VXWorks EST Flat Binary
HI Folks,
How I can load (and start) an EST Flat Bin image? My supplier gives me this image and I don't know how run it from u-boot (from git). Can someone help me?
thanks a lot.
luigi
Signature · 9 lines
______ Luigi Mantellini
.'______'. R&D - Software
(.' '.) Industrie Dial Face S.p.A.
( :=----=: ) Via Canzo, 4
('.______.') 20068 Peschiera Borromeo (MI), Italy
'.______.' Tel.: +39 02 5167 2813
Fax: +39 02 5167 2459
Ind. Dial Face Email: luigi.mantellini at idf-hit.com
www.idf-hit.comQuoted 3 lines · Luigi 'Comio' Mantellini
How I can load (and start) an EST Flat Bin image? My supplier gives me this image and I don't know how run it from u-boot (from git). Can someone help me?
The EST flat binary is a pure binary file with a 32-byte header. You can easily strip the header using 'dd' and then load using tftp. You just need to know where to load the binary and what the entry point is (the default load address is included in the header).
I am surprised that you get the file in this format, it is intended for programming a binary into flash using the old visionCLICK software.
Rich
Hi Richard,
Thanks for your answer.
Quoted 10 lines · Richard Danter
Quoted 3 lines · Luigi 'Comio' Mantellini
How I can load (and start) an EST Flat Bin image? My supplier gives me this image and I don't know how run it from u-boot (from git). Can someone help me?
The EST flat binary is a pure binary file with a 32-byte header. You can easily strip the header using 'dd' and then load using tftp. You just need to know where to load the binary and what the entry point is (the default load address is included in the header).
Ok. In fact, using an ex editor I noticed a simil-vectors table. Do you know where I can obtain the format specification?
Quoted 3 lines
I am surprised that you get the file in this format, it is intended for programming a binary into flash using the old visionCLICK software.
I too! I'll ask to my supplier to give me a more recent version of this image.
Thanks again once.
luigi
Quoted 2 lines
Rich
Industrie Dial Face S.p.A.
Luigi Mantellini
R&D - Software
Industrie Dial Face S.p.A.
Via Canzo, 4
20068 Peschiera Borromeo (MI), Italy
Tel.: +39 02 5167 2813
Fax: +39 02 5167 2459
E-mail: luigi.mantellini at idf-hit.com
GPG fingerprint: 3DD1 7B71 FBDF 6376
1B4A
B003 175F E979 907E1650
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20080307/e0fd068e/attachment.htm
-------------- next part --------------
A non-text attachment was scrubbed...
Name: idf_logo.gif
Type: image/gif
Size: 4122 bytes
Desc: not available
Url : http://lists.denx.de/pipermail/u-boot/attachments/20080307/e0fd068e/attachment.gif
Quoted 11 lines · Luigi 'Comio' Mantellini
Hi Richard,
Thanks for your answer.
On ven, 2008-03-07 at 14:58 +0000, Richard Danter wrote:
Quoted 3 lines · Luigi 'Comio' Mantellini
How I can load (and start) an EST Flat Bin image? My supplier gives me this image and I don't know how run it from u-boot (from git). Can someone help me?
Quoted 8 lines
The EST flat binary is a pure binary file with a 32-byte header. You can easily strip the header using 'dd' and then load using tftp. You just need to know where to load the binary and what the entry point is (the default load address is included in the header).
Ok. In fact, using an ex editor I noticed a simil-vectors table. Do you know where I can obtain the format specification?
There is an application note available from Wind River.
Rich
Quoted 28 lines
I am surprised that you get the file in this format, it is intended
for programming a binary into flash using the old visionCLICK software.I too! I'll ask to my supplier to give me a more recent version of this image.
Thanks again once.
luigi
Rich
Luigi Mantellini
R&D - Software
Industrie Dial Face S.p.A.
Via Canzo, 4
20068 Peschiera Borromeo (MI), Italy
Tel.: +39 02 5167 2813
Fax: +39 02 5167 2459
E-mail: luigi.mantellini at idf-hit.com
GPG fingerprint: 3DD1 7B71 FBDF 6376 1B4AB003 175F E979 907E 1650