Skip to contentSkip to conversation

sfc: SFT9001: Include non-breaking cable diagnostics in online self-tests

PATCH Applied Ben Hutchings 2 participants 18 messages Feb 27, 2009 – Mar 2, 2009

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/9 sfc: SFT9001: Include non-breaking cable diagnostics in online self-tests

---
 drivers/net/sfc/tenxpress.c |   45 ++++++++++++++++++++++--------------------
 1 files changed, 24 insertions(+), 21 deletions(-)
drivers/net/sfc/tenxpress.c +24 -21
index 5b0f451..23583ba 100644
@@ -679,12 +679,10 @@ static int sft9001_run_tests(struct efx_nic *efx, int *results, unsigned flags)
 {
 	struct ethtool_cmd ecmd;
 	int phy_id = efx->mii.phy_id;
-	int rc = 0, rc2, i, res_reg;
+	int rc = 0, rc2, i, ctrl_reg, res_reg;
 
-	if (!(flags & ETH_TEST_FL_OFFLINE))
-		return 0;
-
-	efx->phy_op->get_settings(efx, &ecmd);
+	if (flags & ETH_TEST_FL_OFFLINE)
+		efx->phy_op->get_settings(efx, &ecmd);
 
 	/* Initialise cable diagnostic results to unknown failure */
 	for (i = 1; i < 9; ++i)
@@ -692,18 +690,22 @@ static int sft9001_run_tests(struct efx_nic *efx, int *results, unsigned flags)
 
 	/* Run cable diagnostics; wait up to 5 seconds for them to complete.
 	 * A cable fault is not a self-test failure, but a timeout is. */
+	ctrl_reg = ((1 << CDIAG_CTRL_IMMED_LBN) |
+		    (CDIAG_CTRL_LEN_METRES << CDIAG_CTRL_LEN_UNIT_LBN));
+	if (flags & ETH_TEST_FL_OFFLINE) {
+		/* Break the link in order to run full diagnostics.  We
+		 * must reset the PHY to resume normal service. */
+		ctrl_reg |= (1 << CDIAG_CTRL_BRK_LINK_LBN);
+	}
 	mdio_clause45_write(efx, phy_id, MDIO_MMD_PMAPMD,
-			    PMA_PMD_CDIAG_CTRL_REG,
-			    (1 << CDIAG_CTRL_IMMED_LBN) |
-			    (1 << CDIAG_CTRL_BRK_LINK_LBN) |
-			    (CDIAG_CTRL_LEN_METRES << CDIAG_CTRL_LEN_UNIT_LBN));
+			    PMA_PMD_CDIAG_CTRL_REG, ctrl_reg);
 	i = 0;
 	while (mdio_clause45_read(efx, phy_id, MDIO_MMD_PMAPMD,
 				  PMA_PMD_CDIAG_CTRL_REG) &
 	       (1 << CDIAG_CTRL_IN_PROG_LBN)) {
 		if (++i == 50) {
 			rc = -ETIMEDOUT;
-			goto reset;
+			goto out;
 		}
 		msleep(100);
 	}
@@ -728,17 +730,18 @@ static int sft9001_run_tests(struct efx_nic *efx, int *results, unsigned flags)
 			results[5 + i] = len_reg;
 	}
 
-	/* We must reset to exit cable diagnostic mode.  The BIST will
-	 * also run when we do this. */
-reset:
-	rc2 = tenxpress_special_reset(efx);
-	results[0] = rc2 ? -1 : 1;
-	if (!rc)
-		rc = rc2;
-
-	rc2 = efx->phy_op->set_settings(efx, &ecmd);
-	if (!rc)
-		rc = rc2;
+out:
+	if (flags & ETH_TEST_FL_OFFLINE) {
+		/* Reset, running the BIST and then resuming normal service. */
+		rc2 = tenxpress_special_reset(efx);
+		results[0] = rc2 ? -1 : 1;
+		if (!rc)
+			rc = rc2;
+
+		rc2 = efx->phy_op->set_settings(efx, &ecmd);
+		if (!rc)
+			rc = rc2;
+	}
 
 	return rc;
 }
Signature · 3 lines
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
#1 lore raw

PATCH 2/9 sfc: Fix test for MDIO read failure

Commit 27dd2caca4eabe7c13a052b7456495ba75535e6a changed mdio_clause45_check_mmds() to read both DEVS0 and DEVS1 registers and to combine their values into an unsigned 32-bit mask. This made the following test for a negative (failure) value useless. Fix it to check whether either read failed.

---
 drivers/net/sfc/mdio_10g.c |   13 +++++++------
 1 files changed, 7 insertions(+), 6 deletions(-)
drivers/net/sfc/mdio_10g.c +7 -6
index f9e2f95..4462fb5 100644
@@ -125,24 +125,25 @@ int mdio_clause45_wait_reset_mmds(struct efx_nic *efx,
 int mdio_clause45_check_mmds(struct efx_nic *efx,
 			     unsigned int mmd_mask, unsigned int fatal_mask)
 {
+	int mmd = 0, probe_mmd, devs0, devs1;
 	u32 devices;
-	int mmd = 0, probe_mmd;
 
 	/* Historically we have probed the PHYXS to find out what devices are
 	 * present,but that doesn't work so well if the PHYXS isn't expected
 	 * to exist, if so just find the first item in the list supplied. */
 	probe_mmd = (mmd_mask & MDIO_MMDREG_DEVS_PHYXS) ? MDIO_MMD_PHYXS :
 	    __ffs(mmd_mask);
-	devices = (mdio_clause45_read(efx, efx->mii.phy_id,
-				      probe_mmd, MDIO_MMDREG_DEVS0) |
-		   mdio_clause45_read(efx, efx->mii.phy_id,
-				      probe_mmd, MDIO_MMDREG_DEVS1) << 16);
 
 	/* Check all the expected MMDs are present */
-	if (devices < 0) {
+	devs0 = mdio_clause45_read(efx, efx->mii.phy_id,
+				   probe_mmd, MDIO_MMDREG_DEVS0);
+	devs1 = mdio_clause45_read(efx, efx->mii.phy_id,
+				   probe_mmd, MDIO_MMDREG_DEVS1);
+	if (devs0 < 0 || devs1 < 0) {
 		EFX_ERR(efx, "failed to read devices present\n");
 		return -EIO;
 	}
+	devices = devs0 | (devs1 << 16);
 	if ((devices & mmd_mask) != mmd_mask) {
 		EFX_ERR(efx, "required MMDs not present: got %x, "
 			"wanted %x\n", devices, mmd_mask);
Signature · 3 lines
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
#3 lore raw

PATCH 3/9 sfc: SFT9001/SFN4111T: Check PHY boot status during board initialisation

In reply to Ben Hutchings

During SFN4111T initialisation, check whether the PHY boot status indicates a bad firmware checksum. If so, prepare to reflash rather than continuing with normal initialisation.

Remove redundant PHY boot status check from tenxpress_phy_init().

---
 drivers/net/sfc/phy.h       |    4 ++
 drivers/net/sfc/sfe4001.c   |   20 +++++++---
 drivers/net/sfc/tenxpress.c |   90 ++++++++++++++++++++++++++-----------------
 3 files changed, 73 insertions(+), 41 deletions(-)
drivers/net/sfc/phy.h +4 -0
index 07e855c..f6e4722 100644
@@ -18,6 +18,10 @@ extern struct efx_phy_operations falcon_sft9001_phy_ops;
 
 extern void tenxpress_phy_blink(struct efx_nic *efx, bool blink);
 
+/* Wait for the PHY to boot. Return 0 on success, -EINVAL if the PHY failed
+ * to boot due to corrupt flash, or some other negative error code. */
+extern int sft9001_wait_boot(struct efx_nic *efx);
+
 /****************************************************************************
  * Exported functions from the driver for XFP optical PHYs
  */
drivers/net/sfc/sfe4001.c +14 -6
index c0e9068..4eac5da 100644
@@ -399,6 +399,7 @@ static struct i2c_board_info sfn4111t_r5_hwmon_info = {
 
 int sfn4111t_init(struct efx_nic *efx)
 {
+	int i = 0;
 	int rc;
 
 	efx->board_info.hwmon_client =
@@ -417,13 +418,20 @@ int sfn4111t_init(struct efx_nic *efx)
 	if (rc)
 		goto fail_hwmon;
 
-	if (efx->phy_mode & PHY_MODE_SPECIAL) {
-		efx_stats_disable(efx);
-		sfn4111t_reset(efx);
-	}
-
-	return 0;
+	do {
+		if (efx->phy_mode & PHY_MODE_SPECIAL) {
+			/* PHY may not generate a 156.25 MHz clock and MAC
+			 * stats fetch will fail. */
+			efx_stats_disable(efx);
+			sfn4111t_reset(efx);
+		}
+		rc = sft9001_wait_boot(efx);
+		if (rc == 0)
+			return 0;
+		efx->phy_mode = PHY_MODE_SPECIAL;
+	} while (rc == -EINVAL && ++i < 2);
 
+	device_remove_file(&efx->pci_dev->dev, &dev_attr_phy_flash_cfg);
 fail_hwmon:
 	i2c_unregister_device(efx->board_info.hwmon_client);
 	return rc;
drivers/net/sfc/tenxpress.c +54 -34

125 lines not on this page · raw message

Signature · 3 lines
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
#5 lore raw

PATCH 4/9 sfc: Remove "XFP" from log messages that are not specific to XFP

In reply to Ben Hutchings
---
 drivers/net/sfc/xfp_phy.c |    8 ++++----
 1 files changed, 4 insertions(+), 4 deletions(-)
drivers/net/sfc/xfp_phy.c +4 -4
index 2d50b6e..5d1c7f8 100644
@@ -73,7 +73,7 @@ static int xfp_reset_phy(struct efx_nic *efx)
 	return rc;
 
  fail:
-	EFX_ERR(efx, "XFP: reset timed out!\n");
+	EFX_ERR(efx, "PHY reset timed out\n");
 	return rc;
 }
 
@@ -88,15 +88,15 @@ static int xfp_phy_init(struct efx_nic *efx)
 		return -ENOMEM;
 	efx->phy_data = phy_data;
 
-	EFX_INFO(efx, "XFP: PHY ID reg %x (OUI %x model %x revision"
-		 " %x)\n", devid, MDIO_ID_OUI(devid), MDIO_ID_MODEL(devid),
+	EFX_INFO(efx, "PHY ID reg %x (OUI %x model %x revision %x)\n",
+		 devid, MDIO_ID_OUI(devid), MDIO_ID_MODEL(devid),
 		 MDIO_ID_REV(devid));
 
 	phy_data->phy_mode = efx->phy_mode;
 
 	rc = xfp_reset_phy(efx);
 
-	EFX_INFO(efx, "XFP: PHY init %s.\n",
+	EFX_INFO(efx, "PHY init %s.\n",
 		 rc ? "failed" : "successful");
 	if (rc < 0)
 		goto fail;
Signature · 3 lines
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
#7 lore raw

PATCH 5/9 sfc: Fix reporting of PHY id

In reply to Ben Hutchings

Shuffle bits of the OUI into the conventional written order.

Replace PHY id component macros with functions.

Zero-pad PHY id components in log messages.

---
 drivers/net/sfc/mdio_10g.c |   15 +++++++++++++++
 drivers/net/sfc/mdio_10g.h |    8 ++++----
 drivers/net/sfc/xfp_phy.c  |    6 +++---
 3 files changed, 22 insertions(+), 7 deletions(-)
drivers/net/sfc/mdio_10g.c +15 -0
index 4462fb5..9f5ec3e 100644
@@ -17,6 +17,21 @@
 #include "boards.h"
 #include "workarounds.h"
 
+unsigned mdio_id_oui(u32 id)
+{
+	unsigned oui = 0;
+	int i;
+
+	/* The bits of the OUI are designated a..x, with a=0 and b variable.
+	 * In the id register c is the MSB but the OUI is conventionally
+	 * written as bytes h..a, p..i, x..q.  Reorder the bits accordingly. */
+	for (i = 0; i < 22; ++i)
+		if (id & (1 << (i + 10)))
+			oui |= 1 << (i ^ 7);
+
+	return oui;
+}
+
 int mdio_clause45_reset_mmd(struct efx_nic *port, int mmd,
 			    int spins, int spintime)
 {
drivers/net/sfc/mdio_10g.h +4 -4
index 8ba4977..7014d22 100644
@@ -70,10 +70,10 @@
 #define MDIO_MMDREG_STAT1_LPABLE_LBN	(1)
 #define MDIO_MMDREG_STAT1_LPABLE_WIDTH	(1)
 
-/* Bits in ID reg */
-#define MDIO_ID_REV(_id32)	(_id32 & 0xf)
-#define MDIO_ID_MODEL(_id32)	((_id32 >> 4) & 0x3f)
-#define MDIO_ID_OUI(_id32)	(_id32 >> 10)
+/* Bits in combined ID regs */
+static inline unsigned mdio_id_rev(u32 id) { return id & 0xf; }
+static inline unsigned mdio_id_model(u32 id) { return (id >> 4) & 0x3f; }
+extern unsigned mdio_id_oui(u32 id);
 
 /* Bits in MMDREG_DEVS0/1. Someone thoughtfully layed things out
  * so the 'bit present' bit number of an MMD is the number of
drivers/net/sfc/xfp_phy.c +3 -3
index 5d1c7f8..2df467d 100644
@@ -88,9 +88,9 @@ static int xfp_phy_init(struct efx_nic *efx)
 		return -ENOMEM;
 	efx->phy_data = phy_data;
 
-	EFX_INFO(efx, "PHY ID reg %x (OUI %x model %x revision %x)\n",
-		 devid, MDIO_ID_OUI(devid), MDIO_ID_MODEL(devid),
-		 MDIO_ID_REV(devid));
+	EFX_INFO(efx, "PHY ID reg %x (OUI %06x model %02x revision %x)\n",
+		 devid, mdio_id_oui(devid), mdio_id_model(devid),
+		 mdio_id_rev(devid));
 
 	phy_data->phy_mode = efx->phy_mode;
 
Signature · 3 lines
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
#9 lore raw

PATCH 6/9 sfc: Add support for QT2025C PHY

In reply to Ben Hutchings

This is a new PHY supporting SFP+ modules, used in the SFN4112F reference design. It is similar to the QT2022C2 and shares much of its support code.

---
 drivers/net/sfc/falcon.c     |    1 +
 drivers/net/sfc/net_driver.h |    1 +
 drivers/net/sfc/phy.h        |    4 +-
 drivers/net/sfc/xfp_phy.c    |   95 ++++++++++++++++++++++++++++++++++++++----
 4 files changed, 91 insertions(+), 10 deletions(-)
drivers/net/sfc/falcon.c +1 -0
index d5378e6..9e2f0f0 100644
@@ -2249,6 +2249,7 @@ static int falcon_probe_phy(struct efx_nic *efx)
 		efx->phy_op = &falcon_sft9001_phy_ops;
 		break;
 	case PHY_TYPE_QT2022C2:
+	case PHY_TYPE_QT2025C:
 		efx->phy_op = &falcon_xfp_phy_ops;
 		break;
 	default:
drivers/net/sfc/net_driver.h +1 -0
index 19930ff..eb768fc 100644
@@ -450,6 +450,7 @@ enum phy_type {
 	PHY_TYPE_QT2022C2 = 4,
 	PHY_TYPE_PM8358 = 6,
 	PHY_TYPE_SFT9001A = 8,
+	PHY_TYPE_QT2025C = 9,
 	PHY_TYPE_SFT9001B = 10,
 	PHY_TYPE_MAX	/* Insert any new items before this */
 };
drivers/net/sfc/phy.h +2 -2
index f6e4722..c1cff9c 100644
@@ -23,11 +23,11 @@ extern void tenxpress_phy_blink(struct efx_nic *efx, bool blink);
 extern int sft9001_wait_boot(struct efx_nic *efx);
 
 /****************************************************************************
- * Exported functions from the driver for XFP optical PHYs
+ * AMCC/Quake QT20xx PHYs
  */
 extern struct efx_phy_operations falcon_xfp_phy_ops;
 
-/* The QUAKE XFP PHY provides various H/W control states for LEDs */
+/* These PHYs provide various H/W control states for LEDs */
 #define QUAKE_LED_LINK_INVAL	(0)
 #define QUAKE_LED_LINK_STAT	(1)
 #define QUAKE_LED_LINK_ACT	(2)
drivers/net/sfc/xfp_phy.c +87 -8

126 lines not on this page · raw message

Signature · 3 lines
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
#11 lore raw

PATCH 7/9 sfc: Delete unused efx_blinker::led_num field

In reply to Ben Hutchings
---
 drivers/net/sfc/boards.c     |    1 -
 drivers/net/sfc/net_driver.h |    2 --
 2 files changed, 0 insertions(+), 3 deletions(-)
drivers/net/sfc/boards.c +0 -1
index 6490349..1260875 100644
@@ -194,7 +194,6 @@ static int sfe4002_init_leds(struct efx_nic *efx)
 	xfp_set_led(efx, SFE4002_RX_LED,
 		    QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACTSTAT);
 	xfp_set_led(efx, SFE4002_FAULT_LED, QUAKE_LED_OFF);
-	efx->board_info.blinker.led_num = SFE4002_FAULT_LED;
 	return 0;
 }
 
drivers/net/sfc/net_driver.h +0 -2
index eb768fc..ebc7b63 100644
@@ -385,13 +385,11 @@ struct efx_channel {
 
 /**
  * struct efx_blinker - S/W LED blinking context
- * @led_num: LED ID (board-specific meaning)
  * @state: Current state - on or off
  * @resubmit: Timer resubmission flag
  * @timer: Control timer for blinking
  */
 struct efx_blinker {
-	int led_num;
 	bool state;
 	bool resubmit;
 	struct timer_list timer;
Signature · 3 lines
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
#13 lore raw

PATCH 8/9 sfc: Clean up LED control

In reply to Ben Hutchings

Reinitialise LEDs after overriding them for identification.

Rename set_fault_led method to set_id_led since we always use it for NIC identification and not faults.

---
 drivers/net/sfc/boards.c     |   11 +++++------
 drivers/net/sfc/efx.c        |    4 ++--
 drivers/net/sfc/net_driver.h |    8 ++++----
 3 files changed, 11 insertions(+), 12 deletions(-)
drivers/net/sfc/boards.c +5 -6
index 1260875..b709878 100644
@@ -26,7 +26,7 @@ static void blink_led_timer(unsigned long context)
 {
 	struct efx_nic *efx = (struct efx_nic *)context;
 	struct efx_blinker *bl = &efx->board_info.blinker;
-	efx->board_info.set_fault_led(efx, bl->state);
+	efx->board_info.set_id_led(efx, bl->state);
 	bl->state = !bl->state;
 	if (bl->resubmit)
 		mod_timer(&bl->timer, jiffies + BLINK_INTERVAL);
@@ -48,7 +48,7 @@ static void board_blink(struct efx_nic *efx, bool blink)
 		blinker->resubmit = false;
 		if (blinker->timer.function)
 			del_timer_sync(&blinker->timer);
-		efx->board_info.set_fault_led(efx, false);
+		efx->board_info.init_leds(efx);
 	}
 }
 
@@ -185,7 +185,7 @@ static struct i2c_board_info sfe4002_hwmon_info = {
 #define SFE4002_RX_LED    (0)	/* Green */
 #define SFE4002_TX_LED    (1)	/* Amber */
 
-static int sfe4002_init_leds(struct efx_nic *efx)
+static void sfe4002_init_leds(struct efx_nic *efx)
 {
 	/* Set the TX and RX LEDs to reflect status and activity, and the
 	 * fault LED off */
@@ -194,10 +194,9 @@ static int sfe4002_init_leds(struct efx_nic *efx)
 	xfp_set_led(efx, SFE4002_RX_LED,
 		    QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACTSTAT);
 	xfp_set_led(efx, SFE4002_FAULT_LED, QUAKE_LED_OFF);
-	return 0;
 }
 
-static void sfe4002_fault_led(struct efx_nic *efx, bool state)
+static void sfe4002_set_id_led(struct efx_nic *efx, bool state)
 {
 	xfp_set_led(efx, SFE4002_FAULT_LED, state ? QUAKE_LED_ON :
 			QUAKE_LED_OFF);
@@ -221,7 +220,7 @@ static int sfe4002_init(struct efx_nic *efx)
 		return rc;
 	efx->board_info.monitor = sfe4002_check_hw;
 	efx->board_info.init_leds = sfe4002_init_leds;
-	efx->board_info.set_fault_led = sfe4002_fault_led;
+	efx->board_info.set_id_led = sfe4002_set_id_led;
 	efx->board_info.blink = board_blink;
 	efx->board_info.fini = efx_fini_lm87;
 	return 0;
drivers/net/sfc/efx.c +2 -2
index 7583659..45df110 100644
@@ -1848,8 +1848,8 @@ static struct efx_phy_operations efx_dummy_phy_operations = {
 
 static struct efx_board efx_dummy_board_info = {
 	.init		= efx_port_dummy_op_int,
-	.init_leds	= efx_port_dummy_op_int,
-	.set_fault_led	= efx_port_dummy_op_blink,
+	.init_leds	= efx_port_dummy_op_void,
+	.set_id_led	= efx_port_dummy_op_blink,
 	.monitor	= efx_port_dummy_op_int,
 	.blink		= efx_port_dummy_op_blink,
 	.fini		= efx_port_dummy_op_void,
drivers/net/sfc/net_driver.h +4 -4
index ebc7b63..b81fc72 100644
@@ -402,8 +402,8 @@ struct efx_blinker {
  * @major: Major rev. ('A', 'B' ...)
  * @minor: Minor rev. (0, 1, ...)
  * @init: Initialisation function
- * @init_leds: Sets up board LEDs
- * @set_fault_led: Turns the fault LED on or off
+ * @init_leds: Sets up board LEDs. May be called repeatedly.
+ * @set_id_led: Turns the identification LED on or off
  * @blink: Starts/stops blinking
  * @monitor: Board-specific health check function
  * @fini: Cleanup function
@@ -419,9 +419,9 @@ struct efx_board {
 	/* As the LEDs are typically attached to the PHY, LEDs
 	 * have a separate init callback that happens later than
 	 * board init. */
-	int (*init_leds)(struct efx_nic *efx);
+	void (*init_leds)(struct efx_nic *efx);
+	void (*set_id_led) (struct efx_nic *efx, bool state);
 	int (*monitor) (struct efx_nic *nic);
-	void (*set_fault_led) (struct efx_nic *efx, bool state);
 	void (*blink) (struct efx_nic *efx, bool start);
 	void (*fini) (struct efx_nic *nic);
 	struct efx_blinker blinker;
Signature · 3 lines
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
#15 lore raw

PATCH 9/9 sfc: Add support for SFN4112F SFP+ reference design

In reply to Ben Hutchings
---
 drivers/net/sfc/boards.c |   62 ++++++++++++++++++++++++++++++++++++++++++++++
 drivers/net/sfc/boards.h |    1 +
 2 files changed, 63 insertions(+), 0 deletions(-)
drivers/net/sfc/boards.c +62 -0
index b709878..5182ac5 100644
@@ -226,6 +226,66 @@ static int sfe4002_init(struct efx_nic *efx)
 	return 0;
 }
 
+/*****************************************************************************
+ * Support for the SFN4112F
+ *
+ */
+static u8 sfn4112f_lm87_channel = 0x03; /* use AIN not FAN inputs */
+
+static const u8 sfn4112f_lm87_regs[] = {
+	LM87_IN_LIMITS(0, 0x83, 0x91),		/* 2.5V:  1.8V +/- 5% */
+	LM87_IN_LIMITS(1, 0x51, 0x5a),		/* Vccp1: 1.2V +/- 5% */
+	LM87_IN_LIMITS(2, 0xb6, 0xca),		/* 3.3V:  3.3V +/- 5% */
+	LM87_IN_LIMITS(4, 0xb0, 0xe0),		/* 12V:   11-14V */
+	LM87_IN_LIMITS(5, 0x44, 0x4b),		/* Vccp2: 1.0V +/- 5% */
+	LM87_AIN_LIMITS(1, 0x91, 0xa1),		/* AIN2:  1.5V +/- 5% */
+	LM87_TEMP_INT_LIMITS(10, 60),		/* board */
+	LM87_TEMP_EXT1_LIMITS(10, 70),		/* Falcon */
+	0
+};
+
+static struct i2c_board_info sfn4112f_hwmon_info = {
+	I2C_BOARD_INFO("lm87", 0x2e),
+	.platform_data	= &sfn4112f_lm87_channel,
+	.irq		= -1,
+};
+
+#define SFN4112F_ACT_LED	0
+#define SFN4112F_LINK_LED	1
+
+static void sfn4112f_init_leds(struct efx_nic *efx)
+{
+	xfp_set_led(efx, SFN4112F_ACT_LED,
+		    QUAKE_LED_RXLINK | QUAKE_LED_LINK_ACT);
+	xfp_set_led(efx, SFN4112F_LINK_LED,
+		    QUAKE_LED_RXLINK | QUAKE_LED_LINK_STAT);
+}
+
+static void sfn4112f_set_id_led(struct efx_nic *efx, bool state)
+{
+	xfp_set_led(efx, SFN4112F_LINK_LED,
+		    state ? QUAKE_LED_ON : QUAKE_LED_OFF);
+}
+
+static int sfn4112f_check_hw(struct efx_nic *efx)
+{
+	/* Mask out unused sensors */
+	return efx_check_lm87(efx, ~0x48);
+}
+
+static int sfn4112f_init(struct efx_nic *efx)
+{
+	int rc = efx_init_lm87(efx, &sfn4112f_hwmon_info, sfn4112f_lm87_regs);
+	if (rc)
+		return rc;
+	efx->board_info.monitor = sfn4112f_check_hw;
+	efx->board_info.init_leds = sfn4112f_init_leds;
+	efx->board_info.set_id_led = sfn4112f_set_id_led;
+	efx->board_info.blink = board_blink;
+	efx->board_info.fini = efx_fini_lm87;
+	return 0;
+}
+
 /* This will get expanded as board-specific details get moved out of the
  * PHY drivers. */
 struct efx_board_data {
@@ -241,6 +301,8 @@ static struct efx_board_data board_data[] = {
 	{ EFX_BOARD_SFE4002, "SFE4002", "XFP adapter", sfe4002_init },
 	{ EFX_BOARD_SFN4111T, "SFN4111T", "100/1000/10GBASE-T adapter",
 	  sfn4111t_init },
+	{ EFX_BOARD_SFN4112F, "SFN4112F", "SFP+ adapter",
+	  sfn4112f_init },
 };
 
 void efx_set_board_info(struct efx_nic *efx, u16 revision_info)
drivers/net/sfc/boards.h +1 -0
index d93c6c6..44942de 100644
@@ -15,6 +15,7 @@ enum efx_board_type {
 	EFX_BOARD_SFE4001 = 1,
 	EFX_BOARD_SFE4002 = 2,
 	EFX_BOARD_SFN4111T = 0x51,
+	EFX_BOARD_SFN4112F = 0x52,
 };
 
 extern void efx_set_board_info(struct efx_nic *efx, u16 revision_info);
Signature · 3 lines
Ben Hutchings, Senior Software Engineer, Solarflare Communications
Not speaking for my employer; that's the marketing department's job.
They asked us to note that Solarflare product names are trademarked.
maintainer Applied
#2 lore raw

Re: [PATCH 2/9] sfc: Fix test for MDIO read failure

In reply to Ben Hutchings

From: Ben Hutchings <[email protected]>
Date: Fri, 27 Feb 2009 23:06:12 +0000

Quoted 7 lines

Commit 27dd2caca4eabe7c13a052b7456495ba75535e6a changed mdio_clause45_check_mmds() to read both DEVS0 and DEVS1 registers and to combine their values into an unsigned 32-bit mask. This made the following test for a negative (failure) value useless. Fix it to check whether either read failed.

Applied.

maintainer Applied
#4 lore raw

Re: [PATCH 3/9] sfc: SFT9001/SFN4111T: Check PHY boot status during board initialisation

In reply to Ben Hutchings

From: Ben Hutchings <[email protected]>
Date: Fri, 27 Feb 2009 23:06:45 +0000

Quoted 7 lines

During SFN4111T initialisation, check whether the PHY boot status indicates a bad firmware checksum. If so, prepare to reflash rather than continuing with normal initialisation.

Remove redundant PHY boot status check from tenxpress_phy_init().

Applied.