The zd1211rw does not work with the Shuttle PN15G (D-Link Corp. WL54). After the driver fails it also break the device for my windows XP install.
To get it back in working order I have to physically re-plug it while windows is running, this is pretty annoying as the PN15G is meant to be, and is, built inside my shuttle box.
I tried another device that uses the same driver, the ZyAIR G-220, and it works like a charm.
- Is there a way to get the Shuttle PN15G working ?
- Can prevent the driver from breaking my device, so it will remain working under windows XP.
Thijs van de Kraan
lsusb:
---------------
Bus 001 Device 004: ID 0586:3401 ZyXEL Communications Corp. ZyAIR G-220 Bus 001 Device 003: ID 07b8:6001 D-Link Corp. WL54
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 04fc:05d8 Sunplus Technology Co., Ltd Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
---------------
dmesg (Shuttle PN15G):
---------------
[ 9.419022] zd1211rw 1-8:1.0: phy0 [ 9.419050] usbcore: registered new interface driver zd1211rw [ 11.618783] usb 1-8: firmware: requesting zd1211/zd1211b_ub [ 11.979913] usb 1-8: firmware version 0x4810 and device bootcode version 0x4721 differ [ 11.979919] usb 1-8: firmware: requesting zd1211/zd1211b_ur [ 12.184918] usb 1-8: firmware: requesting zd1211/zd1211b_uphr [ 12.261522] zd1211rw 1-8:1.0: RF2959 is currently not supported for ZD1211B devices [ 12.263744] eth0: link down [ 12.263950] ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.491044] usb 1-8: firmware: requesting zd1211/zd1211b_ub [ 14.496834] usb 1-8: firmware version 0x4810 and device bootcode version 0x4721 differ [ 14.496841] usb 1-8: firmware: requesting zd1211/zd1211b_ur [ 15.526035] usb 1-8: USB control request for firmware upload failed. Error number -110 [ 15.526049] zd1211rw 1-8:1.0: couldn't load firmware. Error number
-110
dmesg (ZyAIR G-220):
---------------
[ 283.920025] usb 1-4: new high speed USB device using ehci_hcd and address 4 [ 284.070953] usb 1-4: configuration #1 chosen from 1 choice [ 284.200081] usb 1-4: reset high speed USB device using ehci_hcd and address 4 [ 284.351553] phy1: Selected rate control algorithm 'minstrel' [ 284.352966] zd1211rw 1-4:1.0: phy1 [ 284.387607] usb 1-4: firmware: requesting zd1211/zd1211_ub [ 284.422786] usb 1-4: firmware version 0x4330 and device bootcode version 0x4810 differ [ 284.422796] usb 1-4: firmware: requesting zd1211/zd1211_ur [ 284.446550] usb 1-4: firmware: requesting zd1211/zd1211_uphr [ 284.528039] zd1211rw 1-4:1.0: firmware version 4605 [ 284.568044] zd1211rw 1-4:1.0: zd1211 chip 0586:3401 v4810 high 00-13-49 AL2230_RF pa0 ----- [ 284.570691] cfg80211: Calling CRDA for country: DE [ 284.574176] cfg80211: Regulatory domain changed to country: DE [ 284.574184] (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 284.574190] (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 284.574195] (5150000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 284.574200] (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm) [ 284.589627] ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 291.145078] wlan1: authenticate with AP 00:21:29:8b:3a:49 [ 291.146703] wlan1: authenticated [ 291.146708] wlan1: associate with AP 00:21:29:8b:3a:49 [ 291.148944] wlan1: RX AssocResp from 00:21:29:8b:3a:49 (capab=0x411 status=0 aid=2) [ 291.148950] wlan1: associated [ 291.149928] ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 301.720021] wlan1: no IPv6 routers present
Quoted 30 lines · Thijs van der Kraan
The zd1211rw does not work with the Shuttle PN15G (D-Link Corp. WL54). After the driver fails it also break the device for my windows XP install.
To get it back in working order I have to physically re-plug it while windows is running, this is pretty annoying as the PN15G is meant to be, and is, built inside my shuttle box.I tried another device that uses the same driver, the ZyAIR G-220, and it works like a charm.
- Is there a way to get the Shuttle PN15G working ?
- Can prevent the driver from breaking my device, so it will remain working under windows XP.Thijs van de Kraan
lsusb:
---------------
Bus 001 Device 004: ID 0586:3401 ZyXEL Communications Corp. ZyAIR G-220 Bus 001 Device 003: ID 07b8:6001 D-Link Corp. WL54
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 004 Device 002: ID 04fc:05d8 Sunplus Technology Co., Ltd Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
---------------
Quoted 11 lines
dmesg (Shuttle PN15G):
---------------
[ 9.419022] zd1211rw 1-8:1.0: phy0
[ 9.419050] usbcore: registered new interface driver zd1211rw [ 11.618783] usb 1-8: firmware: requesting zd1211/zd1211b_ub [ 11.979913] usb 1-8: firmware version0x4810and device bootcode version0x4721differ
[ 11.979919] usb 1-8: firmware: requesting zd1211/zd1211b_ur [ 12.184918] usb 1-8: firmware: requesting zd1211/zd1211b_uphr [ 12.261522] zd1211rw 1-8:1.0: RF2959 is currently not supported for ZD1211B devices
Are you sure this is a ZD1211B, not a regular ZD1211? Try changing the USB ID definitions to mark this as a ZD1211.
Quoted 51 lines
[ 12.263744] eth0: link down
[ 12.263950]ADDRCONF(NETDEV_UP): eth0: link is not ready [ 14.491044] usb 1-8: firmware: requesting zd1211/zd1211b_ub [ 14.496834] usb 1-8: firmware version0x4810and device bootcode version0x4721differ
[ 14.496841] usb 1-8: firmware: requesting zd1211/zd1211b_ur [ 15.526035] usb 1-8: USB control request for firmware upload failed. Error number -110
[ 15.526049] zd1211rw 1-8:1.0: couldn't load firmware. Error number -110dmesg (ZyAIR G-220):
---------------[ 283.920025] usb 1-4: new high speed USB device using
ehci_hcdand address 4
[ 284.070953] usb 1-4: configuration #1 chosen from 1 choice [ 284.200081] usb 1-4: reset high speed USB device usingehci_hcdand address 4
[ 284.351553] phy1: Selected rate control algorithm 'minstrel' [ 284.352966] zd1211rw 1-4:1.0: phy1
[ 284.387607] usb 1-4: firmware: requesting zd1211/zd1211_ub [ 284.422786] usb 1-4: firmware version0x4330and device bootcode version0x4810differ
[ 284.422796] usb 1-4: firmware: requesting zd1211/zd1211_ur [ 284.446550] usb 1-4: firmware: requesting zd1211/zd1211_uphr [ 284.528039] zd1211rw 1-4:1.0: firmware version 4605
[ 284.568044] zd1211rw 1-4:1.0: zd1211 chip 0586:3401 v4810 high 00-13-49AL2230_RFpa0 -----
[ 284.570691] cfg80211: Calling CRDA for country: DE
[ 284.574176] cfg80211: Regulatory domain changed to country: DE [ 284.574184] (start_freq -end_freq@ bandwidth), (max_antenna_gain,max_eirp)
[ 284.574190] (2400000 KHz - 2483500 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 284.574195] (5150000 KHz - 5350000 KHz @ 40000 KHz), (N/A, 2000 mBm) [ 284.574200] (5470000 KHz - 5725000 KHz @ 40000 KHz), (N/A, 2698 mBm) [ 284.589627]ADDRCONF(NETDEV_UP): wlan1: link is not ready [ 291.145078] wlan1: authenticate with AP 00:21:29:8b:3a:49 [ 291.146703] wlan1: authenticated
[ 291.146708] wlan1: associate with AP 00:21:29:8b:3a:49
[ 291.148944] wlan1: RX AssocResp from 00:21:29:8b:3a:49 (capab=0x411 status=0 aid=2)
[ 291.148950] wlan1: associated
[ 291.149928]ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready [ 301.720021] wlan1: no IPv6 routers present--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Signature · 1 line
Vista: [V]iruses, [I]ntruders, [S]pyware, [T]rojans and [A]dware. :-)