ks8842: Support 100Mbps when accessed via timberdale
Subsystems (2)
PATCH 1/1 ks8842: Support 100Mbps when accessed via timberdale
This patch removes the code which disabled 100Mbps advertising when the ks8842 is accessed via timberdale.
At higher speed it's good to be nice to the internal state machine in timberdale, by acking interrupts, a write to it's interrupt ack register (IAR).
The flow control setting is removed from TX and RX control registers. Full duplex flow control was not enabled in SGCR3, but we tend to get better performance without flow control.
drivers/net/ks8842.c +14 -12
@@ -34,7 +34,12 @@#define DRV_NAME "ks8842"/* Timberdale specific Registers */ -#define REG_TIMB_RST 0x1c +#define REG_TIMB_RST 0x1c +#define REG_TIMB_FIFO 0x20 +#define REG_TIMB_ISR 0x24 +#define REG_TIMB_IER 0x28 +#define REG_TIMB_IAR 0x2C +#define REQ_TIMB_DMA_RESUME 0x30/* KS8842 registers */
@@ -256,11 +261,8 @@ static void ks8842_reset_hw(struct ks8842_adapter *adapter)/* Enable QMU Transmit flow control / transmit padding / Transmit CRC */ ks8842_write16 (adapter,16 ,0x000E ,REG_TXCR ); -/* enable the receiver, uni + multi + broadcast + flow ctrl -+ crc strip */ -ks8842_write16 (adapter,16 ,0x8 |0x20 |0x40 |0x80 |0x400 , -REG_RXCR ); - +/* enable the receiver, uni + multi + broadcast + crc strip */ +ks8842_write16 (adapter,16 ,0x8 |0x20 |0x40 |0x80 ,REG_RXCR );/* TX frame pointer autoincrement */ ks8842_write16 (adapter,17 ,0x4000 ,REG_TXFDPR );
@@ -276,16 +278,12 @@ static void ks8842_reset_hw(struct ks8842_adapter *adapter)/* enable no excessive collison drop */ ks8842_enable_bits (adapter,32 ,1 <<3 ,REG_SGCR2 ); -/* Enable port 1 force flow control / back pressure / transmit / recv */ -ks8842_write16 (adapter,48 ,0x1E07 ,REG_P1CR2 ); +/* Enable port 1 / back pressure / transmit / recv */ +ks8842_write16 (adapter,48 ,0xE07 ,REG_P1CR2 );/* restart port auto-negotiation */ ks8842_enable_bits (adapter,49 ,1 <<13 ,REG_P1CR4 ); -if (!(adapter->conf_flags &MICREL_KS884X )) -/* only advertise 10Mbps */ -ks8842_clear_bits (adapter,49 ,3 <<2 ,REG_P1CR4 ); -/* Enable the transmitter */ ks8842_enable_tx (adapter);
@@ -543,6 +541,10 @@ void ks8842_tasklet(unsigned long arg)/* Ack */ ks8842_write16 (adapter,18 , isr,REG_ISR ); +if (!(adapter->conf_flags &MICREL_KS884X )) +/* Ack in the timberdale IP as well */ +iowrite32 (0x1 , adapter->hw_addr +REG_TIMB_IAR ); +if (!netif_running (netdev))return ;
David Miller
maintainerFrom: Richard Röjfors <[email protected]>
Date: Sun, 25 Jul 2010 22:55:27 +0200
Quoted 3 lines
The flow control setting is removed from TX and RX control registers. Full duplex flow control was not enabled in SGCR3, but we tend to get better performance without flow control.
Flow control is not just for you, it's for the other end too.
If you're getting bad flow control enabled performance then either:
1) the flow control is configured to kick in too late or too soon
or
2) your ring sizes need adjustment
I'm not applying this patch, flow control is important and should be enabled by default whenever possible. Please instead go try and figure out if flow control trigger points or RX/TX ring sizes need adjustment instead.
Thanks.
Quoted 5 lines · David Miller
I'm not applying this patch, flow control is important and should be enabled by default whenever possible. Please instead go try and figure out if flow control trigger points or RX/TX ring sizes need adjustment instead.
I agree, I will look at the flow control.
--Richard