msm: 8x50: Add SDCC support
Subsystems (3)
PATCH 5/5 msm: 8x50: Add SDCC support
Add platform data and base address for SDCC on QSD8x50. This adds support for slot 1, slot 2 and slot 3.
Signed-off-by Sahitya Tummala <[email protected]>
--- arch/arm/mach-msm/board-qsd8x50.c | 140 ++++++++++++++++ arch/arm/mach-msm/devices-qsd8x50.c | 196 +++++++++++++++++++++++ arch/arm/mach-msm/include/mach/msm_iomap-8x50.h | 8 +- 3 files changed, 340 insertions(+), 4 deletions(-)
arch/arm/mach-msm/board-qsd8x50.c +140 -0
@@ -20,6 +20,7 @@#include <linux/gpio.h> #include <linux/platform_device.h> #include <linux/delay.h> +#include <linux/err.h> #include <asm/mach-types.h> #include <asm/mach/arch.h>
@@ -30,6 +31,8 @@#include <mach/irqs.h> #include <mach/sirc.h> #include <mach/gpio.h> +#include <mach/vreg.h> +#include <mach/mmc.h> #include "devices.h"
@@ -72,6 +75,140 @@ static void msm8x50_init_uart3(void) ARRAY_SIZE(uart3_config_data)); } +#if defined(CONFIG_MMC_MSM ) || defined(CONFIG_MMC_MSM_MODULE ) +static struct vreg *vreg_mmc; + +struct sdcc_gpio { +struct msm_gpio *cfg_data; +uint32_t size; +}; + +static struct msm_gpio sdc1_cfg_data[] = { + {GPIO_CFG (51 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc1_dat_3" }, + {GPIO_CFG (52 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc1_dat_2" }, + {GPIO_CFG (53 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc1_dat_1" }, + {GPIO_CFG (54 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc1_dat_0" }, + {GPIO_CFG (55 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc1_cmd" }, + {GPIO_CFG (56 ,1 ,GPIO_OUTPUT ,GPIO_NO_PULL ,GPIO_8MA ),"sdc1_clk" }, +}; + +static struct msm_gpio sdc2_cfg_data[] = { + {GPIO_CFG (62 ,1 ,GPIO_OUTPUT ,GPIO_NO_PULL ,GPIO_8MA ),"sdc2_clk" }, + {GPIO_CFG (63 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc2_cmd" }, + {GPIO_CFG (64 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc2_dat_3" }, + {GPIO_CFG (65 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc2_dat_2" }, + {GPIO_CFG (66 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc2_dat_1" }, + {GPIO_CFG (67 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc2_dat_0" }, +}; + +static struct msm_gpio sdc3_cfg_data[] = { + {GPIO_CFG (88 ,1 ,GPIO_OUTPUT ,GPIO_NO_PULL ,GPIO_8MA ),"sdc3_clk" }, + {GPIO_CFG (89 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc3_cmd" }, + {GPIO_CFG (90 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc3_dat_3" }, + {GPIO_CFG (91 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc3_dat_2" }, + {GPIO_CFG (92 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc3_dat_1" }, + {GPIO_CFG (93 ,1 ,GPIO_OUTPUT ,GPIO_PULL_UP ,GPIO_8MA ),"sdc3_dat_0" }, +}; + +static struct sdcc_gpio sdcc_cfg_data[] = { + { + .cfg_data = sdc1_cfg_data, + .size =ARRAY_SIZE (sdc1_cfg_data), + }, + { + .cfg_data = sdc2_cfg_data, + .size =ARRAY_SIZE (sdc2_cfg_data), + }, + { + .cfg_data = sdc3_cfg_data, + .size =ARRAY_SIZE (sdc3_cfg_data), + }, +}; + +static unsigned long vreg_sts, gpio_sts; + +static void msm_sdcc_setup_gpio (int dev_id,unsigned int enable) +{ +int rc =0 ; +struct sdcc_gpio *curr; + + curr = &sdcc_cfg_data[dev_id -1 ]; +if (!(test_bit (dev_id, &gpio_sts)^enable)) +return ; + +if (enable) { +set_bit (dev_id, &gpio_sts); + rc =msm_gpios_request_enable (curr->cfg_data, curr->size); +if (rc) +printk (KERN_ERR "%s: Failed to turn on GPIOs for slot %d\n" , + __func__, dev_id); + }else { +clear_bit (dev_id, &gpio_sts); +msm_gpios_disable_free (curr->cfg_data, curr->size); + } +} + +static uint32_t msm_sdcc_setup_power (struct device *dv,unsigned int vdd) +{ +int rc =0 ; +struct platform_device *pdev; + + pdev = container_of(dv, struct platform_device, dev); +msm_sdcc_setup_gpio (pdev->id, !!vdd); + +if (vdd ==0 ) { +if (!vreg_sts) +return 0 ; + +clear_bit (pdev->id, &vreg_sts); + +if (!vreg_sts) { + rc =vreg_disable (vreg_mmc); +if (rc) +printk (KERN_ERR "%s: return val: %d\n" , + __func__, rc); + } +return 0 ; + } + +if (!vreg_sts) { + rc =vreg_set_level (vreg_mmc,2900 ); +if (!rc) + rc =vreg_enable (vreg_mmc); +if (rc) +printk (KERN_ERR "%s: return val: %d\n" , + __func__, rc); + } +set_bit (pdev->id, &vreg_sts); +return 0 ; +} + +static struct msm_mmc_platform_data qsd8x50_sdcc_data = { + .ocr_mask =MMC_VDD_27_28 |MMC_VDD_28_29 , + .translate_vdd = msm_sdcc_setup_power, +}; + +static void __init qsd8x50_init_mmc (void ) +{ +if (machine_is_qsd8x50_ffa () ||machine_is_qsd8x50a_ffa ()) + vreg_mmc =vreg_get (NULL ,"gp6" ); +else + vreg_mmc =vreg_get (NULL ,"gp5" ); + +if (IS_ERR (vreg_mmc)) { +printk (KERN_ERR "%s: vreg get failed (%ld)\n" , + __func__,PTR_ERR (vreg_mmc)); +return ; + } + +msm_add_sdcc (1 , &qsd8x50_sdcc_data,0 ,0 ); +if (machine_is_qsd8x50_surf () ||machine_is_qsd8x50a_surf ()) { +msm_add_sdcc (2 , &qsd8x50_sdcc_data,0 ,0 ); +msm_add_sdcc (3 , &qsd8x50_sdcc_data,0 ,0 ); + } +} +#endif +static void __init qsd8x50_map_io (void ) {msm_map_qsd8x50_io ();
@@ -89,6 +226,9 @@ static void __init qsd8x50_init(void)platform_add_devices (early_devices,ARRAY_SIZE (early_devices));msm8x50_init_uart3 ();platform_add_devices (late_devices,ARRAY_SIZE (late_devices)); +#if defined(CONFIG_MMC_MSM ) || defined(CONFIG_MMC_MSM_MODULE ) +qsd8x50_init_mmc (); +#endif }MACHINE_START (QSD8X50_SURF ,"QCT QSD8X50 SURF" )
arch/arm/mach-msm/devices-qsd8x50.c +196 -0
208 lines not on this page · raw message
arch/arm/mach-msm/include/mach/msm_iomap-8x50.h +4 -4
@@ -132,16 +132,16 @@#define MSM_UART2DM_PHYS 0xA0900000 -#define MSM_SDC1_PHYS 0xA0400000 +#define MSM_SDC1_PHYS 0xA0300000#define MSM_SDC1_SIZE SZ_4K -#define MSM_SDC2_PHYS 0xA0500000 +#define MSM_SDC2_PHYS 0xA0400000#define MSM_SDC2_SIZE SZ_4K -#define MSM_SDC3_PHYS 0xA0600000 +#define MSM_SDC3_PHYS 0xA0500000#define MSM_SDC3_SIZE SZ_4K -#define MSM_SDC4_PHYS 0xA0700000 +#define MSM_SDC4_PHYS 0xA0600000#define MSM_SDC4_SIZE SZ_4K#endif
Signature · 5 lines
1.7.1 -- Consultant for Qualcomm Innovation Center, Inc. Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum.