OMAP3: PM: Wakeup from TWL4030 keypad with OFF mode
Subsystems (3)
PATCH 3/3 OMAP3: PM: Wakeup from TWL4030 keypad with OFF mode
This patch allows wakeup from TWL4030 keypad when
OFF mode is hit during suspend.
Tested on OMAP3EVM.
--- arch/arm/mach-omap2/board-omap3evm.c | 86 ++++++++++++++++++++++++++++++++++ 1 files changed, 86 insertions(+), 0 deletions(-)
arch/arm/mach-omap2/board-omap3evm.c +86 -0
@@ -40,12 +40,15 @@#include <plat/board.h> #include <plat/usb.h> #include <plat/common.h> +#include <plat/control.h> #include <plat/mcspi.h> #include "mux.h" #include "sdram-micron-mt46h32m32lf-6.h" #include "mmc-twl4030.h" +#include "prm-regbits-34xx.h" +#define OMAP3_EVM_TS_GPIO 175#define OMAP3_EVM_EHCI_VBUS 22#define OMAP3_EVM_EHCI_SELECT 61
@@ -218,6 +221,84 @@ static struct platform_device leds_gpio = { }, }; +#ifdef CONFIG_PM +/* +* Save the state of keypad +* +* TODO: This definition should ideally be in a header file, but +* matrix_keypad.h is not the right one. Also, plat/keypad.h +* is no longer used. +*/ +struct omap_keypad_pm_state { +void __iomem *wk_st; +void __iomem *wk_en; +u32 wk_mask; +u32 padconf; +}; + +/* +* Board specific hook for keypad suspend +*/ +void omap3_evm_kp_suspend (void *ptr) +{ +struct omap_keypad_pm_state *pstate = + (struct omap_keypad_pm_state *)ptr; + +if (pstate) { +/* +* Set wake-enable bit +*/ +if (pstate->wk_en && pstate->wk_mask) { +u32 v =__raw_readl (pstate->wk_en); + v |= pstate->wk_mask; +__raw_writel (v, pstate->wk_en); + } +/* +* Set corresponding IOPAD wakeup-enable +*/ +if (cpu_is_omap34xx () && pstate->padconf) { +u16 v =omap_ctrl_readw (pstate->padconf); + v |=OMAP3_PADCONF_WAKEUPENABLE0 ; +omap_ctrl_writew (v, pstate->padconf); + } + } +} + +/* +* Board specific hook for keypad resume +*/ +void omap3_evm_kp_resume (void *ptr) +{ +struct omap_keypad_pm_state *pstate = + (struct omap_keypad_pm_state *)ptr; + +if (pstate) { +/* +* Clear wake-enable bit +*/ +if (pstate->wk_en && pstate->wk_mask) { +u32 v =__raw_readl (pstate->wk_en); + v &= ~pstate->wk_mask; +__raw_writel (v, pstate->wk_en); + } +/* +* Clear corresponding IOPAD wakeup-enable +*/ +if (cpu_is_omap34xx () && pstate->padconf) { +u16 v =omap_ctrl_readw (pstate->padconf); + v &= ~OMAP3_PADCONF_WAKEUPENABLE0 ; +omap_ctrl_writew (v, pstate->padconf); + } + } +} + +static struct omap_keypad_pm_state omap3evm_kp_pm_state = { + .wk_st =OMAP34XX_PRM_REGADDR (WKUP_MOD ,PM_WKEN1 ), + .wk_en =OMAP34XX_PRM_REGADDR (WKUP_MOD ,PM_WKST1 ), + .wk_mask =OMAP3430_EN_GPIO1 , + .padconf =0x1e0 , +}; +#endif /* CONFIG_PM */ static int omap3evm_twl_gpio_setup (struct device *dev,unsigned gpio,unsigned ngpio)
@@ -288,6 +369,11 @@ static struct twl4030_keypad_data omap3evm_kp_data = { .rows = 4, .cols = 4, .rep = 1, +#ifdef CONFIG_PM + .pm_state = (void *)&omap3evm_kp_pm_state, + .on_suspend = omap3_evm_kp_suspend, + .on_resume = omap3_evm_kp_resume, +#endif /* CONFIG_PM */ };static struct twl4030_madc_platform_data omap3evm_madc_data = {
Signature · 1 line
1.6.2.2
Quoted 6 lines · Sanjeev Premi
This patch allows wakeup from TWL4030 keypad when
OFF mode is hit during suspend.Tested on OMAP3EVM.
Signed-off-by Sanjeev Premi <[email protected]>
The idea here looks good, but there is nothing realy EVM specific here AFAICT, and this exact code could be used on any other board using the T2 keypad, right? How about a common location?
Also, after looking at this patch, I think the 'void *pstate' member of struct twl4030_keypad_data should be renamed to 'void *data' to be more clear that it's just a pointer.
Kevin
Quoted 128 lines
--- arch/arm/mach-omap2/board-omap3evm.c | 86 ++++++++++++++++++++++++++++++++++ 1 files changed, 86 insertions(+), 0 deletions(-)arch/arm/mach-omap2/board-omap3evm.c +86
-0@@ -40,12 +40,15 @@#include <plat/board.h> #include <plat/usb.h> #include <plat/common.h> +#include <plat/control.h> #include <plat/mcspi.h> #include "mux.h" #include "sdram-micron-mt46h32m32lf-6.h" #include "mmc-twl4030.h" +#include "prm-regbits-34xx.h" +#define OMAP3_EVM_TS_GPIO 175#define OMAP3_EVM_EHCI_VBUS 22#define OMAP3_EVM_EHCI_SELECT 61@@ -218,6 +221,84 @@ static struct platform_device leds_gpio = { }, }; +#ifdef CONFIG_PM +/* +* Save the state of keypad +* +* TODO: This definition should ideally be in a header file, but +* matrix_keypad.h is not the right one. Also, plat/keypad.h +* is no longer used. +*/ +struct omap_keypad_pm_state { +void __iomem *wk_st; +void __iomem *wk_en; +u32 wk_mask; +u32 padconf; +}; + +/* +* Board specific hook for keypad suspend +*/ +void omap3_evm_kp_suspend (void *ptr) +{ +struct omap_keypad_pm_state *pstate = + (struct omap_keypad_pm_state *)ptr; + +if (pstate) { +/* +* Set wake-enable bit +*/ +if (pstate->wk_en && pstate->wk_mask) { +u32 v =__raw_readl (pstate->wk_en); + v |= pstate->wk_mask; +__raw_writel (v, pstate->wk_en); + } +/* +* Set corresponding IOPAD wakeup-enable +*/ +if (cpu_is_omap34xx () && pstate->padconf) { +u16 v =omap_ctrl_readw (pstate->padconf); + v |=OMAP3_PADCONF_WAKEUPENABLE0 ; +omap_ctrl_writew (v, pstate->padconf); + } + } +} + +/* +* Board specific hook for keypad resume +*/ +void omap3_evm_kp_resume (void *ptr) +{ +struct omap_keypad_pm_state *pstate = + (struct omap_keypad_pm_state *)ptr; + +if (pstate) { +/* +* Clear wake-enable bit +*/ +if (pstate->wk_en && pstate->wk_mask) { +u32 v =__raw_readl (pstate->wk_en); + v &= ~pstate->wk_mask; +__raw_writel (v, pstate->wk_en); + } +/* +* Clear corresponding IOPAD wakeup-enable +*/ +if (cpu_is_omap34xx () && pstate->padconf) { +u16 v =omap_ctrl_readw (pstate->padconf); + v &= ~OMAP3_PADCONF_WAKEUPENABLE0 ; +omap_ctrl_writew (v, pstate->padconf); + } + } +} + +static struct omap_keypad_pm_state omap3evm_kp_pm_state = { + .wk_st =OMAP34XX_PRM_REGADDR (WKUP_MOD ,PM_WKEN1 ), + .wk_en =OMAP34XX_PRM_REGADDR (WKUP_MOD ,PM_WKST1 ), + .wk_mask =OMAP3430_EN_GPIO1 , + .padconf =0x1e0 , +}; +#endif /* CONFIG_PM */ static int omap3evm_twl_gpio_setup (struct device *dev,unsigned gpio,unsigned ngpio)@@ -288,6 +369,11 @@ static struct twl4030_keypad_data omap3evm_kp_data = { .rows = 4, .cols = 4, .rep = 1, +#ifdef CONFIG_PM + .pm_state = (void *)&omap3evm_kp_pm_state, + .on_suspend = omap3_evm_kp_suspend, + .on_resume = omap3_evm_kp_resume, +#endif /* CONFIG_PM */ };static struct twl4030_madc_platform_data omap3evm_madc_data = {Signature · 6 lines
1.6.2.2 -- To unsubscribe from this list: send the line "unsubscribe linux-omap" in the body of a message to [email protected] More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoted 13 lines
-----Original Message-----
From: Kevin Hilman [mailto:[email protected]]
Sent: Friday, February 05, 2010 3:22 AM
To: Premi, Sanjeev
Cc: [email protected]
Subject: Re: [PATCH 3/3] OMAP3: PM: Wakeup from TWL4030 keypad with OFF modeQuoted 3 lines · Sanjeev Premi
This patch allows wakeup from TWL4030 keypad when
OFF mode is hit during suspend.
Quoted 7 lines
Quoted 3 lines
Tested on OMAP3EVM.
Signed-off-by Sanjeev Premi <[email protected]>The idea here looks good, but there is nothing realy EVM specific here AFAICT, and this exact code could be used on any other board using the T2 keypad, right? How about a common location?
[sp] The EVM uses SYS_NIRQ for hooking up with the T2 keypad. Not
sure of everyone would be doing so. Also, PADCONFs are more applicable for OMAP3, but T2 can be used with other processors as well...
I did initially inplement these functions in:
drivers/input/keyboard/twl4030_keypad.c
...but then moved to board specific file.
Quoted 4 lines
Also, after looking at this patch, I think the 'void *pstate' member of struct
twl4030_keypad_datashould be renamed to 'void *data' to be more clear that it's just a pointer.
[sp] Will make the change. However, will wait for your response on the
earlier comment before re-submit.
~sanjeev
Quoted 4 lines
Kevin
[snip]--[snip]
Quoted 26 lines · Sanjeev
Quoted 13 lines
-----Original Message-----
From: Kevin Hilman [mailto:[email protected]]
Sent: Friday, February 05, 2010 3:22 AM
To: Premi, Sanjeev
Cc: [email protected]
Subject: Re: [PATCH 3/3] OMAP3: PM: Wakeup from TWL4030 keypad with OFF modeQuoted 3 lines · Sanjeev Premi
This patch allows wakeup from TWL4030 keypad when
OFF mode is hit during suspend.Quoted 7 lines
Quoted 3 lines
Tested on OMAP3EVM.
Signed-off-by Sanjeev Premi <[email protected]>The idea here looks good, but there is nothing realy EVM specific here AFAICT, and this exact code could be used on any other board using the T2 keypad, right? How about a common location?
[sp] The EVM uses
SYS_NIRQfor hooking up with the T2 keypad. Not
sure of everyone would be doing so. Also, PADCONFs are more applicable for OMAP3, but T2 can be used with other processors as well...
Quoted 4 lines
I did initially inplement these functions in:
drivers/input/keyboard/twl4030_keypad.c...but then moved to board specific file.
I know at least SDP and EVM have these hooked up identically, so some common way to set them up would be preferred. Maybe a mach-omap2/t2-keypad.c that could be shared between various board files. The board files would still configure the IRQ line and the padconfs used.
Kevin
Quoted 16 lines
Quoted 4 lines
Also, after looking at this patch, I think the 'void *pstate' member of struct
twl4030_keypad_datashould be renamed to 'void *data' to be more clear that it's just a pointer.[sp] Will make the change. However, will wait for your response on the
earlier comment before re-submit.~sanjeev
Quoted 4 lines
Kevin
[snip]--[snip]
Quoted 44 lines
-----Original Message-----
From: Kevin Hilman [mailto:[email protected]]
Sent: Wednesday, February 17, 2010 4:24 AM
To: Premi, Sanjeev
Cc: [email protected]
Subject: Re: [PATCH 3/3] OMAP3: PM: Wakeup from TWL4030 keypad with OFF modeQuoted 10 lines · Sanjeev
Quoted 10 lines
-----Original Message-----
From: Kevin Hilman [mailto:[email protected]]
Sent: Friday, February 05, 2010 3:22 AM
To: Premi, Sanjeev
Cc: [email protected]
Subject: Re: [PATCH 3/3] OMAP3: PM: Wakeup from TWL4030 keypad with OFF modeSanjeev Premi <[email protected]> writes:
Quoted 8 lines
Quoted 8 lines
Quoted 6 lines
This patch allows wakeup from TWL4030 keypad when
OFF mode is hit during suspend.Tested on OMAP3EVM.
Signed-off-by Sanjeev Premi <[email protected]>The idea here looks good, but there is nothing realy EVM
specific here
Quoted 8 lines
Quoted 2 lines
AFAICT, and this exact code could be used on any other board using the T2 keypad, right? How about a common location?
[sp] The EVM uses
SYS_NIRQfor hooking up with the T2 keypad. Not
sure of everyone would be doing so. Also, PADCONFs are more applicable for OMAP3, but T2 can be used with other processors as well...Quoted 4 lines
I did initially inplement these functions in:
drivers/input/keyboard/twl4030_keypad.c...but then moved to board specific file.
Quoted 7 lines
I know at least SDP and EVM have these hooked up identically, so some common
way to set them up would be preferred. Maybe amach-omap2/t2-keypad.cthat
could be shared between various board files. The board files would still
configure the IRQ line and the padconfs used.
[sp] Yes. This can be done.
Best regards,
Sanjeev
Quoted 24 lines
Kevin
Quoted 2 lines
Quoted 2 lines
Also, after looking at this patch, I think the 'void
*pstate' member
Quoted 4 lines
Quoted 2 lines
of struct
twl4030_keypad_datashould be renamed to 'void *data' to be more clear that it's just a pointer.[sp] Will make the change. However, will wait for your
response on the
Quoted 10 lines
earlier comment before re-submit.
~sanjeev
Quoted 4 lines
Kevin
[snip]--[snip]