[PATCH 0/3} hwmon: Driver for SMM665 Six-Channel Active DC Output Controller/Monitor
Subsystems (2)
This driver adds support for the hardware monitoring features of the Summit Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
Issues/questions/notes:
- Some of the command register enum values are currently unused. Keep or remove ?
- Critical voltage values are not supported by the current sysfs API, though available from the chip. Would it make sense to report those values, e.g. as inX_min_crit and inX_max_crit ?
Note: This also applies to PMBus chips, so the question will come up again.
- It would be nice to be able to support other variants of this chip, but I have no means to test it. Some test coverage by others would be helpful.
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
PATCH 1/3 hwmon: Driver for SMM665 Six-Channel Active DC Output Controller/Monitor
This driver adds support for the monitoring features of the Summit Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
--- drivers/hwmon/Kconfig | 12 + drivers/hwmon/Makefile | 1 + drivers/hwmon/smm665.c | 739 ++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 752 insertions(+), 0 deletions(-) create mode 100644 drivers/hwmon/smm665.c
drivers/hwmon/Kconfig +12 -0
@@ -739,6 +739,18 @@ config SENSORS_SIS5595 This driver can also be built as a module. If so, the module will be called sis5595. +config SENSORS_SMM665 + tristate "Summit Microelectronics SMM665" + depends on I2C && EXPERIMENTAL + default n + help + If you say yes here you get support for the hardware monitoring + features of the Summit Microelectronics SMM665 Six-Channel + Active DC Output Controller / Monitor. + + This driver can also be built as a module. If so, the module will + be called smm665. + config SENSORS_DME1737 tristate "SMSC DME1737, SCH311x and compatibles" depends on I2C && EXPERIMENTAL
drivers/hwmon/Makefile +1 -0
@@ -76,6 +76,7 @@ obj-$(CONFIG_SENSORS_LM93) += lm93.o obj-$(CONFIG_SENSORS_LM95241) += lm95241.o obj-$(CONFIG_SENSORS_LTC4215) += ltc4215.o obj-$(CONFIG_SENSORS_LTC4245) += ltc4245.o +obj-$(CONFIG_SENSORS_SMM665) += smm665.o obj-$(CONFIG_SENSORS_MAX1111) += max1111.o obj-$(CONFIG_SENSORS_MAX1619) += max1619.o obj-$(CONFIG_SENSORS_MAX6650) += max6650.o
drivers/hwmon/smm665.c new file +739 -0
739 lines not on this page · raw message
Signature · 7 lines
1.7.0.87.g0901d _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [PATCH 1/3] hwmon: Driver for SMM665 Six-Channel Active DC Output Controller/Monitor
Hi,
I've taken a quick look through this code.
One or two specific comments below.
Only big question is why have the limit functionality in this driver? Given the device has no hardware support and you don't have any form of regular polling (I think) then these limits will only be noticed if you query them. Hence why not leave this job to userspace?
I'm not saying you are wrong to do this. Just that you need to explain your reasoning alongside the patch.
Quoted 69 lines · Guenter Roeck
This driver adds support for the monitoring features of the Summit Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
Signed-off-by Guenter Roeck <[email protected]>--- drivers/hwmon/Kconfig | 12 + drivers/hwmon/Makefile | 1 + drivers/hwmon/smm665.c | 739 ++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 752 insertions(+), 0 deletions(-) create mode 100644 drivers/hwmon/smm665.cdrivers/hwmon/Kconfig +12
-0@@ -739,6 +739,18 @@ config SENSORS_SIS5595 This driver can also be built as a module. If so, the module will be called sis5595. +config SENSORS_SMM665 + tristate "Summit Microelectronics SMM665" + depends on I2C && EXPERIMENTAL + default n + help + If you say yes here you get support for the hardware monitoring + features of the Summit Microelectronics SMM665 Six-Channel + Active DC Output Controller / Monitor. + + This driver can also be built as a module. If so, the module will + be called smm665. + config SENSORS_DME1737 tristate "SMSC DME1737, SCH311x and compatibles" depends on I2C && EXPERIMENTALdrivers/hwmon/Makefile +1
-0@@ -76,6 +76,7 @@ obj-$(CONFIG_SENSORS_LM93) += lm93.o obj-$(CONFIG_SENSORS_LM95241) += lm95241.o obj-$(CONFIG_SENSORS_LTC4215) += ltc4215.o obj-$(CONFIG_SENSORS_LTC4245) += ltc4245.o +obj-$(CONFIG_SENSORS_SMM665) += smm665.o obj-$(CONFIG_SENSORS_MAX1111) += max1111.o obj-$(CONFIG_SENSORS_MAX1619) += max1619.o obj-$(CONFIG_SENSORS_MAX6650) += max6650.odrivers/hwmon/smm665.c new file +17
-0@@ -0,0 +1,739 @@ +/* +* Driver for SMM665 Power Controller / Monitor +* +* Copyright (C) 2010 Ericsson AB. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; version 2 of the License. +* +* This driver should with no or minor modifications also work for SMM766, +* SMM764, and SMM465. Only monitoring functionality is implemented. +* +* Datasheets: +* http://www.summitmicro.com/prod_select/summary/SMM665/SMM665B_2089_20.pdf +* http://www.summitmicro.com/prod_select/summary/SMM766B/SMM766B_2122.pdf +*/ +
drivers/hwmon/smm665.c line 27
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/delay.h> +
Personally I'd be more inclined to do these as a whole lot of '#define's. You never use the enum type for anything so why bother?
Quoted 71 lines
drivers/hwmon/smm665.c new file +71
-0+/* ADC channel addresses */ +enum smm665_adcregs { +SMM665_MISC16_ADC_DATA_A =0x00 , +SMM665_MISC16_ADC_DATA_B =0x01 , +SMM665_MISC16_ADC_DATA_C =0x02 , +SMM665_MISC16_ADC_DATA_D =0x03 , +SMM665_MISC16_ADC_DATA_E =0x04 , +SMM665_MISC16_ADC_DATA_F =0x05 , +SMM665_MISC16_ADC_DATA_VDD =0x06 , +SMM665_MISC16_ADC_DATA_12V =0x07 , +SMM665_MISC16_ADC_DATA_INT_TEMP =0x08 , +SMM665_MISC16_ADC_DATA_AIN1 =0x09 , +SMM665_MISC16_ADC_DATA_AIN2 =0x0a , +}; + +enum smm665_cmdregs { +SMM665_MISC8_CMD_STS =0x80 , +SMM665_MISC8_STATUS1 =0x81 , +SMM665_MISC8_STATUSS2 =0x82 , +SMM665_MISC8_IO_POLARITY =0x83 , +SMM665_MISC8_PUP_POLARITY =0x84 , +SMM665_MISC8_ADOC_STATUS1 =0x85 , +SMM665_MISC8_ADOC_STATUS2 =0x86 , +SMM665_MISC8_WRITE_PROT =0x87 , +SMM665_MISC8_STS_TRACK =0x88 , +}; + +/* +* Configuration registers and register groups +*/ +#define SMM665_ADOC_ENABLE 0x0d +#define SMM665_LIMIT_BASE 0x80 + +/* +* Limit register bit masks +*/ +#define SMM665_TRIGGER_RST 0x8000 +#define SMM665_TRIGGER_HEALTHY 0x4000 +#define SMM665_TRIGGER_POWEROFF 0x2000 +#define SMM665_TRIGGER_SHUTDOWN 0x1000 +#define SMM665_ADC_MASK 0x03ff + +#define smm665_is_critical (lim) ((lim) & (SMM665_TRIGGER_RST \ + | SMM665_TRIGGER_POWEROFF \ + | SMM665_TRIGGER_SHUTDOWN)) +/* +* Fault register bit definitions +* Values are merged from status registers 1/2, +* with status register 1 providing the upper 8 bits. +*/ +#define SMM665_FAULT_A 0x0001 +#define SMM665_FAULT_B 0x0002 +#define SMM665_FAULT_C 0x0004 +#define SMM665_FAULT_D 0x0008 +#define SMM665_FAULT_E 0x0010 +#define SMM665_FAULT_F 0x0020 +#define SMM665_FAULT_VDD 0x0040 +#define SMM665_FAULT_12V 0x0080 +#define SMM665_FAULT_TEMP 0x0100 +#define SMM665_FAULT_AIN1 0x0200 +#define SMM665_FAULT_AIN2 0x0400 + +/* +* I2C Register addresses +* +* The configuration register needs to be the configured base register. +* The command/status register address is derived from it. +*/ +#define SMM665_REGMASK 0x78 +#define SMM665_CMDREG_BASE 0x48 +#define SMM665_CONFREG_BASE 0x50
drivers/hwmon/smm665.c line 108
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+ +/* Internal reference voltage (VREF, x 1000 */ +#define SMM665_VREF_ADC_X1000 1250 + +/* +* Equations given by chip manufacturer to calculate voltage/temperature values +* vref = Reference voltage on VREF_ADC pin +* adc = 10bit ADC value read back from registers +*/ +
I guess these are handy if you ever intend to allow different reference voltages, but right now they add code and reduce readability. Obviously leave be if the intent is add that vref control in a later patch!
Quoted 17 lines
drivers/hwmon/smm665.c new file +17
-0+/* Voltage A-F and VDD */ +#define SMM665_VMON_ADC_TO_VOLTS (vref, adc) ((adc) * (vref) / 256) + +/* Voltage 12VIN */ +#define SMM665_12VIN_ADC_TO_VOLTS (vref, adc) ((adc) * (vref) * 3 / 256) + +/* Voltage AIN1, AIN2 */ +#define SMM665_AIN_ADC_TO_VOLTS (vref, adc) ((adc) * (vref) / 512) + +/* Temp Sensor */ +#define SMM665_TEMP_ADC_TO_CELSIUS (adc) ((adc) <= 511) ? \ + ((int)(adc) * 1000 / 4) : \ + (((int)(adc) - 0x400) * 1000 / 4) + +#define SMM665_NUM_ADC 11 +#define SMM665_ADC_RETRIES 5 +#define SMM665_ADC_WAIT 100/* conversion time is 70 uS for SMM665B,
drivers/hwmon/smm665.c line 135
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+182 uS for SMM766 */ + +struct smm665_data { +struct device *hwmon_dev; + +struct mutex update_lock; +bool valid; +unsigned long last_updated;/* in jiffies */ +u16 adc[SMM665_NUM_ADC ];/* adc values (raw) */ +u16 faults;/* fault status */
Given these aren't used often, I'd prefer more meaningful variable names.
Quoted 25 lines
drivers/hwmon/smm665.c new file +25
-0+int cu[SMM665_NUM_ADC ];/* critical under limit (converted) */ +int au[SMM665_NUM_ADC ];/* alarm under limit (converted) */ +int co[SMM665_NUM_ADC ];/* critical over limit (converted) */ +int ao[SMM665_NUM_ADC ];/* alarm over limit (converted) */ +struct i2c_client *cmdreg; +}; + +/* +* smm665_read16() +* +* Read 16 bit value from <reg>, <reg+1>. Upper 8 bits are in <reg>. +*/ +static int smm665_read16 (struct i2c_client *client,int reg) +{ +int rv, val; + + rv =i2c_smbus_read_byte_data (client, reg); +if (rv <0 ) +return rv; + val = rv <<8 ; + rv =i2c_smbus_read_byte_data (client, reg +1 ); +if (rv <0 ) +return rv; + val |= rv; +return val;
drivers/hwmon/smm665.c line 170
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+} + +/* +* Read adc value. +*/ +static int smm665_read_adc (struct i2c_client *client,int adc) +{ +int rv =-1 ; +int retries; +
Why the retries? If there is a reason for this to sometimes fail, please add a comment explaining what it is! If it is a hardware bug, then tell us!
Quoted 6 lines
drivers/hwmon/smm665.c new file +6
-0+for (retries =0 ; retries <SMM665_ADC_RETRIES ; retries++) { +int radc; + +/* +* Algorithm for reading ADC, per SMM665 datasheet +*
drivers/hwmon/smm665.c line 186
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+* {[S][addr][W][Ack]} {[offset][Ack]} {[S][addr][R][Nack]} +* [wait 70 uS] +* {[S][addr][R][Ack]} {[datahi][Ack]} {[datalo][Ack][P]} +* +* To implement the first part of this exchange, +* do a full read transaction and expect a failure/Nack. +* This sets up the address pointer on the SMM665 +* and starts the ADC conversion. +* Then do a two-byte read transaction. +*/
Is there no better way of handling this? There are protocol mangling hacks to tell the i2c core to ignore a NAKs under some circumstances.
Quoted 20 lines
drivers/hwmon/smm665.c new file +20
-0+ rv =i2c_smbus_read_byte_data (client, adc <<3 ); +if (rv >=0 ) { +/* No error, something is wrong. Retry. */ + rv =-1 ; +continue ; + } +udelay (SMM665_ADC_WAIT ); +/* +* Now read two bytes. +* +* Neither i2c_smbus_read_byte() nor +* i2c_smbus_read_block_data() worked here, +* so use i2c_smbus_read_word_data() instead. +* We could also try to use i2c_master_recv(), +* but that is not always supported. +*/ + rv =i2c_smbus_read_word_data (client,0 ); +if (rv <0 ) +continue ; +/*
drivers/hwmon/smm665.c line 216
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+* Validate/verify readback adc channel (in bit 11..14) +* High byte is in lower 8 bit of rv, so only shift by 3. +*/ + radc = (rv >>3 ) &0x0f ; +if (radc != adc) { + rv =-1 ; +continue ; + } + +/* Byte order is reversed, need to swap. */
Isn't this endian dependent?
Quoted 106 lines
drivers/hwmon/smm665.c new file +106
-0+ rv =swab16 (rv) &SMM665_ADC_MASK ; +break ; + } +return rv; +} + +static struct smm665_data *smm665_update_device (struct device *dev) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client); + +mutex_lock (&data->update_lock); + +if (time_after (jiffies, data->last_updated +HZ ) || !data->valid) { +int i, faults; + +/* +* read status registers +*/ + faults =smm665_read16 (client,SMM665_MISC8_STATUS1 ); +if (unlikely (faults <0 )) + data->faults =0 ; +else + data->faults = faults; + +/* Read adc registers */ +for (i =0 ; i <SMM665_NUM_ADC ; i++) { +int val =smm665_read_adc (data->cmdreg, i); +if (unlikely (val <0 )) + data->adc[i] =0 ; +else + data->adc[i] = val; + } + + data->last_updated = jiffies; + data->valid =1 ; + } + +mutex_unlock (&data->update_lock); + +return data; +} + +/* Return converted value from given adc */ +static int smm665_convert (u16 adcval,int index) +{ +int val =0 ; + +switch (index) { +case SMM665_MISC16_ADC_DATA_12V : + val =SMM665_12VIN_ADC_TO_VOLTS (SMM665_VREF_ADC_X1000 , + adcval &SMM665_ADC_MASK ); +break ; + +case SMM665_MISC16_ADC_DATA_VDD : +case SMM665_MISC16_ADC_DATA_A : +case SMM665_MISC16_ADC_DATA_B : +case SMM665_MISC16_ADC_DATA_C : +case SMM665_MISC16_ADC_DATA_D : +case SMM665_MISC16_ADC_DATA_E : +case SMM665_MISC16_ADC_DATA_F : + val =SMM665_VMON_ADC_TO_VOLTS (SMM665_VREF_ADC_X1000 , + adcval &SMM665_ADC_MASK ); +break ; + +case SMM665_MISC16_ADC_DATA_AIN1 : +case SMM665_MISC16_ADC_DATA_AIN2 : + val =SMM665_AIN_ADC_TO_VOLTS (SMM665_VREF_ADC_X1000 , + adcval &SMM665_ADC_MASK ); +break ; + +case SMM665_MISC16_ADC_DATA_INT_TEMP : + val =SMM665_TEMP_ADC_TO_CELSIUS (adcval &SMM665_ADC_MASK ); +break ; + +default : +/* If we get here, the developer messed up */ +WARN_ON_ONCE (1 ); +break ; + } + +return val; +} + +/* Return converted value from given adc */ +static int smm665_get_input (struct device *dev,int adc) +{ +struct smm665_data *data =smm665_update_device (dev); + +return smm665_convert (data->adc[adc], adc); +} + +static int smm665_get_min (struct device *dev,int index) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client); + +return data->au[index]; +} + +static int smm665_get_max (struct device *dev,int index) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client); + +return data->ao[index];
drivers/hwmon/smm665.c line 332
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+} + +static int smm665_get_crit (struct device *dev,int index) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client); + +return data->co[index]; +} +
I'm confused. So these alarms are purely software constructs. Given I don't think the device does regular polling, why not leave this to userspace?
drivers/hwmon/smm665.c line 343
Quoted 11 lines
drivers/hwmon/smm665.c new file +11
-0+static int smm665_get_min_alarm (struct device *dev,int index) +{ +struct smm665_data *data =smm665_update_device (dev); +int val =smm665_convert (data->adc[index], index); + +/* +* Look for lower alarm limit. Report alarm if the current +* adc value is equal to or lower than the specified limit. +*/ +if (val <= data->au[index]) +return 1 ;
(nitpick) Inconsistent spacing between this and the next function.
Quoted 259 lines
drivers/hwmon/smm665.c new file +259
-0+return 0 ; +} + +static int smm665_get_max_alarm (struct device *dev,int index) +{ +struct smm665_data *data =smm665_update_device (dev); +int val =smm665_convert (data->adc[index], index); + +/* +* Look for upper alarm limit. Report alarm if the current +* adc value is equal to or larger than the specified limit. +*/ +if (val >= data->ao[index]) +return 1 ; + +return 0 ; +} + +static int smm665_get_fault (struct device *dev,int index) +{ +struct smm665_data *data =smm665_update_device (dev); + +if (data->faults & (1 << index)) +return 1 ; + +return 0 ; +} + +#define SMM665_SHOW (what) \ + static ssize_t smm665_show_##what(struct device *dev, \ + struct device_attribute *da, char *buf) \ +{ \ + struct sensor_device_attribute *attr = to_sensor_dev_attr(da); \ + const int val = smm665_get_##what(dev, attr->index); \ + return snprintf(buf, PAGE_SIZE, "%d\n", val); \ +} + +SMM665_SHOW (input); +SMM665_SHOW (min); +SMM665_SHOW (max); +SMM665_SHOW (crit); +SMM665_SHOW (fault); +SMM665_SHOW (min_alarm); +SMM665_SHOW (max_alarm); + +/* These macros are used below in constructing device attribute objects +* for use with sysfs_create_group() to make a sysfs device file +* for each register. +*/ + +#define SMM665_ATTR (name, type, cmd_idx) \ + static SENSOR_DEVICE_ATTR(name##_##type, S_IRUGO, \ + smm665_show_##type, NULL, cmd_idx) + +/* Construct a sensor_device_attribute structure for each register */ + +/* Input voltages */ +SMM665_ATTR (in1, input,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, input,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, input,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, input,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, input,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, input,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, input,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, input,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, input,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, input,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltages min */ +SMM665_ATTR (in1, min,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, min,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, min,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, min,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, min,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, min,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, min,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, min,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, min,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, min,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltages max */ +SMM665_ATTR (in1, max,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, max,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, max,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, max,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, max,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, max,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, max,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, max,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, max,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, max,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltage min alarms */ +SMM665_ATTR (in1, min_alarm,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, min_alarm,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, min_alarm,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, min_alarm,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, min_alarm,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, min_alarm,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, min_alarm,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, min_alarm,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, min_alarm,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, min_alarm,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltage max alarms */ +SMM665_ATTR (in1, max_alarm,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, max_alarm,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, max_alarm,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, max_alarm,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, max_alarm,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, max_alarm,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, max_alarm,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, max_alarm,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, max_alarm,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, max_alarm,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Faults */ +SMM665_ATTR (in1, fault,SMM665_FAULT_12V ); +SMM665_ATTR (in2, fault,SMM665_FAULT_VDD ); +SMM665_ATTR (in3, fault,SMM665_FAULT_A ); +SMM665_ATTR (in4, fault,SMM665_FAULT_B ); +SMM665_ATTR (in5, fault,SMM665_FAULT_C ); +SMM665_ATTR (in6, fault,SMM665_FAULT_D ); +SMM665_ATTR (in7, fault,SMM665_FAULT_E ); +SMM665_ATTR (in8, fault,SMM665_FAULT_F ); +SMM665_ATTR (in9, fault,SMM665_FAULT_AIN1 ); +SMM665_ATTR (in10, fault,SMM665_FAULT_AIN2 ); + +/* Temperature */ +SMM665_ATTR (temp1, input,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, min,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, max,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, crit,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, min_alarm,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, max_alarm,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, fault,SMM665_FAULT_TEMP ); + +/* +* Finally, construct an array of pointers to members of the above objects, +* as required for sysfs_create_group() +*/ +static struct attribute *smm665_attributes[] = { + &sensor_dev_attr_in1_input.dev_attr.attr, + &sensor_dev_attr_in1_min.dev_attr.attr, + &sensor_dev_attr_in1_max.dev_attr.attr, + &sensor_dev_attr_in1_min_alarm.dev_attr.attr, + &sensor_dev_attr_in1_max_alarm.dev_attr.attr, + &sensor_dev_attr_in1_fault.dev_attr.attr, + + &sensor_dev_attr_in2_input.dev_attr.attr, + &sensor_dev_attr_in2_min.dev_attr.attr, + &sensor_dev_attr_in2_max.dev_attr.attr, + &sensor_dev_attr_in2_min_alarm.dev_attr.attr, + &sensor_dev_attr_in2_max_alarm.dev_attr.attr, + &sensor_dev_attr_in2_fault.dev_attr.attr, + + &sensor_dev_attr_in3_input.dev_attr.attr, + &sensor_dev_attr_in3_min.dev_attr.attr, + &sensor_dev_attr_in3_max.dev_attr.attr, + &sensor_dev_attr_in3_min_alarm.dev_attr.attr, + &sensor_dev_attr_in3_max_alarm.dev_attr.attr, + &sensor_dev_attr_in3_fault.dev_attr.attr, + + &sensor_dev_attr_in4_input.dev_attr.attr, + &sensor_dev_attr_in4_min.dev_attr.attr, + &sensor_dev_attr_in4_max.dev_attr.attr, + &sensor_dev_attr_in4_min_alarm.dev_attr.attr, + &sensor_dev_attr_in4_max_alarm.dev_attr.attr, + &sensor_dev_attr_in4_fault.dev_attr.attr, + + &sensor_dev_attr_in5_input.dev_attr.attr, + &sensor_dev_attr_in5_min.dev_attr.attr, + &sensor_dev_attr_in5_max.dev_attr.attr, + &sensor_dev_attr_in5_min_alarm.dev_attr.attr, + &sensor_dev_attr_in5_max_alarm.dev_attr.attr, + &sensor_dev_attr_in5_fault.dev_attr.attr, + + &sensor_dev_attr_in6_input.dev_attr.attr, + &sensor_dev_attr_in6_min.dev_attr.attr, + &sensor_dev_attr_in6_max.dev_attr.attr, + &sensor_dev_attr_in6_min_alarm.dev_attr.attr, + &sensor_dev_attr_in6_max_alarm.dev_attr.attr, + &sensor_dev_attr_in6_fault.dev_attr.attr, + + &sensor_dev_attr_in7_input.dev_attr.attr, + &sensor_dev_attr_in7_min.dev_attr.attr, + &sensor_dev_attr_in7_max.dev_attr.attr, + &sensor_dev_attr_in7_min_alarm.dev_attr.attr, + &sensor_dev_attr_in7_max_alarm.dev_attr.attr, + &sensor_dev_attr_in7_fault.dev_attr.attr, + + &sensor_dev_attr_in8_input.dev_attr.attr, + &sensor_dev_attr_in8_min.dev_attr.attr, + &sensor_dev_attr_in8_max.dev_attr.attr, + &sensor_dev_attr_in8_min_alarm.dev_attr.attr, + &sensor_dev_attr_in8_max_alarm.dev_attr.attr, + &sensor_dev_attr_in8_fault.dev_attr.attr, + + &sensor_dev_attr_in9_input.dev_attr.attr, + &sensor_dev_attr_in9_min.dev_attr.attr, + &sensor_dev_attr_in9_max.dev_attr.attr, + &sensor_dev_attr_in9_min_alarm.dev_attr.attr, + &sensor_dev_attr_in9_max_alarm.dev_attr.attr, + &sensor_dev_attr_in9_fault.dev_attr.attr, + + &sensor_dev_attr_in10_input.dev_attr.attr, + &sensor_dev_attr_in10_min.dev_attr.attr, + &sensor_dev_attr_in10_max.dev_attr.attr, + &sensor_dev_attr_in10_min_alarm.dev_attr.attr, + &sensor_dev_attr_in10_max_alarm.dev_attr.attr, + &sensor_dev_attr_in10_fault.dev_attr.attr, + + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_temp1_min.dev_attr.attr, + &sensor_dev_attr_temp1_max.dev_attr.attr, + &sensor_dev_attr_temp1_crit.dev_attr.attr, + &sensor_dev_attr_temp1_min_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_max_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_fault.dev_attr.attr, + +NULL , +}; + +static const struct attribute_group smm665_group = { + .attrs = smm665_attributes, +}; + +static int smm665_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +struct i2c_adapter *adapter = client->adapter; +struct smm665_data *data; +int i, ret; + +if (!i2c_check_functionality (adapter,I2C_FUNC_SMBUS_BYTE_DATA + |I2C_FUNC_SMBUS_WORD_DATA )) +return -ENODEV ; + +if (i2c_smbus_read_byte_data (client,SMM665_ADOC_ENABLE ) <0 ) +return -ENODEV ; + + data =kzalloc (sizeof (*data),GFP_KERNEL ); +if (!data) { + ret = -ENOMEM ; + goto out_kzalloc; + } + +i2c_set_clientdata (client, data); +mutex_init (&data->update_lock); + + data->cmdreg =i2c_new_dummy (adapter, (client->addr & ~SMM665_REGMASK ) + |SMM665_CMDREG_BASE ); +if (!data->cmdreg) { + ret = -ENOMEM ; + goto out_new_dummy; + } +if (i2c_smbus_read_byte_data (data->cmdreg,SMM665_MISC8_CMD_STS ) <0 ) { + ret = -ENODEV ; + goto out_sysfs_create_group;
drivers/hwmon/smm665.c line 612
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+ } + +/* +* Read limits. +* +* Limit registers start with register SMM665_LIMIT_BASE. +* Each channel uses 8 registers, providing four limit values +* per channel. +* +* Available limits from chip registers, per channel:
A simple statement of endianess and number of bytes would do the job.
Quoted 84 lines
drivers/hwmon/smm665.c new file +84
-0+* u1: under limit 1 +* u2: under limit 2 +* o1: over limit 1 +* o2: over limit 2 +* +* Register address offsets: +* +0: u1[h] +* +1: u1[l] +* +2: u2[h] +* +3: u2[l] +* +4: o1[h] +* +5: o1[l] +* +6: o2[h] +* +7: o2[l] +* +* Limit register order is as defined with smm665_adcregs, +* so we use smm665_adcregs values throughout the code to index +* limit registers. +* +* We save the first retrieved value both as "critical" and "alarm" +* value. The second value overwrites either the critical or the +* alarm value, depending on its configuration. This ensures that both +* critical and alarm values are initialized, even if both registers are +* configured as critical or non-critical. +* +* Note: Critical values for voltage channels are saved, even though +* this information is currently not used by the driver. This is mostly +* for consistency, though it might eventually be useful if future APIs +* support reporting "critical" voltage values. +*/ + ret = -ENODEV ; +for (i =0 ; i <SMM665_NUM_ADC ; i++) { +int val; + + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; + data->cu[i] = data->au[i] =smm665_convert (val, i); + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 +2 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; +if (smm665_is_critical (val)) + data->cu[i] =smm665_convert (val, i); +else + data->au[i] =smm665_convert (val, i); + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 +4 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; + data->co[i] = data->ao[i] =smm665_convert (val, i); + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 +6 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; +if (smm665_is_critical (val)) + data->co[i] =smm665_convert (val, i); +else + data->ao[i] =smm665_convert (val, i); + } + +/* Register sysfs hooks */ + ret =sysfs_create_group (&client->dev.kobj, &smm665_group); +if (ret) + goto out_sysfs_create_group; + + data->hwmon_dev =hwmon_device_register (&client->dev); +if (IS_ERR (data->hwmon_dev)) { + ret =PTR_ERR (data->hwmon_dev); + goto out_hwmon_device_register; + } + +return 0 ; + +out_hwmon_device_register: +sysfs_remove_group (&client->dev.kobj, &smm665_group); +out_sysfs_create_group: +i2c_unregister_device (data->cmdreg); +out_new_dummy: +kfree (data); +out_kzalloc: +return ret; +} + +static int smm665_remove (struct i2c_client *client) +{ +struct smm665_data *data =i2c_get_clientdata (client);
drivers/hwmon/smm665.c line 706
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+ +i2c_unregister_device (data->cmdreg); +hwmon_device_unregister (data->hwmon_dev); +sysfs_remove_group (&client->dev.kobj, &smm665_group); + +kfree (data); + +return 0 ; +} +
Personally I'd be cynical. If the other devices you list above should work. I'd add them to the id table and Kconfig description and just put a note saying they are untested.
Obviously don't do this if you have any reason to suspect they are not fully compatible.
But then that is me :)
Quoted 23 lines
drivers/hwmon/smm665.c new file +23
-0+static const struct i2c_device_id smm665_id[] = { + {"smm665" ,0 }, + {} +}; + +MODULE_DEVICE_TABLE (i2c, smm665_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver smm665_driver = { + .driver = { + .name ="smm665" , + }, + .probe = smm665_probe, + .remove = smm665_remove, + .id_table = smm665_id, +}; + +static int __init smm665_init (void ) +{ +return i2c_add_driver (&smm665_driver); +} + +static void __exit smm665_exit(void)
drivers/hwmon/smm665.c line 739
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+{ +i2c_del_driver (&smm665_driver); +} + +MODULE_AUTHOR ("Guenter Roeck" ); +MODULE_DESCRIPTION ("SMM665 driver" ); +MODULE_LICENSE ("GPL" ); + +module_init (smm665_init); +module_exit (smm665_exit);
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [lm-sensors] [PATCH 1/3] hwmon: Driver for SMM665 Six-Channel Active DC Output Controller/Monitor
Quoted 7 lines · Jonathan Cameron
Hi,
I've taken a quick look through this code.
One or two specific comments below.
Quoted 7 lines
Only big question is why have the limit functionality in this driver? Given the device has no hardware support and you don't have any form of regular polling (I think) then these limits will only be noticed if you query them. Hence why not leave this job to userspace?
I'm not saying you are wrong to do this. Just that you need to explain your reasoning alongside the patch.
Another quick query. Are the _min / _max attributes as defined in the abi meant for alarms? I always thought they were to tell userspace the limits on measurement?
Either way, one of us has misunderstood so perhaps the documentation needs to be more specific....
Quoted 825 lines · Guenter Roeck
Quoted 69 lines
This driver adds support for the monitoring features of the Summit Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
Signed-off-by Guenter Roeck <[email protected]>--- drivers/hwmon/Kconfig | 12 + drivers/hwmon/Makefile | 1 + drivers/hwmon/smm665.c | 739 ++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 752 insertions(+), 0 deletions(-) create mode 100644 drivers/hwmon/smm665.cdrivers/hwmon/Kconfig +12
-0@@ -739,6 +739,18 @@ config SENSORS_SIS5595 This driver can also be built as a module. If so, the module will be called sis5595. +config SENSORS_SMM665 + tristate "Summit Microelectronics SMM665" + depends on I2C && EXPERIMENTAL + default n + help + If you say yes here you get support for the hardware monitoring + features of the Summit Microelectronics SMM665 Six-Channel + Active DC Output Controller / Monitor. + + This driver can also be built as a module. If so, the module will + be called smm665. + config SENSORS_DME1737 tristate "SMSC DME1737, SCH311x and compatibles" depends on I2C && EXPERIMENTALdrivers/hwmon/Makefile +1
-0@@ -76,6 +76,7 @@ obj-$(CONFIG_SENSORS_LM93) += lm93.o obj-$(CONFIG_SENSORS_LM95241) += lm95241.o obj-$(CONFIG_SENSORS_LTC4215) += ltc4215.o obj-$(CONFIG_SENSORS_LTC4245) += ltc4245.o +obj-$(CONFIG_SENSORS_SMM665) += smm665.o obj-$(CONFIG_SENSORS_MAX1111) += max1111.o obj-$(CONFIG_SENSORS_MAX1619) += max1619.o obj-$(CONFIG_SENSORS_MAX6650) += max6650.odrivers/hwmon/smm665.c new file +17
-0@@ -0,0 +1,739 @@ +/* +* Driver for SMM665 Power Controller / Monitor +* +* Copyright (C) 2010 Ericsson AB. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; version 2 of the License. +* +* This driver should with no or minor modifications also work for SMM766, +* SMM764, and SMM465. Only monitoring functionality is implemented. +* +* Datasheets: +* http://www.summitmicro.com/prod_select/summary/SMM665/SMM665B_2089_20.pdf +* http://www.summitmicro.com/prod_select/summary/SMM766B/SMM766B_2122.pdf +*/ +drivers/hwmon/smm665.c line 27
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/i2c.h> +#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/delay.h> +Personally I'd be more inclined to do these as a whole lot of '#define's. You never use the enum type for anything so why bother?
Quoted 71 lines
drivers/hwmon/smm665.c new file +71
-0+/* ADC channel addresses */ +enum smm665_adcregs { +SMM665_MISC16_ADC_DATA_A =0x00 , +SMM665_MISC16_ADC_DATA_B =0x01 , +SMM665_MISC16_ADC_DATA_C =0x02 , +SMM665_MISC16_ADC_DATA_D =0x03 , +SMM665_MISC16_ADC_DATA_E =0x04 , +SMM665_MISC16_ADC_DATA_F =0x05 , +SMM665_MISC16_ADC_DATA_VDD =0x06 , +SMM665_MISC16_ADC_DATA_12V =0x07 , +SMM665_MISC16_ADC_DATA_INT_TEMP =0x08 , +SMM665_MISC16_ADC_DATA_AIN1 =0x09 , +SMM665_MISC16_ADC_DATA_AIN2 =0x0a , +}; + +enum smm665_cmdregs { +SMM665_MISC8_CMD_STS =0x80 , +SMM665_MISC8_STATUS1 =0x81 , +SMM665_MISC8_STATUSS2 =0x82 , +SMM665_MISC8_IO_POLARITY =0x83 , +SMM665_MISC8_PUP_POLARITY =0x84 , +SMM665_MISC8_ADOC_STATUS1 =0x85 , +SMM665_MISC8_ADOC_STATUS2 =0x86 , +SMM665_MISC8_WRITE_PROT =0x87 , +SMM665_MISC8_STS_TRACK =0x88 , +}; + +/* +* Configuration registers and register groups +*/ +#define SMM665_ADOC_ENABLE 0x0d +#define SMM665_LIMIT_BASE 0x80 + +/* +* Limit register bit masks +*/ +#define SMM665_TRIGGER_RST 0x8000 +#define SMM665_TRIGGER_HEALTHY 0x4000 +#define SMM665_TRIGGER_POWEROFF 0x2000 +#define SMM665_TRIGGER_SHUTDOWN 0x1000 +#define SMM665_ADC_MASK 0x03ff + +#define smm665_is_critical (lim) ((lim) & (SMM665_TRIGGER_RST \ + | SMM665_TRIGGER_POWEROFF \ + | SMM665_TRIGGER_SHUTDOWN)) +/* +* Fault register bit definitions +* Values are merged from status registers 1/2, +* with status register 1 providing the upper 8 bits. +*/ +#define SMM665_FAULT_A 0x0001 +#define SMM665_FAULT_B 0x0002 +#define SMM665_FAULT_C 0x0004 +#define SMM665_FAULT_D 0x0008 +#define SMM665_FAULT_E 0x0010 +#define SMM665_FAULT_F 0x0020 +#define SMM665_FAULT_VDD 0x0040 +#define SMM665_FAULT_12V 0x0080 +#define SMM665_FAULT_TEMP 0x0100 +#define SMM665_FAULT_AIN1 0x0200 +#define SMM665_FAULT_AIN2 0x0400 + +/* +* I2C Register addresses +* +* The configuration register needs to be the configured base register. +* The command/status register address is derived from it. +*/ +#define SMM665_REGMASK 0x78 +#define SMM665_CMDREG_BASE 0x48 +#define SMM665_CONFREG_BASE 0x50drivers/hwmon/smm665.c line 108
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+ +/* Internal reference voltage (VREF, x 1000 */ +#define SMM665_VREF_ADC_X1000 1250 + +/* +* Equations given by chip manufacturer to calculate voltage/temperature values +* vref = Reference voltage on VREF_ADC pin +* adc = 10bit ADC value read back from registers +*/ +I guess these are handy if you ever intend to allow different reference voltages, but right now they add code and reduce readability. Obviously leave be if the intent is add that vref control in a later patch!
Quoted 17 lines
drivers/hwmon/smm665.c new file +17
-0+/* Voltage A-F and VDD */ +#define SMM665_VMON_ADC_TO_VOLTS (vref, adc) ((adc) * (vref) / 256) + +/* Voltage 12VIN */ +#define SMM665_12VIN_ADC_TO_VOLTS (vref, adc) ((adc) * (vref) * 3 / 256) + +/* Voltage AIN1, AIN2 */ +#define SMM665_AIN_ADC_TO_VOLTS (vref, adc) ((adc) * (vref) / 512) + +/* Temp Sensor */ +#define SMM665_TEMP_ADC_TO_CELSIUS (adc) ((adc) <= 511) ? \ + ((int)(adc) * 1000 / 4) : \ + (((int)(adc) - 0x400) * 1000 / 4) + +#define SMM665_NUM_ADC 11 +#define SMM665_ADC_RETRIES 5 +#define SMM665_ADC_WAIT 100/* conversion time is 70 uS for SMM665B, drivers/hwmon/smm665.c line 135
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+182 uS for SMM766 */ + +struct smm665_data { +struct device *hwmon_dev; + +struct mutex update_lock; +bool valid; +unsigned long last_updated;/* in jiffies */ +u16 adc[SMM665_NUM_ADC ];/* adc values (raw) */ +u16 faults;/* fault status */ Given these aren't used often, I'd prefer more meaningful variable names.
Quoted 25 lines
drivers/hwmon/smm665.c new file +25
-0+int cu[SMM665_NUM_ADC ];/* critical under limit (converted) */ +int au[SMM665_NUM_ADC ];/* alarm under limit (converted) */ +int co[SMM665_NUM_ADC ];/* critical over limit (converted) */ +int ao[SMM665_NUM_ADC ];/* alarm over limit (converted) */ +struct i2c_client *cmdreg; +}; + +/* +* smm665_read16() +* +* Read 16 bit value from <reg>, <reg+1>. Upper 8 bits are in <reg>. +*/ +static int smm665_read16 (struct i2c_client *client,int reg) +{ +int rv, val; + + rv =i2c_smbus_read_byte_data (client, reg); +if (rv <0 ) +return rv; + val = rv <<8 ; + rv =i2c_smbus_read_byte_data (client, reg +1 ); +if (rv <0 ) +return rv; + val |= rv; +return val;drivers/hwmon/smm665.c line 170
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+} + +/* +* Read adc value. +*/ +static int smm665_read_adc (struct i2c_client *client,int adc) +{ +int rv =-1 ; +int retries; +Why the retries? If there is a reason for this to sometimes fail, please add a comment explaining what it is! If it is a hardware bug, then tell us!
Quoted 6 lines
drivers/hwmon/smm665.c new file +6
-0+for (retries =0 ; retries <SMM665_ADC_RETRIES ; retries++) { +int radc; + +/* +* Algorithm for reading ADC, per SMM665 datasheet +* drivers/hwmon/smm665.c line 186
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+* {[S][addr][W][Ack]} {[offset][Ack]} {[S][addr][R][Nack]} +* [wait 70 uS] +* {[S][addr][R][Ack]} {[datahi][Ack]} {[datalo][Ack][P]} +* +* To implement the first part of this exchange, +* do a full read transaction and expect a failure/Nack. +* This sets up the address pointer on the SMM665 +* and starts the ADC conversion. +* Then do a two-byte read transaction. +*/ Is there no better way of handling this? There are protocol mangling hacks to tell the i2c core to ignore a NAKs under some circumstances.
Quoted 20 lines
drivers/hwmon/smm665.c new file +20
-0+ rv =i2c_smbus_read_byte_data (client, adc <<3 ); +if (rv >=0 ) { +/* No error, something is wrong. Retry. */ + rv =-1 ; +continue ; + } +udelay (SMM665_ADC_WAIT ); +/* +* Now read two bytes. +* +* Neither i2c_smbus_read_byte() nor +* i2c_smbus_read_block_data() worked here, +* so use i2c_smbus_read_word_data() instead. +* We could also try to use i2c_master_recv(), +* but that is not always supported. +*/ + rv =i2c_smbus_read_word_data (client,0 ); +if (rv <0 ) +continue ; +/* drivers/hwmon/smm665.c line 216
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+* Validate/verify readback adc channel (in bit 11..14) +* High byte is in lower 8 bit of rv, so only shift by 3. +*/ + radc = (rv >>3 ) &0x0f ; +if (radc != adc) { + rv =-1 ; +continue ; + } + +/* Byte order is reversed, need to swap. */ Isn't this endian dependent?
Quoted 106 lines
drivers/hwmon/smm665.c new file +106
-0+ rv =swab16 (rv) &SMM665_ADC_MASK ; +break ; + } +return rv; +} + +static struct smm665_data *smm665_update_device (struct device *dev) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client); + +mutex_lock (&data->update_lock); + +if (time_after (jiffies, data->last_updated +HZ ) || !data->valid) { +int i, faults; + +/* +* read status registers +*/ + faults =smm665_read16 (client,SMM665_MISC8_STATUS1 ); +if (unlikely (faults <0 )) + data->faults =0 ; +else + data->faults = faults; + +/* Read adc registers */ +for (i =0 ; i <SMM665_NUM_ADC ; i++) { +int val =smm665_read_adc (data->cmdreg, i); +if (unlikely (val <0 )) + data->adc[i] =0 ; +else + data->adc[i] = val; + } + + data->last_updated = jiffies; + data->valid =1 ; + } + +mutex_unlock (&data->update_lock); + +return data; +} + +/* Return converted value from given adc */ +static int smm665_convert (u16 adcval,int index) +{ +int val =0 ; + +switch (index) { +case SMM665_MISC16_ADC_DATA_12V : + val =SMM665_12VIN_ADC_TO_VOLTS (SMM665_VREF_ADC_X1000 , + adcval &SMM665_ADC_MASK ); +break ; + +case SMM665_MISC16_ADC_DATA_VDD : +case SMM665_MISC16_ADC_DATA_A : +case SMM665_MISC16_ADC_DATA_B : +case SMM665_MISC16_ADC_DATA_C : +case SMM665_MISC16_ADC_DATA_D : +case SMM665_MISC16_ADC_DATA_E : +case SMM665_MISC16_ADC_DATA_F : + val =SMM665_VMON_ADC_TO_VOLTS (SMM665_VREF_ADC_X1000 , + adcval &SMM665_ADC_MASK ); +break ; + +case SMM665_MISC16_ADC_DATA_AIN1 : +case SMM665_MISC16_ADC_DATA_AIN2 : + val =SMM665_AIN_ADC_TO_VOLTS (SMM665_VREF_ADC_X1000 , + adcval &SMM665_ADC_MASK ); +break ; + +case SMM665_MISC16_ADC_DATA_INT_TEMP : + val =SMM665_TEMP_ADC_TO_CELSIUS (adcval &SMM665_ADC_MASK ); +break ; + +default : +/* If we get here, the developer messed up */ +WARN_ON_ONCE (1 ); +break ; + } + +return val; +} + +/* Return converted value from given adc */ +static int smm665_get_input (struct device *dev,int adc) +{ +struct smm665_data *data =smm665_update_device (dev); + +return smm665_convert (data->adc[adc], adc); +} + +static int smm665_get_min (struct device *dev,int index) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client); + +return data->au[index]; +} + +static int smm665_get_max (struct device *dev,int index) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client); + +return data->ao[index];drivers/hwmon/smm665.c line 332
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+} + +static int smm665_get_crit (struct device *dev,int index) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client); + +return data->co[index]; +} +I'm confused. So these alarms are purely software constructs. Given I don't think the device does regular polling, why not leave this to userspace?
drivers/hwmon/smm665.c line 343
Quoted 11 lines
drivers/hwmon/smm665.c new file +11
-0+static int smm665_get_min_alarm (struct device *dev,int index) +{ +struct smm665_data *data =smm665_update_device (dev); +int val =smm665_convert (data->adc[index], index); + +/* +* Look for lower alarm limit. Report alarm if the current +* adc value is equal to or lower than the specified limit. +*/ +if (val <= data->au[index]) +return 1 ;(nitpick) Inconsistent spacing between this and the next function.
Quoted 259 lines
drivers/hwmon/smm665.c new file +259
-0+return 0 ; +} + +static int smm665_get_max_alarm (struct device *dev,int index) +{ +struct smm665_data *data =smm665_update_device (dev); +int val =smm665_convert (data->adc[index], index); + +/* +* Look for upper alarm limit. Report alarm if the current +* adc value is equal to or larger than the specified limit. +*/ +if (val >= data->ao[index]) +return 1 ; + +return 0 ; +} + +static int smm665_get_fault (struct device *dev,int index) +{ +struct smm665_data *data =smm665_update_device (dev); + +if (data->faults & (1 << index)) +return 1 ; + +return 0 ; +} + +#define SMM665_SHOW (what) \ + static ssize_t smm665_show_##what(struct device *dev, \ + struct device_attribute *da, char *buf) \ +{ \ + struct sensor_device_attribute *attr = to_sensor_dev_attr(da); \ + const int val = smm665_get_##what(dev, attr->index); \ + return snprintf(buf, PAGE_SIZE, "%d\n", val); \ +} + +SMM665_SHOW (input); +SMM665_SHOW (min); +SMM665_SHOW (max); +SMM665_SHOW (crit); +SMM665_SHOW (fault); +SMM665_SHOW (min_alarm); +SMM665_SHOW (max_alarm); + +/* These macros are used below in constructing device attribute objects +* for use with sysfs_create_group() to make a sysfs device file +* for each register. +*/ + +#define SMM665_ATTR (name, type, cmd_idx) \ + static SENSOR_DEVICE_ATTR(name##_##type, S_IRUGO, \ + smm665_show_##type, NULL, cmd_idx) + +/* Construct a sensor_device_attribute structure for each register */ + +/* Input voltages */ +SMM665_ATTR (in1, input,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, input,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, input,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, input,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, input,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, input,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, input,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, input,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, input,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, input,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltages min */ +SMM665_ATTR (in1, min,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, min,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, min,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, min,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, min,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, min,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, min,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, min,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, min,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, min,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltages max */ +SMM665_ATTR (in1, max,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, max,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, max,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, max,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, max,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, max,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, max,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, max,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, max,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, max,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltage min alarms */ +SMM665_ATTR (in1, min_alarm,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, min_alarm,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, min_alarm,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, min_alarm,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, min_alarm,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, min_alarm,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, min_alarm,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, min_alarm,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, min_alarm,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, min_alarm,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltage max alarms */ +SMM665_ATTR (in1, max_alarm,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, max_alarm,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, max_alarm,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, max_alarm,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, max_alarm,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, max_alarm,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, max_alarm,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, max_alarm,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, max_alarm,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, max_alarm,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Faults */ +SMM665_ATTR (in1, fault,SMM665_FAULT_12V ); +SMM665_ATTR (in2, fault,SMM665_FAULT_VDD ); +SMM665_ATTR (in3, fault,SMM665_FAULT_A ); +SMM665_ATTR (in4, fault,SMM665_FAULT_B ); +SMM665_ATTR (in5, fault,SMM665_FAULT_C ); +SMM665_ATTR (in6, fault,SMM665_FAULT_D ); +SMM665_ATTR (in7, fault,SMM665_FAULT_E ); +SMM665_ATTR (in8, fault,SMM665_FAULT_F ); +SMM665_ATTR (in9, fault,SMM665_FAULT_AIN1 ); +SMM665_ATTR (in10, fault,SMM665_FAULT_AIN2 ); + +/* Temperature */ +SMM665_ATTR (temp1, input,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, min,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, max,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, crit,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, min_alarm,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, max_alarm,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, fault,SMM665_FAULT_TEMP ); + +/* +* Finally, construct an array of pointers to members of the above objects, +* as required for sysfs_create_group() +*/ +static struct attribute *smm665_attributes[] = { + &sensor_dev_attr_in1_input.dev_attr.attr, + &sensor_dev_attr_in1_min.dev_attr.attr, + &sensor_dev_attr_in1_max.dev_attr.attr, + &sensor_dev_attr_in1_min_alarm.dev_attr.attr, + &sensor_dev_attr_in1_max_alarm.dev_attr.attr, + &sensor_dev_attr_in1_fault.dev_attr.attr, + + &sensor_dev_attr_in2_input.dev_attr.attr, + &sensor_dev_attr_in2_min.dev_attr.attr, + &sensor_dev_attr_in2_max.dev_attr.attr, + &sensor_dev_attr_in2_min_alarm.dev_attr.attr, + &sensor_dev_attr_in2_max_alarm.dev_attr.attr, + &sensor_dev_attr_in2_fault.dev_attr.attr, + + &sensor_dev_attr_in3_input.dev_attr.attr, + &sensor_dev_attr_in3_min.dev_attr.attr, + &sensor_dev_attr_in3_max.dev_attr.attr, + &sensor_dev_attr_in3_min_alarm.dev_attr.attr, + &sensor_dev_attr_in3_max_alarm.dev_attr.attr, + &sensor_dev_attr_in3_fault.dev_attr.attr, + + &sensor_dev_attr_in4_input.dev_attr.attr, + &sensor_dev_attr_in4_min.dev_attr.attr, + &sensor_dev_attr_in4_max.dev_attr.attr, + &sensor_dev_attr_in4_min_alarm.dev_attr.attr, + &sensor_dev_attr_in4_max_alarm.dev_attr.attr, + &sensor_dev_attr_in4_fault.dev_attr.attr, + + &sensor_dev_attr_in5_input.dev_attr.attr, + &sensor_dev_attr_in5_min.dev_attr.attr, + &sensor_dev_attr_in5_max.dev_attr.attr, + &sensor_dev_attr_in5_min_alarm.dev_attr.attr, + &sensor_dev_attr_in5_max_alarm.dev_attr.attr, + &sensor_dev_attr_in5_fault.dev_attr.attr, + + &sensor_dev_attr_in6_input.dev_attr.attr, + &sensor_dev_attr_in6_min.dev_attr.attr, + &sensor_dev_attr_in6_max.dev_attr.attr, + &sensor_dev_attr_in6_min_alarm.dev_attr.attr, + &sensor_dev_attr_in6_max_alarm.dev_attr.attr, + &sensor_dev_attr_in6_fault.dev_attr.attr, + + &sensor_dev_attr_in7_input.dev_attr.attr, + &sensor_dev_attr_in7_min.dev_attr.attr, + &sensor_dev_attr_in7_max.dev_attr.attr, + &sensor_dev_attr_in7_min_alarm.dev_attr.attr, + &sensor_dev_attr_in7_max_alarm.dev_attr.attr, + &sensor_dev_attr_in7_fault.dev_attr.attr, + + &sensor_dev_attr_in8_input.dev_attr.attr, + &sensor_dev_attr_in8_min.dev_attr.attr, + &sensor_dev_attr_in8_max.dev_attr.attr, + &sensor_dev_attr_in8_min_alarm.dev_attr.attr, + &sensor_dev_attr_in8_max_alarm.dev_attr.attr, + &sensor_dev_attr_in8_fault.dev_attr.attr, + + &sensor_dev_attr_in9_input.dev_attr.attr, + &sensor_dev_attr_in9_min.dev_attr.attr, + &sensor_dev_attr_in9_max.dev_attr.attr, + &sensor_dev_attr_in9_min_alarm.dev_attr.attr, + &sensor_dev_attr_in9_max_alarm.dev_attr.attr, + &sensor_dev_attr_in9_fault.dev_attr.attr, + + &sensor_dev_attr_in10_input.dev_attr.attr, + &sensor_dev_attr_in10_min.dev_attr.attr, + &sensor_dev_attr_in10_max.dev_attr.attr, + &sensor_dev_attr_in10_min_alarm.dev_attr.attr, + &sensor_dev_attr_in10_max_alarm.dev_attr.attr, + &sensor_dev_attr_in10_fault.dev_attr.attr, + + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_temp1_min.dev_attr.attr, + &sensor_dev_attr_temp1_max.dev_attr.attr, + &sensor_dev_attr_temp1_crit.dev_attr.attr, + &sensor_dev_attr_temp1_min_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_max_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_fault.dev_attr.attr, + +NULL , +}; + +static const struct attribute_group smm665_group = { + .attrs = smm665_attributes, +}; + +static int smm665_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +struct i2c_adapter *adapter = client->adapter; +struct smm665_data *data; +int i, ret; + +if (!i2c_check_functionality (adapter,I2C_FUNC_SMBUS_BYTE_DATA + |I2C_FUNC_SMBUS_WORD_DATA )) +return -ENODEV ; + +if (i2c_smbus_read_byte_data (client,SMM665_ADOC_ENABLE ) <0 ) +return -ENODEV ; + + data =kzalloc (sizeof (*data),GFP_KERNEL ); +if (!data) { + ret = -ENOMEM ; + goto out_kzalloc; + } + +i2c_set_clientdata (client, data); +mutex_init (&data->update_lock); + + data->cmdreg =i2c_new_dummy (adapter, (client->addr & ~SMM665_REGMASK ) + |SMM665_CMDREG_BASE ); +if (!data->cmdreg) { + ret = -ENOMEM ; + goto out_new_dummy; + } +if (i2c_smbus_read_byte_data (data->cmdreg,SMM665_MISC8_CMD_STS ) <0 ) { + ret = -ENODEV ; + goto out_sysfs_create_group;drivers/hwmon/smm665.c line 612
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+ } + +/* +* Read limits. +* +* Limit registers start with register SMM665_LIMIT_BASE. +* Each channel uses 8 registers, providing four limit values +* per channel. +* +* Available limits from chip registers, per channel: A simple statement of endianess and number of bytes would do the job.
Quoted 84 lines
drivers/hwmon/smm665.c new file +84
-0+* u1: under limit 1 +* u2: under limit 2 +* o1: over limit 1 +* o2: over limit 2 +* +* Register address offsets: +* +0: u1[h] +* +1: u1[l] +* +2: u2[h] +* +3: u2[l] +* +4: o1[h] +* +5: o1[l] +* +6: o2[h] +* +7: o2[l] +* +* Limit register order is as defined with smm665_adcregs, +* so we use smm665_adcregs values throughout the code to index +* limit registers. +* +* We save the first retrieved value both as "critical" and "alarm" +* value. The second value overwrites either the critical or the +* alarm value, depending on its configuration. This ensures that both +* critical and alarm values are initialized, even if both registers are +* configured as critical or non-critical. +* +* Note: Critical values for voltage channels are saved, even though +* this information is currently not used by the driver. This is mostly +* for consistency, though it might eventually be useful if future APIs +* support reporting "critical" voltage values. +*/ + ret = -ENODEV ; +for (i =0 ; i <SMM665_NUM_ADC ; i++) { +int val; + + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; + data->cu[i] = data->au[i] =smm665_convert (val, i); + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 +2 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; +if (smm665_is_critical (val)) + data->cu[i] =smm665_convert (val, i); +else + data->au[i] =smm665_convert (val, i); + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 +4 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; + data->co[i] = data->ao[i] =smm665_convert (val, i); + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 +6 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; +if (smm665_is_critical (val)) + data->co[i] =smm665_convert (val, i); +else + data->ao[i] =smm665_convert (val, i); + } + +/* Register sysfs hooks */ + ret =sysfs_create_group (&client->dev.kobj, &smm665_group); +if (ret) + goto out_sysfs_create_group; + + data->hwmon_dev =hwmon_device_register (&client->dev); +if (IS_ERR (data->hwmon_dev)) { + ret =PTR_ERR (data->hwmon_dev); + goto out_hwmon_device_register; + } + +return 0 ; + +out_hwmon_device_register: +sysfs_remove_group (&client->dev.kobj, &smm665_group); +out_sysfs_create_group: +i2c_unregister_device (data->cmdreg); +out_new_dummy: +kfree (data); +out_kzalloc: +return ret; +} + +static int smm665_remove (struct i2c_client *client) +{ +struct smm665_data *data =i2c_get_clientdata (client);drivers/hwmon/smm665.c line 706
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+ +i2c_unregister_device (data->cmdreg); +hwmon_device_unregister (data->hwmon_dev); +sysfs_remove_group (&client->dev.kobj, &smm665_group); + +kfree (data); + +return 0 ; +} +Personally I'd be cynical. If the other devices you list above should work. I'd add them to the id table and
Kconfigdescription and just put a note saying they are untested.Obviously don't do this if you have any reason to suspect they are not fully compatible.
But then that is me :)
Quoted 31 lines
drivers/hwmon/smm665.c new file +31
-0+static const struct i2c_device_id smm665_id[] = { + {"smm665" ,0 }, + {} +}; + +MODULE_DEVICE_TABLE (i2c, smm665_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver smm665_driver = { + .driver = { + .name ="smm665" , + }, + .probe = smm665_probe, + .remove = smm665_remove, + .id_table = smm665_id, +}; + +static int __init smm665_init (void ) +{ +return i2c_add_driver (&smm665_driver); +} + +static void __exit smm665_exit(void) +{ +i2c_del_driver (&smm665_driver); +} + +MODULE_AUTHOR ("Guenter Roeck" ); +MODULE_DESCRIPTION ("SMM665 driver" ); +MODULE_LICENSE ("GPL" ); +
Quoted 9 lines
drivers/hwmon/smm665.c line 739
Quoted 2 lines
drivers/hwmon/smm665.c new file +2
-0+module_init (smm665_init); +module_exit (smm665_exit);_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [lm-sensors] [PATCH 1/3] hwmon: Driver for SMM665 Six-Channel Active DC Output Controller/Monitor
Quoted 13 lines · Jonathan Cameron
Quoted 12 lines · Jonathan Cameron
Hi,
I've taken a quick look through this code.
One or two specific comments below.
Only big question is why have the limit functionality in this driver? Given the device has no hardware support and you don't have any form of regular polling (I think) then these limits will only be noticed if you query them. Hence why not leave this job to userspace?
Quoted 7 lines
Quoted 2 lines
I'm not saying you are wrong to do this. Just that you need to explain your reasoning alongside the patch.
Another quick query. Are the
_min/_maxattributes as defined in the abi meant for alarms? I always thought they were to tell userspace the limits on measurement?
Good question. I thought it is supposed to refer to alarm limits, but I may be wrong.
Browsing through a couple of drivers, it _looks_ like the values are used for alarm limits (eg adm1025 or lm85). Limits are not always set to useful values, though. This is what my CPU board returns:
lm85-i2c-0-2e
Adapter: SMBus PIIX4 adapter at 0580 V1.5: +1.80 V (min = +0.00 V, max = +3.32 V) VCore: +1.29 V (min = +0.00 V, max = +2.99 V) V3.3: +3.32 V (min = +0.00 V, max = +4.38 V) V5: +5.00 V (min = +0.00 V, max = +6.64 V) V12: +12.12 V (min = +0.00 V, max = +15.94 V)
The lm85 datasheet says: "If a voltage input either exceeds the value set in the voltage high limit register or falls below the value set in the voltage low limit register, the corresponding bit will be set automatically by the LM85 in the interrupt status registers (41-42h)."
Quoted 2 lines
Either way, one of us has misunderstood so perhaps the documentation needs to be more specific....
Agreed.
Guenter
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [lm-sensors] [PATCH 1/3] hwmon: Driver for SMM665 Six-Channel Active DC Output Controller/Monitor
Quoted 10 lines · Guenter Roeck
Quoted 4 lines · Jonathan Cameron
Another quick query. Are the
_min/_maxattributes as defined in the abi meant for alarms? I always thought they were to tell userspace the limits on measurement?Good question. I thought it is supposed to refer to alarm limits, but I may be wrong.
Browsing through a couple of drivers, it _looks_ like the values are used for alarm limits (eg adm1025 or lm85). Limits are not always set to
Yes, these are alarms. _min and _max are really misnomers, these should have been _low and _high but by the time I realized it, _min and _max were already de facto standards and it was too late to change this.
Documentation/hwmon/sysfs-interface says:
Usual items are "input" (measured value), "max" (high threshold, "min" (low threshold).
Specific occurrences are then left without details. If you think this document can be improved, I welcome patches.
Quoted 19 lines
useful values, though. This is what my CPU board returns:
lm85-i2c-0-2e
Adapter: SMBus PIIX4 adapter at 0580 V1.5: +1.80 V (min = +0.00 V, max = +3.32 V) VCore: +1.29 V (min = +0.00 V, max = +2.99 V) V3.3: +3.32 V (min = +0.00 V, max = +4.38 V) V5: +5.00 V (min = +0.00 V, max = +6.64 V) V12: +12.12 V (min = +0.00 V, max = +15.94 V)The lm85 datasheet says: "If a voltage input either exceeds the value set in the voltage high limit register or falls below the value set in the voltage low limit register, the corresponding bit will be set automatically by the LM85 in the interrupt status registers (41-42h)."
Quoted 2 lines
Either way, one of us has misunderstood so perhaps the documentation needs to be more specific....
Agreed.
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [lm-sensors] [PATCH 1/3] hwmon: Driver for SMM665 Six-Channel Active DC Output Controller/Monitor
Quoted 12 lines · Jean Delvare
Quoted 10 lines · Guenter Roeck
Quoted 4 lines · Jonathan Cameron
Another quick query. Are the
_min/_maxattributes as defined in the abi meant for alarms? I always thought they were to tell userspace the limits on measurement?Good question. I thought it is supposed to refer to alarm limits, but I may be wrong.
Browsing through a couple of drivers, it _looks_ like the values are used for alarm limits (eg adm1025 or lm85). Limits are not always set to
Quoted 8 lines
Yes, these are alarms.
_minand_maxare really misnomers, these should have been_lowand_highbut by the time I realized it,_minand_maxwere already de facto standards and it was too late to change this.
Documentation/hwmon/sysfs-interfacesays:Usual items are "input" (measured value), "max" (high threshold, "min" (low threshold).
Ah, I missed that general defining of terms. It's fine as is unless we end up with lots of people not reading it properly like me ;)
Quoted 24 lines
Specific occurrences are then left without details. If you think this document can be improved, I welcome patches.
Quoted 19 lines
useful values, though. This is what my CPU board returns:
lm85-i2c-0-2e
Adapter: SMBus PIIX4 adapter at 0580 V1.5: +1.80 V (min = +0.00 V, max = +3.32 V) VCore: +1.29 V (min = +0.00 V, max = +2.99 V) V3.3: +3.32 V (min = +0.00 V, max = +4.38 V) V5: +5.00 V (min = +0.00 V, max = +6.64 V) V12: +12.12 V (min = +0.00 V, max = +15.94 V)The lm85 datasheet says: "If a voltage input either exceeds the value set in the voltage high limit register or falls below the value set in the voltage low limit register, the corresponding bit will be set automatically by the LM85 in the interrupt status registers (41-42h)."
Quoted 2 lines
Either way, one of us has misunderstood so perhaps the documentation needs to be more specific....
Agreed.
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [PATCH 1/3] hwmon: Driver for SMM665 Six-Channel Active DC Output Controller/Monitor
In reply to Jonathan Cameron[...]
Quoted 13 lines
drivers/hwmon/smm665.c line 186
Quoted 13 lines
drivers/hwmon/smm665.c new file +13
-0+/* +* Algorithm for reading ADC, per SMM665 datasheet +* +* {[S][addr][W][Ack]} {[offset][Ack]} {[S][addr][R][Nack]} +* [wait 70 uS] +* {[S][addr][R][Ack]} {[datahi][Ack]} {[datalo][Ack][P]} +* +* To implement the first part of this exchange, +* do a full read transaction and expect a failure/Nack. +* This sets up the address pointer on the SMM665 +* and starts the ADC conversion. +* Then do a two-byte read transaction. +*/
Quoted 9 lines
Is there no better way of handling this? There are protocol mangling hacks to tell the i2c core to ignore a NAKs under some circumstances.
Quoted 6 lines
drivers/hwmon/smm665.c new file +6
-0+ rv =i2c_smbus_read_byte_data (client, adc <<3 ); +if (rv >=0 ) { +/* No error, something is wrong. Retry. */ + rv =-1 ; +continue ; + }
I looked through the core i2c code, but did not find anything I can use.
Problem is that per smm665 specification, the first NACK is expected. So we do not just want to ignore this NACK, we want to actively check if the command "failed" as expected, and report an error if it did _not_ fail.
Guenter
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [lm-sensors] [PATCH 1/3] hwmon: Driver for SMM665 Six-Channel Active DC Output Controller/Monitor
Quoted 27 lines · Guenter Roeck
[...]
Quoted 13 lines
drivers/hwmon/smm665.c line 186
Quoted 13 lines
drivers/hwmon/smm665.c new file +13
-0+/* +* Algorithm for reading ADC, per SMM665 datasheet +* +* {[S][addr][W][Ack]} {[offset][Ack]} {[S][addr][R][Nack]} +* [wait 70 uS] +* {[S][addr][R][Ack]} {[datahi][Ack]} {[datalo][Ack][P]} +* +* To implement the first part of this exchange, +* do a full read transaction and expect a failure/Nack. +* This sets up the address pointer on the SMM665 +* and starts the ADC conversion. +* Then do a two-byte read transaction. +*/ Quoted 9 lines
Is there no better way of handling this? There are protocol mangling hacks to tell the i2c core to ignore a NAKs under some circumstances.
Quoted 6 lines
drivers/hwmon/smm665.c new file +6
-0+ rv =i2c_smbus_read_byte_data (client, adc <<3 ); +if (rv >=0 ) { +/* No error, something is wrong. Retry. */ + rv =-1 ; +continue ; + }I looked through the core i2c code, but did not find anything I can use.
Quoted 6 lines
Problem is that per smm665 specification, the first NACK is expected. So we do not just want to ignore this NACK, we want to actively check if the command "failed" as expected, and report an error if it did _not_ fail.
Guenter
To my mind this looks like a case for adding another 'mangling' flag to the core, but I guess that might require bus driver implementation which would obviously be a pain. Perhaps the approach you have taken is the best plan. My issue with it at the moment is that you are detecting any error rather than specifically an unexpected NACK.
Jonathan
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [lm-sensors] [PATCH 1/3] hwmon: Driver for SMM665 Six-Channel Active DC Output Controller/Monitor
Quoted 33 lines · Jonathan Cameron
Quoted 32 lines · Guenter Roeck
[...]
Quoted 13 lines
drivers/hwmon/smm665.c line 186
Quoted 13 lines
drivers/hwmon/smm665.c new file +13
-0+/* +* Algorithm for reading ADC, per SMM665 datasheet +* +* {[S][addr][W][Ack]} {[offset][Ack]} {[S][addr][R][Nack]} +* [wait 70 uS] +* {[S][addr][R][Ack]} {[datahi][Ack]} {[datalo][Ack][P]} +* +* To implement the first part of this exchange, +* do a full read transaction and expect a failure/Nack. +* This sets up the address pointer on the SMM665 +* and starts the ADC conversion. +* Then do a two-byte read transaction. +*/ Quoted 9 lines
Is there no better way of handling this? There are protocol mangling hacks to tell the i2c core to ignore a NAKs under some circumstances.
Quoted 6 lines
drivers/hwmon/smm665.c new file +6
-0+ rv =i2c_smbus_read_byte_data (client, adc <<3 ); +if (rv >=0 ) { +/* No error, something is wrong. Retry. */ + rv =-1 ; +continue ; + }I looked through the core i2c code, but did not find anything I can use.
Problem is that per smm665 specification, the first NACK is expected. So we do not just want to ignore this NACK, we want to actively check if the command "failed" as expected, and report an error if it did _not_ fail.
Quoted 6 lines
Quoted 1 line
Guenter
To my mind this looks like a case for adding another 'mangling' flag to the core, but I guess that might require bus driver implementation which would obviously be a pain. Perhaps the approach you have taken is the best plan. My issue with it at the moment is that you are detecting any error rather than specifically an unexpected NACK.
Yes, but looking through bus implementations, I don't think there is a consistent way to detect the exact error reason. How about if I weed out -EOPNOTSUPP, -ETIMEDOUT, and -EINVAL ?
Guenter
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [PATCH 1/3] hwmon: Driver for SMM665 Six-Channel Active DC Output Controller/Monitor
In reply to Guenter RoeckQuoted 14 lines · Guenter Roeck
[...]
Quoted 13 lines
Quoted 13 lines
drivers/hwmon/smm665.c new file +13
-0+/* +* Algorithm for reading ADC, per SMM665 datasheet +* +* {[S][addr][W][Ack]} {[offset][Ack]} {[S][addr][R][Nack]} +* [wait 70 uS] +* {[S][addr][R][Ack]} {[datahi][Ack]} {[datalo][Ack][P]} +* +* To implement the first part of this exchange, +* do a full read transaction and expect a failure/Nack. +* This sets up the address pointer on the SMM665 +* and starts the ADC conversion. +* Then do a two-byte read transaction. +*/
Quoted 2 lines
Quoted 2 lines
Is there no better way of handling this? There are protocol mangling hacks to tell the i2c core to ignore a NAKs under some circumstances.
This is only available on raw I2C messages, not on the higher-level i2c_smbus_*() API. And not all bus drivers support it. And that's not what is needed here anyway: ignoring the nack means we would continue reading from the chip, while it really doesn't want to talk to us at that time.
Quoted 2 lines
Quoted 2 lines
drivers/hwmon/smm665.c line 188
Quoted 2 lines
drivers/hwmon/smm665.c new file +2
-0+ rv =i2c_smbus_read_byte_data (client, adc <<3 ); +if (rv >=0 ) {
You should check for -ENXIO explicitly. According to Documentation/i2c/fault-codes, this is the value bus drivers should return on missing Ack.
Quoted 5 lines
Quoted 4 lines
drivers/hwmon/smm665.c line 192
Quoted 4 lines
drivers/hwmon/smm665.c new file +4
-0+/* No error, something is wrong. Retry. */ + rv =-1 ; +continue ; + }
Quoted 7 lines
I looked through the core i2c code, but did not find anything I can use.
Problem is that per smm665 specification, the first NACK is expected. So we do not just want to ignore this NACK, we want to actively check if the command "failed" as expected, and report an error if it did _not_ fail.
Do you really have to trigger the Nack for the ADC conversion to start? Can't you just use i2c_smbus_read_byte() (no _data) for the first part of the transaction?
Signature · 6 lines
Jean Delvare _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [lm-sensors] [PATCH 1/3] hwmon: Driver for SMM665 Six-Channel
In reply to Guenter RoeckQuoted 4 lines · Jonathan Cameron
Hi,
I've taken a quick look through this code.
Thanks ...
Quoted 10 lines
One or two specific comments below.
Only big question is why have the limit functionality in this driver? Given the device has no hardware support and you don't have any form of regular polling (I think) then these limits will only be noticed if you query them. Hence why not leave this job to userspace?
I'm not saying you are wrong to do this. Just that you need to explain your reasoning alongside the patch.
Guess that depends on what min/max values are used for. My understanding is that the values are supposed to be alarm limits, but I may be wrong.
In respect to alarms, that may be a misunderstanding on my side. You are right, comparing current values with min/max values can be done by userspace code. I have no problem removing the related files/functions if that is the preferred implementation.
More comments inline.
Thanks,
Guenter
Quoted 77 lines · Guenter Roeck
Quoted 75 lines
This driver adds support for the monitoring features of the Summit Microelectronics SMM665 Six-Channel Active DC Output Controller/Monitor.
Signed-off-by Guenter Roeck <[email protected]>--- drivers/hwmon/Kconfig | 12 + drivers/hwmon/Makefile | 1 + drivers/hwmon/smm665.c | 739 ++++++++++++++++++++++++++++++++++++++++++++++++ 3 files changed, 752 insertions(+), 0 deletions(-) create mode 100644 drivers/hwmon/smm665.cdrivers/hwmon/Kconfig +12
-0@@ -739,6 +739,18 @@ config SENSORS_SIS5595 This driver can also be built as a module. If so, the module will be called sis5595. +config SENSORS_SMM665 + tristate "Summit Microelectronics SMM665" + depends on I2C && EXPERIMENTAL + default n + help + If you say yes here you get support for the hardware monitoring + features of the Summit Microelectronics SMM665 Six-Channel + Active DC Output Controller / Monitor. + + This driver can also be built as a module. If so, the module will + be called smm665. + config SENSORS_DME1737 tristate "SMSC DME1737, SCH311x and compatibles" depends on I2C && EXPERIMENTALdrivers/hwmon/Makefile +1
-0@@ -76,6 +76,7 @@ obj-$(CONFIG_SENSORS_LM93) += lm93.o obj-$(CONFIG_SENSORS_LM95241) += lm95241.o obj-$(CONFIG_SENSORS_LTC4215) += ltc4215.o obj-$(CONFIG_SENSORS_LTC4245) += ltc4245.o +obj-$(CONFIG_SENSORS_SMM665) += smm665.o obj-$(CONFIG_SENSORS_MAX1111) += max1111.o obj-$(CONFIG_SENSORS_MAX1619) += max1619.o obj-$(CONFIG_SENSORS_MAX6650) += max6650.odrivers/hwmon/smm665.c new file +23
-0@@ -0,0 +1,739 @@ +/* +* Driver for SMM665 Power Controller / Monitor +* +* Copyright (C) 2010 Ericsson AB. +* +* This program is free software; you can redistribute it and/or modify +* it under the terms of the GNU General Public License as published by +* the Free Software Foundation; version 2 of the License. +* +* This driver should with no or minor modifications also work for SMM766, +* SMM764, and SMM465. Only monitoring functionality is implemented. +* +* Datasheets: +* http://www.summitmicro.com/prod_select/summary/SMM665/SMM665B_2089_20.pdf +* http://www.summitmicro.com/prod_select/summary/SMM766B/SMM766B_2122.pdf +*/ + +#include <linux/kernel.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/err.h> +#include <linux/slab.h> +#include <linux/i2c.h>
Quoted 9 lines
drivers/hwmon/smm665.c line 27
Quoted 4 lines
drivers/hwmon/smm665.c new file +4
-0+#include <linux/hwmon.h> +#include <linux/hwmon-sysfs.h> +#include <linux/delay.h> +Personally I'd be more inclined to do these as a whole lot of '#define's. You never use the enum type for anything so why bother?
enum was used in the ltc4245 driver which I used as a start, which is the only reason for using it here. No problem replacing it with defines if that is preferred. I'll follow your and other people's guidance here.
Quoted 76 lines
Quoted 76 lines
drivers/hwmon/smm665.c new file +76
-0+/* ADC channel addresses */ +enum smm665_adcregs { +SMM665_MISC16_ADC_DATA_A =0x00 , +SMM665_MISC16_ADC_DATA_B =0x01 , +SMM665_MISC16_ADC_DATA_C =0x02 , +SMM665_MISC16_ADC_DATA_D =0x03 , +SMM665_MISC16_ADC_DATA_E =0x04 , +SMM665_MISC16_ADC_DATA_F =0x05 , +SMM665_MISC16_ADC_DATA_VDD =0x06 , +SMM665_MISC16_ADC_DATA_12V =0x07 , +SMM665_MISC16_ADC_DATA_INT_TEMP =0x08 , +SMM665_MISC16_ADC_DATA_AIN1 =0x09 , +SMM665_MISC16_ADC_DATA_AIN2 =0x0a , +}; + +enum smm665_cmdregs { +SMM665_MISC8_CMD_STS =0x80 , +SMM665_MISC8_STATUS1 =0x81 , +SMM665_MISC8_STATUSS2 =0x82 , +SMM665_MISC8_IO_POLARITY =0x83 , +SMM665_MISC8_PUP_POLARITY =0x84 , +SMM665_MISC8_ADOC_STATUS1 =0x85 , +SMM665_MISC8_ADOC_STATUS2 =0x86 , +SMM665_MISC8_WRITE_PROT =0x87 , +SMM665_MISC8_STS_TRACK =0x88 , +}; + +/* +* Configuration registers and register groups +*/ +#define SMM665_ADOC_ENABLE 0x0d +#define SMM665_LIMIT_BASE 0x80 + +/* +* Limit register bit masks +*/ +#define SMM665_TRIGGER_RST 0x8000 +#define SMM665_TRIGGER_HEALTHY 0x4000 +#define SMM665_TRIGGER_POWEROFF 0x2000 +#define SMM665_TRIGGER_SHUTDOWN 0x1000 +#define SMM665_ADC_MASK 0x03ff + +#define smm665_is_critical (lim) ((lim) & (SMM665_TRIGGER_RST \ + | SMM665_TRIGGER_POWEROFF \ + | SMM665_TRIGGER_SHUTDOWN)) +/* +* Fault register bit definitions +* Values are merged from status registers 1/2, +* with status register 1 providing the upper 8 bits. +*/ +#define SMM665_FAULT_A 0x0001 +#define SMM665_FAULT_B 0x0002 +#define SMM665_FAULT_C 0x0004 +#define SMM665_FAULT_D 0x0008 +#define SMM665_FAULT_E 0x0010 +#define SMM665_FAULT_F 0x0020 +#define SMM665_FAULT_VDD 0x0040 +#define SMM665_FAULT_12V 0x0080 +#define SMM665_FAULT_TEMP 0x0100 +#define SMM665_FAULT_AIN1 0x0200 +#define SMM665_FAULT_AIN2 0x0400 + +/* +* I2C Register addresses +* +* The configuration register needs to be the configured base register. +* The command/status register address is derived from it. +*/ +#define SMM665_REGMASK 0x78 +#define SMM665_CMDREG_BASE 0x48 +#define SMM665_CONFREG_BASE 0x50 + +/* Internal reference voltage (VREF, x 1000 */ +#define SMM665_VREF_ADC_X1000 1250 + +/*
Quoted 8 lines
drivers/hwmon/smm665.c line 108
Quoted 5 lines
drivers/hwmon/smm665.c new file +5
-0+* Equations given by chip manufacturer to calculate voltage/temperature values +* vref = Reference voltage on VREF_ADC pin +* adc = 10bit ADC value read back from registers +*/ +I guess these are handy if you ever intend to allow different reference voltages, but right now they add code and reduce readability. Obviously leave be if the intent is add that vref control in a later patch!
I would prefer to leave it in, and keep the possibility to add vref support, say, with a module parameter if needed (or I can do that right away if people think it makes sense to have it available).
Quoted 21 lines
Quoted 21 lines
drivers/hwmon/smm665.c new file +21
-0+/* Voltage A-F and VDD */ +#define SMM665_VMON_ADC_TO_VOLTS (vref, adc) ((adc) * (vref) / 256) + +/* Voltage 12VIN */ +#define SMM665_12VIN_ADC_TO_VOLTS (vref, adc) ((adc) * (vref) * 3 / 256) + +/* Voltage AIN1, AIN2 */ +#define SMM665_AIN_ADC_TO_VOLTS (vref, adc) ((adc) * (vref) / 512) + +/* Temp Sensor */ +#define SMM665_TEMP_ADC_TO_CELSIUS (adc) ((adc) <= 511) ? \ + ((int)(adc) * 1000 / 4) : \ + (((int)(adc) - 0x400) * 1000 / 4) + +#define SMM665_NUM_ADC 11 +#define SMM665_ADC_RETRIES 5 +#define SMM665_ADC_WAIT 100/* conversion time is 70 uS for SMM665B, +182 uS for SMM766 */ + +struct smm665_data { +struct device *hwmon_dev;
Quoted 8 lines
drivers/hwmon/smm665.c line 135
Quoted 6 lines
drivers/hwmon/smm665.c new file +6
-0+ +struct mutex update_lock; +bool valid; +unsigned long last_updated;/* in jiffies */ +u16 adc[SMM665_NUM_ADC ];/* adc values (raw) */ +u16 faults;/* fault status */ Given these aren't used often, I'd prefer more meaningful variable names.
Ok.
Quoted 29 lines
Quoted 29 lines
drivers/hwmon/smm665.c new file +29
-0+int cu[SMM665_NUM_ADC ];/* critical under limit (converted) */ +int au[SMM665_NUM_ADC ];/* alarm under limit (converted) */ +int co[SMM665_NUM_ADC ];/* critical over limit (converted) */ +int ao[SMM665_NUM_ADC ];/* alarm over limit (converted) */ +struct i2c_client *cmdreg; +}; + +/* +* smm665_read16() +* +* Read 16 bit value from <reg>, <reg+1>. Upper 8 bits are in <reg>. +*/ +static int smm665_read16 (struct i2c_client *client,int reg) +{ +int rv, val; + + rv =i2c_smbus_read_byte_data (client, reg); +if (rv <0 ) +return rv; + val = rv <<8 ; + rv =i2c_smbus_read_byte_data (client, reg +1 ); +if (rv <0 ) +return rv; + val |= rv; +return val; +} + +/* +* Read adc value.
Quoted 8 lines
drivers/hwmon/smm665.c line 170
Quoted 6 lines
drivers/hwmon/smm665.c new file +6
-0+*/ +static int smm665_read_adc (struct i2c_client *client,int adc) +{ +int rv =-1 ; +int retries; +Why the retries? If there is a reason for this to sometimes fail, please add a comment explaining what it is! If it is a hardware bug, then tell us!
No real reason. Leftover from original (non-linux) driver, which tried to be over-cautious and redundant. I'll remove it.
Quoted 16 lines
Quoted 6 lines
drivers/hwmon/smm665.c new file +6
-0+for (retries =0 ; retries <SMM665_ADC_RETRIES ; retries++) { +int radc; + +/* +* Algorithm for reading ADC, per SMM665 datasheet +* drivers/hwmon/smm665.c line 186
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+* {[S][addr][W][Ack]} {[offset][Ack]} {[S][addr][R][Nack]} +* [wait 70 uS] +* {[S][addr][R][Ack]} {[datahi][Ack]} {[datalo][Ack][P]} +* +* To implement the first part of this exchange, +* do a full read transaction and expect a failure/Nack. +* This sets up the address pointer on the SMM665 +* and starts the ADC conversion. +* Then do a two-byte read transaction. +*/
Quoted 3 lines
Is there no better way of handling this? There are protocol mangling hacks to tell the i2c core to ignore a NAKs under some circumstances.
I tried several other methods, but have not been able to find anything that worked. Do you have a reference to the hacks you mention ?
Quoted 30 lines
Quoted 20 lines
drivers/hwmon/smm665.c new file +20
-0+ rv =i2c_smbus_read_byte_data (client, adc <<3 ); +if (rv >=0 ) { +/* No error, something is wrong. Retry. */ + rv =-1 ; +continue ; + } +udelay (SMM665_ADC_WAIT ); +/* +* Now read two bytes. +* +* Neither i2c_smbus_read_byte() nor +* i2c_smbus_read_block_data() worked here, +* so use i2c_smbus_read_word_data() instead. +* We could also try to use i2c_master_recv(), +* but that is not always supported. +*/ + rv =i2c_smbus_read_word_data (client,0 ); +if (rv <0 ) +continue ; +/* drivers/hwmon/smm665.c line 216
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+* Validate/verify readback adc channel (in bit 11..14) +* High byte is in lower 8 bit of rv, so only shift by 3. +*/ + radc = (rv >>3 ) &0x0f ; +if (radc != adc) { + rv =-1 ; +continue ; + } + +/* Byte order is reversed, need to swap. */
Quoted 1 line
Isn't this endian dependent?
SMM665 sends the high byte first, followed by the low byte. SMBus specifies that the low byte has to be sent first in a read_word comand, followed by the high byte. So the byte order is always reversed, independent of CPU endianness.
Quoted 112 lines
Quoted 112 lines
drivers/hwmon/smm665.c new file +112
-0+ rv =swab16 (rv) &SMM665_ADC_MASK ; +break ; + } +return rv; +} + +static struct smm665_data *smm665_update_device (struct device *dev) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client); + +mutex_lock (&data->update_lock); + +if (time_after (jiffies, data->last_updated +HZ ) || !data->valid) { +int i, faults; + +/* +* read status registers +*/ + faults =smm665_read16 (client,SMM665_MISC8_STATUS1 ); +if (unlikely (faults <0 )) + data->faults =0 ; +else + data->faults = faults; + +/* Read adc registers */ +for (i =0 ; i <SMM665_NUM_ADC ; i++) { +int val =smm665_read_adc (data->cmdreg, i); +if (unlikely (val <0 )) + data->adc[i] =0 ; +else + data->adc[i] = val; + } + + data->last_updated = jiffies; + data->valid =1 ; + } + +mutex_unlock (&data->update_lock); + +return data; +} + +/* Return converted value from given adc */ +static int smm665_convert (u16 adcval,int index) +{ +int val =0 ; + +switch (index) { +case SMM665_MISC16_ADC_DATA_12V : + val =SMM665_12VIN_ADC_TO_VOLTS (SMM665_VREF_ADC_X1000 , + adcval &SMM665_ADC_MASK ); +break ; + +case SMM665_MISC16_ADC_DATA_VDD : +case SMM665_MISC16_ADC_DATA_A : +case SMM665_MISC16_ADC_DATA_B : +case SMM665_MISC16_ADC_DATA_C : +case SMM665_MISC16_ADC_DATA_D : +case SMM665_MISC16_ADC_DATA_E : +case SMM665_MISC16_ADC_DATA_F : + val =SMM665_VMON_ADC_TO_VOLTS (SMM665_VREF_ADC_X1000 , + adcval &SMM665_ADC_MASK ); +break ; + +case SMM665_MISC16_ADC_DATA_AIN1 : +case SMM665_MISC16_ADC_DATA_AIN2 : + val =SMM665_AIN_ADC_TO_VOLTS (SMM665_VREF_ADC_X1000 , + adcval &SMM665_ADC_MASK ); +break ; + +case SMM665_MISC16_ADC_DATA_INT_TEMP : + val =SMM665_TEMP_ADC_TO_CELSIUS (adcval &SMM665_ADC_MASK ); +break ; + +default : +/* If we get here, the developer messed up */ +WARN_ON_ONCE (1 ); +break ; + } + +return val; +} + +/* Return converted value from given adc */ +static int smm665_get_input (struct device *dev,int adc) +{ +struct smm665_data *data =smm665_update_device (dev); + +return smm665_convert (data->adc[adc], adc); +} + +static int smm665_get_min (struct device *dev,int index) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client); + +return data->au[index]; +} + +static int smm665_get_max (struct device *dev,int index) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client); + +return data->ao[index]; +} + +static int smm665_get_crit (struct device *dev,int index) +{ +struct i2c_client *client =to_i2c_client (dev); +struct smm665_data *data =i2c_get_clientdata (client);
Quoted 9 lines
drivers/hwmon/smm665.c line 332
Quoted 4 lines
drivers/hwmon/smm665.c new file +4
-0+ +return data->co[index]; +} +I'm confused. So these alarms are purely software constructs. Given I don't think the device does regular polling, why not leave this to userspace?
No problem here. Maybe a misunderstanding on my side about the meaning of _alarm files.
For clarification, I think you are saying that _alarm files should only be supported if the chip provides a specific alarm status. Is that correct ? If so, I'll take the functions out.
Quoted 4 lines
Quoted 4 lines
drivers/hwmon/smm665.c new file +4
-0+static int smm665_get_min_alarm (struct device *dev,int index) +{ +struct smm665_data *data =smm665_update_device (dev); +int val =smm665_convert (data->adc[index], index);
Quoted 8 lines
drivers/hwmon/smm665.c line 343
Quoted 7 lines
drivers/hwmon/smm665.c new file +7
-0+ +/* +* Look for lower alarm limit. Report alarm if the current +* adc value is equal to or lower than the specified limit. +*/ +if (val <= data->au[index]) +return 1 ;(nitpick) Inconsistent spacing between this and the next function.
Thanks.
Quoted 262 lines
Quoted 262 lines
drivers/hwmon/smm665.c new file +262
-0+return 0 ; +} + +static int smm665_get_max_alarm (struct device *dev,int index) +{ +struct smm665_data *data =smm665_update_device (dev); +int val =smm665_convert (data->adc[index], index); + +/* +* Look for upper alarm limit. Report alarm if the current +* adc value is equal to or larger than the specified limit. +*/ +if (val >= data->ao[index]) +return 1 ; + +return 0 ; +} + +static int smm665_get_fault (struct device *dev,int index) +{ +struct smm665_data *data =smm665_update_device (dev); + +if (data->faults & (1 << index)) +return 1 ; + +return 0 ; +} + +#define SMM665_SHOW (what) \ + static ssize_t smm665_show_##what(struct device *dev, \ + struct device_attribute *da, char *buf) \ +{ \ + struct sensor_device_attribute *attr = to_sensor_dev_attr(da); \ + const int val = smm665_get_##what(dev, attr->index); \ + return snprintf(buf, PAGE_SIZE, "%d\n", val); \ +} + +SMM665_SHOW (input); +SMM665_SHOW (min); +SMM665_SHOW (max); +SMM665_SHOW (crit); +SMM665_SHOW (fault); +SMM665_SHOW (min_alarm); +SMM665_SHOW (max_alarm); + +/* These macros are used below in constructing device attribute objects +* for use with sysfs_create_group() to make a sysfs device file +* for each register. +*/ + +#define SMM665_ATTR (name, type, cmd_idx) \ + static SENSOR_DEVICE_ATTR(name##_##type, S_IRUGO, \ + smm665_show_##type, NULL, cmd_idx) + +/* Construct a sensor_device_attribute structure for each register */ + +/* Input voltages */ +SMM665_ATTR (in1, input,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, input,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, input,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, input,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, input,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, input,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, input,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, input,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, input,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, input,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltages min */ +SMM665_ATTR (in1, min,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, min,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, min,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, min,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, min,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, min,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, min,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, min,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, min,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, min,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltages max */ +SMM665_ATTR (in1, max,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, max,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, max,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, max,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, max,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, max,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, max,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, max,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, max,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, max,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltage min alarms */ +SMM665_ATTR (in1, min_alarm,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, min_alarm,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, min_alarm,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, min_alarm,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, min_alarm,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, min_alarm,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, min_alarm,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, min_alarm,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, min_alarm,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, min_alarm,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Input voltage max alarms */ +SMM665_ATTR (in1, max_alarm,SMM665_MISC16_ADC_DATA_12V ); +SMM665_ATTR (in2, max_alarm,SMM665_MISC16_ADC_DATA_VDD ); +SMM665_ATTR (in3, max_alarm,SMM665_MISC16_ADC_DATA_A ); +SMM665_ATTR (in4, max_alarm,SMM665_MISC16_ADC_DATA_B ); +SMM665_ATTR (in5, max_alarm,SMM665_MISC16_ADC_DATA_C ); +SMM665_ATTR (in6, max_alarm,SMM665_MISC16_ADC_DATA_D ); +SMM665_ATTR (in7, max_alarm,SMM665_MISC16_ADC_DATA_E ); +SMM665_ATTR (in8, max_alarm,SMM665_MISC16_ADC_DATA_F ); +SMM665_ATTR (in9, max_alarm,SMM665_MISC16_ADC_DATA_AIN1 ); +SMM665_ATTR (in10, max_alarm,SMM665_MISC16_ADC_DATA_AIN2 ); + +/* Faults */ +SMM665_ATTR (in1, fault,SMM665_FAULT_12V ); +SMM665_ATTR (in2, fault,SMM665_FAULT_VDD ); +SMM665_ATTR (in3, fault,SMM665_FAULT_A ); +SMM665_ATTR (in4, fault,SMM665_FAULT_B ); +SMM665_ATTR (in5, fault,SMM665_FAULT_C ); +SMM665_ATTR (in6, fault,SMM665_FAULT_D ); +SMM665_ATTR (in7, fault,SMM665_FAULT_E ); +SMM665_ATTR (in8, fault,SMM665_FAULT_F ); +SMM665_ATTR (in9, fault,SMM665_FAULT_AIN1 ); +SMM665_ATTR (in10, fault,SMM665_FAULT_AIN2 ); + +/* Temperature */ +SMM665_ATTR (temp1, input,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, min,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, max,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, crit,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, min_alarm,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, max_alarm,SMM665_MISC16_ADC_DATA_INT_TEMP ); +SMM665_ATTR (temp1, fault,SMM665_FAULT_TEMP ); + +/* +* Finally, construct an array of pointers to members of the above objects, +* as required for sysfs_create_group() +*/ +static struct attribute *smm665_attributes[] = { + &sensor_dev_attr_in1_input.dev_attr.attr, + &sensor_dev_attr_in1_min.dev_attr.attr, + &sensor_dev_attr_in1_max.dev_attr.attr, + &sensor_dev_attr_in1_min_alarm.dev_attr.attr, + &sensor_dev_attr_in1_max_alarm.dev_attr.attr, + &sensor_dev_attr_in1_fault.dev_attr.attr, + + &sensor_dev_attr_in2_input.dev_attr.attr, + &sensor_dev_attr_in2_min.dev_attr.attr, + &sensor_dev_attr_in2_max.dev_attr.attr, + &sensor_dev_attr_in2_min_alarm.dev_attr.attr, + &sensor_dev_attr_in2_max_alarm.dev_attr.attr, + &sensor_dev_attr_in2_fault.dev_attr.attr, + + &sensor_dev_attr_in3_input.dev_attr.attr, + &sensor_dev_attr_in3_min.dev_attr.attr, + &sensor_dev_attr_in3_max.dev_attr.attr, + &sensor_dev_attr_in3_min_alarm.dev_attr.attr, + &sensor_dev_attr_in3_max_alarm.dev_attr.attr, + &sensor_dev_attr_in3_fault.dev_attr.attr, + + &sensor_dev_attr_in4_input.dev_attr.attr, + &sensor_dev_attr_in4_min.dev_attr.attr, + &sensor_dev_attr_in4_max.dev_attr.attr, + &sensor_dev_attr_in4_min_alarm.dev_attr.attr, + &sensor_dev_attr_in4_max_alarm.dev_attr.attr, + &sensor_dev_attr_in4_fault.dev_attr.attr, + + &sensor_dev_attr_in5_input.dev_attr.attr, + &sensor_dev_attr_in5_min.dev_attr.attr, + &sensor_dev_attr_in5_max.dev_attr.attr, + &sensor_dev_attr_in5_min_alarm.dev_attr.attr, + &sensor_dev_attr_in5_max_alarm.dev_attr.attr, + &sensor_dev_attr_in5_fault.dev_attr.attr, + + &sensor_dev_attr_in6_input.dev_attr.attr, + &sensor_dev_attr_in6_min.dev_attr.attr, + &sensor_dev_attr_in6_max.dev_attr.attr, + &sensor_dev_attr_in6_min_alarm.dev_attr.attr, + &sensor_dev_attr_in6_max_alarm.dev_attr.attr, + &sensor_dev_attr_in6_fault.dev_attr.attr, + + &sensor_dev_attr_in7_input.dev_attr.attr, + &sensor_dev_attr_in7_min.dev_attr.attr, + &sensor_dev_attr_in7_max.dev_attr.attr, + &sensor_dev_attr_in7_min_alarm.dev_attr.attr, + &sensor_dev_attr_in7_max_alarm.dev_attr.attr, + &sensor_dev_attr_in7_fault.dev_attr.attr, + + &sensor_dev_attr_in8_input.dev_attr.attr, + &sensor_dev_attr_in8_min.dev_attr.attr, + &sensor_dev_attr_in8_max.dev_attr.attr, + &sensor_dev_attr_in8_min_alarm.dev_attr.attr, + &sensor_dev_attr_in8_max_alarm.dev_attr.attr, + &sensor_dev_attr_in8_fault.dev_attr.attr, + + &sensor_dev_attr_in9_input.dev_attr.attr, + &sensor_dev_attr_in9_min.dev_attr.attr, + &sensor_dev_attr_in9_max.dev_attr.attr, + &sensor_dev_attr_in9_min_alarm.dev_attr.attr, + &sensor_dev_attr_in9_max_alarm.dev_attr.attr, + &sensor_dev_attr_in9_fault.dev_attr.attr, + + &sensor_dev_attr_in10_input.dev_attr.attr, + &sensor_dev_attr_in10_min.dev_attr.attr, + &sensor_dev_attr_in10_max.dev_attr.attr, + &sensor_dev_attr_in10_min_alarm.dev_attr.attr, + &sensor_dev_attr_in10_max_alarm.dev_attr.attr, + &sensor_dev_attr_in10_fault.dev_attr.attr, + + &sensor_dev_attr_temp1_input.dev_attr.attr, + &sensor_dev_attr_temp1_min.dev_attr.attr, + &sensor_dev_attr_temp1_max.dev_attr.attr, + &sensor_dev_attr_temp1_crit.dev_attr.attr, + &sensor_dev_attr_temp1_min_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_max_alarm.dev_attr.attr, + &sensor_dev_attr_temp1_fault.dev_attr.attr, + +NULL , +}; + +static const struct attribute_group smm665_group = { + .attrs = smm665_attributes, +}; + +static int smm665_probe (struct i2c_client *client, +const struct i2c_device_id *id) +{ +struct i2c_adapter *adapter = client->adapter; +struct smm665_data *data; +int i, ret; + +if (!i2c_check_functionality (adapter,I2C_FUNC_SMBUS_BYTE_DATA + |I2C_FUNC_SMBUS_WORD_DATA )) +return -ENODEV ; + +if (i2c_smbus_read_byte_data (client,SMM665_ADOC_ENABLE ) <0 ) +return -ENODEV ; + + data =kzalloc (sizeof (*data),GFP_KERNEL ); +if (!data) { + ret = -ENOMEM ; + goto out_kzalloc; + } + +i2c_set_clientdata (client, data); +mutex_init (&data->update_lock); + + data->cmdreg =i2c_new_dummy (adapter, (client->addr & ~SMM665_REGMASK ) + |SMM665_CMDREG_BASE ); +if (!data->cmdreg) { + ret = -ENOMEM ; + goto out_new_dummy; + } +if (i2c_smbus_read_byte_data (data->cmdreg,SMM665_MISC8_CMD_STS ) <0 ) { + ret = -ENODEV ; + goto out_sysfs_create_group; + } + +/*
Quoted 8 lines
drivers/hwmon/smm665.c line 612
Quoted 7 lines
drivers/hwmon/smm665.c new file +7
-0+* Read limits. +* +* Limit registers start with register SMM665_LIMIT_BASE. +* Each channel uses 8 registers, providing four limit values +* per channel. +* +* Available limits from chip registers, per channel: A simple statement of endianess and number of bytes would do the job.
Ok. I'll try to come up with a simpler description.
Quoted 99 lines
Quoted 84 lines
drivers/hwmon/smm665.c new file +84
-0+* u1: under limit 1 +* u2: under limit 2 +* o1: over limit 1 +* o2: over limit 2 +* +* Register address offsets: +* +0: u1[h] +* +1: u1[l] +* +2: u2[h] +* +3: u2[l] +* +4: o1[h] +* +5: o1[l] +* +6: o2[h] +* +7: o2[l] +* +* Limit register order is as defined with smm665_adcregs, +* so we use smm665_adcregs values throughout the code to index +* limit registers. +* +* We save the first retrieved value both as "critical" and "alarm" +* value. The second value overwrites either the critical or the +* alarm value, depending on its configuration. This ensures that both +* critical and alarm values are initialized, even if both registers are +* configured as critical or non-critical. +* +* Note: Critical values for voltage channels are saved, even though +* this information is currently not used by the driver. This is mostly +* for consistency, though it might eventually be useful if future APIs +* support reporting "critical" voltage values. +*/ + ret = -ENODEV ; +for (i =0 ; i <SMM665_NUM_ADC ; i++) { +int val; + + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; + data->cu[i] = data->au[i] =smm665_convert (val, i); + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 +2 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; +if (smm665_is_critical (val)) + data->cu[i] =smm665_convert (val, i); +else + data->au[i] =smm665_convert (val, i); + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 +4 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; + data->co[i] = data->ao[i] =smm665_convert (val, i); + val =smm665_read16 (client,SMM665_LIMIT_BASE + i *8 +6 ); +if (unlikely (val <0 )) + goto out_sysfs_create_group; +if (smm665_is_critical (val)) + data->co[i] =smm665_convert (val, i); +else + data->ao[i] =smm665_convert (val, i); + } + +/* Register sysfs hooks */ + ret =sysfs_create_group (&client->dev.kobj, &smm665_group); +if (ret) + goto out_sysfs_create_group; + + data->hwmon_dev =hwmon_device_register (&client->dev); +if (IS_ERR (data->hwmon_dev)) { + ret =PTR_ERR (data->hwmon_dev); + goto out_hwmon_device_register; + } + +return 0 ; + +out_hwmon_device_register: +sysfs_remove_group (&client->dev.kobj, &smm665_group); +out_sysfs_create_group: +i2c_unregister_device (data->cmdreg); +out_new_dummy: +kfree (data); +out_kzalloc: +return ret; +} + +static int smm665_remove (struct i2c_client *client) +{ +struct smm665_data *data =i2c_get_clientdata (client);drivers/hwmon/smm665.c line 706
Quoted 10 lines
drivers/hwmon/smm665.c new file +10
-0+ +i2c_unregister_device (data->cmdreg); +hwmon_device_unregister (data->hwmon_dev); +sysfs_remove_group (&client->dev.kobj, &smm665_group); + +kfree (data); + +return 0 ; +} +Personally I'd be cynical. If the other devices you list above should work. I'd add them to the id table and
Kconfigdescription and just put a note saying they are untested.
Quoted 3 lines
Obviously don't do this if you have any reason to suspect they are not fully compatible.
I have no reason to suspect any problems. I'll do that if there are no objections from others.
Since I also wrote a chip simulator driver, I'll be able to do some basic testing, so maybe it is not that much of a problem anyway.
Quoted 27 lines
But then that is me :)
Quoted 25 lines
drivers/hwmon/smm665.c new file +25
-0+static const struct i2c_device_id smm665_id[] = { + {"smm665" ,0 }, + {} +}; + +MODULE_DEVICE_TABLE (i2c, smm665_id); + +/* This is the driver that will be inserted */ +static struct i2c_driver smm665_driver = { + .driver = { + .name ="smm665" , + }, + .probe = smm665_probe, + .remove = smm665_remove, + .id_table = smm665_id, +}; + +static int __init smm665_init (void ) +{ +return i2c_add_driver (&smm665_driver); +} + +static void __exit smm665_exit(void) +{ +i2c_del_driver (&smm665_driver);
Quoted 9 lines
drivers/hwmon/smm665.c line 739
Quoted 8 lines
drivers/hwmon/smm665.c new file +8
-0+} + +MODULE_AUTHOR ("Guenter Roeck" ); +MODULE_DESCRIPTION ("SMM665 driver" ); +MODULE_LICENSE ("GPL" ); + +module_init (smm665_init); +module_exit (smm665_exit);
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
Re: [lm-sensors] [PATCH 1/3] hwmon: Driver for SMM665 Six-Channel
In reply to Guenter RoeckQuoted 24 lines · Jean Delvare
Quoted 14 lines · Guenter Roeck
[...]
Quoted 13 lines
Quoted 13 lines
drivers/hwmon/smm665.c new file +13
-0+/* +* Algorithm for reading ADC, per SMM665 datasheet +* +* {[S][addr][W][Ack]} {[offset][Ack]} {[S][addr][R][Nack]} +* [wait 70 uS] +* {[S][addr][R][Ack]} {[datahi][Ack]} {[datalo][Ack][P]} +* +* To implement the first part of this exchange, +* do a full read transaction and expect a failure/Nack. +* This sets up the address pointer on the SMM665 +* and starts the ADC conversion. +* Then do a two-byte read transaction. +*/ Quoted 2 lines
Quoted 2 lines
Is there no better way of handling this? There are protocol mangling hacks to tell the i2c core to ignore a NAKs under some circumstances.
This is only available on raw I2C messages, not on the higher-level i2c_smbus_*() API. And not all bus drivers support it. And that's not what is needed here anyway: ignoring the nack means we would continue reading from the chip, while it really doesn't want to talk to us at that time.
Quoted 7 lines
Quoted 2 lines
Quoted 2 lines
drivers/hwmon/smm665.c line 188
Quoted 2 lines
drivers/hwmon/smm665.c new file +2
-0+ rv =i2c_smbus_read_byte_data (client, adc <<3 ); +if (rv >=0 ) {You should check for
-ENXIOexplicitly. According toDocumentation/i2c/fault-codes, this is the value bus drivers should return on missing Ack.
Ok, I'll do that. I'll submit a separate patch for the sibyte i2c bus driver since it returns -1 - which is wrong anyway.
Quoted 8 lines
Quoted 8 lines
Quoted 4 lines
drivers/hwmon/smm665.c line 192
Quoted 4 lines
drivers/hwmon/smm665.c new file +4
-0+/* No error, something is wrong. Retry. */ + rv =-1 ; +continue ; + }I looked through the core i2c code, but did not find anything I can use.
Quoted 9 lines
Quoted 4 lines
Problem is that per smm665 specification, the first NACK is expected. So we do not just want to ignore this NACK, we want to actively check if the command "failed" as expected, and report an error if it did _not_ fail.
Do you really have to trigger the Nack for the ADC conversion to start? Can't you just use
i2c_smbus_read_byte()(no_data) for the first part of the transaction?
Unfortunately, yes. It is the only command that works.
Guenter
_______________________________________________
lm-sensors mailing list
[email protected]
http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
PATCH 2/3 hwmon: SMM665 driver documentation
In reply to Guenter Roeck--- Documentation/hwmon/smm665 | 116 ++++++++++++++++++++++++++++++++++++++++++++ 1 files changed, 116 insertions(+), 0 deletions(-) create mode 100644 Documentation/hwmon/smm665
Documentation/hwmon/smm665 new file +116 -0
@@ -0,0 +1,116 @@ +Kernel driver smm665 +========== + +Supported chips: + * Summit Microelectronics SMM665, SMM665B + Prefix: 'smm665' + Addresses scanned: - + Datasheet: Publicly available at the Summit Microelectronics website. + +Author: Guenter Roeck <[email protected]> + + +Description +----------- + +[From datasheet] The SMM665 is an Active DC Output power supply Controller +that monitors, margins and cascade sequences power. The part monitors six +power supply channels as well as VDD, 12V input, two general-purpose analog +inputs and an internal temperature sensor using a 10-bit ADC. + +Each monitored channel has its own high and low limits, plus a critical +limit. + +Usage Notes +----------- + +This driver does not probe for SMM665 devices, since there is no register +which can be safely used to identify the chip. You will have to instantiate +the devices explicitly. When instantiating the device, you have to specify +its configuration register address. + +Example: the following will load the driver for an SMM665 at address 0x57 +on I2C bus #1: +$ modprobe smm665 +$ echo smm665 0x57 > /sys/bus/i2c/devices/i2c-1/new_device + + +Sysfs entries +------------- + +This driver uses the values in the datasheet to convert ADC register values +into the values specified in the sysfs-interface document. All attributes are +read only. + +in1_input 12V input voltage (mV) +in2_input 3.3V (VDD) input voltage (mV) +in3_input Channel A voltage (mV) +in4_input Channel B voltage (mV) +in5_input Channel C voltage (mV) +in6_input Channel D voltage (mV) +in7_input Channel E voltage (mV) +in8_input Channel F voltage (mV) +in9_input AIN1 voltage (mV) +in10_input AIN2 voltage (mV) + +in1_min 12v input minimum voltage (mV) +in2_min 3.3V (VDD) input minimum voltage (mV) +in3_min Channel A minimum voltage (mV) +in4_min Channel B minimum voltage (mV) +in5_min Channel C minimum voltage (mV) +in6_min Channel D minimum voltage (mV) +in7_min Channel E minimum voltage (mV) +in8_min Channel F minimum voltage (mV) +in9_min AIN1 minimum voltage (mV) +in10_min AIN2 minimum voltage (mV) + +in1_min_alarm 12v input undervoltage alarm +in2_min_alarm 3.3V (VDD) input undervoltage alarm +in3_min_alarm Channel A undervoltage alarm +in4_min_alarm Channel B undervoltage alarm +in5_min_alarm Channel C undervoltage alarm +in6_min_alarm Channel D undervoltage alarm +in7_min_alarm Channel E undervoltage alarm +in8_min_alarm Channel F undervoltage alarm +in9_min_alarm AIN1 undervoltage alarm +in10_min_alarm AIN2 undervoltage alarm + +in1_max 12v input maximum voltage (mV) +in2_max 3.3V (VDD) input maximum voltage (mV) +in3_max Channel A maximum voltage (mV) +in4_max Channel B maximum voltage (mV) +in5_max Channel C maximum voltage (mV) +in6_max Channel D maximum voltage (mV) +in7_max Channel E maximum voltage (mV) +in8_max Channel F maximum voltage (mV) +in9_max AIN1 maximum voltage (mV) +in10_max AIN2 maximum voltage (mV) + +in1_max_alarm 12v input overvoltage alarm +in2_max_alarm 3.3V (VDD) input overvoltage alarm +in3_max_alarm Channel A overvoltage alarm +in4_max_alarm Channel B overvoltage alarm +in5_max_alarm Channel C overvoltage alarm +in6_max_alarm Channel D overvoltage alarm +in7_max_alarm Channel E overvoltage alarm +in8_max_alarm Channel F overvoltage alarm +in9_max_alarm AIN1 overvoltage alarm +in10_max_alarm AIN2 overvoltage alarm + +in1_fault 12v input fault +in2_fault 3.3V (VDD) input fault +in3_fault Channel A fault +in4_fault Channel B fault +in5_fault Channel C fault +in6_fault Channel D fault +in7_fault Channel E fault +in8_fault Channel F fault +in9_fault AIN1 fault +in10_fault AIN2 fault + +temp1_input Chip tempererature +temp1_min Mimimum chip tempererature +temp1_max Maximum chip tempererature +temp1_crit Critical chip tempererature +temp1_min_alarm Chip temperature low alarm +temp1_max_alarm Chip temperature high alarm
Signature · 7 lines
1.7.0.87.g0901d _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors
PATCH 3/3 hwmon: Update MAINTAINERS for smm665 driver
In reply to Guenter Roeck--- MAINTAINERS | 7 +++++++ 1 files changed, 7 insertions(+), 0 deletions(-)
MAINTAINERS +7 -0
@@ -5205,6 +5205,13 @@ M: Nicolas Pitre <[email protected]> S: Odd Fixes F: drivers/net/smc91x.* +SMM665 HARDWARE MONITOR DRIVER +M: "Guenter Roeck" <[email protected]> +L: [email protected] +S: Maintained +F: Documentation/hwmon/smm665 +F: drivers/hwmon/smm665.c + SMSC47B397 HARDWARE MONITOR DRIVER M: "Mark M. Hoffman" <[email protected]> L: [email protected]
Signature · 7 lines
1.7.0.87.g0901d _______________________________________________ lm-sensors mailing list [email protected] http://lists.lm-sensors.org/mailman/listinfo/lm-sensors