Skip to contentSkip to conversation

w1-gpio: Add GPIO w1 bus master driver (v2)

PATCH In review Ville Syrjala 2 participants 2 messages Dec 21, 2007

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/1 w1-gpio: Add GPIO w1 bus master driver (v2)

Add a GPIO 1-wire bus master driver. The driver used the GPIO API to control the wire and the GPIO pin can be specified using platform data similar to i2c-gpio. The driver was tested with AT91SAM9260 + DS2401.

---
Version 2 of the patch changes the sizeof to use the type as requested. I also had a better look at i2c-gpio and noticed that I should probably call gpio_request()/gpio_free(). Those functions are no-ops on mach-at91 but perhaps some other platforms require them. Also I removed the open-drain requirement like i2c-gpio does by toggling the pin direction.

 Documentation/w1/masters/00-INDEX |    2 +
 Documentation/w1/masters/w1-gpio  |   33 ++++++++++
 drivers/w1/masters/Kconfig        |   10 +++
 drivers/w1/masters/Makefile       |    1 +
 drivers/w1/masters/w1-gpio.c      |  125 +++++++++++++++++++++++++++++++++++++
 include/linux/w1-gpio.h           |   23 +++++++
 6 files changed, 194 insertions(+), 0 deletions(-)
 create mode 100644 Documentation/w1/masters/w1-gpio
 create mode 100644 drivers/w1/masters/w1-gpio.c
 create mode 100644 include/linux/w1-gpio.h
Documentation/w1/masters/00-INDEX +2 -0
index 752613c..7b0ceaa 100644
@@ -4,3 +4,5 @@ ds2482
 	- The Maxim/Dallas Semiconductor DS2482 provides 1-wire busses.
 ds2490
 	- The Maxim/Dallas Semiconductor DS2490 builds USB <-> W1 bridges.
+w1-gpio
+	- GPIO 1-wire bus master driver.
Documentation/w1/masters/w1-gpio new file +33 -0
new file mode 100644
index 0000000..af5d3b4
@@ -0,0 +1,33 @@
+Kernel driver w1-gpio
+=====================
+
+Author: Ville Syrjala <[email protected]>
+
+
+Description
+-----------
+
+GPIO 1-wire bus master driver. The driver uses the GPIO API to control the
+wire and the GPIO pin can be specified using platform data.
+
+
+Example (mach-at91)
+-------------------
+
+#include <linux/w1-gpio.h>
+
+static struct w1_gpio_platform_data foo_w1_gpio_pdata = {
+	.pin		= AT91_PIN_PB20,
+	.is_open_drain	= 1,
+};
+
+static struct platform_device foo_w1_device = {
+	.name			= "w1-gpio",
+	.id			= -1,
+	.dev.platform_data	= &foo_w1_gpio_pdata,
+};
+
+...
+	at91_set_GPIO_periph(foo_w1_gpio_pdata.pin, 1);
+	at91_set_multi_drive(foo_w1_gpio_pdata.pin, 1);
+	platform_device_register(&foo_w1_device);
drivers/w1/masters/Kconfig +10 -0
index 8236d44..c449309 100644
@@ -42,5 +42,15 @@ config W1_MASTER_DS1WM
 	  in HP iPAQ devices like h5xxx, h2200, and ASIC3-based like
 	  hx4700.
 
+config W1_MASTER_GPIO
+	tristate "GPIO 1-wire busmaster"
+	depends on GENERIC_GPIO
+	help
+	  Say Y here if you want to communicate with your 1-wire devices using
+	  GPIO pins. This driver uses the GPIO API to control the wire.
+
+	  This support is also available as a module.  If so, the module
+	  will be called w1-gpio.ko.
+
 endmenu
 
drivers/w1/masters/Makefile +1 -0
index 11551b3..1420b5b 100644
@@ -6,3 +6,4 @@ obj-$(CONFIG_W1_MASTER_MATROX)		+= matrox_w1.o
 obj-$(CONFIG_W1_MASTER_DS2490)		+= ds2490.o
 obj-$(CONFIG_W1_MASTER_DS2482)		+= ds2482.o
 obj-$(CONFIG_W1_MASTER_DS1WM)		+= ds1wm.o
+obj-$(CONFIG_W1_MASTER_GPIO)		+= w1-gpio.o
drivers/w1/masters/w1-gpio.c new file +125 -0

125 lines not on this page · raw message

include/linux/w1-gpio.h new file +23 -0
new file mode 100644
index 0000000..9797fec
@@ -0,0 +1,23 @@
+/*
+ * w1-gpio interface to platform code
+ *
+ * Copyright (C) 2007 Ville Syrjala <[email protected]>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2
+ * as published by the Free Software Foundation.
+ */
+#ifndef _LINUX_W1_GPIO_H
+#define _LINUX_W1_GPIO_H
+
+/**
+ * struct w1_gpio_platform_data - Platform-dependent data for w1-gpio
+ * @pin: GPIO pin to use
+ * @is_open_drain: GPIO pin is configured as open drain
+ */
+struct w1_gpio_platform_data {
+	unsigned int pin;
+	unsigned int is_open_drain:1;
+};
+
+#endif /* _LINUX_W1_GPIO_H */
Signature · 1 line
1.5.2.5
#1 lore raw
Quoted 5 lines · Ville Syrjala

Add a GPIO 1-wire bus master driver. The driver used the GPIO API to control the wire and the GPIO pin can be specified using platform data similar to i2c-gpio. The driver was tested with AT91SAM9260 + DS2401.

This looks ok, thank you!
Feel free to add my ack or signed-off.

Andrew, please apply.

Signature · 1 line
	Evgeniy Polyakov