ColdFire: M5271EVB DRAM Bring up issue
PATCH 6/13 ColdFire: M5271EVB DRAM Bring up issue
Fix proper portsize: The register for portsize is either 00b, 01b, or 1xb. The value that previous assigned is 32d.
Fix DRAM bring up: insert asm("nop") for every DRAM register setup
Signed-off-by TsiChung Liew <[email protected]>
--- board/freescale/m5271evb/m5271evb.c | 12 ++++++++++-- 1 files changed, 10 insertions(+), 2 deletions(-)
board/freescale/m5271evb/m5271evb.c +10 -2
@@ -47,6 +47,7 @@ phys_size_t initdram (int board_type) {MCF_GPIO_SDRAM_SDWE |MCF_GPIO_SDRAM_SCAS |MCF_GPIO_SDRAM_SRAS |MCF_GPIO_SDRAM_SCKE | MCF_GPIO_SDRAM_SDCS_11); + asm(" nop" );/* * Check to see if the SDRAM has already been initialized
@@ -55,8 +56,9 @@ phys_size_t initdram (int board_type) {if (!(mbar_readLong (MCF_SDRAMC_DACR0 ) & MCF_SDRAMC_DACRn_RE)) {/* Initialize DRAM Control Register: DCR */ mbar_writeShort (MCF_SDRAMC_DCR , -MCF_SDRAMC_DCR_RTIM (0x01 ) - |MCF_SDRAMC_DCR_RC (0x30 )); +MCF_SDRAMC_DCR_RTIM (2 ) + |MCF_SDRAMC_DCR_RC (0x2E )); + asm(" nop" );/* * Initialize DACR0
@@ -70,15 +72,18 @@ phys_size_t initdram (int board_type) { | MCF_SDRAMC_DACRn_CASL(1) |MCF_SDRAMC_DACRn_CBM (3 ) | MCF_SDRAMC_DACRn_PS(0)); + asm(" nop" );/* Initialize DMR0 */ mbar_writeLong (MCF_SDRAMC_DMR0 , MCF_SDRAMC_DMRn_BAM_16M | MCF_SDRAMC_DMRn_V); + asm(" nop" );/* Set IP bit in DACR */ mbar_writeLong (MCF_SDRAMC_DACR0 ,mbar_readLong (MCF_SDRAMC_DACR0 ) | MCF_SDRAMC_DACRn_IP); + asm(" nop" );/* Wait at least 20ns to allow banks to precharge */ for (i =0 ; i <5 ; i++)
@@ -86,6 +91,7 @@ phys_size_t initdram (int board_type) {/* Write to this block to initiate precharge */ *(u32 *)(CONFIG_SYS_SDRAM_BASE ) =0xa5a5a5a5 ; + asm(" nop" );/* Set RE bit in DACR */ mbar_writeLong(MCF_SDRAMC_DACR0, mbar_readLong(MCF_SDRAMC_DACR0)
@@ -98,6 +104,7 @@ phys_size_t initdram (int board_type) {/* Finish the configuration by issuing the MRS */ mbar_writeLong (MCF_SDRAMC_DACR0 ,mbar_readLong (MCF_SDRAMC_DACR0 ) | MCF_SDRAMC_DACRn_MRS); + asm(" nop" );/* * Write to the SDRAM Mode Register A0-A11 = 0x400
@@ -109,6 +116,7 @@ phys_size_t initdram (int board_type) {* Burst Length = 1 */ *(u32 *)(CONFIG_SYS_SDRAM_BASE +0x400 ) =0xa5a5a5a5 ; + asm(" nop" ); }return CONFIG_SYS_SDRAM_SIZE *1024 *1024 ;
Signature · 1 line
1.6.2.5