use common code for mvBC-P (MPC5200)
PATCH 2/2 use common code for mvBC-P (MPC5200)
This patch makes use of common code, i.e. removes duplicate board specific code. Additionally some hard coded numbers have been replace by definitions and an configurable PCI latency has been added.
---
board/matrix_vision/mvbc_p/mvbc_p.c | 94 +++++--------------------- board/matrix_vision/mvbc_p/mvbc_p.h | 2 +- board/matrix_vision/mvbc_p/mvbc_p_autoscript | 10 ++- 3 files changed, 24 insertions(+), 82 deletions(-)
(quoted diff) +0 -0
b/board/matrix_vision/mvbc_p/mvbc_p.c
index a300342..59bbb5a 100644
board/matrix_vision/mvbc_p/mvbc_p.c +6 -18
@@ -134,23 +134,6 @@ void mvbc_init_gpio(void)printf ("sint_gpioe : 0x%08x\n" , gpio->sint_gpioe); } -void reset_environment (void ) -{ -char *s, sernr[64 ]; - -printf ("\n*** RESET ENVIRONMENT ***\n" ); -memset (sernr,0 ,sizeof (sernr)); - s =getenv ("serial#" ); -if (s) { -printf ("found serial# : %s\n" , s); -strncpy (sernr, s,64 ); - } - gd->env_valid =0 ; -env_relocate (); -if (s) -setenv ("serial#" , sernr); -} -int misc_init_r (void ) {char *s =getenv ("reset_env" );
@@ -166,7 +149,7 @@ int misc_init_r(void)return 0 ; }printf (" === FACTORY RESET ===\n" ); -reset_environment (); +mv_reset_environment ();saveenv ();return -1 ;
@@ -206,7 +189,12 @@ void flash_afterinit(ulong size)void pci_mvbc_fixup_irq (struct pci_controller *hose,pci_dev_t dev) {unsigned char line =0xff ; +char *s =getenv ("pci_latency" );u32 base; +u8 val =0 ; + +if (s) + val =simple_strtoul (s,NULL ,16 );if (PCI_BUS (dev) ==0 ) {switch (PCI_DEV (dev)) {
@@ -216,9 +204,13 @@ void pci_mvbc_fixup_irq(struct pci_controller
*hose, pci_dev_t dev)
printf("found FPA - enable arbitration\n"); writel(0x03, (u32*)(base + 0x80c0)); writel(0xf0, (u32*)(base + 0x8080));
+ if (val)
+ pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, val);
break;
case 0xb: /* LAN */
line = 2;
+ if (val)
+ pci_hose_write_config_byte(hose, dev, PCI_LATENCY_TIMER, val);
break;
case 0x1a:
break;
@@ -234,85 +226,31 @@ struct pci_controller hose = {
fixup_irq:pci_mvbc_fixup_irq
};
-int mvbc_p_load_fpga(void)
-{
- size_t data_size = 0;
- void *fpga_data = NULL;
- char *datastr = getenv("fpgadata");
- char *sizestr = getenv("fpgadatasize");
-
- if (datastr)
- fpga_data = (void *)simple_strtoul(datastr, NULL, 16);
- if (sizestr)
- data_size = (size_t)simple_strtoul(sizestr, NULL, 16);
-
- return fpga_load(0, fpga_data, data_size);
-}
-
extern void pci_mpc5xxx_init(struct pci_controller *);
void pci_init_board(void)
{
- char *s;
- int load_fpga = 1;
-
mvbc_p_init_fpga();
- s = getenv("skip_fpga");
- if (s) {
- printf("found 'skip_fpga' -> FPGA _not_ loaded !\n");
- load_fpga = 0;
- }
- if (load_fpga) {
- printf("loading FPGA ... ");
- mvbc_p_load_fpga();
- printf("done\n");
- }
+ mv_load_fpga();
pci_mpc5xxx_init(&hose);
}
-u8 *dhcp_vendorex_prep(u8 *e)
-{
- char *ptr;
-
- /* DHCP vendor-class-identifier = 60 */
- if ((ptr = getenv("dhcp_vendor-class-identifier"))) {
- *e++ = 60;
- *e++ = strlen(ptr);
- while (*ptr)
- *e++ = *ptr++;
- }
- /* DHCP_CLIENT_IDENTIFIER = 61 */
- if ((ptr = getenv("dhcp_client_id"))) {
- *e++ = 61;
- *e++ = strlen(ptr);
- while (*ptr)
- *e++ = *ptr++;
- }
-
- return e;
-}
-
-u8 *dhcp_vendorex_proc (u8 *popt)
-{
- return NULL;
-}
-
void show_boot_progress(int val)
{
struct mpc5xxx_gpio *gpio = (struct mpc5xxx_gpio*)MPC5XXX_GPIO;
switch(val) {
case 0: /* FPGA ok */
- setbits_be32(&gpio->simple_dvo, 0x80);
+ setbits_be32(&gpio->simple_dvo, LED_G0);
break;
- case 1:
- setbits_be32(&gpio->simple_dvo, 0x40);
+ case 65:
+ setbits_be32(&gpio->simple_dvo, LED_G1);
break;
case 12:
- setbits_be32(&gpio->simple_dvo, 0x20);
+ setbits_be32(&gpio->simple_dvo, LED_Y);
break;
case 15:
- setbits_be32(&gpio->simple_dvo, 0x10);
+ setbits_be32(&gpio->simple_dvo, LED_R);
break;
default:
break;
(quoted diff) +0 -0
b/board/matrix_vision/mvbc_p/mvbc_p.h
index 3330798..be1542b 100644
board/matrix_vision/mvbc_p/mvbc_p.h +1 -1
@@ -23,7 +23,7 @@#define SIMPLE_DDR (LED_G0 | LED_G1 | LED_Y | LED_R | \ FPGA_DIN | FPGA_CCLK | FPGA_CONFIG | WD_WDI)#define SIMPLE_DVO (FPGA_CONFIG) -#define SIMPLE_ODE (FPGA_CONFIG) +#define SIMPLE_ODE (FPGA_CONFIG | LED_G0 | LED_G1 | LED_Y | LED_R)#define SIMPLE_GPIOEN (LED_G0 | LED_G1 | LED_Y | LED_R | \ FPGA_DIN | FPGA_CCLK | FPGA_CONF_DONE | FPGA_CONFIG |\ WD_WDI | COP_PRESENT)
(quoted diff) +0 -0
b/board/matrix_vision/mvbc_p/mvbc_p_autoscript index 5cee6c5..1102354 100644
board/matrix_vision/mvbc_p/mvbc_p_autoscript +0 -0
@@ -5,7 +5,7 @@ setenv bootdtb bootm \${kernel_boot} \
${mv_initrd_addr_ram} \${mv_dtb_addr_ram}
setenv ramkernel setenv kernel_boot \${loadaddr}
setenv flashkernel setenv kernel_boot \${mv_kernel_addr} setenv cpird cp \${mv_initrd_addr} \${mv_initrd_addr_ram} \
${mv_initrd_length}
-setenv bootfromflash run flashkernel cpird ramparam addcons e1000para bootdtb
+setenv bootfromflash run flashkernel cpird ramparam addcons e1000para addprofile bootdtb
setenv getdtb tftp \${mv_dtb_addr_ram} \${dtb_name}
setenv cpdtb cp \${mv_dtb_addr} \${mv_dtb_addr_ram} 0x2000 setenv rundtb fdt addr \${mv_dtb_addr_ram}\;fdt boardsetup
@@ -16,12 +16,16 @@ setenv addcons setenv bootargs \${bootargs} console=ttyPSC\${console_nr},\${baud
else
setenv addcons setenv bootargs \${bootargs} console=tty0
fi
-setenv e1000para setenv bootargs \${bootargs} e1000.TxDescriptors=1500 e1000.SmartPowerDownEnable=1
+setenv e1000para setenv bootargs \${bootargs} e1000.TxDescriptors=256 e1000.SmartPowerDownEnable=1
setenv set_static_ip setenv ipaddr \${static_ipaddr}
setenv set_static_nm setenv netmask \${static_netmask} setenv set_static_gw setenv gatewayip \${static_gateway} setenv set_ip setenv ip \${ipaddr}::\${gatewayip}:\${netmask} setenv ramparam setenv bootargs root=/dev/ram0 ro rootfstype=squashfs
+if test ${oprofile} = yes;
+then
+setenv addprofile setenv bootargs \${bootargs} profile=\${profile} +fi
if test ${autoscr_boot} != no;
then
if test ${netboot} = yes;
@@ -31,7 +35,7 @@ then
then
echo "=== bootp succeeded -> netboot ==="
run set_ip
- run getdtb rundtb bootfromnet ramparam addcons e1000para bootdtb
+ run getdtb rundtb bootfromnet ramparam addcons e1000para
addprofile bootdtb
else
echo "=== netboot failed ==="
fiMATRIX VISION GmbH, Talstrasse 16, DE-71570 Oppenweiler
Registergericht: Amtsgericht Stuttgart, HRB 271090
Geschiaeftsf?hrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner, Hans-Joachim Reich
PATCH 2/2 use common code for mvBC-P (MPC5200)
Dear =?ISO-8859-1?Q?Andr=E9?= Schwarz,
Quoted 5 lines · In message <1247836062.3953.61.camel@swa-m460> you wrote:
This patch makes use of common code, i.e. removes duplicate board specific code. Additionally some hard coded numbers have been replace by definitions and an configurable PCI latency has been added.
Quoted 8 lines
Signed-off-by Andr=C3=A9 Schwarz <[email protected]>---
board/matrix_vision/mvbc_p/mvbc_p.c | 94 +++++--------------------- board/matrix_vision/mvbc_p/mvbc_p.h | 2 +- board/matrix_vision/mvbc_p/mvbc_p_autoscript | 10 ++- 3 files changed, 24 insertions(+), 82 deletions(-)
Please merge this into the "add common code" patch.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de All a hacker needs is a tight PUSHJ, a loose pair of UUOs, and a warm place to shift.