ARM: OMAP: Board updates and additions for OMAP2

PATCH In review Tony Lindgren 1 participant 9 messages Apr 9, 2007 – Apr 16, 2007

Subsystems (4)

Arm (32-bit) Arm sub-architectures OMAP2+ support OMAP power management support

lore

Share & tools

lore

Tony Lindgren

author maintainer

2007-04-09 21:34 UTC #0 lore raw

cover ARM: OMAP: Board updates and additions for OMAP2

Hi,

The following patch series contains updates board updates and additions for OMAP2 code.

This is take #2 of the earlier 90 patch mountain, which has been split into six smaller series.

Regards,

Tony

Tony Lindgren

author maintainer

2007-04-09 21:35 UTC #1 lore raw

PATCH 1/7 ARM: OMAP: USB peripheral support on H4

From: David Brownell <[email protected]>

H4 has two peripheral ports, one for "download" and one for OTG. The one to use is selected through Kconfig.

Signed-off-by David Brownell <[email protected]>

Signed-off-by Tony Lindgren <[email protected]>

---
 arch/arm/mach-omap2/Kconfig    |   21 ++++++++++++++++++
 arch/arm/mach-omap2/board-h4.c |   46 ++++++++++++++++++++++++++++++++++++++++
 2 files changed, 67 insertions(+), 0 deletions(-)

arch/arm/mach-omap2/Kconfig +21 -0

Index: linux-2.6/arch/arm/mach-omap2/Kconfig
===================================================================
@@ -27,6 +27,27 @@ config MACH_OMAP_H4
 	depends on ARCH_OMAP2 && ARCH_OMAP24XX
 	select OMAP_DEBUG_DEVICES
 
+config MACH_OMAP_H4_OTG
+	bool "Use USB OTG connector, not device connector (S1.10)"
+	depends on MACH_OMAP_H4
+	help
+	  Set this if you've set S1.10 (on the mainboard) to use the
+	  Mini-AB (OTG) connector and OTG transceiver with the USB0
+	  port, instead of the Mini-B ("download") connector with its
+	  non-OTG transceiver.
+
+	  Note that the "download" connector can be used to bootstrap
+	  the system from the OMAP mask ROM.  Also, since this is a
+	  development platform, you can also force the OTG port into
+	  a non-OTG operational mode.
+
+config MACH_OMAP2_H4_USB1
+	bool "Use USB1 port, not UART2 (S3.3)"
+	depends on MACH_OMAP_H4
+	help
+	  Set this if you've set SW3.3 (on the CPU card) so that the
+	  expansion connectors receive USB1 signals instead of UART2.
+
 config MACH_OMAP_APOLLON
 	bool "OMAP 2420 Apollon board"
 	depends on ARCH_OMAP2 && ARCH_OMAP24XX

arch/arm/mach-omap2/board-h4.c +46 -0

69 lines not on this page · raw message

Tony Lindgren

author maintainer

2007-04-09 21:35 UTC #2 lore raw

PATCH 2/7 ARM: OMAP: Fix typo in board-h4.h

From: Komal Shah <[email protected]>

Replace OMAP1610 with OMAP2420.

Signed-off-by Komal Shah <[email protected]>

Signed-off-by Tony Lindgren <[email protected]>

---
 include/asm-arm/arch-omap/board-h4.h |    2 +-
 1 files changed, 1 insertions(+), 1 deletions(-)

include/asm-arm/arch-omap/board-h4.h +1 -1

@@ -1,7 +1,7 @@
 /*
  * linux/include/asm-arm/arch-omap/board-h4.h
  *
- * Hardware definitions for TI OMAP1610 H4 board.
+ * Hardware definitions for TI OMAP2420 H4 board.
  *
  * Initial creation by Dirk Behme <[email protected]>
  *

Signature · 1 line

1.4.4.2

Tony Lindgren

author maintainer

2007-04-09 21:37 UTC #3 lore raw

PATCH 3/7 ARM: OMAP: Sync H4 board init with linux-omap

This patch syncs H4 board init with linux-omap tree.

Signed-off-by Tony Lindgren <[email protected]>

---
 arch/arm/mach-omap2/board-h4.c        |  180 +++++++++++++++++++++++++++++++--
 10 files changed, 380 insertions(+), 176 deletions(-)

arch/arm/mach-omap2/board-h4.c +170 ~~-10~~

@@ -19,6 +19,8 @@
 #include <linux/delay.h>
 #include <linux/workqueue.h>
 #include <linux/input.h>
+#include <linux/err.h>
+#include <linux/clk.h>
 
 #include <asm/hardware.h>
 #include <asm/mach-types.h>

@@ -36,10 +38,14 @@
 #include <asm/arch/keypad.h>
 #include <asm/arch/menelaus.h>
 #include <asm/arch/dma.h>
+#include <asm/arch/gpmc.h>
 #include "prcm-regs.h"
 
 #include <asm/io.h>
 
+#define H4_FLASH_CS	0
+#define H4_SMC91X_CS	1
+
 static unsigned int row_gpios[6] = { 88, 89, 124, 11, 6, 96 };
 static unsigned int col_gpios[7] = { 90, 91, 100, 36, 12, 97, 98 };

@@ -116,8 +122,6 @@ static struct flash_platform_data h4_flash_data = {
 };
 
 static struct resource h4_flash_resource = {
-	.start		= H4_CS0_BASE,
-	.end		= H4_CS0_BASE + SZ_64M - 1,
 	.flags		= IORESOURCE_MEM,
 };

@@ -133,6 +137,7 @@ static struct platform_device h4_flash_device = {
 
 /* Select between the IrDA and aGPS module
  */
+#if defined(CONFIG_OMAP_IR) || defined(CONFIG_OMAP_IR_MODULE)
 static int h4_select_irda(struct device *dev, int state)
 {
 	unsigned char expa;

@@ -192,6 +197,10 @@ static int h4_transceiver_mode(struct device *dev, int mode)
 
 	return 0;
 }
+#else
+static int h4_select_irda(struct device *dev, int state) { return 0; }
+static int h4_transceiver_mode(struct device *dev, int mode) { return 0; }
+#endif
 
 static struct omap_irda_config h4_irda_data = {
 	.transceiver_cap	= IR_SIRMODE | IR_MIRMODE | IR_FIRMODE,

@@ -253,16 +262,80 @@ static struct platform_device *h4_devices[] __initdata = {
 	&h4_lcd_device,
 };
 
+/* 2420 Sysboot setup (2430 is different) */
+static u32 get_sysboot_value(void)
+{
+	return (omap_readl(OMAP242X_CONTROL_STATUS) & 0xFFF);
+}
+
+/* FIXME: This function should be moved to some other file, gpmc.c? */
+
+/* H4-2420's always used muxed mode, H4-2422's always use non-muxed
+ *
+ * Note: OMAP-GIT doesn't correctly do is_cpu_omap2422 and is_cpu_omap2423
+ *  correctly.  The macro needs to look at production_id not just hawkeye.
+ */
+static u32 is_gpmc_muxed(void)
+{
+	u32 mux;
+	mux = get_sysboot_value();
+	if ((mux & 0xF) == 0xd)
+		return 1;	/* NAND config (could be either) */
+	if (mux & 0x2)		/* if mux'ed */
+		return 1;
+	else
+		return 0;
+}
+
 static inline void __init h4_init_debug(void)
 {
+	int eth_cs;
+	unsigned long cs_mem_base;
+	unsigned int muxed, rate;
+	struct clk *l3ck;
+
+	eth_cs	= H4_SMC91X_CS;
+
+	l3ck = clk_get(NULL, "core_l3_ck");
+	if (IS_ERR(l3ck))
+		rate = 100000000;
+	else
+		rate = clk_get_rate(l3ck);
+
+	if (is_gpmc_muxed())
+		muxed = 0x200;
+	else
+		muxed = 0;
+
 	/* Make sure CS1 timings are correct */
-	GPMC_CONFIG1_1 = 0x00011200;
-	GPMC_CONFIG2_1 = 0x001f1f01;
-	GPMC_CONFIG3_1 = 0x00080803;
-	GPMC_CONFIG4_1 = 0x1c091c09;
-	GPMC_CONFIG5_1 = 0x041f1f1f;
-	GPMC_CONFIG6_1 = 0x000004c4;
-	GPMC_CONFIG7_1 = 0x00000f40 | (0x08000000 >> 24);
+	gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1,
+			  0x00011000 | muxed);
+
+	if (rate >= 160000000) {
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+	} else if (rate >= 130000000) {
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+	} else {/* rate = 100000000 */
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
+	}
+
+	if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
+		printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
+		return;
+	}
+
 	udelay(100);
 
 	omap_cfg_reg(M15_24XX_GPIO92);

@@ -270,11 +343,24 @@ static inline void __init h4_init_debug(void)
 		gpmc_cs_free(eth_cs);
 }
 
+static void __init h4_init_flash(void)
+{
+	unsigned long base;
+
+	if (gpmc_cs_request(H4_FLASH_CS, SZ_64M, &base) < 0) {
+		printk("Can't request GPMC CS for flash\n");
+		return;
+	}
+	h4_flash_resource.start	= base;
+	h4_flash_resource.end	= base + SZ_64M - 1;
+}
+
 static void __init omap_h4_init_irq(void)
 {
 	omap2_init_common_hw();
 	omap_init_irq();
 	omap_gpio_init();
+	h4_init_flash();
 }
 
 static struct omap_uart_config h4_uart_config __initdata = {

@@ -336,9 +422,75 @@ static struct omap_board_config_kernel h4_config[] = {
 	{ OMAP_TAG_UART,	&h4_uart_config },
 	{ OMAP_TAG_MMC,		&h4_mmc_config },
 	{ OMAP_TAG_LCD,		&h4_lcd_config },
-	{ OMAP_TAG_USB,	&h4_usb_config },
+	{ OMAP_TAG_USB,		&h4_usb_config },
 };
 
+#ifdef	CONFIG_MACH_OMAP_H4_TUSB
+
+#include <linux/usb/musb.h>
+
+static struct musb_hdrc_platform_data tusb_data = {
+	.mode		= MUSB_OTG,
+	.min_power	= 25,	/* x2 = 50 mA drawn from VBUS as peripheral */
+
+	/* 1.8V supplied by Menelaus, other voltages supplied by VBAT;
+	 * so no switching.
+	 */
+};
+
+static void __init tusb_evm_setup(void)
+{
+	static char	announce[] __initdata =
+				KERN_INFO "TUSB 6010 EVM\n";
+	int		irq;
+	unsigned	dmachan = 0;
+
+	/* There are at least 32 different combinations of boards that
+	 * are loosely called "H4", with a 2420 ... different OMAP chip
+	 * revisions (with pin mux changes for DMAREQ, GPMC errata, etc),
+	 * modifications of the CPU board, mainboard, EVM, TUSB etc.
+	 * Plus omap2422, omap2423, etc.
+	 *
+	 * So you might need to tweak this setup to make the TUSB EVM
+	 * behave on your particular setup ...
+	 */
+
+	/* Already set up:  GPMC AD[0..15], CLK, nOE, nWE, nADV_ALE */
+	omap_cfg_reg(E2_GPMC_NCS2);
+	omap_cfg_reg(L2_GPMC_NCS7);
+	omap_cfg_reg(M1_GPMC_WAIT2);
+
+	switch ((system_rev >> 8) & 0x0f) {
+	case 0:		/* ES 1.0 */
+	case 1:		/* ES 2.0 */
+		/* Assume early board revision without optional ES2.0
+		 * rework to swap J15 & AA10 so DMAREQ0 works
+		 */
+		omap_cfg_reg(AA10_242X_GPIO13);
+		irq = 13;
+		// omap_cfg_reg(J15_24XX_DMAREQ0);
+		break;
+	default:
+		/* Later Menelaus boards can support all 6 DMA request
+		 * lines, at the price of boot flash A23-A26.
+		 */
+		omap_cfg_reg(J15_24XX_GPIO99);
+		irq = 99;
+		omap_cfg_reg(AA10_242X_DMAREQ0);
+		omap_cfg_reg(AA6_242X_DMAREQ1);
+		dmachan = (1 << 1) | (1 << 0);
+		break;
+	}
+
+	if (tusb6010_setup_interface(&tusb_data,
+			TUSB6010_REFCLK_24, /* waitpin */ 2,
+			/* async cs */ 2, /* sync cs */ 7,
+			irq, dmachan) == 0)
+		printk(announce);
+}
+
+#endif
+
 static void __init omap_h4_init(void)
 {
 	/*

@@ -371,6 +523,14 @@ static void __init omap_h4_init(void)
 	omap_board_config = h4_config;
 	omap_board_config_size = ARRAY_SIZE(h4_config);
 	omap_serial_init();
+
+	/* smc91x, debug leds, ps/2, extra uarts */
+	h4_init_debug();
+
+#ifdef	CONFIG_MACH_OMAP_H4_TUSB
+	tusb_evm_setup();
+#endif
+
 }
 
 static void __init omap_h4_map_io(void)

Signature · 1 line

1.4.4.2

Tony Lindgren

author maintainer

2007-04-09 21:34 UTC #4 lore raw

PATCH 4/7 ARM: OMAP: cleanup apollon board

From: Kyungmin Park <[email protected]>

- Add etherent gpmc handling
- Remove unused mux setting
- Add MMC switch pin comments

Signed-off-by Kyungmin Park <[email protected]>

Signed-off-by Tony Lindgren <[email protected]>

---
 arch/arm/mach-omap2/board-apollon.c |   50 ++++++++++++++++++++++++++--------
 1 files changed, 38 insertions(+), 12 deletions(-)

arch/arm/mach-omap2/board-apollon.c +38 ~~-12~~

@@ -27,6 +27,8 @@
 #include <linux/delay.h>
 #include <linux/leds.h>
 #include <linux/irq.h>
+#include <linux/err.h>
+#include <linux/clk.h>
 
 #include <asm/hardware.h>
 #include <asm/mach-types.h>

@@ -187,16 +189,42 @@ static struct platform_device *apollon_devices[] __initdata = {
 static inline void __init apollon_init_smc91x(void)
 {
 	unsigned long base;
+	unsigned int rate;
+	struct clk *l3ck;
+	int eth_cs;
+
+	l3ck = clk_get(NULL, "core_l3_ck");
+	if (IS_ERR(l3ck))
+		rate = 100000000;
+	else
+		rate = clk_get_rate(l3ck);
+
+	eth_cs = APOLLON_ETH_CS;
 
 	/* Make sure CS1 timings are correct */
-	GPMC_CONFIG1_1 = 0x00011203;
-	GPMC_CONFIG2_1 = 0x001f1f01;
-	GPMC_CONFIG3_1 = 0x00080803;
-	GPMC_CONFIG4_1 = 0x1c091c09;
-	GPMC_CONFIG5_1 = 0x041f1f1f;
-	GPMC_CONFIG6_1 = 0x000004c4;
-
-	if (gpmc_cs_request(APOLLON_ETH_CS, SZ_16M, &base) < 0) {
+	gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1, 0x00011200);
+
+	if (rate >= 160000000) {
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+	} else if (rate >= 130000000) {
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+	} else {/* rate = 100000000 */
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
+	}
+
+	if (gpmc_cs_request(eth_cs, SZ_16M, &base) < 0) {
 		printk(KERN_ERR "Failed to request GPMC CS for smc91x\n");
 		return;
 	}

@@ -208,7 +236,7 @@ static inline void __init apollon_init_smc91x(void)
 	if (omap_request_gpio(APOLLON_ETHR_GPIO_IRQ) < 0) {
 		printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
 			APOLLON_ETHR_GPIO_IRQ);
-		gpmc_cs_free(APOLLON_ETH_CS);
+		gpmc_cs_free(eth_cs);
 		return;
 	}
 	omap_set_gpio_direction(APOLLON_ETHR_GPIO_IRQ, 1);

@@ -232,6 +260,7 @@ static struct omap_mmc_config apollon_mmc_config __initdata = {
 		.wire4		= 1,
 		.wp_pin		= -1,
 		.power_pin	= -1,
+	/* Note: If you want to detect card feature, please assign 37 */
 		.switch_pin	= -1,
 	},
 };

@@ -336,9 +365,6 @@ static void __init omap_apollon_init(void)
 	apollon_flash_init();
 	apollon_usb_init();
 
-	/* REVISIT: where's the correct place */
-	omap_cfg_reg(W19_24XX_SYS_NIRQ);
-
 	/* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
 	CONTROL_DEVCONF |= (1 << 24);

Signature · 1 line

1.4.4.2

Tony Lindgren

author maintainer

2007-04-09 21:36 UTC #5 lore raw

PATCH 5/7 ARM: OMAP: Merge board specific files from N800 tree

From: Kai Svahn <[email protected]>

This patch merges board specific files from N800 tree. Nokia has published the files at:

http://repository.maemo.org/pool/maemo3.0/free/source/
kernel-source-rx-34_2.6.18.orig.tar.gz
kernel-source-rx-34_2.6.18-osso29.diff.gz

Signed-off-by Kai Svahn <[email protected]>

Signed-off-by Tony Lindgren <[email protected]>

arch/arm/mach-omap2/Kconfig +10 -1

Index: linux-2.6/arch/arm/mach-omap2/Kconfig
===================================================================
@@ -54,4 +54,13 @@ config MACH_OMAP_APOLLON
 
 config MACH_OMAP_2430SDP
 	bool "OMAP 2430 SDP board"
-	depends on ARCH_OMAP2 && ARCH_OMAP24XX
\ No newline at end of file
+	depends on ARCH_OMAP2 && ARCH_OMAP24XX
+
+config MACH_NOKIA_N800
+	bool "Nokia N800"
+	depends on ARCH_OMAP24XX
+
+config MACH_OMAP2_TUSB6010
+       bool
+       depends on ARCH_OMAP2 && ARCH_OMAP2420
+       default y if MACH_NOKIA_N800
\ No newline at end of file

arch/arm/mach-omap2/Makefile +4 -0

Index: linux-2.6/arch/arm/mach-omap2/Makefile
===================================================================
@@ -16,4 +16,8 @@ obj-$(CONFIG_MACH_OMAP_GENERIC)		+= boar
 obj-$(CONFIG_MACH_OMAP_H4)		+= board-h4.o
 obj-$(CONFIG_MACH_OMAP_2430SDP)		+= board-2430sdp.o
 obj-$(CONFIG_MACH_OMAP_APOLLON)		+= board-apollon.o
+obj-$(CONFIG_MACH_NOKIA_N800)		+= board-n800.o board-n800-flash.o \
+					   board-n800-mmc.o board-n800-bt.o \
+					   board-n800-audio.o board-n800-usb.o \
+					   board-n800-dsp.o board-n800-pm.o

arch/arm/mach-omap2/board-n800-audio.c new file +366 -0

366 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-bt.c new file +42 -0

42 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-dsp.c new file +156 -0

156 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-flash.c new file +156 -0

156 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-mmc.c new file +282 -0

282 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-pm.c new file +79 -0

79 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-usb.c new file +102 -0

102 lines not on this page · raw message

arch/arm/mach-omap2/board-n800.c new file +515 -0

515 lines not on this page · raw message

include/asm-arm/arch-omap/board.h +22 -2

Index: linux-2.6/include/asm-arm/arch-omap/board.h
===================================================================
@@ -25,9 +25,12 @@
 #define OMAP_TAG_FBMEM		0x4f08
 #define OMAP_TAG_STI_CONSOLE	0x4f09
 #define OMAP_TAG_CAMERA_SENSOR	0x4f0a
+#define OMAP_TAG_PARTITION      0x4f0b
+#define OMAP_TAG_TEA5761	0x4f10
+#define OMAP_TAG_TMP105		0x4f11
 
 #define OMAP_TAG_BOOT_REASON    0x4f80
-#define OMAP_TAG_FLASH_PART	0x4f81
+#define OMAP_TAG_FLASH_PART_STR	0x4f81
 #define OMAP_TAG_VERSION_STR	0x4f82
 
 struct omap_clock_config {

@@ -139,8 +142,25 @@ struct omap_uart_config {
 	unsigned int enabled_uarts;
 };
 
+struct omap_tea5761_config {
+	u16 enable_gpio;
+};
+
+/* This cannot be passed from the bootloader */
+struct omap_tmp105_config {
+	u16 tmp105_irq_pin;
+	int (* set_power)(int enable);
+};
+
+struct omap_partition_config {
+	char name[16];
+	unsigned int size;
+	unsigned int offset;
+	/* same as in include/linux/mtd/partitions.h */
+	unsigned int mask_flags;
+};
 
-struct omap_flash_part_config {
+struct omap_flash_part_str_config {
 	char part_table[0];
 };

include/asm-arm/arch-omap/board-nokia.h +11 -0

Index: linux-2.6/include/asm-arm/arch-omap/board-nokia.h
===================================================================
@@ -11,6 +11,17 @@
 
 #include <linux/types.h>
 
+extern void __init n800_flash_init(void);
+extern void __init n800_mmc_init(void);
+extern void __init n800_bt_init(void);
+extern void __init n800_audio_init(struct tsc2301_platform_data *);
+extern void __init n800_dsp_init(void);
+extern void __init n800_usb_init(void);
+extern void __init n800_pm_init(void);
+extern int n800_audio_enable(struct dsp_kfunc_device *kdev, int stage);
+extern int n800_audio_disable(struct dsp_kfunc_device *kdev, int stage);
+extern void n800_mmc_slot1_cover_handler(void *arg, int state);
+
 #define OMAP_TAG_NOKIA_BT	0x4e01
 #define OMAP_TAG_WLAN_CX3110X	0x4e02
 #define OMAP_TAG_CBUS		0x4e03

include/asm-arm/arch-omap/onenand.h +1 -0

Index: linux-2.6/include/asm-arm/arch-omap/onenand.h
===================================================================
@@ -16,4 +16,5 @@ struct omap_onenand_platform_data {
 	int			gpio_irq;
 	struct mtd_partition	*parts;
 	int			nr_parts;
+	int                     (*onenand_setup)(void __iomem *);
 };

Tony Lindgren

author maintainer

2007-04-09 21:34 UTC #6 lore raw

PATCH 6/7 ARM: OMAP: Replace mach-omap/omap2 with mach-omap2

From: Trilok Soni <[email protected]>

Update board Apollon with correct file path.

Signed-off-by Trilok Soni <[email protected]>

Signed-off-by Tony Lindgren <[email protected]>

---
 arch/arm/mach-omap2/board-apollon.c    |    2 +-
 arch/arm/mach-omap2/usb-tusb6010.c     |    2 +-
 6 files changed, 6 insertions(+), 6 deletions(-)

arch/arm/mach-omap2/board-apollon.c +1 -1

@@ -4,7 +4,7 @@
  * Copyright (C) 2005,2006 Samsung Electronics
  * Author: Kyungmin Park <[email protected]>
  *
- * Modified from mach-omap/omap2/board-h4.c
+ * Modified from mach-omap2/board-h4.c
  *
  * Code for apollon OMAP2 board. Should work on many OMAP2 systems where
  * the bootloader passes the board-specific data to the kernel.

Tony Lindgren

author maintainer

2007-04-09 21:36 UTC #7 lore raw

PATCH 7/7 ARM: OMAP: Add apollon gpio keys using gpio-keys input

From: Kyungmin Park <[email protected]>

Add apollon gpio keys using gpio-keys input

Signed-off-by Kyungmin Park <[email protected]>

Signed-off-by Tony Lindgren <[email protected]>

---
 arch/arm/mach-omap2/Makefile             |    3 +-
 arch/arm/mach-omap2/board-apollon-keys.c |   79 ++++++++++++++++++++++++++++++
 arch/arm/mach-omap2/board-apollon.c      |   53 --------------------
 3 files changed, 81 insertions(+), 54 deletions(-)

arch/arm/mach-omap2/Makefile +2 -1

Index: linux-2.6/arch/arm/mach-omap2/Makefile
===================================================================
@@ -15,7 +15,8 @@ obj-$(CONFIG_PM) += pm.o sleep.o
 obj-$(CONFIG_MACH_OMAP_GENERIC)		+= board-generic.o
 obj-$(CONFIG_MACH_OMAP_H4)		+= board-h4.o
 obj-$(CONFIG_MACH_OMAP_2430SDP)		+= board-2430sdp.o
-obj-$(CONFIG_MACH_OMAP_APOLLON)		+= board-apollon.o
+obj-$(CONFIG_MACH_OMAP_APOLLON)		+= board-apollon.o \
+					   board-apollon-keys.o
 obj-$(CONFIG_MACH_NOKIA_N800)		+= board-n800.o board-n800-flash.o \
 					   board-n800-mmc.o board-n800-bt.o \
 					   board-n800-audio.o board-n800-usb.o \

arch/arm/mach-omap2/board-apollon-keys.c new file +79 -0

79 lines not on this page · raw message

arch/arm/mach-omap2/board-apollon.c +0 ~~-53~~

79 lines not on this page · raw message

Tony Lindgren

author maintainer

2007-04-16 22:16 UTC #8 lore raw

Re: [PATCH 5/7] ARM: OMAP: Merge board specific files from N800 tree

In reply to Tony Lindgren

Quoted 8 lines · Tony Lindgren

From: Kai Svahn <[email protected]>
This patch merges board specific files from N800 tree. Nokia has published the files at:
http://repository.maemo.org/pool/maemo3.0/free/source/
kernel-source-rx-34_2.6.18.orig.tar.gz
kernel-source-rx-34_2.6.18-osso29.diff.gz

Here's an updated version that fixes compile after my last fix to move externs to board-nokia.h.

Regards,

Tony

Quoted 1 line

From fd345ea126336a514baf808170f1231999ba2c1d Mon Sep 17 00:00:00 2001

From: Kai Svahn <[email protected]>
Date: Fri, 26 Jan 2007 12:39:48 -0800
Subject: [PATCH 5/7] ARM: OMAP: Merge board specific files from N800 tree

This patch merges board specific files from N800 tree. Nokia has published the files at:

http://repository.maemo.org/pool/maemo3.0/free/source/
kernel-source-rx-34_2.6.18.orig.tar.gz
kernel-source-rx-34_2.6.18-osso29.diff.gz

Signed-off-by Kai Svahn <[email protected]>

Signed-off-by Tony Lindgren <[email protected]>

arch/arm/mach-omap2/Kconfig +10 -1

Index: linux-2.6/arch/arm/mach-omap2/Kconfig
===================================================================
@@ -54,4 +54,13 @@ config MACH_OMAP_APOLLON
 
 config MACH_OMAP_2430SDP
 	bool "OMAP 2430 SDP board"
-	depends on ARCH_OMAP2 && ARCH_OMAP24XX
\ No newline at end of file
+	depends on ARCH_OMAP2 && ARCH_OMAP24XX
+
+config MACH_NOKIA_N800
+	bool "Nokia N800"
+	depends on ARCH_OMAP24XX
+
+config MACH_OMAP2_TUSB6010
+       bool
+       depends on ARCH_OMAP2 && ARCH_OMAP2420
+       default y if MACH_NOKIA_N800
\ No newline at end of file

arch/arm/mach-omap2/Makefile +4 -0

Index: linux-2.6/arch/arm/mach-omap2/Makefile
===================================================================
@@ -16,4 +16,8 @@ obj-$(CONFIG_MACH_OMAP_GENERIC)		+= boar
 obj-$(CONFIG_MACH_OMAP_H4)		+= board-h4.o
 obj-$(CONFIG_MACH_OMAP_2430SDP)		+= board-2430sdp.o
 obj-$(CONFIG_MACH_OMAP_APOLLON)		+= board-apollon.o
+obj-$(CONFIG_MACH_NOKIA_N800)		+= board-n800.o board-n800-flash.o \
+					   board-n800-mmc.o board-n800-bt.o \
+					   board-n800-audio.o board-n800-usb.o \
+					   board-n800-dsp.o board-n800-pm.o

arch/arm/mach-omap2/board-n800-audio.c new file +366 -0

366 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-bt.c new file +42 -0

42 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-dsp.c new file +156 -0

156 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-flash.c new file +156 -0

156 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-mmc.c new file +282 -0

282 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-pm.c new file +79 -0

79 lines not on this page · raw message

arch/arm/mach-omap2/board-n800-usb.c new file +102 -0

102 lines not on this page · raw message

arch/arm/mach-omap2/board-n800.c new file +515 -0

515 lines not on this page · raw message

include/asm-arm/arch-omap/board.h +22 -2

Index: linux-2.6/include/asm-arm/arch-omap/board.h
===================================================================
@@ -25,9 +25,12 @@
 #define OMAP_TAG_FBMEM		0x4f08
 #define OMAP_TAG_STI_CONSOLE	0x4f09
 #define OMAP_TAG_CAMERA_SENSOR	0x4f0a
+#define OMAP_TAG_PARTITION      0x4f0b
+#define OMAP_TAG_TEA5761	0x4f10
+#define OMAP_TAG_TMP105		0x4f11
 
 #define OMAP_TAG_BOOT_REASON    0x4f80
-#define OMAP_TAG_FLASH_PART	0x4f81
+#define OMAP_TAG_FLASH_PART_STR	0x4f81
 #define OMAP_TAG_VERSION_STR	0x4f82
 
 struct omap_clock_config {

@@ -139,8 +142,25 @@ struct omap_uart_config {
 	unsigned int enabled_uarts;
 };
 
+struct omap_tea5761_config {
+	u16 enable_gpio;
+};
+
+/* This cannot be passed from the bootloader */
+struct omap_tmp105_config {
+	u16 tmp105_irq_pin;
+	int (* set_power)(int enable);
+};
+
+struct omap_partition_config {
+	char name[16];
+	unsigned int size;
+	unsigned int offset;
+	/* same as in include/linux/mtd/partitions.h */
+	unsigned int mask_flags;
+};
 
-struct omap_flash_part_config {
+struct omap_flash_part_str_config {
 	char part_table[0];
 };

include/asm-arm/arch-omap/board-nokia.h +13 -1

Index: linux-2.6/include/asm-arm/arch-omap/board-nokia.h
===================================================================
@@ -11,12 +11,24 @@
 
 #include <linux/types.h>
 
+struct tsc2301_platform_data;
+struct dsp_kfunc_device;
+extern void n800_bt_init(void);
+extern void n800_dsp_init(void);
+extern void n800_flash_init(void);
+extern void n800_mmc_init(void);
+extern void n800_pm_init(void);
+extern void n800_usb_init(void);
+extern void n800_audio_init(struct tsc2301_platform_data *);
+extern int n800_audio_enable(struct dsp_kfunc_device *kdev, int stage);
+extern int n800_audio_disable(struct dsp_kfunc_device *kdev, int stage);
+extern void n800_mmc_slot1_cover_handler(void *arg, int state);
+
 #define OMAP_TAG_NOKIA_BT	0x4e01
 #define OMAP_TAG_WLAN_CX3110X	0x4e02
 #define OMAP_TAG_CBUS		0x4e03
 #define OMAP_TAG_EM_ASIC_BB5	0x4e04
 
-
 #define BT_CHIP_CSR		1
 #define BT_CHIP_TI		2

include/asm-arm/arch-omap/onenand.h +1 -0

Index: linux-2.6/include/asm-arm/arch-omap/onenand.h
===================================================================
@@ -16,4 +16,5 @@ struct omap_onenand_platform_data {
 	int			gpio_irq;
 	struct mtd_partition	*parts;
 	int			nr_parts;
+	int                     (*onenand_setup)(void __iomem *);
 };