Memory not being reported
I'm running 2.6.28.1 on an i686 (slackware-12.1 for the most part) box. I recently added some extra memory, expanding from 2Gb to 4. Everything works as expected except that not all of the memory seems to be seen.
free returns:
total used free shared buffers
cached
Mem: 3374860 2099504 1275356 0 86612
1032024
-/+ buffers/cache: 980868 2393992
Swap: 497972 0 497972
and cat /proc/meminfo gives:
MemTotal: 3374860 kB MemFree: 1199184 kB Buffers: 86816 kB Cached: 1036240 kB SwapCached: 0 kB Active: 1375864 kB
etc.
On the other hand, user-space tools like lshw show the 4 1Gb DIMMS as does the BIOS configuration boot menu.
One suspicion is that the configure option CONFIG_HIGHMEM4G=y should be unset and the CONFIG_HIGHMEM64G should be.
Any help would be appreciated, as would a separate CC since I don't subscribe to the list.
Thanks in advance
David
Quoted 3 lines · David Ronis
I'm running 2.6.28.1 on an i686 (slackware-12.1 for the most part) box. I recently added some extra memory, expanding from 2Gb to 4. Everything works as expected except that not all of the memory seems to be seen.
I'm running on 2.6.24.3 right now which is irrelevent. Is your system x86_64 capable? This specific machine is not. It's an older dual xeon 533mhz fsb.
Quoted 8 lines
free returns:
total used free shared buffers
cached
Mem: 3374860 2099504 1275356 0 86612
1032024
-/+ buffers/cache: 980868 2393992
Swap: 497972 0 497972
total used free shared buffers cached
Mem: 4019196 1342956 2676240 0 405712 223672
-/+ buffers/cache: 713572 3305624
Swap: 0 0 0
Quoted 2 lines
On the other hand, user-space tools like lshw show the 4 1Gb DIMMS as does the BIOS configuration boot menu.
lshw IIRC uses dmi information to obtain that information.
Quoted 2 lines
One suspicion is that the configure option
CONFIG_HIGHMEM4G=yshould be unset and theCONFIG_HIGHMEM64Gshould be.
# grep HIGH .config # CONFIG_HIGH_RES_TIMERS is not set # CONFIG_NOHIGHMEM is not set # CONFIG_HIGHMEM4G is not set CONFIG_HIGHMEM64G=y CONFIG_HIGHMEM=y # CONFIG_HIGHPTE is not set #
I see no reason not to use highmem 64gb I've used it on several of my systems, even ones that can't handle more than 2gb w/o problems.
One thing I have noticed (which is irrelevent to your question) is that I see about 100mb less memory running a 64-bit kernel vs a 32-bit kernel on 2 systems (different brand of motherboard) and 4gb. One was upgraded to 8gb; 32-bit shows about 8400000kb memory and running 64-bit shows about 8200000kb memory. Noone has answered my question as to why that is.
Signature · 2 lines
Lab tests show that use of micro$oft causes cancer in lab animals Got Gas???
Quoted 4 lines · David Ronis
I'm running 2.6.28.1 on an i686 (slackware-12.1 for the most part) box. I recently added some extra memory, expanding from 2Gb to 4. Everything works as expected except that not all of the memory seems to be seen.
I've got a comparable system, and could only see about 3G of the installed 4G.
Quoted 2 lines
One suspicion is that the configure option
CONFIG_HIGHMEM4G=yshould be unset and theCONFIG_HIGHMEM64Gshould be.
Indeed, using CONFIG_HIGHMEM64G does the trick for me, 4G usuable.
(I've also CONFIG_RESOURCES_64BIT set, maybe that's needed as well)
Signature · 1 line
left blank, right bald
Quoted 23 lines · David Ronis
I'm running 2.6.28.1 on an i686 (slackware-12.1 for the most part) box. I recently added some extra memory, expanding from 2Gb to 4. Everything works as expected except that not all of the memory seems to be seen.
free returns:
total used free shared buffers
cached
Mem: 3374860 2099504 1275356 0 86612
1032024
-/+ buffers/cache: 980868 2393992
Swap: 497972 0 497972and cat
/proc/meminfogives:MemTotal: 3374860 kB MemFree: 1199184 kB Buffers: 86816 kB Cached: 1036240 kB SwapCached: 0 kB Active: 1375864 kB
Quoted 7 lines
etc.
On the other hand, user-space tools like lshw show the 4 1Gb DIMMS as does the BIOS configuration boot menu.
One suspicion is that the configure option
CONFIG_HIGHMEM4G=yshould be unset and theCONFIG_HIGHMEM64Gshould be.
Yes, it should be. However, if your chipset doesn't support remapping memory above the 4GB mark (some don't, and this is needed in this case because various IO areas use up some of the address space below 4GB) then it won't be possible to make use of any of that RAM.
Note that when running with more than 4GB of RAM it's generally preferable to run a 64-bit kernel if the machine supports it.
Quoted 8 lines
Any help would be appreciated, as would a separate CC since I don't subscribe to the list.
Thanks in advance
David
I don't think this is a 64bit capable box. Nonetheless, there are only 4G of memory, not more, and I still see 3G of it.
David
Quoted 49 lines · Robert Hancock
Quoted 23 lines · David Ronis
I'm running 2.6.28.1 on an i686 (slackware-12.1 for the most part) box. I recently added some extra memory, expanding from 2Gb to 4. Everything works as expected except that not all of the memory seems to be seen.
free returns:
total used free shared buffers
cached
Mem: 3374860 2099504 1275356 0 86612
1032024
-/+ buffers/cache: 980868 2393992
Swap: 497972 0 497972and cat
/proc/meminfogives:MemTotal: 3374860 kB MemFree: 1199184 kB Buffers: 86816 kB Cached: 1036240 kB SwapCached: 0 kB Active: 1375864 kBQuoted 7 lines
etc.
On the other hand, user-space tools like lshw show the 4 1Gb DIMMS as does the BIOS configuration boot menu.
One suspicion is that the configure option
CONFIG_HIGHMEM4G=yshould be unset and theCONFIG_HIGHMEM64Gshould be.Yes, it should be. However, if your chipset doesn't support remapping memory above the 4GB mark (some don't, and this is needed in this case because various IO areas use up some of the address space below 4GB) then it won't be possible to make use of any of that RAM.
Note that when running with more than 4GB of RAM it's generally preferable to run a 64-bit kernel if the machine supports it.
Quoted 8 lines
Any help would be appreciated, as would a separate CC since I don't subscribe to the list.
Thanks in advance
David
Quoted 2 lines · David Ronis
I don't think this is a 64bit capable box. Nonetheless, there are only 4G of memory, not more, and I still see 3G of it.
Can you post your dmesg output from bootup?
Quoted 49 lines
David
Quoted 42 lines · Robert Hancock
Quoted 23 lines · David Ronis
I'm running 2.6.28.1 on an i686 (slackware-12.1 for the most part) box. I recently added some extra memory, expanding from 2Gb to 4. Everything works as expected except that not all of the memory seems to be seen.
free returns:
total used free shared buffers
cached
Mem: 3374860 2099504 1275356 0 86612
1032024
-/+ buffers/cache: 980868 2393992
Swap: 497972 0 497972and cat
/proc/meminfogives:MemTotal: 3374860 kB MemFree: 1199184 kB Buffers: 86816 kB Cached: 1036240 kB SwapCached: 0 kB Active: 1375864 kBQuoted 7 lines
etc.
On the other hand, user-space tools like lshw show the 4 1Gb DIMMS as does the BIOS configuration boot menu.
One suspicion is that the configure option
CONFIG_HIGHMEM4G=yshould be unset and theCONFIG_HIGHMEM64Gshould be.Yes, it should be. However, if your chipset doesn't support remapping memory above the 4GB mark (some don't, and this is needed in this case because various IO areas use up some of the address space below 4GB) then it won't be possible to make use of any of that RAM.
Note that when running with more than 4GB of RAM it's generally preferable to run a 64-bit kernel if the machine supports it.
Quoted 7 lines
Any help would be appreciated, as would a separate CC since I don't subscribe to the list.
Thanks in advance
David