i386/x86_64 boot: document for 32 bit boot protocol

Index: linux-2.6.23-rc6/Documentation/i386/boot.txt
===================================================================
@@ -2,7 +2,7 @@
 		     ----------------------------
 
 		    H. Peter Anvin <[email protected]>
-			Last update 2007-05-23
+			Last update 2007-09-18
 
 On the i386 platform, the Linux kernel uses a rather complicated boot
 convention.  This has evolved partially due to historical aspects, as

@@ -42,6 +42,9 @@
 Protocol 2.06:	(Kernel 2.6.22) Added a field that contains the size of
 		the boot command line
 
+Protocol 2.07:	(kernel 2.6.23) Added a field of 64-bit physical
+		pointer to single linked list of struct	setup_data.
+		Added 32-bit boot protocol.
 
 **** MEMORY LAYOUT
 

@@ -168,6 +171,9 @@
 0234/1	2.05+	relocatable_kernel Whether kernel is relocatable or not
 0235/3	N/A	pad2		Unused
 0238/4	2.06+	cmdline_size	Maximum size of the kernel command line
+023c/4	N/A	pad3		Unused
+0240/8	2.07+	setup_data	64-bit physical pointer to linked list
+				of struct setup_data
 
 (1) For backwards compatibility, if the setup_sects field contains 0, the
     real value is 4.

@@ -480,6 +486,36 @@
   cmdline_size characters. With protocol version 2.05 and earlier, the
   maximum size was 255.
 
+Field name:	setup_data
+Type:		write (obligatory)
+Offset/size:	0x240/8
+Protocol:	2.07+
+
+  The 64-bit physical pointer to NULL terminated single linked list of
+  struct setup_data. This is used to define a more extensible boot
+  parameters passing mechanism. The definition of struct setup_data is
+  as follow:
+
+  struct setup_data {
+	  u64 next;
+	  u32 type;
+	  u32 len;
+	  u8  data[0];
+  } __attribute__((packed));
+
+  Where, the next is a 64-bit physical pointer to the next node of
+  linked list, the next field of the last node is 0; the type is used
+  to identify the contents of data; the len is the length of data
+  field; the data holds the real payload.
+
+  With this field, to add a new boot parameter written by bootloader,
+  it is not needed to add a new field to real mode header, just add a
+  new setup_data type is sufficient. But to add a new boot parameter
+  read by bootloader, it is still needed to add a new field.
+
+  TODO: Where is the safe place to place the linked list of struct
+  	setup_data?
+
 
 **** THE KERNEL COMMAND LINE
 

@@ -753,3 +789,35 @@
 	After completing your hook, you should jump to the address
 	that was in this field before your boot loader overwrote it
 	(relocated, if appropriate.)
+
+
+**** SETUP DATA TYPES
+
+
+**** 32-bit BOOT PROTOCOL
+
+For machine with some new BIOS other than legacy BIOS, such as EFI,
+LinuxBIOS, etc, and kexec, the 16-bit real mode setup code in kernel
+based on legacy BIOS can not be used, so a 32-bit boot protocol need
+to be defined.
+
+In 32-bit boot protocol, the first step in loading a Linux kernel
+should still be to load the real-mode code and then examine the kernel
+header at offset 0x01f1. But, it is not necessary to load all
+real-mode code, just first 4K bytes traditionally known as "zero page"
+is needed.
+
+In addition to read/modify/write kernel header of the zero page as
+that of 16-bit boot protocol, the boot loader should also fill the
+additional fields of the zero page as that described in zero-page.txt.
+
+After loading and setuping the zero page, the boot loader can load the
+32/64-bit kernel in the same way as that of 16-bit boot protocol.
+
+In 32-bit boot protocol, the kernel is started by jumping to the
+32-bit kernel entry point, which is the start address of loaded
+32/64-bit kernel.
+
+At entry, the CPU must be in 32-bit protected mode with paging
+disabled; the CS and DS must be 4G flat segments; %esi holds the base
+address of the "zero page"; %esp, %ebp, %edi should be zero.

129 lines not on this page · raw message