Skip to contentSkip to conversation

serial: Rename driver vcth to vct to support other board variants

PATCH New Stefan Roese 2 participants 2 messages Dec 15, 2008 – Jan 24, 2009

lore
Share & tools
lore

Stefan Roese

author
#0 lore raw

PATCH 1/1 serial: Rename driver vcth to vct to support other board variants

Moved driver vcth.c to vct.c to better reflect the VCT board series. This driver is now used by the VCT platforms:

vct_premium
vct_platinum
vct_platinumsvc

Signed-off-by Stefan Roese <[email protected]>
---
 drivers/serial/Makefile          |    2 +-
 drivers/serial/{vcth.c => vct.c} |    8 ++++++--
 2 files changed, 7 insertions(+), 3 deletions(-)
 rename drivers/serial/{vcth.c => vct.c} (94%)
drivers/serial/Makefile +1 -1
index 17235ff..c7a1882 100644
@@ -38,7 +38,7 @@ COBJS-$(CONFIG_PL011_SERIAL) += serial_pl01x.o
 COBJS-$(CONFIG_XILINX_UARTLITE) += serial_xuartlite.o
 COBJS-$(CONFIG_SCIF_CONSOLE) += serial_sh.o
 COBJS-$(CONFIG_USB_TTY) += usbtty.o
-COBJS-$(CONFIG_VCTH_SERIAL) += vcth.o
+COBJS-$(CONFIG_VCT_SERIAL) += vct.o
 
 COBJS	:= $(sort $(COBJS-y))
 SRCS	:= $(COBJS:.o=.c)
drivers/serial/vct.c renamed from drivers/serial/vcth.c +6 -2
similarity index 94%
rename from drivers/serial/vcth.c
rename to drivers/serial/vct.c
index 2c847d0..556c114 100755
@@ -21,7 +21,11 @@
 #include <common.h>
 #include <asm/io.h>
 
+#ifdef CONFIG_VCT_PLATINUMAVC
+#define UART_1_BASE		0xBDC30000
+#else
 #define UART_1_BASE		0xBF89C000
+#endif
 
 #define	UART_RBR_OFF		0x00	/* receiver buffer reg		*/
 #define	UART_THR_OFF		0x00	/* transmit holding  reg	*/

@@ -53,7 +57,7 @@
 #define UART_7DATA_BITS		0x0002	/*   7 [bits]  1   bits   2	*/
 #define UART_8DATA_BITS		0x0003	/*   8 [bits]  1   bits   2	*/
 
-static void vcth_uart_set_baud_rate(u32 address, u32 dh, u32 dl)
+static void vct_uart_set_baud_rate(u32 address, u32 dh, u32 dl)
 {
 	u32 val = __raw_readl(UART_1_BASE + UART_LCR_OFF);
 

@@ -74,7 +78,7 @@ static void vcth_uart_set_baud_rate(u32 address, u32 dh, u32 dl)
 int serial_init(void)
 {
 	__raw_writel(UART_DIS_ALL_INTER, UART_1_BASE + UART_IER_OFF);
-	vcth_uart_set_baud_rate(UART_1_BASE, 0, UART_115200_BDR);
+	vct_uart_set_baud_rate(UART_1_BASE, 0, UART_115200_BDR);
 	__raw_writel(UART_8DATA_BITS, UART_1_BASE + UART_LCR_OFF);
 
 	return 0;
Signature · 1 line
1.6.0.5
Applied
#1 lore raw

PATCH 1/1 serial: Rename driver vcth to vct to support other board variants

Dear Stefan Roese,

Quoted 7 lines · In message <[email protected]> you wrote:

Moved driver vcth.c to vct.c to better reflect the VCT board series. This driver is now used by the VCT platforms:

vct_premium
vct_platinum
vct_platinumsvc

Quoted 6 lines
Signed-off-by Stefan Roese <[email protected]>
---
 drivers/serial/Makefile          |    2 +-
 drivers/serial/{vcth.c => vct.c} |    8 ++++++--
 2 files changed, 7 insertions(+), 3 deletions(-)
 rename drivers/serial/{vcth.c => vct.c} (94%)

Applied, thanks.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
For every complex problem, there is a solution that is simple,  neat,
and wrong.                                           -- H. L. Mencken