Skip to contentSkip to conversation

OMAP3, Zoom2 Initializing GPIO bank clocks

U-Boot New Tom Rix 2 participants 5 messages May 29, 2009 – Jun 3, 2009

lore
Share & tools
lore

Tom Rix

author
#0 lore raw

In OMAP3, the GPIO bank clocks should only be turned on as needed. This is done at the config file level.
Zoom2 uses GPIO so it must turn on the GPIO bank clocks it needs.

author
#1 lore raw

PATCH 1/2 OMAP3 Turn on the GPIO bank clocks

The function and interface clocks for each GPIO bank, except the first, must be explicitly turned on. These are controlled by the config level defines CONFIG_OMAP3_GPIO_n where n is from 2 to 6.

---
 cpu/arm_cortexa8/omap3/clock.c |   22 ++++++++++++++++++++++
 1 files changed, 22 insertions(+), 0 deletions(-)
cpu/arm_cortexa8/omap3/clock.c +22 -0
index d035677..0306b6c 100644
@@ -357,6 +357,28 @@ void per_clocks_enable(void)
 	sr32(&prcm_base->fclken_per, 11, 1, 0x1);
 	sr32(&prcm_base->iclken_per, 11, 1, 0x1);
 #endif
+
+#ifdef CONFIG_OMAP3_GPIO_2
+	sr32(&prcm_base->fclken_per, 13, 1, 1);
+	sr32(&prcm_base->iclken_per, 13, 1, 1);
+#endif
+#ifdef CONFIG_OMAP3_GPIO_3
+	sr32(&prcm_base->fclken_per, 14, 1, 1);
+	sr32(&prcm_base->iclken_per, 14, 1, 1);
+#endif
+#ifdef CONFIG_OMAP3_GPIO_4
+	sr32(&prcm_base->fclken_per, 15, 1, 1);
+	sr32(&prcm_base->iclken_per, 15, 1, 1);
+#endif
+#ifdef CONFIG_OMAP3_GPIO_5
+	sr32(&prcm_base->fclken_per, 16, 1, 1);
+	sr32(&prcm_base->iclken_per, 16, 1, 1);
+#endif
+#ifdef CONFIG_OMAP3_GPIO_6
+	sr32(&prcm_base->fclken_per, 17, 1, 1);
+	sr32(&prcm_base->iclken_per, 17, 1, 1);
+#endif
+
 #ifdef CONFIG_DRIVER_OMAP34XX_I2C
 	/* Turn on all 3 I2C clocks */
 	sr32(&prcm_base->fclken1_core, 15, 3, 0x7);
Signature · 1 line
1.6.0.5
author
#2 lore raw

PATCH 2/2 ZOOM2 Define GPIO banks used.

Enable the function and interface clocks for banks 2,3,5 and 6.

---
 include/configs/omap3_zoom2.h |    8 ++++++++
 1 files changed, 8 insertions(+), 0 deletions(-)
include/configs/omap3_zoom2.h +8 -0
index e257419..c2ad5bf 100644
@@ -115,6 +115,14 @@
 /* Optional value */
 #define STATUS_LED_BOOT			STATUS_LED_BIT
 
+/* GPIO banks */
+#ifdef CONFIG_STATUS_LED
+#define CONFIG_OMAP3_GPIO_2 /* ZOOM2_LED_BLUE2 */
+#define CONFIG_OMAP3_GPIO_6 /* ZOOM2_LED_RED */
+#endif
+#define CONFIG_OMAP3_GPIO_3 /* board revision */
+#define CONFIG_OMAP3_GPIO_5 /* debug board detection, ZOOM2_LED_BLUE */
+
 /* commands to include */
 #include <config_cmd_default.h>
 
Signature · 1 line
1.6.0.5