended state */
-static int acpi_battery_resume(struct acpi_device *device, int state)
+static int acpi_battery_resume(struct acpi_device *device)
 {
 	struct acpi_battery *battery;
 

acpi_device had a .bind/.unbind methods, but Linux driver model does not. Cut ACPI PCI code over to use the Linux driver model methods.

Convert bind/unbind to use a new pci bridge driver. The driver will add/remove _PRT, so we can eventually remove .bind/.unbind methods.

---
 drivers/acpi/pci_bind.c |   56 ++++++++++++++++++++++++++++++++++++++++++++----
 drivers/acpi/pci_root.c |    5 ----
 drivers/acpi/scan.c     |   17 --------------
 3 files changed, 52 insertions(+), 26 deletions(-)
drivers/acpi/pci_bind.c +52 -4

71 lines not on this page · raw message

drivers/acpi/pci_root.c +0 -5
Index: linux-2.6.19/drivers/acpi/pci_root.c
===================================================================
@@ -175,11 +175,6 @@ static int acpi_pci_root_add(struct acpi
 	strcpy(acpi_device_class(device), ACPI_PCI_ROOT_CLASS);
 	acpi_driver_data(device) = root;
 
-	/*
-	 * TBD: Doesn't the bus driver automatically set this?
-	 */
-	device->ops.bind = acpi_pci_bind;
-
 	/* 
 	 * Segment
 	 * -------
drivers/acpi/scan.c +0 -17
Index: linux-2.6.19/drivers/acpi/scan.c
===================================================================
@@ -866,11 +866,6 @@ static int acpi_bus_remove(struct acpi_d
 	if (!rmdevice)
 		return 0;
 
-	if (dev->flags.bus_address) {
-		if ((dev->parent) && (dev->parent->ops.unbind))
-			dev->parent->ops.unbind(dev);
-	}
-
 	acpi_device_unregister(dev, ACPI_BUS_REMOVAL_EJECT);
 
 	return 0;
@@ -987,18 +982,6 @@ acpi_add_single_object(struct acpi_devic
 
 	acpi_device_register(device, parent);
 
-	/*
-	 * Bind _ADR-Based Devices
-	 * -----------------------
-	 * If there's a a bus address (_ADR) then we utilize the parent's 
-	 * 'bind' function (if exists) to bind the ACPI- and natively-
-	 * enumerated device representations.
-	 */
-	if (device->flags.bus_address) {
-		if (device->parent && device->parent->ops.bind)
-			device->parent->ops.bind(device);
-	}
-
       end:
 	if (!result)
 		*child = device;

Previously we used the device name in the DSDT, but would crash upon encountering a duplicate. Also, exposing the DSDT device name to the user in a patch isn't a good idea, because it is arbitrary.

After some discussion, we finally decided to use "PNPID:instance_no" as the bus_id of ACPI devices.

Two attributes for each device are added at the same time, the full pathname in ACPI namespace and hardware_id if it has.

NOTE: acpi_bus_id_list is used to keep the information of PNPID
and instance number of the given PNPID. Loop the
acpi_bus_id_list to find the instance_no of the same PNPID
when register a device. If failed, i.e. we don't have a node with this PNPID, allocate one and link it to this list.

NOTE: Now I don't take the memory free work in charge.
If necessary, I can add a reference count in struct acpi_device_bus_id, and check the reference and when unregister a device, i.e. memory is freed when the reference count of a given PNPID is 0.

---
 drivers/acpi/scan.c |  103 +++++++++++++++++++++++++++++++++++++++++++++++-----
 1 files changed, 94 insertions(+), 9 deletions(-)
drivers/acpi/scan.c +94 -9

161 lines not on this page · raw message

ibm-acpi uses sub-device names like ibm/hotkey, which get in the way of a sysfs conversion. Fix it to use ibm_hotkey instead. Thanks to Zhang Rui for noticing this.

---

 drivers/acpi/ibm_acpi.c |    2 +-
 1 files changed, 1 insertion(+), 1 deletion(-)
drivers/acpi/ibm_acpi.c +1 -1
Index: linux-2.6.19/drivers/acpi/ibm_acpi.c
===================================================================
@@ -1825,7 +1825,7 @@ static int __init register_driver(struct
 	}
 
 	memset(ibm->driver, 0, sizeof(struct acpi_driver));
-	sprintf(ibm->driver->name, "%s/%s", IBM_NAME, ibm->name);
+	sprintf(ibm->driver->name, "%s_%s", IBM_NAME, ibm->name);
 	ibm->driver->ids = ibm->hid;
 	ibm->driver->ops.add = &ibm_device_add;