Loading both ehci-hcd and uhci-hcd drivers causes my printer to fail
Hi,
Short summary:
I have HP1018 printer, and it works well in windows. When I use in in linux, I often see messages like:
usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110
This is using hp backend that talks to printer using usbfs. I also tried usblp, but it just doesn't say anything in kernel log. I think it silently ignores similar errors, because the end result is the same, the printer sometimes works, but sometimes doesn't. (printer needs firmware to be uploaded to it, and I do upload it).
On the other hand, IF I remove _ether_ ehci-hcd or uhci-hcd from kernel, then everything works fine, I already rebooted the printer many times, used it to print, upload firmware, and everything just work, but as soon as I load the second driver it fails in same way again.
USB issues with this class of printers are nothing but new, for example see:
http://foo2zjs.rkkda.com/forum/read.php?9,374
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.15/+bug/54419
I compiled without CONFIG_USB_EHCI_ROOT_HUB_TT
and it did help (didn't that much testing, but at least firmware loads ok, and no error messages)
Looking for your comments,
Best regards,
Maxim Levitsky
Quoted 20 lines · Maxim Levitsky
Hi,
Short summary:
I have HP1018 printer, and it works well in windows. When I use in in linux, I often see messages like:
usbfs:
USBDEVFS_CONTROLfailed cmd python rqt 128 rq 6 len 255 ret -110This is using hp backend that talks to printer using usbfs. I also tried usblp, but it just doesn't say anything in kernel log. I think it silently ignores similar errors, because the end result is the same, the printer sometimes works, but sometimes doesn't. (printer needs firmware to be uploaded to it, and I do upload it).
On the other hand, IF I remove _ether_ ehci-hcd or uhci-hcd from kernel, then everything works fine, I already rebooted the printer many times, used it to print, upload firmware, and everything just work, but as soon as I load the second driver it fails in same way again.
Quoted 5 lines
USB issues with this class of printers are nothing but new, for example see:
http://foo2zjs.rkkda.com/forum/read.php?9,374
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.15/+bug/54419
What kernel version are you using?
Quoted 3 lines
I compiled without
CONFIG_USB_EHCI_ROOT_HUB_TT
and it did help (didn't that much testing, but at least firmware loads ok, and no error messages)
Can you provide the full kernel log messages from when you plug in your printer? Are there any other messages saying that you need to be sure to load one driver before the other?
thanks,
greg k-h
Quoted 29 lines · Greg KH
Quoted 20 lines · Maxim Levitsky
Hi,
Short summary:
I have HP1018 printer, and it works well in windows. When I use in in linux, I often see messages like:
usbfs:
USBDEVFS_CONTROLfailed cmd python rqt 128 rq 6 len 255 ret -110This is using hp backend that talks to printer using usbfs. I also tried usblp, but it just doesn't say anything in kernel log. I think it silently ignores similar errors, because the end result is the same, the printer sometimes works, but sometimes doesn't. (printer needs firmware to be uploaded to it, and I do upload it).
On the other hand, IF I remove _ether_ ehci-hcd or uhci-hcd from kernel, then everything works fine, I already rebooted the printer many times, used it to print, upload firmware, and everything just work, but as soon as I load the second driver it fails in same way again.
Quoted 5 lines
USB issues with this class of printers are nothing but new, for example see:
http://foo2zjs.rkkda.com/forum/read.php?9,374
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.15/+bug/54419What kernel version are you using?
Quoted 7 lines
Quoted 3 lines
I compiled without
CONFIG_USB_EHCI_ROOT_HUB_TT
and it did help (didn't that much testing, but at least firmware loads ok, and no error messages)Can you provide the full kernel log messages from when you plug in your printer? Are there any other messages saying that you need to be sure to load one driver before the other?
I am familiar with these messages, maybe instead uhci should depend on ehci or something like that?
Tommorow I try to load them manually in correct order. Btw, if I unload both and then load first ehci then uhci, this is ok (if they were loaded incorrectly)
Confirm again that without CONFIG_USB_EHCI_ROOT_HUB_TT both drivers work.
dmesg (from /var/log/kern.log.0) attached
It shows how I rebooted the printer often.
It also have this error message about the order.
But this isn't related.
I currently blacklisted uhci-hcd, so only ehci-hcd gets loaded. Then I loaded the uhci, and got same bug
(This is why I attached an older dmesg, if you need I reproduce that bug again)
To be clear, usually after these error messages (... -110), printer stops working, it is so confused, all attempts to access it hang. Only reboot helps.
Quoted 4 lines
thanks,
greg k-h
Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS EBDA/lowmem at: 0009fc00/0009fc00 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Initializing cgroup subsys cpuset Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Linux version 2.6.28 (maxim@maxim-laptop) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu12) ) #7 SMP PREEMPT Mon Feb 23 12:42:13 IST 2009 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Command line: root=UUID=ee43f3dd-ddf2-440c-82d0-3f5d32610f42 ro usbcore.autosuspend=1 vga=791 splash quiet Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] KERNEL supported cpus: Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Intel GenuineIntel Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-provided physical RAM map: Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 0000000000100000 - 000000007fcfd000 (usable) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 000000007fcfd000 - 000000007fd08000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 000000007fd08000 - 000000007fd52000 (usable) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 000000007fd52000 - 000000007fd55000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 000000007fd55000 - 000000007fdbb000 (usable) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 000000007fdbb000 - 000000007fdbf000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 000000007fdbf000 - 000000007fe70000 (usable) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 000000007fe70000 - 000000007febf000 (ACPI NVS) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 000000007febf000 - 000000007ff00000 (ACPI data) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 000000007ff00000 - 0000000080000000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] DMI 2.4 present. Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] last_pfn = 0x7fe70 max_arch_pfn = 0x3ffffffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] init_memory_mapping: 0000000000000000-000000007fe70000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] 0000000000 - 007fe00000 page 2M Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] 007fe00000 - 007fe70000 page 4k Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] kernel direct mapping tables up to 7fe70000 @ 8000-c000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] last_map_addr: 7fe70000 end: 7fe70000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] RAMDISK: 36a3c000 - 37fefe38 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: RSDP 000FE020, 0024 (r2 ACRSYS) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: XSDT 7FEFE120, 0064 (r1 ACRSYS ACRPRDCT 1 1000013) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: FACP 7FEFD000, 00F4 (r4 ACRSYS ACRPRDCT 1 MSFT 1000013) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: DSDT 7FEF4000, 8968 (r1 ACRSYS ACRPRDCT 1 MSFT 1000013) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: FACS 7FE75000, 0040 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: APIC 7FEF3000, 0068 (r2 ACRSYS ACRPRDCT 1 MSFT 1000013) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: MCFG 7FEF2000, 003C (r1 ACRSYS ACRPRDCT 1 MSFT 1000013) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: SLIC 7FEF1000, 0176 (r1 ACRSYS ACRPRDCT 1 MSFT 1000013) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: HPET 7FEF0000, 0038 (r1 ACRSYS ACRPRDCT 1 MSFT 1000013) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: SSDT 7FEEF000, 04C4 (r1 PmRef CpuPm 3000 INTL 20051117) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: SSDT 7FEEE000, 0232 (r1 PmRef Cpu0Tst 3000 INTL 20051117) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: SSDT 7FEED000, 00A0 (r1 PmRef Cpu1Tst 3000 INTL 20051117) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] (6 early reservations) ==> bootmem [0000000000 - 007fe70000] Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] #0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000] Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] #1 [0000006000 - 0000008000] TRAMPOLINE ==> [0000006000 - 0000008000] Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] #2 [0000200000 - 0000805e18] TEXT DATA BSS ==> [0000200000 - 0000805e18] Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] #3 [0036a3c000 - 0037fefe38] RAMDISK ==> [0036a3c000 - 0037fefe38] Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] #4 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000] Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] #5 [0000008000 - 000000a000] PGTABLE ==> [0000008000 - 000000a000] Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] found SMP MP-table at [ffff8800000fe1b0] 000fe1b0 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] [ffffe20000000000-ffffe20001bfffff] PMD -> [ffff880001200000-ffff880002dfffff] on node 0 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Zone PFN ranges: Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] DMA 0x00000000 -> 0x00001000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] DMA32 0x00001000 -> 0x00100000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Normal 0x00100000 -> 0x00100000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Movable zone start PFN for each node Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] early_node_map[5] active PFN ranges Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] 0: 0x00000000 -> 0x0000009f Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] 0: 0x00000100 -> 0x0007fcfd Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] 0: 0x0007fd08 -> 0x0007fd52 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] 0: 0x0007fd55 -> 0x0007fdbb Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] 0: 0x0007fdbf -> 0x0007fe70 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] On node 0 totalpages: 523773 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] DMA zone: 56 pages used for memmap Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] DMA zone: 1644 pages reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] DMA zone: 2299 pages, LIFO batch:0 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] DMA32 zone: 7107 pages used for memmap Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] DMA32 zone: 512667 pages, LIFO batch:31 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Normal zone: 0 pages used for memmap Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Movable zone: 0 pages used for memmap Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: PM-Timer IO Port: 0x408 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: Local APIC address 0xfee00000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1]) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1]) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] IOAPIC[0]: apic_id 4, version 0, address 0xfec00000, GSI 0-23 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: IRQ0 used by override. Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: IRQ2 used by override. Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: IRQ9 used by override. Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Using ACPI (MADT) for SMP configuration information Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] PM: Registered nosave memory: 000000007fcfd000 - 000000007fd08000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] PM: Registered nosave memory: 000000007fd52000 - 000000007fd55000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] PM: Registered nosave memory: 000000007fdbb000 - 000000007fdbf000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:60000000) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] PERCPU: Allocating 49152 bytes of per cpu data Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] NR_CPUS: 8, nr_cpu_ids: 2, nr_node_ids 1 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 514966 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Kernel command line: root=UUID=ee43f3dd-ddf2-440c-82d0-3f5d32610f42 ro usbcore.autosuspend=1 vga=791 splash quiet Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Unknown boot option `usbcore.autosuspend=1': ignoring Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Initializing CPU#0 Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Preemptible RCU implementation. Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Fast TSC calibration using PIT Mar 6 16:33:38 maxim-laptop kernel: [ 0.000000] Detected 1662.406 MHz processor. Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] Console: colour dummy device 80x25 Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] console [tty0] enabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] Memory: 2034076k/2095552k available (3165k kernel code, 460k absent, 60388k reserved, 1733k data, 364k init) Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] hpet clockevent registered Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] HPET: 3 timers in total, 0 timers will be used for per-cpu timer Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] Calibrating delay loop (skipped), value calculated using timer frequency.. 3324.81 BogoMIPS (lpj=6649624) Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] Security Framework initialized Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] SELinux: Disabled at boot. Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] Mount-cache hash table entries: 256 Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] Initializing cgroup subsys ns Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] Initializing cgroup subsys cpuacct Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] CPU: L2 cache: 2048K Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] CPU: Physical Processor ID: 0 Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] CPU: Processor Core ID: 0 Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] using mwait in idle threads. Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] ACPI: Core revision 20080926 Mar 6 16:33:38 maxim-laptop kernel: [ 0.016053] Setting APIC routing to flat Mar 6 16:33:38 maxim-laptop kernel: [ 0.016455] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1 Mar 6 16:33:38 maxim-laptop kernel: [ 0.059814] CPU0: Intel(R) Core(TM)2 Duo CPU T5450 @ 1.66GHz stepping 0d Mar 6 16:33:38 maxim-laptop kernel: [ 0.060001] Booting processor 1 APIC 0x1 ip 0x6000 Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] Initializing CPU#1 Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] Calibrating delay using timer specific routine.. 3324.94 BogoMIPS (lpj=6649898) Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] CPU: L1 I cache: 32K, L1 D cache: 32K Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] CPU: L2 cache: 2048K Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] CPU: Physical Processor ID: 0 Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] CPU: Processor Core ID: 1 Mar 6 16:33:38 maxim-laptop kernel: [ 0.004000] x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106 Mar 6 16:33:38 maxim-laptop kernel: [ 0.145321] CPU1: Intel(R) Core(TM)2 Duo CPU T5450 @ 1.66GHz stepping 0d Mar 6 16:33:38 maxim-laptop kernel: [ 0.145350] checking TSC synchronization [CPU#0 -> CPU#1]: passed. Mar 6 16:33:38 maxim-laptop kernel: [ 0.148023] Brought up 2 CPUs Mar 6 16:33:38 maxim-laptop kernel: [ 0.148026] Total of 2 processors activated (6649.76 BogoMIPS). Mar 6 16:33:38 maxim-laptop kernel: [ 0.148078] CPU0 attaching sched-domain: Mar 6 16:33:38 maxim-laptop kernel: [ 0.148081] domain 0: span 0-1 level MC Mar 6 16:33:38 maxim-laptop kernel: [ 0.148084] groups: 0 1 Mar 6 16:33:38 maxim-laptop kernel: [ 0.148089] CPU1 attaching sched-domain: Mar 6 16:33:38 maxim-laptop kernel: [ 0.148091] domain 0: span 0-1 level MC Mar 6 16:33:38 maxim-laptop kernel: [ 0.148094] groups: 1 0 Mar 6 16:33:38 maxim-laptop kernel: [ 0.148159] net_namespace: 1352 bytes Mar 6 16:33:38 maxim-laptop kernel: [ 0.148214] NET: Registered protocol family 16 Mar 6 16:33:38 maxim-laptop kernel: [ 0.148214] ACPI: bus type pci registered Mar 6 16:33:38 maxim-laptop kernel: [ 0.148214] PCI: Using configuration type 1 for base access Mar 6 16:33:38 maxim-laptop kernel: [ 0.153205] ACPI: EC: Look up EC in DSDT Mar 6 16:33:38 maxim-laptop kernel: [ 0.158615] ACPI: BIOS _OSI(Linux) query ignored Mar 6 16:33:38 maxim-laptop kernel: [ 0.160816] ACPI: EC: non-query interrupt received, switching to interrupt mode Mar 6 16:33:38 maxim-laptop kernel: [ 0.168026] ACPI: EC: GPE storm detected, transactions will use polling mode Mar 6 16:33:38 maxim-laptop kernel: [ 0.668005] ACPI: EC: missing confirmations, switch off interrupt mode. Mar 6 16:33:38 maxim-laptop kernel: [ 0.672235] ACPI: Interpreter enabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.672238] ACPI: (supports S0 S3 S4 S5) Mar 6 16:33:38 maxim-laptop kernel: [ 0.672261] ACPI: Using IOAPIC for interrupt routing Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] ACPI: EC: GPE = 0x1c, I/O: command/status = 0x66, data = 0x62 Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] ACPI: EC: driver started in poll mode Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] ACPI: PCI Root Bridge [PCI0] (0000:00) Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:01.0: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1a.0: reg 20 io port: [0x60c0-0x60df] Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1a.1: reg 20 io port: [0x60a0-0x60bf] Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1a.7: reg 10 32bit mmio: [0x9b304c00-0x9b304fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1a.7: PME# supported from D0 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1a.7: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1b.0: reg 10 64bit mmio: [0x9b300000-0x9b303fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1b.0: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1c.0: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1c.1: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1c.2: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.728846] pci 0000:00:1c.3: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.728886] pci 0000:00:1d.0: reg 20 io port: [0x6080-0x609f] Mar 6 16:33:38 maxim-laptop kernel: [ 0.728954] pci 0000:00:1d.1: reg 20 io port: [0x6060-0x607f] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729023] pci 0000:00:1d.2: reg 20 io port: [0x6040-0x605f] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729097] pci 0000:00:1d.7: reg 10 32bit mmio: [0x9b304800-0x9b304bff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729149] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.729155] pci 0000:00:1d.7: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.729328] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO Mar 6 16:33:38 maxim-laptop kernel: [ 0.729332] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO Mar 6 16:33:38 maxim-laptop kernel: [ 0.729372] pci 0000:00:1f.1: reg 10 io port: [0x6108-0x610f] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729380] pci 0000:00:1f.1: reg 14 io port: [0x611c-0x611f] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729389] pci 0000:00:1f.1: reg 18 io port: [0x6100-0x6107] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729397] pci 0000:00:1f.1: reg 1c io port: [0x6118-0x611b] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729406] pci 0000:00:1f.1: reg 20 io port: [0x60e0-0x60ef] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729485] pci 0000:00:1f.2: reg 10 io port: [0x60f8-0x60ff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729494] pci 0000:00:1f.2: reg 14 io port: [0x6114-0x6117] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729502] pci 0000:00:1f.2: reg 18 io port: [0x60f0-0x60f7] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729511] pci 0000:00:1f.2: reg 1c io port: [0x6110-0x6113] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729519] pci 0000:00:1f.2: reg 20 io port: [0x6020-0x603f] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729527] pci 0000:00:1f.2: reg 24 32bit mmio: [0x9b304000-0x9b3047ff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729550] pci 0000:00:1f.2: PME# supported from D3hot Mar 6 16:33:38 maxim-laptop kernel: [ 0.729555] pci 0000:00:1f.2: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.729591] pci 0000:00:1f.3: reg 10 32bit mmio: [0x9b305000-0x9b3050ff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729618] pci 0000:00:1f.3: reg 20 io port: [0x6000-0x601f] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729699] pci 0000:01:00.0: reg 10 32bit mmio: [0x92000000-0x92ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729716] pci 0000:01:00.0: reg 14 64bit mmio: [0x80000000-0x8fffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729733] pci 0000:01:00.0: reg 1c 64bit mmio: [0x90000000-0x91ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729743] pci 0000:01:00.0: reg 24 io port: [0x5000-0x507f] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729752] pci 0000:01:00.0: reg 30 32bit mmio: [0xfffe0000-0xffffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729834] pci 0000:00:01.0: bridge io port: [0x5000-0x5fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729837] pci 0000:00:01.0: bridge 32bit mmio: [0x90000000-0x92ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.729843] pci 0000:00:01.0: bridge 64bit mmio pref: [0x80000000-0x8fffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.0: bridge io port: [0x4000-0x4fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.0: bridge 32bit mmio: [0x9a300000-0x9b2fffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.0: bridge 64bit mmio pref: [0x93000000-0x93ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.1: bridge io port: [0x3000-0x3fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.1: bridge 32bit mmio: [0x99300000-0x9a2fffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.1: bridge 64bit mmio pref: [0x94000000-0x94ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:05:00.0: reg 10 64bit mmio: [0x98200000-0x9820ffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:05:00.0: PME# supported from D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:05:00.0: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.2: bridge io port: [0x2000-0x2fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.2: bridge 32bit mmio: [0x98200000-0x992fffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.2: bridge 64bit mmio pref: [0x95000000-0x95ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:06:00.0: reg 10 32bit mmio: [0x97100000-0x97100fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:06:00.0: PME# supported from D0 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:06:00.0: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.3: bridge io port: [0x1000-0x1fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.3: bridge 32bit mmio: [0x97100000-0x981fffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:00:1c.3: bridge 64bit mmio pref: [0x96000000-0x96ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.0: reg 10 32bit mmio: [0x97000000-0x970007ff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.0: supports D1 D2 Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.0: PME# supported from D0 D1 D2 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.0: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.1: reg 10 32bit mmio: [0x97000b00-0x97000bff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.1: supports D1 D2 Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.1: PME# supported from D0 D1 D2 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.1: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.2: reg 10 32bit mmio: [0x97000a00-0x97000aff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.2: supports D1 D2 Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.2: PME# supported from D0 D1 D2 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.732002] pci 0000:07:00.2: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.732034] pci 0000:07:00.3: reg 10 32bit mmio: [0x97000900-0x970009ff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732088] pci 0000:07:00.3: supports D1 D2 Mar 6 16:33:38 maxim-laptop kernel: [ 0.732090] pci 0000:07:00.3: PME# supported from D0 D1 D2 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.732095] pci 0000:07:00.3: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.732141] pci 0000:07:00.4: reg 10 32bit mmio: [0x97000800-0x970008ff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732194] pci 0000:07:00.4: supports D1 D2 Mar 6 16:33:38 maxim-laptop kernel: [ 0.732196] pci 0000:07:00.4: PME# supported from D0 D1 D2 D3hot D3cold Mar 6 16:33:38 maxim-laptop kernel: [ 0.732202] pci 0000:07:00.4: PME# disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.732278] pci 0000:00:1e.0: transparent bridge Mar 6 16:33:38 maxim-laptop kernel: [ 0.732287] pci 0000:00:1e.0: bridge 32bit mmio: [0x97000000-0x970fffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732333] bus 00 -> node 0 Mar 6 16:33:38 maxim-laptop kernel: [ 0.732341] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732774] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P32_._PRT] Mar 6 16:33:38 maxim-laptop kernel: [ 0.732969] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP2._PRT] Mar 6 16:33:38 maxim-laptop kernel: [ 0.733163] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP3._PRT] Mar 6 16:33:38 maxim-laptop kernel: [ 0.733358] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.EXP4._PRT] Mar 6 16:33:38 maxim-laptop kernel: [ 0.733563] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT] Mar 6 16:33:38 maxim-laptop kernel: [ 0.744473] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 9 10 *11 12) Mar 6 16:33:38 maxim-laptop kernel: [ 0.744473] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12) Mar 6 16:33:38 maxim-laptop kernel: [ 0.744473] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 9 10 *11 12) Mar 6 16:33:38 maxim-laptop kernel: [ 0.744571] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12) Mar 6 16:33:38 maxim-laptop kernel: [ 0.744752] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11 12) *0, disabled. Mar 6 16:33:38 maxim-laptop kernel: [ 0.744934] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 *10 11 12) Mar 6 16:33:38 maxim-laptop kernel: [ 0.745114] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 *11 12) Mar 6 16:33:38 maxim-laptop kernel: [ 0.745294] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 9 10 *11 12) Mar 6 16:33:38 maxim-laptop kernel: [ 0.745392] ACPI: WMI: Mapper loaded Mar 6 16:33:38 maxim-laptop kernel: [ 0.745392] SCSI subsystem initialized Mar 6 16:33:38 maxim-laptop kernel: [ 0.745392] PCI: Using ACPI for IRQ routing Mar 6 16:33:38 maxim-laptop kernel: [ 0.776062] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0 Mar 6 16:33:38 maxim-laptop kernel: [ 0.776067] hpet0: 3 comparators, 64-bit 14.318180 MHz counter Mar 6 16:33:38 maxim-laptop kernel: [ 0.784009] Switched to high resolution mode on CPU 0 Mar 6 16:33:38 maxim-laptop kernel: [ 0.785376] Switched to high resolution mode on CPU 1 Mar 6 16:33:38 maxim-laptop kernel: [ 0.829008] pnp: PnP ACPI init Mar 6 16:33:38 maxim-laptop kernel: [ 0.829021] ACPI: bus type pnp registered Mar 6 16:33:38 maxim-laptop kernel: [ 0.830351] pnp 00:01: io resource (0x164e-0x164f) overlaps 0000:00:1c.3 BAR 7 (0x1000-0x1fff), disabling Mar 6 16:33:38 maxim-laptop kernel: [ 0.853543] pnp: PnP ACPI: found 10 devices Mar 6 16:33:38 maxim-laptop kernel: [ 0.853546] ACPI: ACPI bus type pnp unregistered Mar 6 16:33:38 maxim-laptop kernel: [ 0.853556] system 00:01: ioport range 0x600-0x60f has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853559] system 00:01: ioport range 0x610-0x610 has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853562] system 00:01: ioport range 0x800-0x80f has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853565] system 00:01: ioport range 0x810-0x817 has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853567] system 00:01: ioport range 0x400-0x47f has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853570] system 00:01: ioport range 0x500-0x53f has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853573] system 00:01: iomem range 0xe0000000-0xefffffff has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853576] system 00:01: iomem range 0xfed1c000-0xfed1ffff has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853579] system 00:01: iomem range 0xfed14000-0xfed17fff has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853582] system 00:01: iomem range 0xfed18000-0xfed18fff has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853585] system 00:01: iomem range 0xfed19000-0xfed19fff has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853587] system 00:01: iomem range 0xfec00000-0xfec00fff has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853590] system 00:01: iomem range 0xfee00000-0xfee00fff has been reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.853593] system 00:01: iomem range 0x32000000-0x320000ff could not be reserved Mar 6 16:33:38 maxim-laptop kernel: [ 0.858721] pci 0000:01:00.0: BAR 6: can't allocate mem resource [0x90000000-0x8fffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858736] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858739] pci 0000:00:01.0: IO window: 0x5000-0x5fff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858744] pci 0000:00:01.0: MEM window: 0x90000000-0x92ffffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858748] pci 0000:00:01.0: PREFETCH window: 0x00000080000000-0x0000008fffffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858753] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858757] pci 0000:00:1c.0: IO window: 0x4000-0x4fff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858763] pci 0000:00:1c.0: MEM window: 0x9a300000-0x9b2fffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858769] pci 0000:00:1c.0: PREFETCH window: 0x00000093000000-0x00000093ffffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858777] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:04 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858781] pci 0000:00:1c.1: IO window: 0x3000-0x3fff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858788] pci 0000:00:1c.1: MEM window: 0x99300000-0x9a2fffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858793] pci 0000:00:1c.1: PREFETCH window: 0x00000094000000-0x00000094ffffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858802] pci 0000:00:1c.2: PCI bridge, secondary bus 0000:05 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858805] pci 0000:00:1c.2: IO window: 0x2000-0x2fff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858812] pci 0000:00:1c.2: MEM window: 0x98200000-0x992fffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858817] pci 0000:00:1c.2: PREFETCH window: 0x00000095000000-0x00000095ffffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858826] pci 0000:00:1c.3: PCI bridge, secondary bus 0000:06 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858829] pci 0000:00:1c.3: IO window: 0x1000-0x1fff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858836] pci 0000:00:1c.3: MEM window: 0x97100000-0x981fffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858841] pci 0000:00:1c.3: PREFETCH window: 0x00000096000000-0x00000096ffffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858850] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:07 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858852] pci 0000:00:1e.0: IO window: disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.858859] pci 0000:00:1e.0: MEM window: 0x97000000-0x970fffff Mar 6 16:33:38 maxim-laptop kernel: [ 0.858864] pci 0000:00:1e.0: PREFETCH window: disabled Mar 6 16:33:38 maxim-laptop kernel: [ 0.858880] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858885] pci 0000:00:01.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858894] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858899] pci 0000:00:1c.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858909] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858914] pci 0000:00:1c.1: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858924] pci 0000:00:1c.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858929] pci 0000:00:1c.2: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858940] pci 0000:00:1c.3: PCI INT D -> GSI 19 (level, low) -> IRQ 19 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858945] pci 0000:00:1c.3: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858953] pci 0000:00:1e.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 0.858958] bus: 00 index 0 io port: [0x00-0xffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858960] bus: 00 index 1 mmio: [0x000000-0xffffffffffffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858962] bus: 01 index 0 io port: [0x5000-0x5fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858965] bus: 01 index 1 mmio: [0x90000000-0x92ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858967] bus: 01 index 2 mmio: [0x80000000-0x8fffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858968] bus: 01 index 3 mmio: [0x0-0x0] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858970] bus: 02 index 0 io port: [0x4000-0x4fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858972] bus: 02 index 1 mmio: [0x9a300000-0x9b2fffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858974] bus: 02 index 2 mmio: [0x93000000-0x93ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858976] bus: 02 index 3 mmio: [0x0-0x0] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858978] bus: 04 index 0 io port: [0x3000-0x3fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858980] bus: 04 index 1 mmio: [0x99300000-0x9a2fffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858982] bus: 04 index 2 mmio: [0x94000000-0x94ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858984] bus: 04 index 3 mmio: [0x0-0x0] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858986] bus: 05 index 0 io port: [0x2000-0x2fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858988] bus: 05 index 1 mmio: [0x98200000-0x992fffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858990] bus: 05 index 2 mmio: [0x95000000-0x95ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858991] bus: 05 index 3 mmio: [0x0-0x0] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858993] bus: 06 index 0 io port: [0x1000-0x1fff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858995] bus: 06 index 1 mmio: [0x97100000-0x981fffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858997] bus: 06 index 2 mmio: [0x96000000-0x96ffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.858999] bus: 06 index 3 mmio: [0x0-0x0] Mar 6 16:33:38 maxim-laptop kernel: [ 0.859001] bus: 07 index 0 mmio: [0x0-0x0] Mar 6 16:33:38 maxim-laptop kernel: [ 0.859003] bus: 07 index 1 mmio: [0x97000000-0x970fffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.859005] bus: 07 index 2 mmio: [0x0-0x0] Mar 6 16:33:38 maxim-laptop kernel: [ 0.859007] bus: 07 index 3 io port: [0x00-0xffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.859009] bus: 07 index 4 mmio: [0x000000-0xffffffffffffffff] Mar 6 16:33:38 maxim-laptop kernel: [ 0.859019] NET: Registered protocol family 2 Mar 6 16:33:38 maxim-laptop kernel: [ 0.981055] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) Mar 6 16:33:38 maxim-laptop kernel: [ 0.981438] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) Mar 6 16:33:38 maxim-laptop kernel: [ 0.983423] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) Mar 6 16:33:38 maxim-laptop kernel: [ 0.983983] TCP: Hash tables configured (established 262144 bind 65536) Mar 6 16:33:38 maxim-laptop kernel: [ 0.983986] TCP reno registered Mar 6 16:33:38 maxim-laptop kernel: [ 1.029111] NET: Registered protocol family 1 Mar 6 16:33:38 maxim-laptop kernel: [ 1.029244] checking if image is initramfs... it is Mar 6 16:33:38 maxim-laptop kernel: [ 3.653982] Freeing initrd memory: 22223k freed Mar 6 16:33:38 maxim-laptop kernel: [ 3.667789] audit: initializing netlink socket (disabled) Mar 6 16:33:38 maxim-laptop kernel: [ 3.667805] type=2000 audit(1236350000.665:1): initialized Mar 6 16:33:38 maxim-laptop kernel: [ 3.672851] VFS: Disk quotas dquot_6.5.1 Mar 6 16:33:38 maxim-laptop kernel: [ 3.672937] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) Mar 6 16:33:38 maxim-laptop kernel: [ 3.672990] msgmni has been set to 4017 Mar 6 16:33:38 maxim-laptop kernel: [ 3.673293] alg: No test for stdrng (krng) Mar 6 16:33:38 maxim-laptop kernel: [ 3.673303] io scheduler noop registered Mar 6 16:33:38 maxim-laptop kernel: [ 3.673305] io scheduler anticipatory registered Mar 6 16:33:38 maxim-laptop kernel: [ 3.673307] io scheduler deadline registered Mar 6 16:33:38 maxim-laptop kernel: [ 3.673370] io scheduler cfq registered (default) Mar 6 16:33:38 maxim-laptop kernel: [ 3.674207] pci 0000:01:00.0: Boot video device Mar 6 16:33:38 maxim-laptop kernel: [ 3.674250] ACPI Warning (nseval-0168): Insufficient arguments - method [_OSC] needs 5, found 4 [20080926] Mar 6 16:33:38 maxim-laptop kernel: [ 3.674407] ACPI Warning (nspredef-0252): \_SB_.PCI0._OSC: Parameter count mismatch - ASL declared 5, expected 4 [20080926] Mar 6 16:33:38 maxim-laptop kernel: [ 3.697433] ACPI Warning (nseval-0168): Insufficient arguments - method [_OSC] needs 5, found 4 [20080926] Mar 6 16:33:38 maxim-laptop kernel: [ 3.720525] pcieport-driver 0000:00:01.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 3.720563] pcieport-driver 0000:00:01.0: found MSI capability Mar 6 16:33:38 maxim-laptop kernel: [ 3.720589] pcieport-driver 0000:00:01.0: irq 511 for MSI/MSI-X Mar 6 16:33:38 maxim-laptop kernel: [ 3.720599] pci_express 0000:00:01.0:pcie00: allocate port service Mar 6 16:33:38 maxim-laptop kernel: [ 3.720642] pci_express 0000:00:01.0:pcie02: allocate port service Mar 6 16:33:38 maxim-laptop kernel: [ 3.720724] pcieport-driver 0000:00:1c.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 3.720773] pcieport-driver 0000:00:1c.0: found MSI capability Mar 6 16:33:38 maxim-laptop kernel: [ 3.720809] pcieport-driver 0000:00:1c.0: irq 510 for MSI/MSI-X Mar 6 16:33:38 maxim-laptop kernel: [ 3.720827] pci_express 0000:00:1c.0:pcie00: allocate port service Mar 6 16:33:38 maxim-laptop kernel: [ 3.720865] pci_express 0000:00:1c.0:pcie02: allocate port service Mar 6 16:33:38 maxim-laptop kernel: [ 3.720972] pcieport-driver 0000:00:1c.1: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 3.721026] pcieport-driver 0000:00:1c.1: found MSI capability Mar 6 16:33:38 maxim-laptop kernel: [ 3.721062] pcieport-driver 0000:00:1c.1: irq 509 for MSI/MSI-X Mar 6 16:33:38 maxim-laptop kernel: [ 3.721079] pci_express 0000:00:1c.1:pcie00: allocate port service Mar 6 16:33:38 maxim-laptop kernel: [ 3.721115] pci_express 0000:00:1c.1:pcie02: allocate port service Mar 6 16:33:38 maxim-laptop kernel: [ 3.721216] pcieport-driver 0000:00:1c.2: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 3.721265] pcieport-driver 0000:00:1c.2: found MSI capability Mar 6 16:33:38 maxim-laptop kernel: [ 3.721301] pcieport-driver 0000:00:1c.2: irq 508 for MSI/MSI-X Mar 6 16:33:38 maxim-laptop kernel: [ 3.721318] pci_express 0000:00:1c.2:pcie00: allocate port service Mar 6 16:33:38 maxim-laptop kernel: [ 3.721352] pci_express 0000:00:1c.2:pcie02: allocate port service Mar 6 16:33:38 maxim-laptop kernel: [ 3.721452] pcieport-driver 0000:00:1c.3: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 3.721501] pcieport-driver 0000:00:1c.3: found MSI capability Mar 6 16:33:38 maxim-laptop kernel: [ 3.721536] pcieport-driver 0000:00:1c.3: irq 507 for MSI/MSI-X Mar 6 16:33:38 maxim-laptop kernel: [ 3.721554] pci_express 0000:00:1c.3:pcie00: allocate port service Mar 6 16:33:38 maxim-laptop kernel: [ 3.721588] pci_express 0000:00:1c.3:pcie02: allocate port service Mar 6 16:33:38 maxim-laptop kernel: [ 3.721742] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 Mar 6 16:33:38 maxim-laptop kernel: [ 3.722033] vesafb: framebuffer at 0x91000000, mapped to 0xffffc20000080000, using 3072k, total 14336k Mar 6 16:33:38 maxim-laptop kernel: [ 3.722036] vesafb: mode is 1024x768x16, linelength=2048, pages=1 Mar 6 16:33:38 maxim-laptop kernel: [ 3.722038] vesafb: scrolling: redraw Mar 6 16:33:38 maxim-laptop kernel: [ 3.722041] vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0 Mar 6 16:33:38 maxim-laptop kernel: [ 3.750792] Console: switching to colour frame buffer device 128x48 Mar 6 16:33:38 maxim-laptop kernel: [ 3.779408] fb0: VESA VGA frame buffer device Mar 6 16:33:38 maxim-laptop kernel: [ 3.784793] ACPI: AC Adapter [AC] (off-line) Mar 6 16:33:38 maxim-laptop kernel: [ 4.108119] ACPI: Battery Slot [BAT0] (battery present) Mar 6 16:33:38 maxim-laptop kernel: [ 4.108257] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0 Mar 6 16:33:38 maxim-laptop kernel: [ 4.108260] ACPI: Power Button (FF) [PWRF] Mar 6 16:33:38 maxim-laptop kernel: [ 4.108339] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:03/PNP0C0C:00/input/input1 Mar 6 16:33:38 maxim-laptop kernel: [ 4.108342] ACPI: Power Button (CM) [PWRB] Mar 6 16:33:38 maxim-laptop kernel: [ 4.108416] input: Lid Switch as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:03/PNP0C0D:00/input/input2 Mar 6 16:33:38 maxim-laptop kernel: [ 4.108484] ACPI: Lid Switch [LID0] Mar 6 16:33:38 maxim-laptop kernel: [ 4.108556] input: Sleep Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:03/PNP0C0E:00/input/input3 Mar 6 16:33:38 maxim-laptop kernel: [ 4.108559] ACPI: Sleep Button (CM) [SLPB] Mar 6 16:33:38 maxim-laptop kernel: [ 4.216509] acpi device:37: registered as cooling_device0 Mar 6 16:33:38 maxim-laptop kernel: [ 4.216788] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/device:34/device:35/input/input4 Mar 6 16:33:38 maxim-laptop kernel: [ 4.216791] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no) Mar 6 16:33:38 maxim-laptop kernel: [ 4.217349] ACPI: SSDT 7FE74C90, 01EA (r1 PmRef Cpu0Ist 3000 INTL 20051117) Mar 6 16:33:38 maxim-laptop kernel: [ 4.217935] ACPI: SSDT 7FE73610, 05D7 (r1 PmRef Cpu0Cst 3001 INTL 20051117) Mar 6 16:33:38 maxim-laptop kernel: [ 4.220604] Monitor-Mwait will be used to enter C-1 state Mar 6 16:33:38 maxim-laptop kernel: [ 4.220608] Monitor-Mwait will be used to enter C-2 state Mar 6 16:33:38 maxim-laptop kernel: [ 4.220610] Monitor-Mwait will be used to enter C-3 state Mar 6 16:33:38 maxim-laptop kernel: [ 4.220649] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) Mar 6 16:33:38 maxim-laptop kernel: [ 4.220691] processor ACPI_CPU:00: registered as cooling_device1 Mar 6 16:33:38 maxim-laptop kernel: [ 4.220695] ACPI: Processor [CPU0] (supports 8 throttling states) Mar 6 16:33:38 maxim-laptop kernel: [ 4.221100] ACPI: SSDT 7FE74F10, 00C4 (r1 PmRef Cpu1Ist 3000 INTL 20051117) Mar 6 16:33:38 maxim-laptop kernel: [ 4.221548] ACPI: SSDT 7FE76D10, 0083 (r1 PmRef Cpu1Cst 3000 INTL 20051117) Mar 6 16:33:38 maxim-laptop kernel: [ 4.222601] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3]) Mar 6 16:33:38 maxim-laptop kernel: [ 4.222648] processor ACPI_CPU:01: registered as cooling_device2 Mar 6 16:33:38 maxim-laptop kernel: [ 4.222652] ACPI: Processor [CPU1] (supports 8 throttling states) Mar 6 16:33:38 maxim-laptop kernel: [ 4.254501] thermal LNXTHERM:01: registered as thermal_zone0 Mar 6 16:33:38 maxim-laptop kernel: [ 4.266905] ACPI: Thermal Zone [TZ01] (0 C) Mar 6 16:33:38 maxim-laptop kernel: [ 4.449741] Non-volatile memory driver v1.2 Mar 6 16:33:38 maxim-laptop kernel: [ 4.451170] brd: module loaded Mar 6 16:33:38 maxim-laptop kernel: [ 4.451876] loop: module loaded Mar 6 16:33:38 maxim-laptop kernel: [ 4.451994] nbd: registered device at major 43 Mar 6 16:33:38 maxim-laptop kernel: [ 4.453830] Driver 'sd' needs updating - please use bus_type methods Mar 6 16:33:38 maxim-laptop kernel: [ 4.453863] Driver 'sr' needs updating - please use bus_type methods Mar 6 16:33:38 maxim-laptop kernel: [ 4.454223] PNP: PS/2 Controller [PNP0303:KBC0,PNP0f13:MSE0] at 0x60,0x64 irq 1,12 Mar 6 16:33:38 maxim-laptop kernel: [ 4.490077] serio: i8042 KBD port at 0x60,0x64 irq 1 Mar 6 16:33:38 maxim-laptop kernel: [ 4.490082] serio: i8042 AUX port at 0x60,0x64 irq 12 Mar 6 16:33:38 maxim-laptop kernel: [ 4.490247] mice: PS/2 mouse device common for all mice Mar 6 16:33:38 maxim-laptop kernel: [ 4.490280] i2c /dev entries driver Mar 6 16:33:38 maxim-laptop kernel: [ 4.490361] i801_smbus 0000:00:1f.3: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Mar 6 16:33:38 maxim-laptop kernel: [ 4.514870] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5 Mar 6 16:33:38 maxim-laptop kernel: [ 4.568240] cpuidle: using governor ladder Mar 6 16:33:38 maxim-laptop kernel: [ 4.568664] cpuidle: using governor menu Mar 6 16:33:38 maxim-laptop kernel: [ 4.568697] sdhci: Secure Digital Host Controller Interface driver Mar 6 16:33:38 maxim-laptop kernel: [ 4.568699] sdhci: Copyright(c) Pierre Ossman Mar 6 16:33:38 maxim-laptop kernel: [ 4.568716] sdhci-pci 0000:07:00.1: SDHCI controller found [1180:0822] (rev 22) Mar 6 16:33:38 maxim-laptop kernel: [ 4.568733] sdhci-pci 0000:07:00.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22 Mar 6 16:33:38 maxim-laptop kernel: [ 4.568757] Marking TSC unstable due to TSC halts in idle Mar 6 16:33:38 maxim-laptop kernel: [ 4.569835] Registered led device: mmc0 Mar 6 16:33:38 maxim-laptop kernel: [ 4.570894] mmc0: SDHCI controller on PCI [0000:07:00.1] using PIO Mar 6 16:33:38 maxim-laptop kernel: [ 4.570977] Advanced Linux Sound Architecture Driver Version 1.0.18rc3. Mar 6 16:33:38 maxim-laptop kernel: [ 4.570979] ALSA device list: Mar 6 16:33:38 maxim-laptop kernel: [ 4.570980] No soundcards found. Mar 6 16:33:38 maxim-laptop kernel: [ 4.571053] Netfilter messages via NETLINK v0.30. Mar 6 16:33:38 maxim-laptop kernel: [ 4.571486] registered taskstats version 1 Mar 6 16:33:38 maxim-laptop kernel: [ 4.571629] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found Mar 6 16:33:38 maxim-laptop kernel: [ 4.571631] EDD information not available. Mar 6 16:33:38 maxim-laptop kernel: [ 4.571699] Freeing unused kernel memory: 364k freed Mar 6 16:33:38 maxim-laptop kernel: [ 4.715436] fuse init (API version 7.10) Mar 6 16:33:38 maxim-laptop kernel: [ 4.824965] usbcore: registered new interface driver usbfs Mar 6 16:33:38 maxim-laptop kernel: [ 4.824993] usbcore: registered new interface driver hub Mar 6 16:33:38 maxim-laptop kernel: [ 4.829565] usbcore: registered new device driver usb Mar 6 16:33:38 maxim-laptop kernel: [ 4.832046] uhci_hcd: USB Universal Host Controller Interface driver Mar 6 16:33:38 maxim-laptop kernel: [ 4.832095] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832105] uhci_hcd 0000:00:1a.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832110] uhci_hcd 0000:00:1a.0: UHCI Host Controller Mar 6 16:33:38 maxim-laptop kernel: [ 4.832159] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 1 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832205] uhci_hcd 0000:00:1a.0: irq 16, io base 0x000060c0 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832310] usb usb1: configuration #1 chosen from 1 choice Mar 6 16:33:38 maxim-laptop kernel: [ 4.832340] hub 1-0:1.0: USB hub found Mar 6 16:33:38 maxim-laptop kernel: [ 4.832347] hub 1-0:1.0: 2 ports detected Mar 6 16:33:38 maxim-laptop kernel: [ 4.832459] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832467] uhci_hcd 0000:00:1a.1: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832471] uhci_hcd 0000:00:1a.1: UHCI Host Controller Mar 6 16:33:38 maxim-laptop kernel: [ 4.832493] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 2 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832535] uhci_hcd 0000:00:1a.1: irq 21, io base 0x000060a0 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832612] usb usb2: configuration #1 chosen from 1 choice Mar 6 16:33:38 maxim-laptop kernel: [ 4.832641] hub 2-0:1.0: USB hub found Mar 6 16:33:38 maxim-laptop kernel: [ 4.832646] hub 2-0:1.0: 2 ports detected Mar 6 16:33:38 maxim-laptop kernel: [ 4.832740] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832747] uhci_hcd 0000:00:1d.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832751] uhci_hcd 0000:00:1d.0: UHCI Host Controller Mar 6 16:33:38 maxim-laptop kernel: [ 4.832772] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 3 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832809] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00006080 Mar 6 16:33:38 maxim-laptop kernel: [ 4.832888] usb usb3: configuration #1 chosen from 1 choice Mar 6 16:33:38 maxim-laptop kernel: [ 4.832914] hub 3-0:1.0: USB hub found Mar 6 16:33:38 maxim-laptop kernel: [ 4.832920] hub 3-0:1.0: 2 ports detected Mar 6 16:33:38 maxim-laptop kernel: [ 4.833016] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Mar 6 16:33:38 maxim-laptop kernel: [ 4.833023] uhci_hcd 0000:00:1d.1: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 4.833026] uhci_hcd 0000:00:1d.1: UHCI Host Controller Mar 6 16:33:38 maxim-laptop kernel: [ 4.833048] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 4 Mar 6 16:33:38 maxim-laptop kernel: [ 4.833087] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00006060 Mar 6 16:33:38 maxim-laptop kernel: [ 4.833163] usb usb4: configuration #1 chosen from 1 choice Mar 6 16:33:38 maxim-laptop kernel: [ 4.833188] hub 4-0:1.0: USB hub found Mar 6 16:33:38 maxim-laptop kernel: [ 4.833194] hub 4-0:1.0: 2 ports detected Mar 6 16:33:38 maxim-laptop kernel: [ 4.833288] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Mar 6 16:33:38 maxim-laptop kernel: [ 4.833295] uhci_hcd 0000:00:1d.2: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 4.833298] uhci_hcd 0000:00:1d.2: UHCI Host Controller Mar 6 16:33:38 maxim-laptop kernel: [ 4.833320] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 5 Mar 6 16:33:38 maxim-laptop kernel: [ 4.833355] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00006040 Mar 6 16:33:38 maxim-laptop kernel: [ 4.833433] usb usb5: configuration #1 chosen from 1 choice Mar 6 16:33:38 maxim-laptop kernel: [ 4.833458] hub 5-0:1.0: USB hub found Mar 6 16:33:38 maxim-laptop kernel: [ 4.833464] hub 5-0:1.0: 2 ports detected Mar 6 16:33:38 maxim-laptop kernel: [ 4.971115] ohci1394 0000:07:00.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20 Mar 6 16:33:38 maxim-laptop kernel: [ 4.971123] ohci1394 0000:07:00.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 4.984218] tg3.c:v3.94 (August 14, 2008) Mar 6 16:33:38 maxim-laptop kernel: [ 4.984279] tg3 0000:05:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Mar 6 16:33:38 maxim-laptop kernel: [ 4.984294] tg3 0000:05:00.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 4.995912] libata version 3.00 loaded. Mar 6 16:33:38 maxim-laptop kernel: [ 4.998672] ata_piix 0000:00:1f.1: version 2.12 Mar 6 16:33:38 maxim-laptop kernel: [ 4.998683] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18 Mar 6 16:33:38 maxim-laptop kernel: [ 4.998725] ata_piix 0000:00:1f.1: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 5.023914] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[20] MMIO=[97000000-970007ff] Max Packet=[2048] IR/IT contexts=[4/4] Mar 6 16:33:38 maxim-laptop kernel: [ 5.031356] eth0: Tigon3 [partno(BCM95787m) rev b002 PHY(5787)] (PCI Express) 10/100/1000Base-T Ethernet 00:1b:38:c8:50:f3 Mar 6 16:33:38 maxim-laptop kernel: [ 5.031360] eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] WireSpeed[1] TSOcap[1] Mar 6 16:33:38 maxim-laptop kernel: [ 5.031363] eth0: dma_rwctrl[76180000] dma_mask[64-bit] Mar 6 16:33:38 maxim-laptop kernel: [ 5.031560] scsi0 : ata_piix Mar 6 16:33:38 maxim-laptop kernel: [ 5.031998] scsi1 : ata_piix Mar 6 16:33:38 maxim-laptop kernel: [ 5.032039] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x60e0 irq 14 Mar 6 16:33:38 maxim-laptop kernel: [ 5.032042] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x60e8 irq 15 Mar 6 16:33:38 maxim-laptop kernel: [ 5.144170] usb 4-2: new full speed USB device using uhci_hcd and address 2 Mar 6 16:33:38 maxim-laptop kernel: [ 5.196554] ata1.00: ATAPI: HL-DT-ST DVDRAM GSA-T20N, WP03, max UDMA/33 Mar 6 16:33:38 maxim-laptop kernel: [ 5.212484] ata1.00: configured for UDMA/33 Mar 6 16:33:38 maxim-laptop kernel: [ 5.339279] usb 4-2: configuration #1 chosen from 1 choice Mar 6 16:33:38 maxim-laptop kernel: [ 5.405151] isa bounce pool size: 16 pages Mar 6 16:33:38 maxim-laptop kernel: [ 5.408875] scsi 0:0:0:0: CD-ROM HL-DT-ST DVDRAM GSA-T20N WP03 PQ: 0 ANSI: 5 Mar 6 16:33:38 maxim-laptop kernel: [ 5.420801] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray Mar 6 16:33:38 maxim-laptop kernel: [ 5.420807] Uniform CD-ROM driver Revision: 3.20 Mar 6 16:33:38 maxim-laptop kernel: [ 5.420962] sr 0:0:0:0: Attached scsi CD-ROM sr0 Mar 6 16:33:38 maxim-laptop kernel: [ 5.421054] sr 0:0:0:0: Attached scsi generic sg0 type 5 Mar 6 16:33:38 maxim-laptop kernel: [ 5.421207] ahci 0000:00:1f.2: version 3.0 Mar 6 16:33:38 maxim-laptop kernel: [ 5.421223] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 Mar 6 16:33:38 maxim-laptop kernel: [ 5.421290] ahci 0000:00:1f.2: irq 506 for MSI/MSI-X Mar 6 16:33:38 maxim-laptop kernel: [ 5.421369] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 3 ports 3 Gbps 0x7 impl SATA mode Mar 6 16:33:38 maxim-laptop kernel: [ 5.421373] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems Mar 6 16:33:38 maxim-laptop kernel: [ 5.421379] ahci 0000:00:1f.2: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 5.422589] scsi2 : ahci Mar 6 16:33:38 maxim-laptop kernel: [ 5.422678] scsi3 : ahci Mar 6 16:33:38 maxim-laptop kernel: [ 5.423635] scsi4 : ahci Mar 6 16:33:38 maxim-laptop kernel: [ 5.423690] ata3: SATA max UDMA/133 abar m2048@0x9b304000 port 0x9b304100 irq 506 Mar 6 16:33:38 maxim-laptop kernel: [ 5.423694] ata4: SATA max UDMA/133 abar m2048@0x9b304000 port 0x9b304180 irq 506 Mar 6 16:33:38 maxim-laptop kernel: [ 5.423697] ata5: SATA max UDMA/133 abar m2048@0x9b304000 port 0x9b304200 irq 506 Mar 6 16:33:38 maxim-laptop kernel: [ 5.504099] Clocksource tsc unstable (delta = -230857709 ns) Mar 6 16:33:38 maxim-laptop kernel: [ 6.080154] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) Mar 6 16:33:38 maxim-laptop kernel: [ 6.305633] ieee1394: Host added: ID:BUS[0-00:1023] GUID[b64057b700023f7c] Mar 6 16:33:38 maxim-laptop kernel: [ 6.464933] ata3.00: ATA-8: TOSHIBA MK1646GSX, LB113J, max UDMA/100 Mar 6 16:33:38 maxim-laptop kernel: [ 6.464939] ata3.00: 312581808 sectors, multi 16: LBA48 NCQ (depth 31/32) Mar 6 16:33:38 maxim-laptop kernel: [ 6.465896] ata3.00: configured for UDMA/100 Mar 6 16:33:38 maxim-laptop kernel: [ 6.801120] ata4: SATA link down (SStatus 0 SControl 300) Mar 6 16:33:38 maxim-laptop kernel: [ 7.152126] ata5: SATA link down (SStatus 0 SControl 300) Mar 6 16:33:38 maxim-laptop kernel: [ 7.185234] scsi 2:0:0:0: Direct-Access ATA TOSHIBA MK1646GS LB11 PQ: 0 ANSI: 5 Mar 6 16:33:38 maxim-laptop kernel: [ 7.185829] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) Mar 6 16:33:38 maxim-laptop kernel: [ 7.185845] sd 2:0:0:0: [sda] Write Protect is off Mar 6 16:33:38 maxim-laptop kernel: [ 7.185848] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 Mar 6 16:33:38 maxim-laptop kernel: [ 7.185872] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 6 16:33:38 maxim-laptop kernel: [ 7.185946] sd 2:0:0:0: [sda] 312581808 512-byte hardware sectors: (160 GB/149 GiB) Mar 6 16:33:38 maxim-laptop kernel: [ 7.185961] sd 2:0:0:0: [sda] Write Protect is off Mar 6 16:33:38 maxim-laptop kernel: [ 7.185963] sd 2:0:0:0: [sda] Mode Sense: 00 3a 00 00 Mar 6 16:33:38 maxim-laptop kernel: [ 7.185987] sd 2:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA Mar 6 16:33:38 maxim-laptop kernel: [ 7.185990] sda: sda1 sda3 sda4 Mar 6 16:33:38 maxim-laptop kernel: [ 7.275930] sd 2:0:0:0: [sda] Attached SCSI disk Mar 6 16:33:38 maxim-laptop kernel: [ 7.275991] sd 2:0:0:0: Attached scsi generic sg1 type 0 Mar 6 16:33:38 maxim-laptop kernel: [ 7.491870] PM: Starting manual resume from disk Mar 6 16:33:38 maxim-laptop kernel: [ 7.541160] EXT3-fs: mounted filesystem with ordered data mode. Mar 6 16:33:38 maxim-laptop kernel: [ 7.541242] kjournald starting. Commit interval 5 seconds Mar 6 16:33:38 maxim-laptop kernel: [ 13.960909] udevd version 124 started Mar 6 16:33:38 maxim-laptop kernel: [ 14.467309] iTCO_vendor_support: vendor-support=0 Mar 6 16:33:38 maxim-laptop kernel: [ 15.016021] nvidia: module license 'NVIDIA' taints kernel. Mar 6 16:33:38 maxim-laptop kernel: [ 15.111888] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.04 Mar 6 16:33:38 maxim-laptop kernel: [ 15.112167] iTCO_wdt: Found a ICH8M TCO device (Version=2, TCOBASE=0x0460) Mar 6 16:33:38 maxim-laptop kernel: [ 15.112246] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0) Mar 6 16:33:38 maxim-laptop kernel: [ 15.288918] nvidia 0000:01:00.0: power state changed by ACPI to D0 Mar 6 16:33:38 maxim-laptop kernel: [ 15.288931] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 Mar 6 16:33:38 maxim-laptop kernel: [ 15.288940] nvidia 0000:01:00.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 15.289158] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 177.82 Tue Nov 4 16:50:05 PST 2008 Mar 6 16:33:38 maxim-laptop kernel: [ 15.576187] cfg80211: Using static regulatory domain info Mar 6 16:33:38 maxim-laptop kernel: [ 15.576192] cfg80211: Regulatory domain: US Mar 6 16:33:38 maxim-laptop kernel: [ 15.576195] ^I(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Mar 6 16:33:38 maxim-laptop kernel: [ 15.576199] ^I(2402000 KHz - 2472000 KHz @ 40000 KHz), (600 mBi, 2700 mBm) Mar 6 16:33:38 maxim-laptop kernel: [ 15.576204] ^I(5170000 KHz - 5190000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Mar 6 16:33:38 maxim-laptop kernel: [ 15.576207] ^I(5190000 KHz - 5210000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Mar 6 16:33:38 maxim-laptop kernel: [ 15.576211] ^I(5210000 KHz - 5230000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Mar 6 16:33:38 maxim-laptop kernel: [ 15.576215] ^I(5230000 KHz - 5330000 KHz @ 40000 KHz), (600 mBi, 2300 mBm) Mar 6 16:33:38 maxim-laptop kernel: [ 15.576219] ^I(5735000 KHz - 5835000 KHz @ 40000 KHz), (600 mBi, 3000 mBm) Mar 6 16:33:38 maxim-laptop kernel: [ 15.576230] cfg80211: Calling CRDA for country: IL Mar 6 16:33:38 maxim-laptop kernel: [ 15.860178] cfg80211: Regulatory domain changed to country: IL Mar 6 16:33:38 maxim-laptop kernel: [ 15.860182] ^I(start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Mar 6 16:33:38 maxim-laptop kernel: [ 15.860185] ^I(2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm) Mar 6 16:33:38 maxim-laptop kernel: [ 15.912667] lib80211: common routines for IEEE802.11 drivers Mar 6 16:33:38 maxim-laptop kernel: [ 15.912671] lib80211_crypt: registered algorithm 'NULL' Mar 6 16:33:38 maxim-laptop kernel: [ 15.997653] Linux video capture interface: v2.00 Mar 6 16:33:38 maxim-laptop kernel: [ 16.413708] uvcvideo: Found UVC 1.00 device Acer CrystalEye webcam (064e:a101) Mar 6 16:33:38 maxim-laptop kernel: [ 16.417304] usbcore: registered new interface driver uvcvideo Mar 6 16:33:38 maxim-laptop kernel: [ 16.417308] USB Video Class driver (v0.1.0) Mar 6 16:33:38 maxim-laptop kernel: [ 16.489551] input: PS/2 Mouse as /devices/platform/i8042/serio1/input/input6 Mar 6 16:33:38 maxim-laptop kernel: [ 16.533255] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22 Mar 6 16:33:38 maxim-laptop kernel: [ 16.533485] HDA Intel 0000:00:1b.0: irq 505 for MSI/MSI-X Mar 6 16:33:38 maxim-laptop kernel: [ 16.533533] HDA Intel 0000:00:1b.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 16.581456] input: AlpsPS/2 ALPS GlidePoint as /devices/platform/i8042/serio1/input/input7 Mar 6 16:33:38 maxim-laptop kernel: [ 17.040031] iwl3945: Intel(R) PRO/Wireless 3945ABG/BG Network Connection driver for Linux, 1.2.26kds Mar 6 16:33:38 maxim-laptop kernel: [ 17.040036] iwl3945: Copyright(c) 2003-2009 Intel Corporation Mar 6 16:33:38 maxim-laptop kernel: [ 17.040144] iwl3945 0000:06:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 Mar 6 16:33:38 maxim-laptop kernel: [ 17.040161] iwl3945 0000:06:00.0: setting latency timer to 64 Mar 6 16:33:38 maxim-laptop kernel: [ 17.093063] iwl3945 0000:06:00.0: Tunable channels: 13 802.11bg, 0 802.11a channels Mar 6 16:33:38 maxim-laptop kernel: [ 17.093066] iwl3945 0000:06:00.0: Detected Intel Wireless WiFi Link 3945BG Mar 6 16:33:38 maxim-laptop kernel: [ 17.093197] iwl3945 0000:06:00.0: irq 504 for MSI/MSI-X Mar 6 16:33:38 maxim-laptop kernel: [ 17.093829] phy0: Selected rate control algorithm 'iwl-3945-rs' Mar 6 16:33:38 maxim-laptop kernel: [ 17.528850] rtc_cmos 00:03: RTC can wake from S4 Mar 6 16:33:38 maxim-laptop kernel: [ 17.528913] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 Mar 6 16:33:38 maxim-laptop kernel: [ 17.528950] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs Mar 6 16:33:38 maxim-laptop kernel: [ 17.688397] Adding 3068404k swap on /dev/sda3. Priority:-1 extents:1 across:3068404k Mar 6 16:33:38 maxim-laptop kernel: [ 17.720510] EXT3 FS on sda4, internal journal Mar 6 16:33:38 maxim-laptop kernel: [ 18.630194] ip_tables: (C) 2000-2006 Netfilter Core Team Mar 6 16:33:38 maxim-laptop kernel: [ 19.332081] RPC: Registered udp transport module. Mar 6 16:33:38 maxim-laptop kernel: [ 19.332085] RPC: Registered tcp transport module. Mar 6 16:33:38 maxim-laptop kernel: [ 21.928938] warning: `avahi-daemon' uses 32-bit capabilities (legacy support in use) Mar 6 16:33:39 maxim-laptop kernel: [ 22.503557] NET: Registered protocol family 10 Mar 6 16:33:39 maxim-laptop kernel: [ 22.504500] lo: Disabled Privacy Extensions Mar 6 16:33:44 maxim-laptop kernel: [ 27.681023] Installing knfsd (copyright (C) 1996 [email protected]). Mar 6 16:33:44 maxim-laptop kernel: [ 27.767775] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory Mar 6 16:33:44 maxim-laptop kernel: [ 27.781174] NFSD: starting 90-second grace period Mar 6 16:33:45 maxim-laptop kernel: [ 28.780330] vboxdrv: Trying to deactivate the NMI watchdog permanently... Mar 6 16:33:45 maxim-laptop kernel: [ 28.780335] vboxdrv: Successfully done. Mar 6 16:33:45 maxim-laptop kernel: [ 28.780338] vboxdrv: Found 2 processor cores. Mar 6 16:33:45 maxim-laptop kernel: [ 28.780873] VBoxDrv: dbg - g_abExecMemory=ffffffffa0bb2a60 Mar 6 16:33:45 maxim-laptop kernel: [ 28.780906] vboxdrv: fAsync=0 offMin=0x2bc offMax=0x184c Mar 6 16:33:45 maxim-laptop kernel: [ 28.782378] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'. Mar 6 16:33:45 maxim-laptop kernel: [ 28.782382] vboxdrv: Successfully loaded version 2.1.4 (interface 0x000a0009). Mar 6 16:33:45 maxim-laptop kernel: [ 28.996118] VBoxNetFlt: dbg - g_abExecMemory=ffffffffa0d4f940 Mar 6 16:33:46 maxim-laptop kernel: [ 29.776085] PPP generic driver version 2.4.2 Mar 6 16:33:46 maxim-laptop kernel: [ 29.789326] NET: Registered protocol family 24 Mar 6 16:33:53 maxim-laptop kernel: [ 36.002376] tg3 0000:05:00.0: irq 503 for MSI/MSI-X Mar 6 16:33:53 maxim-laptop kernel: [ 36.207713] ADDRCONF(NETDEV_UP): eth0: link is not ready Mar 6 16:33:53 maxim-laptop kernel: [ 36.240987] iwl3945 0000:06:00.0: firmware: requesting iwlwifi-3945-2.ucode Mar 6 16:33:53 maxim-laptop kernel: [ 36.352725] iwl3945 0000:06:00.0: loaded firmware version 15.28.2.8 Mar 6 16:33:53 maxim-laptop kernel: [ 36.400240] Registered led device: iwl-phy0::radio Mar 6 16:33:53 maxim-laptop kernel: [ 36.400260] Registered led device: iwl-phy0::assoc Mar 6 16:33:53 maxim-laptop kernel: [ 36.400277] Registered led device: iwl-phy0::RX Mar 6 16:33:53 maxim-laptop kernel: [ 36.400293] Registered led device: iwl-phy0::TX Mar 6 16:33:53 maxim-laptop kernel: [ 36.433905] ADDRCONF(NETDEV_UP): wlan0: link is not ready Mar 6 16:33:53 maxim-laptop kernel: [ 36.513802] NET: Registered protocol family 17 Mar 6 16:33:54 maxim-laptop kernel: [ 37.809511] wlan0: direct probe to AP ffff88007e5279e0 try 1 Mar 6 16:33:55 maxim-laptop kernel: [ 38.009144] wlan0: direct probe to AP ffff88007e5279e0 try 2 Mar 6 16:33:55 maxim-laptop kernel: [ 38.209058] wlan0: direct probe to AP ffff88007e5279e0 try 3 Mar 6 16:33:55 maxim-laptop kernel: [ 38.409055] wlan0: direct probe to AP ffff88007e5279e0 timed out Mar 6 16:33:59 maxim-laptop kernel: [ 42.732223] wlan0: authenticate with AP ffff88007e5279e0 Mar 6 16:33:59 maxim-laptop kernel: [ 42.734140] wlan0: authenticated Mar 6 16:33:59 maxim-laptop kernel: [ 42.734143] wlan0: associate with AP ffff88007e5279e0 Mar 6 16:33:59 maxim-laptop kernel: [ 42.736717] wlan0: RX AssocResp from ffff88007d796026 (capab=0x411 status=0 aid=1) Mar 6 16:33:59 maxim-laptop kernel: [ 42.736721] wlan0: associated Mar 6 16:33:59 maxim-laptop kernel: [ 42.740743] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready Mar 6 16:34:09 maxim-laptop kernel: [ 52.929122] wlan0: no IPv6 routers present Mar 6 16:36:27 maxim-laptop kernel: [ 190.649425] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Mar 6 16:36:27 maxim-laptop kernel: [ 190.649430] Warning! ehci_hcd should always be loaded before uhci_hcd and ohci_hcd, not after Mar 6 16:36:27 maxim-laptop kernel: [ 190.649474] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 Mar 6 16:36:27 maxim-laptop kernel: [ 190.649549] ehci_hcd 0000:00:1a.7: setting latency timer to 64 Mar 6 16:36:27 maxim-laptop kernel: [ 190.649555] ehci_hcd 0000:00:1a.7: EHCI Host Controller Mar 6 16:36:27 maxim-laptop kernel: [ 190.649617] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 6 Mar 6 16:36:27 maxim-laptop kernel: [ 190.653540] ehci_hcd 0000:00:1a.7: debug port 1 Mar 6 16:36:27 maxim-laptop kernel: [ 190.653550] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported Mar 6 16:36:27 maxim-laptop kernel: [ 190.653563] ehci_hcd 0000:00:1a.7: irq 18, io mem 0x9b304c00 Mar 6 16:36:27 maxim-laptop kernel: [ 190.668139] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00 Mar 6 16:36:27 maxim-laptop kernel: [ 190.668307] usb usb6: configuration #1 chosen from 1 choice Mar 6 16:36:27 maxim-laptop kernel: [ 190.668366] hub 6-0:1.0: USB hub found Mar 6 16:36:27 maxim-laptop kernel: [ 190.668379] hub 6-0:1.0: 4 ports detected Mar 6 16:36:27 maxim-laptop kernel: [ 190.668610] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23 Mar 6 16:36:27 maxim-laptop kernel: [ 190.668660] ehci_hcd 0000:00:1d.7: setting latency timer to 64 Mar 6 16:36:27 maxim-laptop kernel: [ 190.668666] ehci_hcd 0000:00:1d.7: EHCI Host Controller Mar 6 16:36:27 maxim-laptop kernel: [ 190.668723] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 7 Mar 6 16:36:27 maxim-laptop kernel: [ 190.672657] ehci_hcd 0000:00:1d.7: debug port 1 Mar 6 16:36:27 maxim-laptop kernel: [ 190.672668] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported Mar 6 16:36:27 maxim-laptop kernel: [ 190.672681] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x9b304800 Mar 6 16:36:27 maxim-laptop kernel: [ 190.688094] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00 Mar 6 16:36:27 maxim-laptop kernel: [ 190.688260] usb usb7: configuration #1 chosen from 1 choice Mar 6 16:36:27 maxim-laptop kernel: [ 190.688317] hub 7-0:1.0: USB hub found Mar 6 16:36:27 maxim-laptop kernel: [ 190.688332] hub 7-0:1.0: 6 ports detected Mar 6 16:36:27 maxim-laptop kernel: [ 190.853198] usb 4-2: USB disconnect, address 2 Mar 6 16:36:28 maxim-laptop kernel: [ 191.000139] usb 7-4: new high speed USB device using ehci_hcd and address 2 Mar 6 16:36:28 maxim-laptop kernel: [ 191.142098] usb 7-4: configuration #1 chosen from 1 choice Mar 6 16:36:28 maxim-laptop kernel: [ 191.142481] uvcvideo: Found UVC 1.00 device Acer CrystalEye webcam (064e:a101) Mar 6 16:37:03 maxim-laptop kernel: [ 226.743967] wlan0 direct probe responded Mar 6 16:37:03 maxim-laptop kernel: [ 226.743974] wlan0: authenticate with AP ffff88007e5279e0 Mar 6 16:37:03 maxim-laptop kernel: [ 226.746028] wlan0: authenticated Mar 6 16:37:03 maxim-laptop kernel: [ 226.746034] wlan0: associate with AP ffff88007e5279e0 Mar 6 16:37:03 maxim-laptop kernel: [ 226.748845] wlan0: RX ReassocResp from ffff88007a40d026 (capab=0x411 status=0 aid=1) Mar 6 16:37:03 maxim-laptop kernel: [ 226.748850] wlan0: associated Mar 6 16:37:11 maxim-laptop kernel: [ 234.713048] wlan0: deauthenticated (Reason: 15) Mar 6 16:37:12 maxim-laptop kernel: [ 235.712175] wlan0: direct probe to AP ffff88007e5279e0 try 1 Mar 6 16:37:12 maxim-laptop kernel: [ 235.715773] wlan0 direct probe responded Mar 6 16:37:12 maxim-laptop kernel: [ 235.715780] wlan0: authenticate with AP ffff88007e5279e0 Mar 6 16:37:12 maxim-laptop kernel: [ 235.717766] wlan0: authenticated Mar 6 16:37:12 maxim-laptop kernel: [ 235.717771] wlan0: associate with AP ffff88007e5279e0 Mar 6 16:37:12 maxim-laptop kernel: [ 235.720505] wlan0: RX ReassocResp from ffff880079c1f026 (capab=0x411 status=0 aid=1) Mar 6 16:37:12 maxim-laptop kernel: [ 235.720511] wlan0: associated Mar 6 16:41:16 maxim-laptop kernel: [ 479.937151] CE: hpet increasing min_delta_ns to 15000 nsec Mar 6 16:42:11 maxim-laptop kernel: [ 534.690940] rtc_cmos 00:03: RTC can wake from S4 Mar 6 16:42:11 maxim-laptop kernel: [ 534.691033] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0 Mar 6 16:42:11 maxim-laptop kernel: [ 534.691081] rtc0: alarms up to one month, 242 bytes nvram, hpet irqs Mar 6 16:46:52 maxim-laptop kernel: [ 815.904148] usb 7-1: new high speed USB device using ehci_hcd and address 3 Mar 6 16:46:53 maxim-laptop kernel: [ 816.057348] usb 7-1: configuration #1 chosen from 1 choice Mar 6 16:50:55 maxim-laptop kernel: [ 1058.786475] usb 7-1: USB disconnect, address 3 Mar 6 16:50:56 maxim-laptop kernel: [ 1059.376175] usb 7-1: new high speed USB device using ehci_hcd and address 4 Mar 6 16:50:56 maxim-laptop kernel: [ 1059.529573] usb 7-1: configuration #1 chosen from 1 choice Mar 6 16:51:06 maxim-laptop kernel: [ 1069.232848] usb 7-1: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110 Mar 6 16:51:11 maxim-laptop kernel: [ 1074.232244] usb 7-1: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110 Mar 6 16:51:38 maxim-laptop kernel: [ 1101.032089] CE: hpet increasing min_delta_ns to 22500 nsec Mar 6 16:51:56 maxim-laptop kernel: [ 1119.325061] uhci_hcd 0000:00:1d.2: remove, state 4 Mar 6 16:51:56 maxim-laptop kernel: [ 1119.325076] usb usb5: USB disconnect, address 1 Mar 6 16:51:56 maxim-laptop kernel: [ 1119.325605] uhci_hcd 0000:00:1d.2: USB bus 5 deregistered Mar 6 16:51:56 maxim-laptop kernel: [ 1119.325680] uhci_hcd 0000:00:1d.2: PCI INT C disabled Mar 6 16:51:56 maxim-laptop kernel: [ 1119.325698] uhci_hcd 0000:00:1d.1: remove, state 4 Mar 6 16:51:56 maxim-laptop kernel: [ 1119.325709] usb usb4: USB disconnect, address 1 Mar 6 16:51:56 maxim-laptop kernel: [ 1119.326163] uhci_hcd 0000:00:1d.1: USB bus 4 deregistered Mar 6 16:51:56 maxim-laptop kernel: [ 1119.326226] uhci_hcd 0000:00:1d.1: PCI INT B disabled Mar 6 16:51:56 maxim-laptop kernel: [ 1119.326242] uhci_hcd 0000:00:1d.0: remove, state 4 Mar 6 16:51:56 maxim-laptop kernel: [ 1119.326252] usb usb3: USB disconnect, address 1 Mar 6 16:51:56 maxim-laptop kernel: [ 1119.326700] uhci_hcd 0000:00:1d.0: USB bus 3 deregistered Mar 6 16:51:56 maxim-laptop kernel: [ 1119.326764] uhci_hcd 0000:00:1d.0: PCI INT A disabled Mar 6 16:51:56 maxim-laptop kernel: [ 1119.326781] uhci_hcd 0000:00:1a.1: remove, state 4 Mar 6 16:51:56 maxim-laptop kernel: [ 1119.326791] usb usb2: USB disconnect, address 1 Mar 6 16:51:56 maxim-laptop kernel: [ 1119.327238] uhci_hcd 0000:00:1a.1: USB bus 2 deregistered Mar 6 16:51:56 maxim-laptop kernel: [ 1119.327300] uhci_hcd 0000:00:1a.1: PCI INT B disabled Mar 6 16:51:56 maxim-laptop kernel: [ 1119.327316] uhci_hcd 0000:00:1a.0: remove, state 4 Mar 6 16:51:56 maxim-laptop kernel: [ 1119.327327] usb usb1: USB disconnect, address 1 Mar 6 16:51:56 maxim-laptop kernel: [ 1119.327768] uhci_hcd 0000:00:1a.0: USB bus 1 deregistered Mar 6 16:51:56 maxim-laptop kernel: [ 1119.327832] uhci_hcd 0000:00:1a.0: PCI INT A disabled Mar 6 16:52:03 maxim-laptop kernel: [ 1126.619487] usb 7-1: USB disconnect, address 4 Mar 6 16:52:04 maxim-laptop kernel: [ 1127.616172] usb 7-1: new high speed USB device using ehci_hcd and address 5 Mar 6 16:52:04 maxim-laptop kernel: [ 1127.771058] usb 7-1: configuration #1 chosen from 1 choice Mar 6 16:52:29 maxim-laptop kernel: [ 1152.198365] usb 7-1: USB disconnect, address 5 Mar 6 16:52:29 maxim-laptop kernel: [ 1152.596149] usb 7-1: new high speed USB device using ehci_hcd and address 6 Mar 6 16:52:29 maxim-laptop kernel: [ 1152.748970] usb 7-1: configuration #1 chosen from 1 choice Mar 6 16:52:44 maxim-laptop kernel: [ 1167.996484] usb 7-1: USB disconnect, address 6 Mar 6 16:52:45 maxim-laptop kernel: [ 1168.548155] usb 7-1: new high speed USB device using ehci_hcd and address 7 Mar 6 16:52:45 maxim-laptop kernel: [ 1168.700543] usb 7-1: configuration #1 chosen from 1 choice Mar 6 16:54:16 maxim-laptop kernel: [ 1259.420501] usb 7-1: USB disconnect, address 7 Mar 6 16:54:16 maxim-laptop kernel: [ 1259.700124] usb 7-1: new high speed USB device using ehci_hcd and address 8 Mar 6 16:54:16 maxim-laptop kernel: [ 1259.756487] hub 7-0:1.0: unable to enumerate USB device on port 1 Mar 6 16:54:19 maxim-laptop kernel: [ 1262.892156] usb 7-3: new high speed USB device using ehci_hcd and address 9 Mar 6 16:54:20 maxim-laptop kernel: [ 1263.026579] usb 7-3: configuration #1 chosen from 1 choice Mar 6 16:55:07 maxim-laptop kernel: [ 1310.474257] usb 7-3: USB disconnect, address 9 Mar 6 16:55:08 maxim-laptop kernel: [ 1311.121146] usb 7-3: new high speed USB device using ehci_hcd and address 10 Mar 6 16:55:08 maxim-laptop kernel: [ 1311.280236] usb 7-3: configuration #1 chosen from 1 choice Mar 6 16:55:19 maxim-laptop kernel: [ 1322.552349] usb 7-3: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -110 Mar 6 16:55:42 maxim-laptop kernel: [ 1345.814010] usb 7-3: USB disconnect, address 10 Mar 6 16:55:43 maxim-laptop kernel: [ 1346.512173] usb 7-3: new high speed USB device using ehci_hcd and address 11 Mar 6 16:55:43 maxim-laptop kernel: [ 1346.665365] usb 7-3: configuration #1 chosen from 1 choice Mar 6 16:55:58 maxim-laptop kernel: [ 1361.029946] usb 7-3: USB disconnect, address 11 Mar 6 16:56:00 maxim-laptop kernel: [ 1363.456146] usb 7-1: new high speed USB device using ehci_hcd and address 12 Mar 6 16:56:00 maxim-laptop kernel: [ 1363.590716] usb 7-1: configuration #1 chosen from 1 choice Mar 6 16:56:16 maxim-laptop kernel: [ 1379.130534] usb 7-1: USB disconnect, address 12 Mar 6 16:56:23 maxim-laptop kernel: [ 1386.464154] usb 7-5: new high speed USB device using ehci_hcd and address 13 Mar 6 16:56:23 maxim-laptop kernel: [ 1386.598718] usb 7-5: configuration #1 chosen from 1 choice Mar 6 16:56:37 maxim-laptop kernel: [ 1400.435025] usb 7-5: USB disconnect, address 13 Mar 6 16:56:39 maxim-laptop kernel: [ 1402.448152] usb 6-1: new high speed USB device using ehci_hcd and address 2 Mar 6 16:56:39 maxim-laptop kernel: [ 1402.583548] usb 6-1: configuration #1 chosen from 1 choice Mar 6 16:56:41 maxim-laptop kernel: [ 1404.056340] usb 6-1: usbfs: USBDEVFS_CONTROL failed cmd python rqt 128 rq 6 len 255 ret -71 Mar 6 16:57:26 maxim-laptop kernel: [ 1449.953092] usb 6-1: USB disconnect, address 2 Mar 6 16:57:28 maxim-laptop kernel: [ 1451.460154] usb 6-1: new high speed USB device using ehci_hcd and address 3 Mar 6 16:57:28 maxim-laptop kernel: [ 1451.594646] usb 6-1: configuration #1 chosen from 1 choice Mar 6 16:57:44 maxim-laptop kernel: [ 1467.267565] usb 6-1: USB disconnect, address 3 Mar 6 16:57:50 maxim-laptop kernel: [ 1473.932155] usb 7-1: new high speed USB device using ehci_hcd and address 14 Mar 6 16:57:51 maxim-laptop kernel: [ 1474.066621] usb 7-1: configuration #1 chosen from 1 choice Mar 6 16:58:05 maxim-laptop kernel: [ 1488.840655] usb 7-1: USB disconnect, address 14 Mar 6 16:58:06 maxim-laptop kernel: [ 1489.249038] usb 7-1: new high speed USB device using ehci_hcd and address 15 Mar 6 16:58:06 maxim-laptop kernel: [ 1489.400881] usb 7-1: configuration #1 chosen from 1 choice Mar 6 16:59:41 maxim-laptop kernel: [ 1584.673540] usb 7-1: USB disconnect, address 15 Mar 6 16:59:42 maxim-laptop kernel: [ 1585.668162] usb 7-1: new high speed USB device using ehci_hcd and address 16 Mar 6 16:59:42 maxim-laptop kernel: [ 1585.821943] usb 7-1: configuration #1 chosen from 1 choice Mar 6 17:00:07 maxim-laptop kernel: [ 1610.726543] usb 7-1: USB disconnect, address 16 Mar 6 17:00:10 maxim-laptop kernel: [ 1613.264068] usb 7-3: new high speed USB device using ehci_hcd and address 17 Mar 6 17:00:10 maxim-laptop kernel: [ 1613.398995] usb 7-3: configuration #1 chosen from 1 choice Mar 6 17:00:27 maxim-laptop kernel: [ 1630.239794] usb 7-3: USB disconnect, address 17 Mar 6 17:00:27 maxim-laptop kernel: [ 1630.804066] usb 7-3: new high speed USB device using ehci_hcd and address 18 Mar 6 17:00:27 maxim-laptop kernel: [ 1630.957783] usb 7-3: configuration #1 chosen from 1 choice Mar 6 17:01:23 maxim-laptop kernel: [ 1686.602599] usb 7-3: USB disconnect, address 18 Mar 6 17:01:28 maxim-laptop kernel: [ 1691.276159] usb 6-1: new high speed USB device using ehci_hcd and address 4 Mar 6 17:01:28 maxim-laptop kernel: [ 1691.413080] usb 6-1: configuration #1 chosen from 1 choice Mar 6 17:01:51 maxim-laptop kernel: [ 1714.267598] usb 6-1: USB disconnect, address 4 Mar 6 17:01:56 maxim-laptop kernel: [ 1719.070083] usb 7-1: new high speed USB device using ehci_hcd and address 19 Mar 6 17:01:56 maxim-laptop kernel: [ 1719.202797] usb 7-1: configuration #1 chosen from 1 choice Mar 6 17:02:46 maxim-laptop kernel: [ 1769.996433] usb 7-1: USB disconnect, address 19 Mar 6 17:02:47 maxim-laptop kernel: [ 1770.680184] usb 7-1: new high speed USB device using ehci_hcd and address 20 Mar 6 17:02:47 maxim-laptop kernel: [ 1770.833470] usb 7-1: configuration #1 chosen from 1 choice Mar 6 17:03:41 maxim-laptop kernel: [ 1824.788197] usb 7-1: USB disconnect, address 20 Mar 6 17:03:44 maxim-laptop kernel: [ 1827.752144] usb 7-1: new high speed USB device using ehci_hcd and address 21 Mar 6 17:03:44 maxim-laptop kernel: [ 1827.886664] usb 7-1: configuration #1 chosen from 1 choice Mar 6 17:04:54 maxim-laptop kernel: [ 1897.700139] iwl3945 0000:06:00.0: Error sending REPLY_RXON: time out after 500ms. Mar 6 17:04:54 maxim-laptop kernel: [ 1897.700147] iwl3945 0000:06:00.0: Error clearing ASSOC_MSK on current configuration (-110). Mar 6 17:05:19 maxim-laptop kernel: [ 1922.349512] wlan0: direct probe to AP ffff88007e5279e0 try 1 Mar 6 17:05:19 maxim-laptop kernel: [ 1922.354292] wlan0 direct probe responded Mar 6 17:05:19 maxim-laptop kernel: [ 1922.354298] wlan0: authenticate with AP ffff88007e5279e0 Mar 6 17:05:19 maxim-laptop kernel: [ 1922.369028] wlan0: authenticated Mar 6 17:05:19 maxim-laptop kernel: [ 1922.369035] wlan0: associate with AP ffff88007e5279e0 Mar 6 17:05:19 maxim-laptop kernel: [ 1922.371321] wlan0: RX AssocResp from ffff88007c0c5026 (capab=0x411 status=0 aid=1) Mar 6 17:05:19 maxim-laptop kernel: [ 1922.371327] wlan0: associated Mar 6 17:05:19 maxim-laptop kernel: [ 1922.385523] wlan0: disassociating by local choice (reason=3) Mar 6 17:05:30 maxim-laptop kernel: [ 1933.584714] wlan0: authenticate with AP ffff88007e5279e0 Mar 6 17:05:30 maxim-laptop kernel: [ 1933.586701] wlan0: authenticated Mar 6 17:05:30 maxim-laptop kernel: [ 1933.586706] wlan0: associate with AP ffff88007e5279e0 Mar 6 17:05:30 maxim-laptop kernel: [ 1933.589328] wlan0: RX AssocResp from ffff88007ab1c026 (capab=0x411 status=0 aid=1) Mar 6 17:05:30 maxim-laptop kernel: [ 1933.589333] wlan0: associated Mar 6 17:07:59 maxim-laptop kernel: [ 2082.373149] CE: hpet increasing min_delta_ns to 33750 nsec Mar 6 17:10:09 maxim-laptop kernel: [ 2212.381827] usb 7-1: USB disconnect, address 21 Mar 6 17:10:09 maxim-laptop kernel: [ 2212.780057] usb 7-1: new high speed USB device using ehci_hcd and address 22 Mar 6 17:10:09 maxim-laptop kernel: [ 2212.932578] usb 7-1: configuration #1 chosen from 1 choice Mar 6 17:11:30 maxim-laptop kernel: [ 2293.697868] usb 7-1: USB disconnect, address 22 Mar 6 17:11:32 maxim-laptop kernel: [ 2295.364092] usb 7-1: new high speed USB device using ehci_hcd and address 23 Mar 6 17:11:32 maxim-laptop kernel: [ 2295.502710] usb 7-1: configuration #1 chosen from 1 choice Mar 6 17:13:03 maxim-laptop kernel: [ 2386.032222] nfsd: last server has exited, flushing export cache
Of course, thanks for quick reply,
Best regards,
Maxim Levitsky
Quoted 6 lines
Quoted 6 lines
thanks,
greg k-h
Quoted 59 lines · Maxim Levitsky
Quoted 29 lines · Greg KH
Quoted 20 lines · Maxim Levitsky
Hi,
Short summary:
I have HP1018 printer, and it works well in windows. When I use in in linux, I often see messages like:
usbfs:
USBDEVFS_CONTROLfailed cmd python rqt 128 rq 6 len 255 ret -110This is using hp backend that talks to printer using usbfs. I also tried usblp, but it just doesn't say anything in kernel log. I think it silently ignores similar errors, because the end result is the same, the printer sometimes works, but sometimes doesn't. (printer needs firmware to be uploaded to it, and I do upload it).
On the other hand, IF I remove _ether_ ehci-hcd or uhci-hcd from kernel, then everything works fine, I already rebooted the printer many times, used it to print, upload firmware, and everything just work, but as soon as I load the second driver it fails in same way again.
Quoted 5 lines
USB issues with this class of printers are nothing but new, for example see:
http://foo2zjs.rkkda.com/forum/read.php?9,374
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.15/+bug/54419What kernel version are you using?
Quoted 7 lines
Quoted 3 lines
I compiled without
CONFIG_USB_EHCI_ROOT_HUB_TT
and it did help (didn't that much testing, but at least firmware loads ok, and no error messages)Can you provide the full kernel log messages from when you plug in your printer? Are there any other messages saying that you need to be sure to load one driver before the other?
I am familiar with these messages, maybe instead uhci should depend on ehci or something like that?
Tommorow I try to load them manually in correct order. Btw, if I unload both and then load first ehci then uhci, this is ok (if they were loaded incorrectly)
Confirm again that without
CONFIG_USB_EHCI_ROOT_HUB_TTboth drivers work.dmesg (from
/var/log/kern.log.0) attached
It shows how I rebooted the printer often.
It also have this error message about the order.But this isn't related.
I currently blacklisted uhci-hcd, so only ehci-hcd gets loaded. Then I loaded the uhci, and got same bug
(This is why I attached an older dmesg, if you need I reproduce that bug again)
Quoted 3 lines
To be clear, usually after these error messages (... -110), printer stops working, it is so confused, all attempts to access it hang. Only reboot helps.
And of course, forgot, kernel is vanilla 2.6.28
with compat-wireless patches.
Best regards,
Maxim Levitsky
Quoted 34 lines · Maxim Levitsky
Quoted 33 lines · Greg KH
Quoted 20 lines · Maxim Levitsky
Hi,
Short summary:
I have HP1018 printer, and it works well in windows. When I use in in linux, I often see messages like:
usbfs:
USBDEVFS_CONTROLfailed cmd python rqt 128 rq 6 len 255 ret -110This is using hp backend that talks to printer using usbfs. I also tried usblp, but it just doesn't say anything in kernel log. I think it silently ignores similar errors, because the end result is the same, the printer sometimes works, but sometimes doesn't. (printer needs firmware to be uploaded to it, and I do upload it).
On the other hand, IF I remove _ether_ ehci-hcd or uhci-hcd from kernel, then everything works fine, I already rebooted the printer many times, used it to print, upload firmware, and everything just work, but as soon as I load the second driver it fails in same way again.
Quoted 5 lines
USB issues with this class of printers are nothing but new, for example see:
http://foo2zjs.rkkda.com/forum/read.php?9,374
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.15/+bug/54419What kernel version are you using?
Quoted 3 lines
I compiled without
CONFIG_USB_EHCI_ROOT_HUB_TT
and it did help (didn't that much testing, but at least firmware loads ok, and no error messages)
Quoted 5 lines
Quoted 3 lines
Can you provide the full kernel log messages from when you plug in your printer? Are there any other messages saying that you need to be sure to load one driver before the other?
I am familiar with these messages, maybe instead uhci should depend on ehci or something like that?
No, adding a dependency won't work because it is valid to load uhci-hcd without ehci-hcd. The only time a problem occurs is if you load both of them in the wrong order. (And in fact it's pretty rare for that to cause a real problem -- mostly you just get some annoying messages in the log.)
Quoted 12 lines
Tommorow I try to load them manually in correct order. Btw, if I unload both and then load first ehci then uhci, this is ok (if they were loaded incorrectly)
Confirm again that without
CONFIG_USB_EHCI_ROOT_HUB_TTboth drivers work.dmesg (from
/var/log/kern.log.0) attached
It shows how I rebooted the printer often.
It also have this error message about the order.
Quoted 5 lines
But this isn't related.
I currently blacklisted uhci-hcd, so only ehci-hcd gets loaded. Then I loaded the uhci, and got same bug
(This is why I attached an older dmesg, if you need I reproduce that bug again)
The dmesg you attached shows that you unloaded uhci-hcd but the printer still failed to work. This contradicts your statement above that if you remove either driver then everything works fine.
The information in the log isn't really enough to tell what's happening. It would be better if you could provide a usbmon trace showing the problem.
CONFIG_USB_EHCI_ROOT_HUB_TT shouldn't make any difference at all. That setting matters only for hardware using the ARC/TDI design, which is not present in your Intel chipset. Likewise, provided ehci-hcd is loaded first, it shouldn't make any difference whether uhci-hcd is loaded or not.
Alan Stern
Quoted 39 lines · Alan Stern
Quoted 37 lines · Maxim Levitsky
Quoted 36 lines · Greg KH
Quoted 20 lines · Maxim Levitsky
Hi,
Short summary:
I have HP1018 printer, and it works well in windows. When I use in in linux, I often see messages like:
usbfs:
USBDEVFS_CONTROLfailed cmd python rqt 128 rq 6 len 255 ret -110This is using hp backend that talks to printer using usbfs. I also tried usblp, but it just doesn't say anything in kernel log. I think it silently ignores similar errors, because the end result is the same, the printer sometimes works, but sometimes doesn't. (printer needs firmware to be uploaded to it, and I do upload it).
On the other hand, IF I remove _ether_ ehci-hcd or uhci-hcd from kernel, then everything works fine, I already rebooted the printer many times, used it to print, upload firmware, and everything just work, but as soon as I load the second driver it fails in same way again.
Quoted 5 lines
USB issues with this class of printers are nothing but new, for example see:
http://foo2zjs.rkkda.com/forum/read.php?9,374
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.15/+bug/54419What kernel version are you using?
Quoted 3 lines
I compiled without
CONFIG_USB_EHCI_ROOT_HUB_TT
and it did help (didn't that much testing, but at least firmware loads ok, and no error messages)Can you provide the full kernel log messages from when you plug in your printer? Are there any other messages saying that you need to be sure to load one driver before the other?
Quoted 8 lines
Quoted 2 lines
I am familiar with these messages, maybe instead uhci should depend on ehci or something like that?
No, adding a dependency won't work because it is valid to load uhci-hcd without ehci-hcd. The only time a problem occurs is if you load both of them in the wrong order. (And in fact it's pretty rare for that to cause a real problem -- mostly you just get some annoying messages in the log.)
But since it can cause a problem, this has to be somehow automatically fixed isn't it?
For example how to I ensure the correct order with udev?
Quoted 19 lines
Quoted 13 lines
Tommorow I try to load them manually in correct order. Btw, if I unload both and then load first ehci then uhci, this is ok (if they were loaded incorrectly)
Confirm again that without
CONFIG_USB_EHCI_ROOT_HUB_TTboth drivers work.dmesg (from
/var/log/kern.log.0) attached
It shows how I rebooted the printer often.
It also have this error message about the order.Quoted 5 lines
But this isn't related.
I currently blacklisted uhci-hcd, so only ehci-hcd gets loaded. Then I loaded the uhci, and got same bug
(This is why I attached an older dmesg, if you need I reproduce that bug again)
Quoted 3 lines
The dmesg you attached shows that you unloaded uhci-hcd but the printer still failed to work. This contradicts your statement above that if you remove either driver then everything works fine.
We both yes and no:
#define ETIMEDOUT 110
I forgot to tell you that without CONFIG_USB_EHCI_ROOT_HUB_TT or without one of the drivers it is still possible to see that error, if I attempt to query printer status while firmware is loading.
I think this is not a bug, and printer works after such message. This is what you have seen in the logs, I tried to make the printer crash, so I tried the above.
Quoted 11 lines
The information in the log isn't really enough to tell what's happening. It would be better if you could provide a usbmon trace showing the problem.
CONFIG_USB_EHCI_ROOT_HUB_TTshouldn't make any difference at all. That setting matters only for hardware using the ARC/TDI design, which is not present in your Intel chipset. Likewise, provided ehci-hcd is loaded first, it shouldn't make any difference whether uhci-hcd is loaded or not.
Well, I retest this.
But it seems to work
Quoted 2 lines
Alan Stern
Best regards,
Maxim Levitsky
Quoted 7 lines · Maxim Levitsky
Quoted 5 lines
No, adding a dependency won't work because it is valid to load uhci-hcd without ehci-hcd. The only time a problem occurs is if you load both of them in the wrong order. (And in fact it's pretty rare for that to cause a real problem -- mostly you just get some annoying messages in the log.)
But since it can cause a problem, this has to be somehow automatically fixed isn't it?
Can it cause a problem? I'm not so sure -- it depends on what you mean by "problem". One person complained forcefully just because he didn't like all the extra "disconnect" messages in the system log, even though everything worked perfectly.
Quoted 1 line
For example how to I ensure the correct order with udev?
You can't. But you can add rules to /etc/modprobe.conf to insure that ehci-hcd is always loaded before uhci-hcd.
Quoted 7 lines
Quoted 5 lines
CONFIG_USB_EHCI_ROOT_HUB_TTshouldn't make any difference at all. That setting matters only for hardware using the ARC/TDI design, which is not present in your Intel chipset. Likewise, provided ehci-hcd is loaded first, it shouldn't make any difference whether uhci-hcd is loaded or not.Well, I retest this.
But it seems to work
Best would be if you could send two usbmon traces, one showing the problem and one showing what happens when uhci-hcd isn't loaded but everything else is the same. For each test, plug in the printer's USB cable after starting the trace.
And don't try to confuse matters by querying the printer status while reloading its firmware.
Alan Stern
Quoted 25 lines · Alan Stern
Quoted 7 lines · Maxim Levitsky
Quoted 5 lines
No, adding a dependency won't work because it is valid to load uhci-hcd without ehci-hcd. The only time a problem occurs is if you load both of them in the wrong order. (And in fact it's pretty rare for that to cause a real problem -- mostly you just get some annoying messages in the log.)
But since it can cause a problem, this has to be somehow automatically fixed isn't it?
Can it cause a problem? I'm not so sure -- it depends on what you mean by "problem". One person complained forcefully just because he didn't like all the extra "disconnect" messages in the system log, even though everything worked perfectly.
Quoted 1 line
For example how to I ensure the correct order with udev?
You can't. But you can add rules to
/etc/modprobe.confto insure that ehci-hcd is always loaded before uhci-hcd.Quoted 5 lines
Quoted 5 lines
CONFIG_USB_EHCI_ROOT_HUB_TTshouldn't make any difference at all. That setting matters only for hardware using the ARC/TDI design, which is not present in your Intel chipset. Likewise, provided ehci-hcd is loaded first, it shouldn't make any difference whether uhci-hcd is loaded or not.
Quoted 7 lines
Quoted 2 lines
Well, I retest this.
But it seems to workBest would be if you could send two usbmon traces, one showing the problem and one showing what happens when uhci-hcd isn't loaded but everything else is the same. For each test, plug in the printer's USB cable after starting the trace.
Will do soon.
Quoted 3 lines
And don't try to confuse matters by querying the printer status while reloading its firmware.
Well, I suspected that there is some concurrent access from both usb drivers, so I tried all options to crash it....
Quoted 2 lines
Alan Stern
Quoted 26 lines · Maxim Levitsky
Quoted 25 lines · Alan Stern
Quoted 7 lines · Maxim Levitsky
Quoted 5 lines
No, adding a dependency won't work because it is valid to load uhci-hcd without ehci-hcd. The only time a problem occurs is if you load both of them in the wrong order. (And in fact it's pretty rare for that to cause a real problem -- mostly you just get some annoying messages in the log.)
But since it can cause a problem, this has to be somehow automatically fixed isn't it?
Can it cause a problem? I'm not so sure -- it depends on what you mean by "problem". One person complained forcefully just because he didn't like all the extra "disconnect" messages in the system log, even though everything worked perfectly.
Quoted 1 line
For example how to I ensure the correct order with udev?
You can't. But you can add rules to
/etc/modprobe.confto insure that ehci-hcd is always loaded before uhci-hcd.Quoted 5 lines
Quoted 5 lines
CONFIG_USB_EHCI_ROOT_HUB_TTshouldn't make any difference at all. That setting matters only for hardware using the ARC/TDI design, which is not present in your Intel chipset. Likewise, provided ehci-hcd is loaded first, it shouldn't make any difference whether uhci-hcd is loaded or not.
Quoted 7 lines
Quoted 7 lines
Quoted 2 lines
Well, I retest this.
But it seems to workBest would be if you could send two usbmon traces, one showing the problem and one showing what happens when uhci-hcd isn't loaded but everything else is the same. For each test, plug in the printer's USB cable after starting the trace.
Sorry, sorry, sorry.
is was the CONFIG_USB_EHCI_TT_NEWSCHED that did it.
I confused both options, without the above option printer works flawlessly.
In addition I instructed modprobe to load ehci when it loads uhci, and then uhci.
Truth is truth, I have again seen same timeout messages, just after I reboot the printer. It is possible that some of the hp scripts, eg the one that loads firmware, queries the printer while firmware loads or so, anyway even after such message printer works (I printed a page using it).
Now I will enable again the CONFIG_USB_EHCI_TT_NEWSCHED, and see how fast it will fail.
Best regards,
Maxim Levitsky
Quoted 5 lines · Maxim Levitsky
Sorry, sorry, sorry.
is was the
CONFIG_USB_EHCI_TT_NEWSCHEDthat did it.
I confused both options, without the above option printer works flawlessly.
Is your printer connected directly to the computer, or does it go through a hub? (If it is connected directly then EHCI_TT_NEWSCHED should not affect it at all.)
If it does go through a hub, does it behave better when you attach it directly?
Alan Stern
Quoted 8 lines · Alan Stern
Quoted 5 lines · Maxim Levitsky
Sorry, sorry, sorry.
is was the
CONFIG_USB_EHCI_TT_NEWSCHEDthat did it.
I confused both options, without the above option printer works flawlessly.
Quoted 9 lines
Is your printer connected directly to the computer, or does it go through a hub? (If it is connected directly then
EHCI_TT_NEWSCHEDshould not affect it at all.)If it does go through a hub, does it behave better when you attach it directly?
Alan Stern
No, it is connected directly.
Just tried 'bad' driver, and firmware upload failed
Do you mean that CONFIG_USB_EHCI_TT_NEWSCHED doesn't affect the driver at all when no hub is presented?
Btw, at least according to lsusb -t, there are no internal hubs in the printer.
But it can be a coincidence, it seems that with 'bad' driver printer works 'better' to as it failed back few days ago much more often, maybe cable is bad, don't know, but according to the web these printers 1018/1020.. have usb problems, there is even a readme for that in foo2zjz
I try to use the 'good' driver
(without CONFIG_USB_EHCI_TT_NEWSCHED) for some time.
Best regards,
Maxim Levitsky
Quoted 7 lines · Maxim Levitsky
Quoted 7 lines
Is your printer connected directly to the computer, or does it go through a hub? (If it is connected directly then
EHCI_TT_NEWSCHEDshould not affect it at all.)If it does go through a hub, does it behave better when you attach it directly?
Quoted 7 lines
Quoted 2 lines
Alan Stern
No, it is connected directly.
Just tried 'bad' driver, and firmware upload failedDo you mean that
CONFIG_USB_EHCI_TT_NEWSCHEDdoesn't affect the driver at all when no hub is presented?
That's right. Transaction Translators (TTs) live inside hubs. If you don't use a hub then the TT code never runs.
Quoted 2 lines
Btw, at least according to lsusb -t, there are no internal hubs in the printer.
What does /proc/bus/usb/devices say?
Quoted 8 lines
But it can be a coincidence, it seems that with 'bad' driver printer works 'better' to as it failed back few days ago much more often, maybe cable is bad, don't know, but according to the web these printers 1018/1020.. have usb problems, there is even a readme for that in foo2zjz
I try to use the 'good' driver
(withoutCONFIG_USB_EHCI_TT_NEWSCHED) for some time.
Please don't forget to collect usbmon traces when the problem occurs.
Alan Stern
Quoted 17 lines · Alan Stern
Quoted 7 lines · Maxim Levitsky
Quoted 7 lines
Is your printer connected directly to the computer, or does it go through a hub? (If it is connected directly then
EHCI_TT_NEWSCHEDshould not affect it at all.)If it does go through a hub, does it behave better when you attach it directly?
Quoted 7 lines
Quoted 2 lines
Alan Stern
No, it is connected directly.
Just tried 'bad' driver, and firmware upload failedDo you mean that
CONFIG_USB_EHCI_TT_NEWSCHEDdoesn't affect the driver at all when no hub is presented?
Quoted 8 lines
That's right. Transaction Translators (TTs) live inside hubs. If you don't use a hub then the TT code never runs.
Quoted 2 lines
Btw, at least according to lsusb -t, there are no internal hubs in the printer.
What does
/proc/bus/usb/devicessay?
Ubuntu doesn't seem to mount usbfs on /proc/bus/usb, so:
sudo mount -tusbfs none /proc/bus/usb
maxim@maxim-laptop:~$ cat /proc/bus/usb/devices
T: Bus=07 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev= 2.06 S: Manufacturer=Linux 2.6.28 uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:1d.2
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=06 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev= 2.06 S: Manufacturer=Linux 2.6.28 uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:1d.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=05 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev= 2.06 S: Manufacturer=Linux 2.6.28 uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:1d.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=04 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev= 2.06 S: Manufacturer=Linux 2.6.28 uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:1a.1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=03 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2 B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0001 Rev= 2.06 S: Manufacturer=Linux 2.6.28 uhci_hcd S: Product=UHCI Host Controller S: SerialNumber=0000:00:1a.0
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 6 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.28 ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:1d.7
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=03f0 ProdID=4117 Rev= 1.00 S: Manufacturer=Hewlett-Packard S: Product=HP LaserJet 1018 S: SerialNumber=KP06J6V C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 98mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=(none) E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(unk. ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=064e ProdID=a101 Rev= 1.00 S: Manufacturer=SuYin S: Product=Acer CrystalEye webcam S: SerialNumber=CN0314-OV03-VA-R02.00.00
C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=0e(video) Sub=03 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=0e(video) Sub=01 Prot=00 Driver=uvcvideo
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 0 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
I: If#= 1 Alt= 1 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 128 Ivl=125us I: If#= 1 Alt= 2 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 256 Ivl=125us I: If#= 1 Alt= 3 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 800 Ivl=125us I: If#= 1 Alt= 4 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=1600 Ivl=125us I: If#= 1 Alt= 5 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=2400 Ivl=125us I: If#= 1 Alt= 6 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=3000 Ivl=125us
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 4 B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0 D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=1d6b ProdID=0002 Rev= 2.06 S: Manufacturer=Linux 2.6.28 ehci_hcd S: Product=EHCI Host Controller S: SerialNumber=0000:00:1a.7
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
Quoted 10 lines
Quoted 8 lines
But it can be a coincidence, it seems that with 'bad' driver printer works 'better' to as it failed back few days ago much more often, maybe cable is bad, don't know, but according to the web these printers 1018/1020.. have usb problems, there is even a readme for that in foo2zjz
I try to use the 'good' driver
(withoutCONFIG_USB_EHCI_TT_NEWSCHED) for some time.Please don't forget to collect usbmon traces when the problem occurs.
No problem, I would.
Thanks a lot,
Best regards,
Maxim Levitsky
Quoted 3 lines
Alan Stern
Quoted 22 lines · Maxim Levitsky
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=03f0 ProdID=4117 Rev= 1.00 S: Manufacturer=Hewlett-Packard S: Product=HP LaserJet 1018 S: SerialNumber=KP06J6V C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 98mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=(none) E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0msT: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(unk. ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=064e ProdID=a101 Rev= 1.00 S: Manufacturer=SuYin S: Product=Acer CrystalEye webcam S: SerialNumber=CN0314-OV03-VA-R02.00.00C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=0e(video) Sub=03 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=0e(video) Sub=01 Prot=00 Driver=uvcvideo
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 0 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo
Quoted 12 lines
I: If#= 1 Alt= 1 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 128 Ivl=125us I: If#= 1 Alt= 2 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 256 Ivl=125us I: If#= 1 Alt= 3 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 800 Ivl=125us I: If#= 1 Alt= 4 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=1600 Ivl=125us I: If#= 1 Alt= 5 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=2400 Ivl=125us I: If#= 1 Alt= 6 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=3000 Ivl=125us
I wonder... Does it make any difference if you unplug that webcam, or plug it into the other high-speed bus?
Alan Stern
Quoted 37 lines · Alan Stern
Quoted 22 lines · Maxim Levitsky
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=03f0 ProdID=4117 Rev= 1.00 S: Manufacturer=Hewlett-Packard S: Product=HP LaserJet 1018 S: SerialNumber=KP06J6V C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 98mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=(none) E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0msT: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(unk. ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=064e ProdID=a101 Rev= 1.00 S: Manufacturer=SuYin S: Product=Acer CrystalEye webcam S: SerialNumber=CN0314-OV03-VA-R02.00.00C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=0e(video) Sub=03 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=0e(video) Sub=01 Prot=00 Driver=uvcvideo
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 0 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideoQuoted 12 lines
I: If#= 1 Alt= 1 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 128 Ivl=125us I: If#= 1 Alt= 2 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 256 Ivl=125us I: If#= 1 Alt= 3 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 800 Ivl=125us I: If#= 1 Alt= 4 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=1600 Ivl=125us I: If#= 1 Alt= 5 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=2400 Ivl=125us I: If#= 1 Alt= 6 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=3000 Ivl=125us
Quoted 2 lines
I wonder... Does it make any difference if you unplug that webcam, or plug it into the other high-speed bus?
Can't do so, its built-in.
Best regards,
Maxim Levitsky
Quoted 38 lines · Maxim Levitsky
Quoted 37 lines · Alan Stern
Quoted 34 lines · Maxim Levitsky
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 7 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=03f0 ProdID=4117 Rev= 1.00 S: Manufacturer=Hewlett-Packard S: Product=HP LaserJet 1018 S: SerialNumber=KP06J6V C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 98mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=07(print) Sub=01 Prot=02 Driver=(none) E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0msT: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 2 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=ef(unk. ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=064e ProdID=a101 Rev= 1.00 S: Manufacturer=SuYin S: Product=Acer CrystalEye webcam S: SerialNumber=CN0314-OV03-VA-R02.00.00C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=0e(video) Sub=03 Prot=00
I:* If#= 0 Alt= 0 #EPs= 1 Cls=0e(video) Sub=01 Prot=00 Driver=uvcvideo
E: Ad=83(I) Atr=03(Int.) MxPS= 16 Ivl=4ms
I:* If#= 1 Alt= 0 #EPs= 0 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideoI: If#= 1 Alt= 1 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 128 Ivl=125us I: If#= 1 Alt= 2 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 256 Ivl=125us I: If#= 1 Alt= 3 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS= 800 Ivl=125us I: If#= 1 Alt= 4 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=1600 Ivl=125us I: If#= 1 Alt= 5 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=2400 Ivl=125us I: If#= 1 Alt= 6 #EPs= 1 Cls=0e(video) Sub=02 Prot=00 Driver=uvcvideo E: Ad=81(I) Atr=05(Isoc) MxPS=3000 Ivl=125us
Quoted 3 lines
Quoted 2 lines
I wonder... Does it make any difference if you unplug that webcam, or plug it into the other high-speed bus?
Can't do so, its built-in.
But I can plug printer into another usb bus, I found a single port (this notebook has 4 ports) that is on bus #1, problem is that it it on the other side of the notebook, and from the point where the printer stands the cable isn't long enough to reach it.
I do some more testing soon, buy another and longer cable
Anyway couldn't crash the printer even once with 'good' driver. In other words I was sure I found a cause for this problem, but it seems I found nothing or maybe a bad cable (I did some tests in windows - but as things unroll, this printer can work quite reliably sometimes that is)
So again big thanks,
Best regards,
Maxim Levitsky