Skip to contentSkip to conversation

BUG, 2.6.20-rc3 raid autodetection

DISCUSSION Kasper Sandberg 3 participants 5 messages Jan 4, 2007 5 messages not in the archive

lore
Share & tools
lore
#0 lore raw

Hello.

i just attempted to test .20-rc3-git4 on a box, which has 6 drives in raid5. it uses raid autodetection, and 2 ide controllers (via and promise 20269).

there are two problems.

first, and most importantly, it doesent autodetect, i attempted with both the old ide drivers, and the new pata on libata drivers, the drives appears to be found, but the raid autoassembling just doesent happen.

this is .17, which works:
http://sh.nu/p/8001

this is .20-rc3-git4 which doesent work, in pata-on-libata mode:
http://sh.nu/p/8000

this is .20-rc3-git4 which doesent work, in old ide mode:
http://sh.nu/p/8002

second bug:
notice on these pastes the lines at bottom, the keyboard stuff, these are repeated constantly, and caps/scrolllock button on keyboard is blinking.

mvh.
Kasper Sandberg

#1 lore raw
Quoted 12 lines · Kasper Sandberg

Hello.

i just attempted to test .20-rc3-git4 on a box, which has 6 drives in raid5. it uses raid autodetection, and 2 ide controllers (via and promise 20269).

there are two problems.

first, and most importantly, it doesent autodetect, i attempted with both the old ide drivers, and the new pata on libata drivers, the drives appears to be found, but the raid autoassembling just doesent happen.

Quoted 8 lines

this is .17, which works:
http://sh.nu/p/8001

this is .20-rc3-git4 which doesent work, in pata-on-libata mode:
http://sh.nu/p/8000

this is .20-rc3-git4 which doesent work, in old ide mode:
http://sh.nu/p/8002

For some reason IDE disk driver is not claiming IDE devices.

Could you please double check that IDE disk driver is built-in (CONFIG_BLK_DEV_IDEDISK=y in the kernel configuration) and not compiled as module?

Bart

#2 lore raw
Quoted 19 lines · Bartlomiej Zolnierkiewicz
Quoted 18 lines · Kasper Sandberg

Hello.

i just attempted to test .20-rc3-git4 on a box, which has 6 drives in raid5. it uses raid autodetection, and 2 ide controllers (via and promise 20269).

there are two problems.

first, and most importantly, it doesent autodetect, i attempted with both the old ide drivers, and the new pata on libata drivers, the drives appears to be found, but the raid autoassembling just doesent happen.

this is .17, which works:
http://sh.nu/p/8001

this is .20-rc3-git4 which doesent work, in pata-on-libata mode:
http://sh.nu/p/8000

Quoted 8 lines
Quoted 2 lines

this is .20-rc3-git4 which doesent work, in old ide mode:
http://sh.nu/p/8002

For some reason IDE disk driver is not claiming IDE devices.

Could you please double check that IDE disk driver is built-in (CONFIG_BLK_DEV_IDEDISK=y in the kernel configuration) and not compiled as module?

i need not check even once, i do not have module support enabled, so everything 1000000% surely is built in. this is the case for .17 too (and earlier, this box was started with .15 i think.)

Quoted 3 lines

Bart

#8 lore raw
In reply to a message not in the archive
Quoted 59 lines · Bartlomiej Zolnierkiewicz
Quoted 51 lines · Kasper Sandberg
Quoted 50 lines · Bartlomiej Zolnierkiewicz
Quoted 34 lines · Kasper Sandberg
Quoted 33 lines · Bartlomiej Zolnierkiewicz
Quoted 23 lines · Kasper Sandberg
Quoted 22 lines · Bartlomiej Zolnierkiewicz
Quoted 20 lines · Kasper Sandberg

Hello.

i just attempted to test .20-rc3-git4 on a box, which has 6 drives in raid5. it uses raid autodetection, and 2 ide controllers (via and promise 20269).

there are two problems.

first, and most importantly, it doesent autodetect, i attempted with both the old ide drivers, and the new pata on libata drivers, the drives appears to be found, but the raid autoassembling just doesent happen.

this is .17, which works:
http://sh.nu/p/8001

this is .20-rc3-git4 which doesent work, in pata-on-libata mode:
http://sh.nu/p/8000

this is .20-rc3-git4 which doesent work, in old ide mode:
http://sh.nu/p/8002

Quoted 6 lines
Quoted 5 lines

For some reason IDE disk driver is not claiming IDE devices.

Could you please double check that IDE disk driver is built-in (CONFIG_BLK_DEV_IDEDISK=y in the kernel configuration) and not compiled as module?

i need not check even once, i do not have module support enabled, so

OK

Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

everything 1000000% surely is built in. this is the case for .17 too (and earlier, this box was started with .15 i think.)

Could you send me your config?
I'll try to reproduce this locally.

sure thing.

http://sh.nu/p/8004 <-- .17 working

CONFIG_BLK_DEV_IDEDISK=y

Quoted 3 lines

http://sh.nu/p/8005 <-- .20-rc3-git4 nonworking, idemode, the one with libata i dont have anymore, but the only difference is that i use the libata drivers, but as its same result, shouldnt matter

Quoted 6 lines
Quoted 3 lines

# CONFIG_BLK_DEV_IDEDISK is not set

so not everything is "1000000% surely" built-in ;)

i see your point, im afraid i may have misinterpreted you, since you said "and not compiled as module", so i thought you meant i had to make sure it wasnt moduled only.

Quoted 5 lines

You were right - I forgot about "CONFIG_BLK_DEV_IDEDISK=n" case.

Quoted 1 line

i will try with this now, what about pataonlibata, do i need this for

Please report if this fixes the issue.

yeah it did.

Quoted 7 lines
Quoted 2 lines

that too?

for libata you need SCSI disk driver: CONFIG_BLK_DEV_SD=y

[ libata is not independent subsystem like IDE but depends on SCSI,
and I really don't know why this is not mentioned in config help ]

i knew that, i just thought it may select what it required, though i can see that it isnt strictly required, just what one wishes often. :)

thanks for your help, will try with libata now.

Quoted 1 line
#9 lore raw

Re: BUG, 2.6.20-rc3 raid autodetection [repost due to forgotten CC]

In reply to a message not in the archive
Quoted 63 lines · Kasper Sandberg
Quoted 46 lines · Bartlomiej Zolnierkiewicz
Quoted 34 lines · Kasper Sandberg
Quoted 33 lines · Bartlomiej Zolnierkiewicz
Quoted 23 lines · Kasper Sandberg
Quoted 22 lines · Bartlomiej Zolnierkiewicz
Quoted 20 lines · Kasper Sandberg

Hello.

i just attempted to test .20-rc3-git4 on a box, which has 6 drives in raid5. it uses raid autodetection, and 2 ide controllers (via and promise 20269).

there are two problems.

first, and most importantly, it doesent autodetect, i attempted with both the old ide drivers, and the new pata on libata drivers, the drives appears to be found, but the raid autoassembling just doesent happen.

this is .17, which works:
http://sh.nu/p/8001

this is .20-rc3-git4 which doesent work, in pata-on-libata mode:
http://sh.nu/p/8000

this is .20-rc3-git4 which doesent work, in old ide mode:
http://sh.nu/p/8002

Quoted 6 lines
Quoted 5 lines

For some reason IDE disk driver is not claiming IDE devices.

Could you please double check that IDE disk driver is built-in (CONFIG_BLK_DEV_IDEDISK=y in the kernel configuration) and not compiled as module?

i need not check even once, i do not have module support enabled, so

OK

Quoted 8 lines
Quoted 5 lines
Quoted 2 lines

everything 1000000% surely is built in. this is the case for .17 too (and earlier, this box was started with .15 i think.)

Could you send me your config?
I'll try to reproduce this locally.

sure thing.

http://sh.nu/p/8004 <-- .17 working

CONFIG_BLK_DEV_IDEDISK=y

Quoted 7 lines
Quoted 3 lines

http://sh.nu/p/8005 <-- .20-rc3-git4 nonworking, idemode, the one with libata i dont have anymore, but the only difference is that i use the libata drivers, but as its same result, shouldnt matter

# CONFIG_BLK_DEV_IDEDISK is not set

so not everything is "1000000% surely" built-in ;)

i see your point, im afraid i may have misinterpreted you, since you said "and not compiled as module", so i thought you meant i had to make sure it wasnt moduled only.

i will try with this now, what about pataonlibata, do i need this for that too?

Quoted 3 lines

Bart

Signature · 1 line
Redeeman <[email protected]>