Skip to contentSkip to conversation

remove _IO_BASE and KSEG1ADDR from board configuration files

PATCH Superseded Timur Tabi 3 participants 4 messages Jun 19, 2009 – Jul 10, 2009

lore
Share & tools
lore

Timur Tabi

author
#0 lore raw

PATCH v3 1/1 remove _IO_BASE and KSEG1ADDR from board configuration files

The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet driver, but the code that used that macro was removed over a year ago, so board configuration files no longer need to define it.

The _IO_BASE macro is also automatically defined to 0 if it isn't already set, so there's no need to define that macro either in the board configuration files.

---

v3: removed the change for PN62.h, which does not have _IO_BASE at 0

 include/configs/HIDDEN_DRAGON.h |    4 +---
 include/configs/M5253DEMO.h     |    1 -
 include/configs/M5253EVBE.h     |    1 -
 include/configs/M54455EVB.h     |    1 -
 include/configs/MPC8349ITX.h    |    7 -------
 include/configs/MPC8536DS.h     |    6 ------
 include/configs/MPC8544DS.h     |    6 ------
 include/configs/MPC8572DS.h     |    6 ------
 include/configs/MPC8610HPCD.h   |    4 ----
 include/configs/MPC8641HPCN.h   |    4 ----
 include/configs/MVBLM7.h        |    2 --
 include/configs/P2020DS.h       |    6 ------
 include/configs/mpc7448hpc2.h   |    4 ----
 include/configs/r2dplus.h       |    2 --
 14 files changed, 1 insertions(+), 53 deletions(-)
include/configs/HIDDEN_DRAGON.h +1 -3
index f6777b9..251fe67 100644
@@ -103,9 +103,7 @@
 #define PCI_ENET1_MEMADDR	0x81000000
 
 #define CONFIG_RTL8139
-#define _IO_BASE	    0x00000000
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x)	    (x)
+
 /* Make sure the ethaddr can be overwritten
    TODO: Remove this on final product
 */
include/configs/M5253DEMO.h +0 -1
index 50b3a03..5e86e4c 100644
@@ -85,7 +85,6 @@
 #	define CONFIG_SYS_ATA_REG_OFFSET	0xA0	/* Offset for normal register accesses */
 #	define CONFIG_SYS_ATA_ALT_OFFSET	0xC0	/* Offset for alternate registers */
 #	define CONFIG_SYS_ATA_STRIDE		4	/* Interval between registers */
-#	define _IO_BASE			0
 #endif
 
 #define CONFIG_NET_MULTI		1
include/configs/M5253EVBE.h +0 -1
index cf8b773..df6970c 100644
@@ -91,7 +91,6 @@
 #define CONFIG_SYS_ATA_REG_OFFSET	0xA0	/* Offset for normal register accesses */
 #define CONFIG_SYS_ATA_ALT_OFFSET	0xC0	/* Offset for alternate registers */
 #define CONFIG_SYS_ATA_STRIDE		4	/* Interval between registers */
-#define _IO_BASE		0
 
 #define CONFIG_SYS_PROMPT		"=> "
 #define CONFIG_SYS_LONGHELP		/* undef to save memory */
include/configs/M54455EVB.h +0 -1
index 101dced..87f3a73 100644
@@ -180,7 +180,6 @@
 #define CONFIG_SYS_ATA_REG_OFFSET	0xA0	/* Offset for normal register accesses */
 #define CONFIG_SYS_ATA_ALT_OFFSET	0xC0	/* Offset for alternate registers           */
 #define CONFIG_SYS_ATA_STRIDE		4	/* Interval between registers                 */
-#define _IO_BASE		0
 
 /* Realtime clock */
 #define CONFIG_MCFRTC
include/configs/MPC8349ITX.h +0 -7
index f2e574b..d4d3256 100644
@@ -360,16 +360,9 @@ boards, we say we have two, but don't display a message if we find only one. */
 #define CONFIG_SYS_PCI2_IO_SIZE	0x01000000	/* 16M */
 #endif
 
-#define _IO_BASE		0x00000000	/* points to PCI I/O space */
-
 #define CONFIG_NET_MULTI
 #define CONFIG_PCI_PNP			/* do pci plug-and-play */
 
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x)	    (x)
-#endif
-
 #ifndef CONFIG_PCI_PNP
     #define PCI_ENET0_IOADDR	0x00000000
     #define PCI_ENET0_MEMADDR	CONFIG_SYS_PCI2_MEM_BASE
include/configs/MPC8536DS.h +0 -6
index 9e00b89..7085d28 100644
@@ -427,12 +427,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #undef CONFIG_TULIP
 #undef CONFIG_RTL8139
 
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x)		({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
-#define _IO_BASE	0x00000000
-#endif
-
 #ifndef CONFIG_PCI_PNP
 	#define PCI_ENET0_IOADDR	CONFIG_SYS_PCI1_IO_BUS
 	#define PCI_ENET0_MEMADDR	CONFIG_SYS_PCI1_IO_BUS
include/configs/MPC8544DS.h +0 -6
index 59cfde6..1d8fecf 100644
@@ -340,12 +340,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 #undef CONFIG_TULIP
 #define CONFIG_RTL8139
 
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x)		(x)
-#define _IO_BASE	0x00000000
-#endif
-
 #ifndef CONFIG_PCI_PNP
 	#define PCI_ENET0_IOADDR	CONFIG_SYS_PCI1_IO_BUS
 	#define PCI_ENET0_MEMADDR	CONFIG_SYS_PCI1_IO_BUS
include/configs/MPC8572DS.h +0 -6
index 2aba689..c7385e4 100644
@@ -484,12 +484,6 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #undef CONFIG_TULIP
 #undef CONFIG_RTL8139
 
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x)		(x)
-#define _IO_BASE	0x00000000
-#endif
-
 #ifndef CONFIG_PCI_PNP
 	#define PCI_ENET0_IOADDR	CONFIG_SYS_PCIE3_IO_BUS
 	#define PCI_ENET0_MEMADDR	CONFIG_SYS_PCIE3_IO_BUS
include/configs/MPC8610HPCD.h +0 -4
index 1091043..2f40ef4 100644
@@ -280,10 +280,6 @@
 #define CONFIG_SYS_PCI1_IO_VIRT	0xe1000000
 #define CONFIG_SYS_PCI1_IO_SIZE	0x00100000	/* 1M */
 
-/* For RTL8139 */
-#define KSEG1ADDR(x)	({u32 _x = le32_to_cpu(*(u32 *)(x)); (&_x); })
-#define _IO_BASE		0x00000000
-
 /* controller 1, Base address 0xa000 */
 #define CONFIG_SYS_PCIE1_MEM_BUS	0xa0000000
 #define CONFIG_SYS_PCIE1_MEM_PHYS	CONFIG_SYS_PCIE1_MEM_BUS
include/configs/MPC8641HPCN.h +0 -4
index d8042fb..de2cf1a 100644
@@ -348,10 +348,6 @@ extern unsigned long get_board_sys_clk(unsigned long dummy);
 				 | CONFIG_SYS_PHYS_ADDR_HIGH)
 #define CONFIG_SYS_PCI1_IO_SIZE	0x00010000	/* 64K */
 
-/* For RTL8139 */
-#define KSEG1ADDR(x)		({u32 _x=le32_to_cpu(*(u32 *)(x)); (&_x);})
-#define _IO_BASE		0x00000000
-
 #ifdef CONFIG_PHYS_64BIT
 /*
  * Use the same PCI bus address on PCI1 and PCI2 if we have PHYS_64BIT.
include/configs/MVBLM7.h +0 -2
index 9675205..ac8cb57 100644
@@ -193,8 +193,6 @@
 #define CONFIG_SYS_PCI1_IO_PHYS	0xE2000000
 #define CONFIG_SYS_PCI1_IO_SIZE	0x01000000
 
-#define _IO_BASE		0x00000000
-
 #define CONFIG_NET_MULTI	1
 #define CONFIG_NET_RETRY_COUNT	3
 
include/configs/P2020DS.h +0 -6
index a39ff26..443bc40 100644
@@ -517,12 +517,6 @@ extern unsigned long calculate_board_ddr_clk(unsigned long dummy);
 #undef CONFIG_TULIP
 #define CONFIG_RTL8139
 
-#ifdef CONFIG_RTL8139
-/* This macro is used by RTL8139 but not defined in PPC architecture */
-#define KSEG1ADDR(x)		(x)
-#define _IO_BASE	0x00000000
-#endif
-
 #ifndef CONFIG_PCI_PNP
 	#define PCI_ENET0_IOADDR	CONFIG_SYS_PCIE3_IO_BUS
 	#define PCI_ENET0_MEMADDR	CONFIG_SYS_PCIE3_IO_BUS
include/configs/mpc7448hpc2.h +0 -4
index 7d42155..4f98ba4 100644
@@ -124,8 +124,6 @@
 
 /* Networking Configuration */
 
-#define KSEG1ADDR(a)	(a)	/* Needed by the rtl8139 driver */
-
 #define CONFIG_TSI108_ETH
 #define CONFIG_TSI108_ETH_NUM_PORTS	2
 
@@ -303,8 +301,6 @@
 
 #define CONFIG_SYS_PCI_IO_SIZE		0x01000000	/* 16MB */
 
-#define _IO_BASE		0x00000000	/* points to PCI I/O space      */
-
 /* PCI Config Space mapping */
 #define CONFIG_SYS_PCI_CFG_BASE	0xfb000000	/* Changed from FE000000 */
 #define CONFIG_SYS_PCI_CFG_SIZE	0x01000000	/* 16MB */
include/configs/r2dplus.h +0 -2
index 6fa1eaf..37d4fff 100644
@@ -123,7 +123,5 @@
  */
 #define CONFIG_NET_MULTI
 #define CONFIG_RTL8139
-#define _IO_BASE		0x00000000
-#define KSEG1ADDR(x)		(x)
 
 #endif /* __CONFIG_H */
Signature · 1 line
1.6.0.6
#1 lore raw

PATCH v3 1/1 remove _IO_BASE and KSEG1ADDR from board configuration files

Quoted 4 lines · On Fri, 19 Jun 2009 14:10:52 -0500 Timur Tabi <[email protected]> wrote:

The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet driver, but the code that used that macro was removed over a year ago, so board configuration files no longer need to define it.

Quoted 8 lines

The _IO_BASE macro is also automatically defined to 0 if it isn't already set, so there's no need to define that macro either in the board configuration files.

---

ack

Kim

author
#2 lore raw

PATCH v3 1/1 remove _IO_BASE and KSEG1ADDR from board configuration files

In reply to Timur Tabi

Wolfgang, please apply this version of the patch. Thanks.

Quoted 14 lines · Timur Tabi

The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet driver, but the code that used that macro was removed over a year ago, so board configuration files no longer need to define it.

The _IO_BASE macro is also automatically defined to 0 if it isn't already set, so there's no need to define that macro either in the board configuration files.

---

v3: removed the change for PN62.h, which does not have _IO_BASE at 0

Signature · 2 lines
Timur Tabi
Linux kernel developer at Freescale
#3 lore raw

PATCH v3 1/1 remove _IO_BASE and KSEG1ADDR from board configuration files

In reply to Timur Tabi

Dear Timur Tabi,

Quoted 15 lines · In message <[email protected]> you wrote:

The KSEG1ADDR macro used to be necessary for the RTL8139 Ethernet driver, but the code that used that macro was removed over a year ago, so board configuration files no longer need to define it.

The _IO_BASE macro is also automatically defined to 0 if it isn't already set, so there's no need to define that macro either in the board configuration files.

---

v3: removed the change for PN62.h, which does not have _IO_BASE at 0

Quoted 15 lines
 include/configs/HIDDEN_DRAGON.h |    4 +---
 include/configs/M5253DEMO.h     |    1 -
 include/configs/M5253EVBE.h     |    1 -
 include/configs/M54455EVB.h     |    1 -
 include/configs/MPC8349ITX.h    |    7 -------
 include/configs/MPC8536DS.h     |    6 ------
 include/configs/MPC8544DS.h     |    6 ------
 include/configs/MPC8572DS.h     |    6 ------
 include/configs/MPC8610HPCD.h   |    4 ----
 include/configs/MPC8641HPCN.h   |    4 ----
 include/configs/MVBLM7.h        |    2 --
 include/configs/P2020DS.h       |    6 ------
 include/configs/mpc7448hpc2.h   |    4 ----
 include/configs/r2dplus.h       |    2 --
 14 files changed, 1 insertions(+), 53 deletions(-)

Applied, thanks.

Best regards,

Wolfgang Denk

Signature · 5 lines
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"Why waste negative entropy on comments, when you could use the  same
entropy to create bugs instead?"                        - Steve Elias