ColdFire: Update processors' serial port configuration
PATCH 2/13 ColdFire: Update processors' serial port configuration
Provide parameter passing to uart_port_config(). Update port configuration - un-mask it before enable the bits.
Signed-off-by TsiChung Liew <[email protected]>
--- cpu/mcf5227x/cpu_init.c | 4 +- cpu/mcf523x/cpu_init.c | 26 +++++++++++++----- cpu/mcf52x2/cpu_init.c | 61 ++++++++++++++++++++++------------------- cpu/mcf532x/cpu_init.c | 29 ++++++++++++++----- cpu/mcf5445x/cpu_init.c | 32 +++++++++++++++++++--- cpu/mcf547x_8x/cpu_init.c | 4 +- include/asm-m68k/immap_5253.h | 1 + 7 files changed, 106 insertions(+), 51 deletions(-)
cpu/mcf5227x/cpu_init.c +2 -2
@@ -125,12 +125,12 @@ int cpu_init_r(void)return (0 ); } -void uart_port_conf (void ) +void uart_port_conf (int port) {volatile gpio_t *gpio = (gpio_t *)MMAP_GPIO ;/* Setup Ports: */ -switch (CONFIG_SYS_UART_PORT ) { +switch (port) {case 0 : gpio->par_uart &= (GPIO_PAR_UART_U0TXD_UNMASK &GPIO_PAR_UART_U0RXD_UNMASK );
cpu/mcf523x/cpu_init.c +19 -7
@@ -130,21 +130,32 @@ int cpu_init_r(void)return (0 ); } -void uart_port_conf (void ) +void uart_port_conf (int port) {volatile gpio_t *gpio = (gpio_t *)MMAP_GPIO ;/* Setup Ports: */ -switch (CONFIG_SYS_UART_PORT ) { +switch (port) {case 0 : - gpio->par_uart = (GPIO_PAR_UART_U0RXD |GPIO_PAR_UART_U0TXD ); + gpio->par_uart &= ~(GPIO_PAR_UART_U0RXD |GPIO_PAR_UART_U0TXD ); + gpio->par_uart |= (GPIO_PAR_UART_U0RXD |GPIO_PAR_UART_U0TXD );break ;case 1 : - gpio->par_uart = - (GPIO_PAR_UART_U1RXD_U1RXD |GPIO_PAR_UART_U1TXD_U1TXD ); + gpio->par_uart &= + ~(GPIO_PAR_UART_U1RXD_MASK |GPIO_PAR_UART_U1TXD_MASK ); + gpio->par_uart |= + (GPIO_PAR_UART_U1RXD_U1RXD |GPIO_PAR_UART_U1TXD_U1TXD );break ;case 2 : - gpio->par_timer = (GPIO_PAR_UART_U2RXD |GPIO_PAR_UART_U2TXD ); +#ifdef CONFIG_SYS_UART2_PRI_GPIO + gpio->par_uart &= ~(GPIO_PAR_UART_U2RXD |GPIO_PAR_UART_U2TXD ); + gpio->par_uart |= (GPIO_PAR_UART_U2RXD |GPIO_PAR_UART_U2TXD ); +#elif defined(CONFIG_SYS_UART2_ALT1_GPIO ) + gpio->feci2c &= + ~(GPIO_PAR_FECI2C_EMDC_MASK |GPIO_PAR_FECI2C_EMDIO_MASK ); + gpio->feci2c |= + (GPIO_PAR_FECI2C_EMDC_U2TXD |GPIO_PAR_FECI2C_EMDIO_U2RXD ); +#endif break ; } }
@@ -156,7 +167,8 @@ int fecpin_setclear(struct eth_device *dev, int setclear)if (setclear) { gpio->par_feci2c |= - (GPIO_PAR_FECI2C_EMDC_FECEMDC |GPIO_PAR_FECI2C_EMDIO_FECEMDIO ); + (GPIO_PAR_FECI2C_EMDC_FECEMDC | +GPIO_PAR_FECI2C_EMDIO_FECEMDIO ); }else { gpio->par_feci2c &= ~(GPIO_PAR_FECI2C_EMDC_MASK |GPIO_PAR_FECI2C_EMDIO_MASK );
cpu/mcf52x2/cpu_init.c +33 -28
136 lines not on this page · raw message
cpu/mcf532x/cpu_init.c +21 -8
@@ -133,19 +133,21 @@ int cpu_init_r(void)return (0 ); } -void uart_port_conf (void ) +void uart_port_conf (int port) {volatile gpio_t *gpio = (gpio_t *)MMAP_GPIO ;/* Setup Ports: */ -switch (CONFIG_SYS_UART_PORT ) { +switch (port) {case 0 : - gpio->par_uart = (GPIO_PAR_UART_U0TXD |GPIO_PAR_UART_U0RXD ); + gpio->par_uart &= ~(GPIO_PAR_UART_U0TXD |GPIO_PAR_UART_U0RXD ); + gpio->par_uart |= (GPIO_PAR_UART_U0TXD |GPIO_PAR_UART_U0RXD );break ;case 1 :#ifdef CONFIG_SYS_UART1_ALT1_GPIO gpio->par_simp1h &= - ~(GPIO_PAR_SIMP1H_DATA1_UNMASK |GPIO_PAR_SIMP1H_VEN1_UNMASK ); + ~(GPIO_PAR_SIMP1H_DATA1_UNMASK | +GPIO_PAR_SIMP1H_VEN1_UNMASK ); gpio->par_simp1h |= (GPIO_PAR_SIMP1H_DATA1_U1TXD |GPIO_PAR_SIMP1H_VEN1_U1RXD );#elif defined(CONFIG_SYS_UART1_ALT2_GPIO )
@@ -297,22 +299,33 @@ int cpu_init_r(void)return (0 ); } -void uart_port_conf (void ) +void uart_port_conf (int port) {volatile gpio_t *gpio = (gpio_t *)MMAP_GPIO ;/* Setup Ports: */ -switch (CONFIG_SYS_UART_PORT ) { +switch (port) {case 0 : - gpio->par_uart = (GPIO_PAR_UART_TXD0 |GPIO_PAR_UART_RXD0 ); + gpio->par_uart &= ~(GPIO_PAR_UART_TXD0 |GPIO_PAR_UART_RXD0 ); + gpio->par_uart |= (GPIO_PAR_UART_TXD0 |GPIO_PAR_UART_RXD0 );break ;case 1 : - gpio->par_uart = + gpio->par_uart &= + ~(GPIO_PAR_UART_TXD1 (3 ) |GPIO_PAR_UART_RXD1 (3 )); + gpio->par_uart |= (GPIO_PAR_UART_TXD1 (3 ) |GPIO_PAR_UART_RXD1 (3 ));break ;case 2 : +#ifdef CONFIG_SYS_UART2_ALT1_GPIO gpio->par_timer &=0x0F ; gpio->par_timer |= (GPIO_PAR_TIN3_URXD2 |GPIO_PAR_TIN2_UTXD2 ); +#elif defined(CONFIG_SYS_UART2_ALT2_GPIO ) + gpio->par_feci2c &=0xFF00 ; + gpio->par_feci2c |= (GPIO_PAR_FECI2C_SCL_UTXD2 |GPIO_PAR_FECI2C_SDA_URXD2 ); +#elif defined(CONFIG_SYS_UART2_ALT3_GPIO ) + gpio->par_ssi &=0xF0FF ; + gpio->par_ssi |= (GPIO_PAR_SSI_RXD (2 ) |GPIO_PAR_SSI_TXD (2 )); +#endif break ; } }
cpu/mcf5445x/cpu_init.c +28 -4
@@ -128,19 +128,43 @@ int cpu_init_r(void)return (0 ); } -void uart_port_conf (void ) +void uart_port_conf (int port) {volatile gpio_t *gpio = (gpio_t *)MMAP_GPIO ;/* Setup Ports: */ -switch (CONFIG_SYS_UART_PORT ) { +switch (port) {case 0 : - gpio->par_uart = + gpio->par_uart &= + ~(GPIO_PAR_UART_U0TXD_U0TXD |GPIO_PAR_UART_U0RXD_U0RXD ); + gpio->par_uart |= (GPIO_PAR_UART_U0TXD_U0TXD |GPIO_PAR_UART_U0RXD_U0RXD );break ;case 1 : - gpio->par_uart = +#ifdef CONFIG_SYS_UART1_PRI_GPIO + gpio->par_uart &= + ~(GPIO_PAR_UART_U1TXD_U1TXD |GPIO_PAR_UART_U1RXD_U1RXD ); + gpio->par_uart |= (GPIO_PAR_UART_U1TXD_U1TXD |GPIO_PAR_UART_U1RXD_U1RXD ); +#elif defined(CONFIG_SYS_UART1_ALT1_GPIO ) + gpio->par_ssi &= + (GPIO_PAR_SSI_SRXD_UNMASK |GPIO_PAR_SSI_STXD_UNMASK ); + gpio->par_ssi |= + (GPIO_PAR_SSI_SRXD_U1RXD |GPIO_PAR_SSI_STXD_U1TXD ); +#endif +break ; +case 2 : +#if defined(CONFIG_SYS_UART2_ALT1_GPIO ) + gpio->par_timer &= + (GPIO_PAR_TIMER_T3IN_UNMASK |GPIO_PAR_TIMER_T2IN_UNMASK ); + gpio->par_timer |= + (GPIO_PAR_TIMER_T3IN_U2RXD |GPIO_PAR_TIMER_T2IN_U2TXD ); +#elif defined(CONFIG_SYS_UART2_ALT2_GPIO ) + gpio->par_timer &= + (GPIO_PAR_FECI2C_SCL_UNMASK |GPIO_PAR_FECI2C_SDA_UNMASK ); + gpio->par_timer |= + (GPIO_PAR_FECI2C_SCL_U2TXD |GPIO_PAR_FECI2C_SDA_U2RXD ); +#endif break ; } }
cpu/mcf547x_8x/cpu_init.c +2 -2
@@ -113,13 +113,13 @@ int cpu_init_r(void)return (0 ); } -void uart_port_conf (void ) +void uart_port_conf (int port) {volatile gpio_t *gpio = (gpio_t *)MMAP_GPIO ;volatile u8 *pscsicr = (u8 *) (CONFIG_SYS_UART_BASE +0x40 );/* Setup Ports: */ -switch (CONFIG_SYS_UART_PORT ) { +switch (port) {case 0 : gpio->par_psc0 = (GPIO_PAR_PSC0_TXD0 |GPIO_PAR_PSC0_RXD0 );break ;
include/asm-m68k/immap_5253.h +1 -0
@@ -37,6 +37,7 @@#define MMAP_CAN0 (CONFIG_SYS_MBAR + 0x00010000)#define MMAP_CAN1 (CONFIG_SYS_MBAR + 0x00011000) +#define MMAP_PAR (CONFIG_SYS_MBAR2 + 0x0000019C)#define MMAP_I2C1 (CONFIG_SYS_MBAR2 + 0x00000440)#define MMAP_UART2 (CONFIG_SYS_MBAR2 + 0x00000C00)
Signature · 1 line
1.6.2.5