Skip to contentSkip to conversation

Use common cpu_is_xxx() macros on AT91 and AVR32

PATCH In review Haavard Skinnemoen 2 participants 3 messages May 7, 2007

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/2 Use common cpu_is_xxx() macros on AT91 and AVR32

Several drivers shared between AT91 and AVR32 chips use cpu_is_xxx() to handle CPU-specific differences. Currently, such code needs to be inside #ifdef CONFIG_ARCH_AT91 because the macros don't exist on AVR32.

By defining the same macros on both AT91 and AVR32, these #ifdefs can be eliminated. Since the macros will evaluate to a constant value for CPUs that aren't supported by the current architecture, any code that is only needed on AT91 will be optimized away on AVR32 and vice versa.

---
 include/asm-arm/arch-at91/cpu.h     |    6 ++++++
 include/asm-avr32/arch-at32ap/cpu.h |   33 +++++++++++++++++++++++++++++++++
 2 files changed, 39 insertions(+), 0 deletions(-)
include/asm-arm/arch-at91/cpu.h +6 -0
index d464ca5..7ef4eeb 100644
@@ -68,4 +68,10 @@ static inline unsigned long at91_arch_identify(void)
 #define cpu_is_at91sam9263()	(0)
 #endif
 
+/*
+ * Since this is ARM, we will never run on any AVR32 CPU. But these
+ * definitions may reduce clutter in common drivers.
+ */
+#define cpu_is_at32ap7000()	(0)
+
 #endif
include/asm-avr32/arch-at32ap/cpu.h new file +33 -0
new file mode 100644
index 0000000..2bdc5bd
@@ -0,0 +1,33 @@
+/*
+ * AVR32 and (fake) AT91 CPU identification
+ *
+ * Copyright (C) 2007 Atmel Corporation
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __ASM_ARCH_CPU_H
+#define __ASM_ARCH_CPU_H
+
+/*
+ * Only AT32AP7000 is defined for now. We can identify the specific
+ * chip at runtime, but I'm not sure if it's really worth it.
+ */
+#ifdef CONFIG_CPU_AT32AP7000
+# define cpu_is_at32ap7000()	(1)
+#else
+# define cpu_is_at32ap7000()	(0)
+#endif
+
+/*
+ * Since this is AVR32, we will never run on any AT91 CPU. But these
+ * definitions may reduce clutter in common drivers.
+ */
+#define cpu_is_at91rm9200()	(0)
+#define cpu_is_at91sam9xe()	(0)
+#define cpu_is_at91sam9260()	(0)
+#define cpu_is_at91sam9261()	(0)
+#define cpu_is_at91sam9263()	(0)
+
+#endif /* __ASM_ARCH_CPU_H */
Signature · 1 line
1.4.4.4
#1 lore raw

PATCH 2/2 atmel_spi: Remove unnecessary (and wrong) #ifdefs

Now that the cpu_is_xxx() macros are available both on AVR32 and AT91, we can remove a couple of #ifdefs from this driver. One of them is actually wrong -- new_1 should be set on AVR32 but isn't. This causes the bus clock to run at twice the speed it is configured to.

---
 drivers/spi/atmel_spi.c |    5 -----
 1 files changed, 0 insertions(+), 5 deletions(-)
drivers/spi/atmel_spi.c +0 -5
index 66e7bc9..1d8a2f6 100644
@@ -22,10 +22,7 @@
 #include <asm/io.h>
 #include <asm/arch/board.h>
 #include <asm/arch/gpio.h>
-
-#ifdef CONFIG_ARCH_AT91
 #include <asm/arch/cpu.h>
-#endif
 
 #include "atmel_spi.h"
 
@@ -552,10 +549,8 @@ static int __init atmel_spi_probe(struct platform_device *pdev)
 		goto out_free_buffer;
 	as->irq = irq;
 	as->clk = clk;
-#ifdef CONFIG_ARCH_AT91
 	if (!cpu_is_at91rm9200())
 		as->new_1 = 1;
-#endif
 
 	ret = request_irq(irq, atmel_spi_interrupt, 0,
 			pdev->dev.bus_id, master);
Signature · 1 line
1.4.4.4
Acked-by on v1 1/2
#2 lore raw
In reply to Haavard Skinnemoen
Quoted 11 lines

Several drivers shared between AT91 and AVR32 chips use cpu_is_xxx() to handle CPU-specific differences. Currently, such code needs to be inside #ifdef CONFIG_ARCH_AT91 because the macros don't exist on AVR32.

By defining the same macros on both AT91 and AVR32, these #ifdefs can be eliminated. Since the macros will evaluate to a constant value for CPUs that aren't supported by the current architecture, any code that is only needed on AT91 will be optimized away on AVR32 and vice versa.