USB disconnects every 30 seconds (2.6.27-rc8)
Subsystems (2)
I'm seeing some odd USB behavior with newer kernels (2.6.27-rc8-00062-g330f647 to be exact). Almost exactly, every 30 seconds, one of my USB hubs disconnects. At first, I thought it was a hardware issue, and started swapping cables. Then, I realized that I'd *just* rebooted into a new kernel. So, I booted back to the distro kernel and these went away.
Even though my mouse is hanging off that hub, I don't seem to notice the disconnects.
$ dmesg | grep disconnect [ 3599.496217] usb 3-4.4.4: USB disconnect, address 122 [ 3599.677346] usb 3-4.1: USB disconnect, address 121 [ 3627.804621] usb 3-4.1: USB disconnect, address 124 [ 3628.004400] usb 3-4.4.4: USB disconnect, address 123 [ 3659.496421] usb 3-4.4.4: USB disconnect, address 126 [ 3659.676186] usb 3-4.1: USB disconnect, address 125 [ 3689.493763] usb 3-4.1: USB disconnect, address 3 [ 3689.708916] usb 3-4.4.4: USB disconnect, address 127 [ 3719.497221] usb 3-4.4.4: USB disconnect, address 7 [ 3719.684965] usb 3-4.1: USB disconnect, address 6 [ 3749.496323] usb 3-4.1: USB disconnect, address 9 [ 3749.691180] usb 3-4.4.4: USB disconnect, address 8
Full dmesg and .config:
http://sr71.net/~dave/linux/config-10-03-2008.1.txt
http://sr71.net/~dave/linux/dmesg-10-03-2008.1.log
The last one I tried before this was -rc3, and it appears to be OK. The Ubuntu 2.6.24-19-generic kernel also appears not to have this issue.
A quick scan of LKML and linux-usb didn't turn up anything similar.
The machine is a Lenovo T61 plugged into the Lenovo dock. At this point, the only thing plugged into the suspect hub is my mouse.
-- Dave
Quoted 3 lines · Dave Hansen
I'm seeing some odd USB behavior with newer kernels (2.6.27-rc8-00062-g330f647 to be exact). Almost exactly, every 30 seconds, one of my USB hubs disconnects.
Actually two of the hubs disconnect: 3-4.1 and 3-4.4.4. Neither is beneath the other.
Quoted 6 lines
At first, I thought it was a
hardware issue, and started swapping cables. Then, I realized that I'd *just* rebooted into a new kernel. So, I booted back to the distro kernel and these went away.Even though my mouse is hanging off that hub,
No it isn't. The mouse is 3-4.4.1, which is not below either 3-4.1 or 3-4.4.4.
Quoted 22 lines
I don't seem to notice the
disconnects.$ dmesg | grep disconnect [ 3599.496217] usb 3-4.4.4: USB disconnect, address 122 [ 3599.677346] usb 3-4.1: USB disconnect, address 121 [ 3627.804621] usb 3-4.1: USB disconnect, address 124 [ 3628.004400] usb 3-4.4.4: USB disconnect, address 123 [ 3659.496421] usb 3-4.4.4: USB disconnect, address 126 [ 3659.676186] usb 3-4.1: USB disconnect, address 125 [ 3689.493763] usb 3-4.1: USB disconnect, address 3 [ 3689.708916] usb 3-4.4.4: USB disconnect, address 127 [ 3719.497221] usb 3-4.4.4: USB disconnect, address 7 [ 3719.684965] usb 3-4.1: USB disconnect, address 6 [ 3749.496323] usb 3-4.1: USB disconnect, address 9 [ 3749.691180] usb 3-4.4.4: USB disconnect, address 8Full dmesg and .config:
http://sr71.net/~dave/linux/config-10-03-2008.1.txt
http://sr71.net/~dave/linux/dmesg-10-03-2008.1.log
Quoted 7 lines
The last one I tried before this was -rc3, and it appears to be OK. The Ubuntu 2.6.24-19-generic kernel also appears not to have this issue.
A quick scan of LKML and linux-usb didn't turn up anything similar.
The machine is a Lenovo T61 plugged into the Lenovo dock. At this point, the only thing plugged into the suspect hub is my mouse.
In fact, nothing is plugged into either of the hubs.
In theory this could be caused by a problem in the dock. But it would be better to get more information before trying to pin down the cause.
You should use usbmon (see Documentation/usb/usbmon.txt) to record a trace of everything happening on bus 3. And to keep things simple, you should unplug all the USB devices except for one of the magical disappearing hubs.
Alan Stern
Quoted 7 lines · Alan Stern
Quoted 3 lines · Dave Hansen
I'm seeing some odd USB behavior with newer kernels (2.6.27-rc8-00062-g330f647 to be exact). Almost exactly, every 30 seconds, one of my USB hubs disconnects.
Actually two of the hubs disconnect: 3-4.1 and 3-4.4.4. Neither is beneath the other.
Yeah, it's a "7-port hub". I assume that means that it's a pair of 4-porters plugged together somehow.
It is this exact model:
http://store.pchcables.com/usb7posepohu.html
Quoted 9 lines
Quoted 6 lines
At first, I thought it was a
hardware issue, and started swapping cables. Then, I realized that I'd *just* rebooted into a new kernel. So, I booted back to the distro kernel and these went away.Even though my mouse is hanging off that hub,
No it isn't. The mouse is 3-4.4.1, which is not below either 3-4.1 or 3-4.4.4.
Huh, that's odd.
The T61 has two (empty) USB ports on the left, one on the right, and 4 on the dock. The configuration I've had so far is the 7-port hub plugged into one of the four ports on the back of the T61.
Quoted 5 lines
Quoted 2 lines
The machine is a Lenovo T61 plugged into the Lenovo dock. At this point, the only thing plugged into the suspect hub is my mouse.
In fact, nothing is plugged into either of the hubs.
Quoted 7 lines
In theory this could be caused by a problem in the dock. But it would be better to get more information before trying to pin down the cause.
You should use usbmon (see
Documentation/usb/usbmon.txt) to record a trace of everything happening on bus 3. And to keep things simple, you should unplug all the USB devices except for one of the magical disappearing hubs.
Unfortunately, the disconnects don't happen unless both my 7-port hub and the mouse are connected. So, I've disconnected everything but those two things. I also plugged the mouse into the single port on the right side of the T61 instead of the dock.
usbmon output: http://sr71.net/~dave/linux/1.mon.out
I've also attached appended the corresponding dmesg with annotations of what I did when.
plug in mouse:
Oct 3 11:53:51 nimitz kernel: [ 8253.306987] usb 2-1: new low speed USB device using uhci_hcd and address 4 Oct 3 11:53:51 nimitz kernel: [ 8253.420284] usb 2-1: configuration #1 chosen from 1 choice Oct 3 11:53:52 nimitz kernel: [ 8253.476663] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1a.1/usb2/2-1/2-1:1.0/input/input13 Oct 3 11:53:52 nimitz kernel: [ 8253.493970] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1a.1-1 plug in '7 port' hub: Oct 3 11:54:26 nimitz kernel: [ 8288.132987] usb 3-4.3: new high speed USB device using ehci_hcd and address 47 Oct 3 11:54:26 nimitz kernel: [ 8288.188960] usb 3-4.3: configuration #1 chosen from 1 choice Oct 3 11:54:26 nimitz kernel: [ 8288.189371] hub 3-4.3:1.0: USB hub found Oct 3 11:54:26 nimitz kernel: [ 8288.189669] hub 3-4.3:1.0: 4 ports detected Oct 3 11:54:26 nimitz kernel: [ 8288.339300] usb 3-4.3.4: new high speed USB device using ehci_hcd and address 48 Oct 3 11:54:26 nimitz kernel: [ 8288.395323] usb 3-4.3.4: configuration #1 chosen from 1 choice Oct 3 11:54:26 nimitz kernel: [ 8288.395611] hub 3-4.3.4:1.0: USB hub found Oct 3 11:54:26 nimitz kernel: [ 8288.395928] hub 3-4.3.4:1.0: 4 ports detected 'hub disconnects:' (I didn't do anything physically here) Oct 3 11:54:52 nimitz kernel: [ 8313.567487] usb 3-4.3: USB disconnect, address 47 Oct 3 11:54:52 nimitz kernel: [ 8313.567492] usb 3-4.3.4: USB disconnect, address 48 Oct 3 11:54:52 nimitz kernel: [ 8313.619115] usb 3-4.3: new high speed USB device using ehci_hcd and address 49 Oct 3 11:54:52 nimitz kernel: [ 8313.675618] usb 3-4.3: configuration #1 chosen from 1 choice Oct 3 11:54:52 nimitz kernel: [ 8313.675887] hub 3-4.3:1.0: USB hub found Oct 3 11:54:52 nimitz kernel: [ 8313.676232] hub 3-4.3:1.0: 4 ports detected Oct 3 11:54:52 nimitz kernel: [ 8313.823367] usb 3-4.3.4: new high speed USB device using ehci_hcd and address 50 Oct 3 11:54:52 nimitz kernel: [ 8313.880913] usb 3-4.3.4: configuration #1 chosen from 1 choice Oct 3 11:54:52 nimitz kernel: [ 8313.881140] hub 3-4.3.4:1.0: USB hub found Oct 3 11:54:52 nimitz kernel: [ 8313.881485] hub 3-4.3.4:1.0: 4 ports detected Oct 3 11:55:22 nimitz kernel: [ 8343.572344] usb 3-4.3: USB disconnect, address 49 Oct 3 11:55:22 nimitz kernel: [ 8343.572355] usb 3-4.3.4: USB disconnect, address 50 Oct 3 11:55:22 nimitz kernel: [ 8343.695579] usb 3-4.3: new high speed USB device using ehci_hcd and address 51 Oct 3 11:55:22 nimitz kernel: [ 8343.754283] usb 3-4.3: configuration #1 chosen from 1 choice Oct 3 11:55:22 nimitz kernel: [ 8343.754598] hub 3-4.3:1.0: USB hub found Oct 3 11:55:22 nimitz kernel: [ 8343.754923] hub 3-4.3:1.0: 4 ports detected Oct 3 11:55:22 nimitz kernel: [ 8343.908841] usb 3-4.3.4: new high speed USB device using ehci_hcd and address 52 Oct 3 11:55:22 nimitz kernel: [ 8343.964966] usb 3-4.3.4: configuration #1 chosen from 1 choice Oct 3 11:55:22 nimitz kernel: [ 8343.965247] hub 3-4.3.4:1.0: USB hub found
-- Dave
Quoted 2 lines · Dave Hansen
Yeah, it's a "7-port hub". I assume that means that it's a pair of 4-porters plugged together somehow.
It turns out that's exactly right.
Quoted 6 lines
Unfortunately, the disconnects don't happen unless both my 7-port hub and the mouse are connected. So, I've disconnected everything but those two things. I also plugged the mouse into the single port on the right side of the T61 instead of the dock.
usbmon output: http://sr71.net/~dave/linux/1.mon.out
The usbmon trace answers a few questions. And it raises one other.
Quoted 8 lines
I've also attached appended the corresponding dmesg with annotations of what I did when.
plug in mouse:
Oct 3 11:53:51 nimitz kernel: [ 8253.306987] usb 2-1: new low speed USB device using uhci_hcd and address 4 Oct 3 11:53:51 nimitz kernel: [ 8253.420284] usb 2-1: configuration #1 chosen from 1 choice Oct 3 11:53:52 nimitz kernel: [ 8253.476663] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1a.1/usb2/2-1/2-1:1.0/input/input13 Oct 3 11:53:52 nimitz kernel: [ 8253.493970] input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1a.1-1
That was more or less normal.
Quoted 9 lines
plug in '7 port' hub:
Oct 3 11:54:26 nimitz kernel: [ 8288.132987] usb 3-4.3: new high speed USB device using ehci_hcd and address 47 Oct 3 11:54:26 nimitz kernel: [ 8288.188960] usb 3-4.3: configuration #1 chosen from 1 choice Oct 3 11:54:26 nimitz kernel: [ 8288.189371] hub 3-4.3:1.0: USB hub found Oct 3 11:54:26 nimitz kernel: [ 8288.189669] hub 3-4.3:1.0: 4 ports detected Oct 3 11:54:26 nimitz kernel: [ 8288.339300] usb 3-4.3.4: new high speed USB device using ehci_hcd and address 48 Oct 3 11:54:26 nimitz kernel: [ 8288.395323] usb 3-4.3.4: configuration #1 chosen from 1 choice Oct 3 11:54:26 nimitz kernel: [ 8288.395611] hub 3-4.3.4:1.0: USB hub found Oct 3 11:54:26 nimitz kernel: [ 8288.395928] hub 3-4.3.4:1.0: 4 ports detected
As you can see, it is really two 4-port hubs: 3-4.3 and 3-4.3.4 (which is connected to port 4 of 4.3).
Quoted 3 lines
'hub disconnects:' (I didn't do anything physically here)
Oct 3 11:54:52 nimitz kernel: [ 8313.567487] usb 3-4.3: USB disconnect, address 47 Oct 3 11:54:52 nimitz kernel: [ 8313.567492] usb 3-4.3.4: USB disconnect, address 48
Okay. You didn't do anything, but _something_ did. Probably a program running on your computer that checks out all the usb devices every 30 seconds. The usbmon trace clearly shows every suspended hub (which is all but the one the mouse is plugged into) being woken up at 30-second intervals.
Suspiciously enough, at the same time a vendor-specific request is sent to the mouse. This, together with the fact that the disconnects occur only when the mouse is plugged in, strongly suggests that some program is trying to use the mouse and is doing something bad every 30 seconds.
Below is a patch you can apply; it may indicate which program is responsible. In order to use it you'll have to do:
echo 1 >/sys/module/usbcore/parameters/usbfs_snoop
before plugging in the mouse.
The next question is why the disconnects? This is harder to explain. It's evident in the trace that there's something wrong with the timing code in your computer. This shows up in several places, most clearly when the 7-port hub is resumed.
A resume works as follows: The computer sends a Clear-Port-Suspend request to the hub's parent and then waits at least 25 milliseconds for the suspend to end. In your trace, that delay lasts only 16 ms, which wasn't long enough. The suspend was still in progress, so the kernel decided something was wrong and disconnected the 7-port hub. You can see it here (the second field on each line is a timestamp in microseconds):
f6194900 1490306395 S Co:3:002:0 s 23 01 0002 0003 0000 0 f6194900 1490306515 C Co:3:002:0 0 0f6194900 1490322567 S Ci:3:002:0 s a3 00 0000 0003 0004 4 < f6194900 1490322614 C Ci:3:002:0 0 4 = 07050000 f6194900 1490330540 S Co:3:002:0 s 23 01 0001 0003 0000 0 f6194900 1490330614 C Co:3:002:0 0 0
The first two lines show the Clear-Port-Suspend request being sent and completing normally. The third and fourth lines show a Get-Port-Status request; the difference in times between the second and third lines is 1490322567 - 1490306515 = 16052 us, or about 16 ms. But the source code for that delay says:
msleep(25);
so something is badly wrong. And sure enough, the status value 07050000 indicates that the Suspend feature is still turned on. The last two lines show the hub being logically disconnected.
There are a number of other places in the trace where delays are shorter than they should be. This is out of my area of expertise, so I'm CC'ing Thomas Gleixner. With luck he'll be able to help.
Thomas, the background for this problem is available here:
http://marc.info/?l=linux-kernel&m=122305738430115&w=2
Alan Stern
drivers/usb/core/devio.c +2 -0
@@ -625,6 +625,8 @@ static int usbdev_open(struct inode *inosmp_wmb ();list_add_tail (&ps->list, &dev->filelist); file->private_data = ps; +snoop (&dev->dev,"opened by process %d: %s\n" ,task_pid_nr (current), + current->comm); out:if (ret) {kfree (ps);
Quoted 8 lines · Alan Stern
On Fri, 3 Oct 2008, Dave Hansen wrote:
There are a number of other places in the trace where delays are shorter than they should be. This is out of my area of expertise, so I'm CC'ing Thomas Gleixner. With luck he'll be able to help.Thomas, the background for this problem is available here:
http://marc.info/?l=linux-kernel&m=122305738430115&w=2
Is NOHZ and HIGHRES disabled on those kernels? Hugh spotted a typo in that code today. Fix is below. It causes jiffies to increment too fast which explains your short delays.
Thanks,
tglx
---
kernel/time/tick-broadcast.c +4 -2
@@ -235,7 +235,8 @@ static void tick_do_broadcast_on_off(void *why)case CLOCK_EVT_NOTIFY_BROADCAST_FORCE :if (!cpu_isset (cpu, tick_broadcast_mask)) {cpu_set (cpu, tick_broadcast_mask); -if (bc->mode ==TICKDEV_MODE_PERIODIC ) +if (tick_broadcast_device.mode == +TICKDEV_MODE_PERIODIC )clockevents_shutdown (dev); }if (*reason ==CLOCK_EVT_NOTIFY_BROADCAST_FORCE )
@@ -245,7 +246,8 @@ static void tick_do_broadcast_on_off(void *why)if (!tick_broadcast_force &&cpu_isset (cpu, tick_broadcast_mask)) {cpu_clear (cpu, tick_broadcast_mask); -if (bc->mode ==TICKDEV_MODE_PERIODIC ) +if (tick_broadcast_device.mode == +TICKDEV_MODE_PERIODIC )tick_setup_periodic (dev,0 ); }break ;
Quoted 6 lines · Thomas Gleixner
Quoted 5 lines · Alan Stern
On Fri, 3 Oct 2008, Dave Hansen wrote:
There are a number of other places in the trace where delays are shorter than they should be. This is out of my area of expertise, so I'm CC'ing Thomas Gleixner. With luck he'll be able to help.
Quoted 7 lines
Quoted 3 lines
Thomas, the background for this problem is available here:
http://marc.info/?l=linux-kernel&m=122305738430115&w=2Is NOHZ and HIGHRES disabled on those kernels? Hugh spotted a typo in that code today. Fix is below. It causes jiffies to increment too fast which explains your short delays.
Here's my config:
http://sr71.net/~dave/linux/config-10-03-2008.1.txt
No NOHZ or HIGHRES. Is that what you meant?
-- Dave
OK, here's output with both Thomas/Hugh's timing fix as well as the USB snooping turned on. The disconnects still happen, but I did get some good snoop output:
Oct 3 16:01:59 nimitz kernel: [ 180.273883] usb usb7: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.273894] usb usb7: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.273935] usb usb7: opened by process 6485: hald-addon-usb-
grepping for hald:
dave@nimitz:~$ ps aux | grep hald 111 6407 0.5 0.1 6340 4352 ? Ss 15:59 0:00 /usr/sbin/hald root 6411 0.0 0.0 3348 1152 ? S 15:59 0:00 hald-runner root 6485 0.1 0.0 2996 1140 ? S 15:59 0:00 hald-addon-usb-csr: listening on 'MX700 Optical Mouse' ...
If I kill off 'hald-addon-usb-csr', then the resets stop happening. Restart hal, and they come back.
Oct 3 16:01:59 nimitz kernel: [ 180.273883] usb usb7: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.273894] usb usb7: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.273935] usb usb7: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.273940] usb usb7: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.392126] usb 3-4: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.393185] usb 3-4.3: USB disconnect, address 16 Oct 3 16:01:59 nimitz kernel: [ 180.393191] usb 3-4.3.4: USB disconnect, address 17 Oct 3 16:01:59 nimitz kernel: [ 180.437913] usb 3-4.3: new high speed USB device using ehci_hcd and address 18 Oct 3 16:01:59 nimitz kernel: [ 180.494705] usb 3-4.3: configuration #1 chosen from 1 choice Oct 3 16:01:59 nimitz kernel: [ 180.495101] hub 3-4.3:1.0: USB hub found Oct 3 16:01:59 nimitz kernel: [ 180.495409] hub 3-4.3:1.0: 4 ports detected Oct 3 16:01:59 nimitz kernel: [ 180.600101] usb 3-4: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.600144] usb usb3: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.600147] usb usb3: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.600167] usb 3-4: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.600170] usb 3-4: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.600179] usb usb3: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.600182] usb usb3: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.619896] usb usb6: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.620387] usb usb6: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.620766] usb usb6: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.621179] usb usb6: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.640068] usb usb5: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.640509] usb usb5: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.640866] usb usb5: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.641278] usb usb5: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.641599] usb 4-1: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.642006] usb 4-1: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.642347] usb usb4: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.642757] usb usb4: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.643108] usb 4-1: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.643524] usb 4-1: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.643872] usb usb4: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.644159] usb 3-4.3.4: new high speed USB device using ehci_hcd and address 19 Oct 3 16:01:59 nimitz kernel: [ 180.644856] usb usb4: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.645180] usb 2-1: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.645612] usb 2-1: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.645954] usb usb2: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.646531] usb usb2: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.646888] usb 2-1: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.647314] usb 2-1: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.647640] usb usb2: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.648106] usb usb2: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.667895] usb usb1: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.668340] usb usb1: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.668689] usb usb1: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.669101] usb usb1: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.669420] usb 2-1: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.669823] usb 2-1: usbdev_ioctl: CONTROL Oct 3 16:01:59 nimitz kernel: [ 180.669827] usb 2-1: control read: bRequest=09 bRrequestType=c0 wValue=0003 wIndex=0000 wLength=0008 Oct 3 16:01:59 nimitz kernel: [ 180.673036] usb 2-1: control read: data 20 3d 8b 45 05 0b 01 ee Oct 3 16:01:59 nimitz kernel: [ 180.701219] usb 3-4.3.4: configuration #1 chosen from 1 choice Oct 3 16:01:59 nimitz kernel: [ 180.701552] hub 3-4.3.4:1.0: USB hub found Oct 3 16:01:59 nimitz kernel: [ 180.701905] hub 3-4.3.4:1.0: 4 ports detected
-- Dave
Hi Dave,
Quoted 8 lines
OK, here's output with both Thomas/Hugh's timing fix as well as the USB snooping turned on. The disconnects still happen, but I did get some good snoop output:
Oct 3 16:01:59 nimitz kernel: [ 180.273883] usb usb7: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.273894] usb usb7: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.273935] usb usb7: opened by process 6485: hald-addon-usb-
Quoted 8 lines
grepping for hald:
dave@nimitz:~$ ps aux | grep hald 111 6407 0.5 0.1 6340 4352 ? Ss 15:59 0:00 /usr/sbin/hald root 6411 0.0 0.0 3348 1152 ? S 15:59 0:00 hald-runner root 6485 0.1 0.0 2996 1140 ? S 15:59 0:00 hald-addon-usb-csr: listening on 'MX700 Optical Mouse' ...If I kill off 'hald-addon-usb-csr', then the resets stop happening.
the addon is for some weird handling of CSR based HID devices in their Bluetooth/USB HID proxy devices or so.
Alan, that is the vendor request you saw. Don't ask me what exactly this one does. I really have no idea.
Regards
Marcel
Quoted 7 lines · Marcel Holtmann
Hi Dave,
the addon is for some weird handling of CSR based HID devices in their Bluetooth/USB HID proxy devices or so.
Alan, that is the vendor request you saw. Don't ask me what exactly this one does. I really have no idea.
I wasn't going to. :-)
Alan Stern
Quoted 9 lines · Dave Hansen
OK, here's output with both Thomas/Hugh's timing fix as well as the USB snooping turned on. The disconnects still happen, but I did get some good snoop output:
Oct 3 16:01:59 nimitz kernel: [ 180.273883] usb usb7: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.273894] usb usb7: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.273935] usb usb7: opened by process 6485: hald-addon-usb-grepping for hald:
Quoted 8 lines
dave@nimitz:~$ ps aux | grep hald 111 6407 0.5 0.1 6340 4352 ? Ss 15:59 0:00 /usr/sbin/hald root 6411 0.0 0.0 3348 1152 ? S 15:59 0:00 hald-runner root 6485 0.1 0.0 2996 1140 ? S 15:59 0:00 hald-addon-usb-csr: listening on 'MX700 Optical Mouse' ...If I kill off 'hald-addon-usb-csr', then the resets stop happening. Restart hal, and they come back.
There's probably a setting for hal which will prevent this constant probing.
Quoted 8 lines
Oct 3 16:01:59 nimitz kernel: [ 180.273883] usb usb7: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.273894] usb usb7: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.273935] usb usb7: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.273940] usb usb7: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.392126] usb 3-4: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.393185] usb 3-4.3: USB disconnect, address 16 Oct 3 16:01:59 nimitz kernel: [ 180.393191] usb 3-4.3.4: USB disconnect, address 17 Oct 3 16:01:59 nimitz kernel: [ 180.437913] usb 3-4.3: new high speed USB device using ehci_hcd and address 18
Quoted 8 lines
Oct 3 16:01:59 nimitz kernel: [ 180.494705] usb 3-4.3: configuration #1 chosen from 1 choice Oct 3 16:01:59 nimitz kernel: [ 180.495101] hub 3-4.3:1.0: USB hub found Oct 3 16:01:59 nimitz kernel: [ 180.495409] hub 3-4.3:1.0: 4 ports detected Oct 3 16:01:59 nimitz kernel: [ 180.600101] usb 3-4: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.600144] usb usb3: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.600147] usb usb3: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.600167] usb 3-4: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.600170] usb 3-4: usbdev_ioctl: IOCTL
Without a usbmon log, I can't tell what may still be going wrong.
Alan Stern
Quoted 17 lines · Alan Stern
Quoted 8 lines
Oct 3 16:01:59 nimitz kernel: [ 180.273883] usb usb7: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.273894] usb usb7: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.273935] usb usb7: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.273940] usb usb7: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.392126] usb 3-4: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.393185] usb 3-4.3: USB disconnect, address 16 Oct 3 16:01:59 nimitz kernel: [ 180.393191] usb 3-4.3.4: USB disconnect, address 17 Oct 3 16:01:59 nimitz kernel: [ 180.437913] usb 3-4.3: new high speed USB device using ehci_hcd and address 18Quoted 8 lines
Oct 3 16:01:59 nimitz kernel: [ 180.494705] usb 3-4.3: configuration #1 chosen from 1 choice Oct 3 16:01:59 nimitz kernel: [ 180.495101] hub 3-4.3:1.0: USB hub found Oct 3 16:01:59 nimitz kernel: [ 180.495409] hub 3-4.3:1.0: 4 ports detected Oct 3 16:01:59 nimitz kernel: [ 180.600101] usb 3-4: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.600144] usb usb3: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.600147] usb usb3: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.600167] usb 3-4: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.600170] usb 3-4: usbdev_ioctl: IOCTL
Quoted 1 line
Without a usbmon log, I can't tell what may still be going wrong.
This log should have recorded what was going on there. Was there something else that I should be capturing with usbmon that I missed?
http://sr71.net/~dave/linux/1.mon.out
-- Dave
Quoted 18 lines · Dave Hansen
Quoted 17 lines · Alan Stern
Quoted 16 lines
Oct 3 16:01:59 nimitz kernel: [ 180.273883] usb usb7: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.273894] usb usb7: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.273935] usb usb7: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.273940] usb usb7: usbdev_ioctl: IOCTL Oct 3 16:01:59 nimitz kernel: [ 180.392126] usb 3-4: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.393185] usb 3-4.3: USB disconnect, address 16 Oct 3 16:01:59 nimitz kernel: [ 180.393191] usb 3-4.3.4: USB disconnect, address 17 Oct 3 16:01:59 nimitz kernel: [ 180.437913] usb 3-4.3: new high speed USB device using ehci_hcd and address 18 Oct 3 16:01:59 nimitz kernel: [ 180.494705] usb 3-4.3: configuration #1 chosen from 1 choice Oct 3 16:01:59 nimitz kernel: [ 180.495101] hub 3-4.3:1.0: USB hub found Oct 3 16:01:59 nimitz kernel: [ 180.495409] hub 3-4.3:1.0: 4 ports detected Oct 3 16:01:59 nimitz kernel: [ 180.600101] usb 3-4: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.600144] usb usb3: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.600147] usb usb3: usbdev_ioctl: CONNECTINFO Oct 3 16:01:59 nimitz kernel: [ 180.600167] usb 3-4: opened by process 6485: hald-addon-usb- Oct 3 16:01:59 nimitz kernel: [ 180.600170] usb 3-4: usbdev_ioctl: IOCTL
Quoted 6 lines
Quoted 1 line
Without a usbmon log, I can't tell what may still be going wrong.
This log should have recorded what was going on there. Was there something else that I should be capturing with usbmon that I missed?
That file is the usbmon log from back on Friday. I need to see the usbmon log you get with the timing fix installed. Was that not clear? Without the log, I can't tell why the disconnects continue to occur even though the timing fix should have eliminated them.
Alan Stern
Quoted 4 lines · Alan Stern
That file is the usbmon log from back on Friday. I need to see the usbmon log you get with the timing fix installed. Was that not clear? Without the log, I can't tell why the disconnects continue to occur even though the timing fix should have eliminated them.
It looks like I didn't properly apply the timing fix when I said I did last time. With Thomas/Hugh's fix applied, I don't see the disconnects any more. I'll keep an eye out and let everyone know if they reappear.
Thanks for all the excellent debugging, everyone!
-- Dave
Quoted 4 lines · Alan Stern
You should use usbmon (see
Documentation/usb/usbmon.txt) to record a trace of everything happening on bus 3. And to keep things simple, you should unplug all the USB devices except for one of the magical disappearing hubs.
Better still, get two traces: one from each kernel. Then they can be compared.
Alan Stern
Quoted 8 lines · Alan Stern
Quoted 4 lines · Alan Stern
You should use usbmon (see
Documentation/usb/usbmon.txt) to record a trace of everything happening on bus 3. And to keep things simple, you should unplug all the USB devices except for one of the magical disappearing hubs.Better still, get two traces: one from each kernel. Then they can be compared.
What should I record on the good kernel? Just the devices being connected?
-- Dave
Quoted 7 lines · Dave Hansen
Quoted 6 lines · Alan Stern
Quoted 4 lines · Alan Stern
You should use usbmon (see
Documentation/usb/usbmon.txt) to record a trace of everything happening on bus 3. And to keep things simple, you should unplug all the USB devices except for one of the magical disappearing hubs.
Quoted 5 lines
Quoted 2 lines
Better still, get two traces: one from each kernel. Then they can be compared.
What should I record on the good kernel? Just the devices being connected?
Never mind; the first trace was good enough.
Alan Stern