POWER: BQ27x00: New Properties, fixes, bq27000 support
cover POWER: BQ27x00: New Properties, fixes, bq27000 support
This patch series contains a few updates for the bq27x00 driver:
* Support for additional power supply properties
* Support for the bq27000 battery which is identical to the bq27200 but is connected through the HDQ bus.
* Adds a register cache to the driver and introduces polling the batteries state
* Minor improvements and cleanups
The last patch in this series is not specific to the bq27x00 driver but is required for uevents to be generated properly for this driver. The patch makes properties which return -ENODATA to be ignored when generating uevents. Previously in such a case uevent generation would have been aborted with an error. But since the bq27x00 return -ENODATA for the TIME_TO_FULL property when the battery is not charging and for the TIME_TO_EMPTY property when the battery is not discharging and at least one of them is always true uevent generation would always fail.
This series has so far been tested with the bq27000 and the bq27200 battery, but not with the bq27500 battery, so it would be nice if somebody with a board containing such a battery could test the patches to make sure that there are no regressions.
Lars-Peter Clausen (10):
POWER: bq27x00: Add type property
POWER: bq27x00: Improve temperature precession
POWER: bq27x00: Return -ENODEV for properties if the battery is not
present
POWER: bq27x00: Prepare code for addition of bq27000 platform driver
POWER: bq27x00: Add bq27000 support
POWER: bq27X00: Cache battery registers
POWER: bq27x00: Poll battery state
POWER: bq27x00: Give more specific reports on battery status
POWER: bq27x00: Cleanup bq27x00_i2c_read
POWER: Ignore -ENODATA errors when generating a uevent
Pali Rohár (4):
POWER: bq27x00: Fix current now property
POWER: bq27x00: Add new properties
POWER: bq27x00: Add MODULE_DEVICE_TABLE
POWER: bq27x00: Minor cleanups
drivers/power/Kconfig | 14 + drivers/power/bq27x00_battery.c | 725 +++++++++++++++++++++++++-------- drivers/power/power_supply_sysfs.c | 2 +- include/linux/power/bq27x00_battery.h | 19 + 4 files changed, 590 insertions(+), 170 deletions(-) create mode 100644 include/linux/power/bq27x00_battery.h
Signature · 1 line
1.7.2.3
PATCH 1/14 POWER: bq27x00: Add type property
This patch adds the type property to the bq27x00 battery driver. All bq27x00 are lithium ion batteries.
--- drivers/power/bq27x00_battery.c | 4 ++++ 1 files changed, 4 insertions(+), 0 deletions(-)
drivers/power/bq27x00_battery.c +4 -0
@@ -78,6 +78,7 @@ static enum power_supply_property bq27x00_battery_props[] = {POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW ,POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG ,POWER_SUPPLY_PROP_TIME_TO_FULL_NOW , + POWER_SUPPLY_PROP_TECHNOLOGY, };/*
@@ -277,6 +278,9 @@ static int bq27x00_battery_get_property(struct power_supply *psy,case POWER_SUPPLY_PROP_TIME_TO_FULL_NOW : ret =bq27x00_battery_time (di, BQ27x00_REG_TTF, val);break ; +case POWER_SUPPLY_PROP_TECHNOLOGY : + val->intval =POWER_SUPPLY_TECHNOLOGY_LION ; +break ;default :return -EINVAL ; }
Signature · 1 line
1.7.2.3
Re: [PATCH 01/14] POWER: bq27x00: Add type property
Quoted 33 lines · Lars-Peter Clausen
This patch adds the type property to the bq27x00 battery driver. All bq27x00 are lithium ion batteries.
Signed-off-by Lars-Peter Clausen <[email protected]>--- drivers/power/bq27x00_battery.c | 4 ++++ 1 files changed, 4 insertions(+), 0 deletions(-)drivers/power/bq27x00_battery.c +4
-0@@ -78,6 +78,7 @@ static enum power_supply_property bq27x00_battery_props[] = {POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW ,POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG ,POWER_SUPPLY_PROP_TIME_TO_FULL_NOW , + POWER_SUPPLY_PROP_TECHNOLOGY, };/* @@ -277,6 +278,9 @@ static int bq27x00_battery_get_property(struct power_supply *psy,case POWER_SUPPLY_PROP_TIME_TO_FULL_NOW : ret =bq27x00_battery_time (di, BQ27x00_REG_TTF, val);break ; +case POWER_SUPPLY_PROP_TECHNOLOGY : + val->intval =POWER_SUPPLY_TECHNOLOGY_LION ; +break ;default :return -EINVAL ; }Signature · 1 line
1.7.2.3
Signature · 5 lines
GNU/Linux Solutions e-mail: [email protected] Linux Device Driver [email protected] Embedded Systems phone: +39 349 2432127 UNIX programming skype: rodolfo.giometti Freelance ICT Italia - Consulente ICT Italia - www.consulenti-ict.it
PATCH 2/14 POWER: bq27x00: Improve temperature precession
In reply to Lars-Peter ClausenThis patch improves the precession of the temperature property of the bq27x00 driver.
By dividing before multiplying the current code effectively cuts of the last decimal digit. This patch fixes it by multiplying before dividing.
--- drivers/power/bq27x00_battery.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
drivers/power/bq27x00_battery.c +1 -1
@@ -109,7 +109,7 @@ static int bq27x00_battery_temperature(struct bq27x00_device_info *di)if (di->chip ==BQ27500 )return temp -2731 ;else -return ((temp >>2 ) -273 ) *10 ; +return ((temp *5 ) -5463 ) /2 ; }/*
Signature · 1 line
1.7.2.3
Re: [PATCH 02/14] POWER: bq27x00: Improve temperature precession
Quoted 25 lines · Lars-Peter Clausen
This patch improves the precession of the temperature property of the bq27x00 driver.
By dividing before multiplying the current code effectively cuts of the last decimal digit. This patch fixes it by multiplying before dividing.Signed-off-by Lars-Peter Clausen <[email protected]>--- drivers/power/bq27x00_battery.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)drivers/power/bq27x00_battery.c +1
-1@@ -109,7 +109,7 @@ static int bq27x00_battery_temperature(struct bq27x00_device_info *di)if (di->chip ==BQ27500 )return temp -2731 ;else -return ((temp >>2 ) -273 ) *10 ; +return ((temp *5 ) -5463 ) /2 ; }/* Signature · 1 line
1.7.2.3
Signature · 5 lines
GNU/Linux Solutions e-mail: [email protected] Linux Device Driver [email protected] Embedded Systems phone: +39 349 2432127 UNIX programming skype: rodolfo.giometti Freelance ICT Italia - Consulente ICT Italia - www.consulenti-ict.it
PATCH 3/14 POWER: bq27x00: Fix current now property
In reply to Lars-Peter ClausenFrom: Pali Rohár <[email protected]>
According to the bq27000 datasheet to obtain the current value in Micro-ampere from the AI register it has to be transformed by the following formula:
current = AI * 3570 / 20
This patch adjust the drivers code accordingly.
--- drivers/power/bq27x00_battery.c | 7 +++++-- 1 files changed, 5 insertions(+), 2 deletions(-)
drivers/power/bq27x00_battery.c +5 -2
@@ -44,6 +44,8 @@#define BQ27500_FLAG_DSC BIT(0)#define BQ27500_FLAG_FC BIT(9) +#define BQ27000_RS 20/* Resistor sense */ +/* If the system has several batteries we need a different name for each * of them... */
@@ -149,7 +151,7 @@ static int bq27x00_battery_current(struct bq27x00_device_info *di)if (di->chip ==BQ27500 ) {/* bq27500 returns signed value */ - curr = (int )(s16 )curr; + curr = (int )((s16 )curr) *1000 ; }else { ret =bq27x00_read (BQ27x00_REG_FLAGS, &flags,0 , di);if (ret <0 ) {
@@ -160,9 +162,10 @@ static int bq27x00_battery_current(struct bq27x00_device_info *di)dev_dbg (di->dev,"negative current!\n" ); curr = -curr; } + curr = curr *3570 /BQ27000_RS ; } -return curr *1000 ; +return curr; }/*
Signature · 1 line
1.7.2.3
Re: [PATCH 03/14] POWER: bq27x00: Fix current now property
Quoted 51 lines · Lars-Peter Clausen
From: Pali Rohár <[email protected]>
According to the bq27000 datasheet to obtain the current value in Micro-ampere from the AI register it has to be transformed by the following formula:
current = AI * 3570 / 20This patch adjust the drivers code accordingly.
Signed-off-by Pali Rohár <[email protected]>Signed-off-by Lars-Peter Clausen <[email protected]>--- drivers/power/bq27x00_battery.c | 7 +++++-- 1 files changed, 5 insertions(+), 2 deletions(-)drivers/power/bq27x00_battery.c +5
-2@@ -44,6 +44,8 @@#define BQ27500_FLAG_DSC BIT(0)#define BQ27500_FLAG_FC BIT(9) +#define BQ27000_RS 20/* Resistor sense */ +/* If the system has several batteries we need a different name for each * of them... */ @@ -149,7 +151,7 @@ static int bq27x00_battery_current(struct bq27x00_device_info *di)if (di->chip ==BQ27500 ) {/* bq27500 returns signed value */ - curr = (int )(s16 )curr; + curr = (int )((s16 )curr) *1000 ; }else { ret =bq27x00_read (BQ27x00_REG_FLAGS, &flags,0 , di);if (ret <0 ) {@@ -160,9 +162,10 @@ static int bq27x00_battery_current(struct bq27x00_device_info *di)dev_dbg (di->dev,"negative current!\n" ); curr = -curr; } + curr = curr *3570 /BQ27000_RS ; } -return curr *1000 ; +return curr; }/* Signature · 1 line
1.7.2.3
Signature · 5 lines
GNU/Linux Solutions e-mail: [email protected] Linux Device Driver [email protected] Embedded Systems phone: +39 349 2432127 UNIX programming skype: rodolfo.giometti Freelance ICT Italia - Consulente ICT Italia - www.consulenti-ict.it
PATCH 4/14 POWER: bq27x00: Return -ENODEV for properties if the battery is not present
In reply to Lars-Peter ClausenThis patch changes get_property callback of the bq27x00 battery to return -ENODEV for properties other then the PROP_PRESENT if the battery is not present.
The power subsystem core expects a driver to behave that way.
--- drivers/power/bq27x00_battery.c | 9 +++++++-- 1 files changed, 7 insertions(+), 2 deletions(-)
drivers/power/bq27x00_battery.c +7 -2
@@ -252,16 +252,21 @@ static int bq27x00_battery_get_property(struct power_supply *psy, {int ret =0 ;struct bq27x00_device_info *di =to_bq27x00_device_info (psy); +int voltage =bq27x00_battery_voltage (di); + +if (psp !=POWER_SUPPLY_PROP_PRESENT && voltage <=0 ) +return -ENODEV ;switch (psp) {case POWER_SUPPLY_PROP_STATUS : ret =bq27x00_battery_status (di, val);break ;case POWER_SUPPLY_PROP_VOLTAGE_NOW : + val->intval = voltage; +break ;case POWER_SUPPLY_PROP_PRESENT : - val->intval =bq27x00_battery_voltage (di);if (psp ==POWER_SUPPLY_PROP_PRESENT ) - val->intval = val->intval <=0 ?0 :1 ; + val->intval = voltage <=0 ?0 :1 ;break ;case POWER_SUPPLY_PROP_CURRENT_NOW : val->intval =bq27x00_battery_current (di);
Signature · 1 line
1.7.2.3
Re: [PATCH 04/14] POWER: bq27x00: Return -ENODEV for properties if the battery is not present
Quoted 41 lines · Lars-Peter Clausen
This patch changes
get_propertycallback of the bq27x00 battery to return-ENODEVfor properties other then thePROP_PRESENTif the battery is not present.
The power subsystem core expects a driver to behave that way.Signed-off-by Lars-Peter Clausen <[email protected]>--- drivers/power/bq27x00_battery.c | 9 +++++++-- 1 files changed, 7 insertions(+), 2 deletions(-)drivers/power/bq27x00_battery.c +7
-2@@ -252,16 +252,21 @@ static int bq27x00_battery_get_property(struct power_supply *psy, {int ret =0 ;struct bq27x00_device_info *di =to_bq27x00_device_info (psy); +int voltage =bq27x00_battery_voltage (di); + +if (psp !=POWER_SUPPLY_PROP_PRESENT && voltage <=0 ) +return -ENODEV ;switch (psp) {case POWER_SUPPLY_PROP_STATUS : ret =bq27x00_battery_status (di, val);break ;case POWER_SUPPLY_PROP_VOLTAGE_NOW : + val->intval = voltage; +break ;case POWER_SUPPLY_PROP_PRESENT : - val->intval =bq27x00_battery_voltage (di);if (psp ==POWER_SUPPLY_PROP_PRESENT ) - val->intval = val->intval <=0 ?0 :1 ; + val->intval = voltage <=0 ?0 :1 ;break ;case POWER_SUPPLY_PROP_CURRENT_NOW : val->intval =bq27x00_battery_current (di);Signature · 1 line
1.7.2.3
Signature · 5 lines
GNU/Linux Solutions e-mail: [email protected] Linux Device Driver [email protected] Embedded Systems phone: +39 349 2432127 UNIX programming skype: rodolfo.giometti Freelance ICT Italia - Consulente ICT Italia - www.consulenti-ict.it
PATCH 5/14 POWER: bq27x00: Prepare code for addition of bq27000 platform driver
In reply to Lars-Peter ClausenThis patch simplifies the drivers data structure and moves code to be shared by both init functions into a common function.
This patch has no functional changes, it only moves code around.
--- drivers/power/bq27x00_battery.c | 86 +++++++++++++++++--------------------- 1 files changed, 39 insertions(+), 47 deletions(-)
drivers/power/bq27x00_battery.c +39 -47
@@ -54,8 +54,8 @@ static DEFINE_MUTEX(battery_mutex);struct bq27x00_device_info ;struct bq27x00_access_methods { -int (*read)(u8 reg,int *rt_value,int b_single, -struct bq27x00_device_info *di); +int (*read)(struct bq27x00_device_info *,u8 reg,int *rt_value, +bool single); };enum bq27x00_chip {BQ27000 ,BQ27500 };
@@ -63,11 +63,11 @@ enum bq27x00_chip { BQ27000, BQ27500 };struct bq27x00_device_info {struct device *dev;int id; -struct bq27x00_access_methods *bus; -struct power_supply bat;enum bq27x00_chip chip; -struct i2c_client *client; +struct power_supply bat; + +struct bq27x00_access_methods bus; };static enum power_supply_property bq27x00_battery_props[] = {
@@ -87,10 +87,10 @@ static enum power_supply_property bq27x00_battery_props[] = {* Common code for BQ27x00 devices */ -static int bq27x00_read (u8 reg,int *rt_value,int b_single, -struct bq27x00_device_info *di) +static inline int bq27x00_read (struct bq27x00_device_info *di,u8 reg, +int *rt_value,bool single) { -return di->bus->read (reg, rt_value, b_single, di); +return di->bus.read (di, reg, rt_value, single); }/*
@@ -102,7 +102,7 @@ static int bq27x00_battery_temperature(struct bq27x00_device_info *di)int ret;int temp =0 ; - ret =bq27x00_read (BQ27x00_REG_TEMP, &temp,0 , di); + ret =bq27x00_read (di, BQ27x00_REG_TEMP, &temp, false);if (ret) {dev_err (di->dev,"error reading temperature\n" );return ret;
@@ -123,7 +123,7 @@ static int bq27x00_battery_voltage(struct bq27x00_device_info *di)int ret;int volt =0 ; - ret =bq27x00_read (BQ27x00_REG_VOLT, &volt,0 , di); + ret =bq27x00_read (di, BQ27x00_REG_VOLT, &volt, false);if (ret) {dev_err (di->dev,"error reading voltage\n" );return ret;
@@ -143,7 +143,7 @@ static int bq27x00_battery_current(struct bq27x00_device_info *di)int curr =0 ;int flags =0 ; - ret =bq27x00_read (BQ27x00_REG_AI, &curr,0 , di); + ret =bq27x00_read (di, BQ27x00_REG_AI, &curr, false);if (ret) {dev_err (di->dev,"error reading current\n" );return 0 ;
@@ -153,7 +153,7 @@ static int bq27x00_battery_current(struct bq27x00_device_info *di)/* bq27500 returns signed value */ curr = (int )((s16 )curr) *1000 ; }else { - ret =bq27x00_read (BQ27x00_REG_FLAGS, &flags,0 , di); + ret =bq27x00_read (di, BQ27x00_REG_FLAGS, &flags, false);if (ret <0 ) {dev_err (di->dev,"error reading flags\n" );return 0 ;
@@ -178,9 +178,9 @@ static int bq27x00_battery_rsoc(struct bq27x00_device_info *di)int rsoc =0 ;if (di->chip ==BQ27500 ) - ret =bq27x00_read (BQ27500_REG_SOC , &rsoc,0 , di); + ret =bq27x00_read (di,BQ27500_REG_SOC , &rsoc, false);else - ret =bq27x00_read (BQ27000_REG_RSOC , &rsoc,1 , di); + ret =bq27x00_read (di,BQ27000_REG_RSOC , &rsoc, true);if (ret) {dev_err (di->dev,"error reading relative State-of-Charge\n" );return ret;
@@ -196,7 +196,7 @@ static int bq27x00_battery_status(struct bq27x00_device_info *di,int status;int ret; - ret =bq27x00_read (BQ27x00_REG_FLAGS, &flags,0 , di); + ret =bq27x00_read (di, BQ27x00_REG_FLAGS, &flags, false);if (ret <0 ) {dev_err (di->dev,"error reading flags\n" );return ret;
@@ -230,7 +230,7 @@ static int bq27x00_battery_time(struct bq27x00_device_info *di, int reg,int tval =0 ;int ret; - ret =bq27x00_read (reg, &tval,0 , di); + ret =bq27x00_read (reg, &tval, false);if (ret) {dev_err (di->dev,"error reading register %02x\n" , reg);return ret;
@@ -296,23 +296,35 @@ static int bq27x00_battery_get_property(struct power_supply *psy,return ret; } -static void bq27x00_powersupply_init (struct bq27x00_device_info *di) +static int bq27x00_powersupply_init (struct bq27x00_device_info *di) { +int ret; + di->bat.type =POWER_SUPPLY_TYPE_BATTERY ; di->bat.properties = bq27x00_battery_props; di->bat.num_properties =ARRAY_SIZE (bq27x00_battery_props); di->bat.get_property = bq27x00_battery_get_property; di->bat.external_power_changed =NULL ; + + ret =power_supply_register (di->dev, &di->bat); +if (ret) { +dev_err (di->dev,"failed to register battery: %d\n" , ret); +return ret; + } + +dev_info (di->dev,"support ver. %s enabled\n" ,DRIVER_VERSION ); + +return 0 ; }/* * i2c specific code */ -static int bq27x00_read_i2c (u8 reg,int *rt_value,int b_single, -struct bq27x00_device_info *di) +static int bq27x00_read_i2c (struct bq27x00_device_info *di,u8 reg, +int *rt_value,bool single) { -struct i2c_client *client = di->client; +struct i2c_client *client =to_i2c_client (di->dev);struct i2c_msg msg[1 ];unsigned char data[2 ];int err;
@@ -329,7 +341,7 @@ static int bq27x00_read_i2c(u8 reg, int *rt_value, int b_single, err =i2c_transfer (client->adapter, msg,1 );if (err >=0 ) { -if (!b_single) +if (!single) msg->len =2 ;else msg->len =1 ;
@@ -337,7 +349,7 @@ static int bq27x00_read_i2c(u8 reg, int *rt_value, int b_single, msg->flags =I2C_M_RD ; err =i2c_transfer (client->adapter, msg,1 );if (err >=0 ) { -if (!b_single) +if (!single) *rt_value =get_unaligned_le16 (data);else *rt_value = data[0 ];
@@ -353,7 +365,6 @@ static int bq27x00_battery_probe(struct i2c_client *client, {char *name;struct bq27x00_device_info *di; -struct bq27x00_access_methods *bus;int num;int retval =0 ;
@@ -380,38 +391,20 @@ static int bq27x00_battery_probe(struct i2c_client *client, retval = -ENOMEM ; goto batt_failed_2; } + di->id = num; + di->dev = &client->dev; di->chip = id->driver_data; + di->bat.name = name; + di->bus.read = &bq27x00_read_i2c; - bus =kzalloc (sizeof (*bus),GFP_KERNEL ); -if (!bus) { -dev_err (&client->dev,"failed to allocate access method " -"data\n" ); - retval = -ENOMEM ; +if (bq27x00_powersupply_init (di)) goto batt_failed_3; - }i2c_set_clientdata (client, di); - di->dev = &client->dev; - di->bat.name = name; - bus->read = &bq27x00_read_i2c; - di->bus = bus; - di->client = client; - -bq27x00_powersupply_init (di); - - retval =power_supply_register (&client->dev, &di->bat); -if (retval) { -dev_err (&client->dev,"failed to register battery\n" ); - goto batt_failed_4; - } - -dev_info (&client->dev,"support ver. %s enabled\n" ,DRIVER_VERSION );return 0 ; -batt_failed_4: -kfree (bus); batt_failed_3:kfree (di); batt_failed_2:
@@ -430,7 +423,6 @@ static int bq27x00_battery_remove(struct i2c_client *client)power_supply_unregister (&di->bat); -kfree (di->bus);kfree (di->bat.name);mutex_lock (&battery_mutex);
Signature · 1 line
1.7.2.3
Re: [PATCH 05/14] POWER: bq27x00: Prepare code for addition of bq27000 platform driver
Quoted 240 lines · Lars-Peter Clausen
This patch simplifies the drivers data structure and moves code to be shared by both init functions into a common function.
This patch has no functional changes, it only moves code around.Signed-off-by Lars-Peter Clausen <[email protected]>--- drivers/power/bq27x00_battery.c | 86 +++++++++++++++++--------------------- 1 files changed, 39 insertions(+), 47 deletions(-)drivers/power/bq27x00_battery.c +39
-47@@ -54,8 +54,8 @@ static DEFINE_MUTEX(battery_mutex);struct bq27x00_device_info ;struct bq27x00_access_methods { -int (*read)(u8 reg,int *rt_value,int b_single, -struct bq27x00_device_info *di); +int (*read)(struct bq27x00_device_info *,u8 reg,int *rt_value, +bool single); };enum bq27x00_chip {BQ27000 ,BQ27500 };@@ -63,11 +63,11 @@ enum bq27x00_chip { BQ27000, BQ27500 };struct bq27x00_device_info {struct device *dev;int id; -struct bq27x00_access_methods *bus; -struct power_supply bat;enum bq27x00_chip chip; -struct i2c_client *client; +struct power_supply bat; + +struct bq27x00_access_methods bus; };static enum power_supply_property bq27x00_battery_props[] = {@@ -87,10 +87,10 @@ static enum power_supply_property bq27x00_battery_props[] = {* Common code for BQ27x00 devices */ -static int bq27x00_read (u8 reg,int *rt_value,int b_single, -struct bq27x00_device_info *di) +static inline int bq27x00_read (struct bq27x00_device_info *di,u8 reg, +int *rt_value,bool single) { -return di->bus->read (reg, rt_value, b_single, di); +return di->bus.read (di, reg, rt_value, single); }/* @@ -102,7 +102,7 @@ static int bq27x00_battery_temperature(struct bq27x00_device_info *di)int ret;int temp =0 ; - ret =bq27x00_read (BQ27x00_REG_TEMP, &temp,0 , di); + ret =bq27x00_read (di, BQ27x00_REG_TEMP, &temp, false);if (ret) {dev_err (di->dev,"error reading temperature\n" );return ret;@@ -123,7 +123,7 @@ static int bq27x00_battery_voltage(struct bq27x00_device_info *di)int ret;int volt =0 ; - ret =bq27x00_read (BQ27x00_REG_VOLT, &volt,0 , di); + ret =bq27x00_read (di, BQ27x00_REG_VOLT, &volt, false);if (ret) {dev_err (di->dev,"error reading voltage\n" );return ret;@@ -143,7 +143,7 @@ static int bq27x00_battery_current(struct bq27x00_device_info *di)int curr =0 ;int flags =0 ; - ret =bq27x00_read (BQ27x00_REG_AI, &curr,0 , di); + ret =bq27x00_read (di, BQ27x00_REG_AI, &curr, false);if (ret) {dev_err (di->dev,"error reading current\n" );return 0 ;@@ -153,7 +153,7 @@ static int bq27x00_battery_current(struct bq27x00_device_info *di)/* bq27500 returns signed value */ curr = (int )((s16 )curr) *1000 ; }else { - ret =bq27x00_read (BQ27x00_REG_FLAGS, &flags,0 , di); + ret =bq27x00_read (di, BQ27x00_REG_FLAGS, &flags, false);if (ret <0 ) {dev_err (di->dev,"error reading flags\n" );return 0 ;@@ -178,9 +178,9 @@ static int bq27x00_battery_rsoc(struct bq27x00_device_info *di)int rsoc =0 ;if (di->chip ==BQ27500 ) - ret =bq27x00_read (BQ27500_REG_SOC , &rsoc,0 , di); + ret =bq27x00_read (di,BQ27500_REG_SOC , &rsoc, false);else - ret =bq27x00_read (BQ27000_REG_RSOC , &rsoc,1 , di); + ret =bq27x00_read (di,BQ27000_REG_RSOC , &rsoc, true);if (ret) {dev_err (di->dev,"error reading relative State-of-Charge\n" );return ret;@@ -196,7 +196,7 @@ static int bq27x00_battery_status(struct bq27x00_device_info *di,int status;int ret; - ret =bq27x00_read (BQ27x00_REG_FLAGS, &flags,0 , di); + ret =bq27x00_read (di, BQ27x00_REG_FLAGS, &flags, false);if (ret <0 ) {dev_err (di->dev,"error reading flags\n" );return ret;@@ -230,7 +230,7 @@ static int bq27x00_battery_time(struct bq27x00_device_info *di, int reg,int tval =0 ;int ret; - ret =bq27x00_read (reg, &tval,0 , di); + ret =bq27x00_read (reg, &tval, false);if (ret) {dev_err (di->dev,"error reading register %02x\n" , reg);return ret;@@ -296,23 +296,35 @@ static int bq27x00_battery_get_property(struct power_supply *psy,return ret; } -static void bq27x00_powersupply_init (struct bq27x00_device_info *di) +static int bq27x00_powersupply_init (struct bq27x00_device_info *di) { +int ret; + di->bat.type =POWER_SUPPLY_TYPE_BATTERY ; di->bat.properties = bq27x00_battery_props; di->bat.num_properties =ARRAY_SIZE (bq27x00_battery_props); di->bat.get_property = bq27x00_battery_get_property; di->bat.external_power_changed =NULL ; + + ret =power_supply_register (di->dev, &di->bat); +if (ret) { +dev_err (di->dev,"failed to register battery: %d\n" , ret); +return ret; + } + +dev_info (di->dev,"support ver. %s enabled\n" ,DRIVER_VERSION ); + +return 0 ; }/* * i2c specific code */ -static int bq27x00_read_i2c (u8 reg,int *rt_value,int b_single, -struct bq27x00_device_info *di) +static int bq27x00_read_i2c (struct bq27x00_device_info *di,u8 reg, +int *rt_value,bool single) { -struct i2c_client *client = di->client; +struct i2c_client *client =to_i2c_client (di->dev);struct i2c_msg msg[1 ];unsigned char data[2 ];int err;@@ -329,7 +341,7 @@ static int bq27x00_read_i2c(u8 reg, int *rt_value, int b_single, err =i2c_transfer (client->adapter, msg,1 );if (err >=0 ) { -if (!b_single) +if (!single) msg->len =2 ;else msg->len =1 ;@@ -337,7 +349,7 @@ static int bq27x00_read_i2c(u8 reg, int *rt_value, int b_single, msg->flags =I2C_M_RD ; err =i2c_transfer (client->adapter, msg,1 );if (err >=0 ) { -if (!b_single) +if (!single) *rt_value =get_unaligned_le16 (data);else *rt_value = data[0 ];@@ -353,7 +365,6 @@ static int bq27x00_battery_probe(struct i2c_client *client, {char *name;struct bq27x00_device_info *di; -struct bq27x00_access_methods *bus;int num;int retval =0 ;@@ -380,38 +391,20 @@ static int bq27x00_battery_probe(struct i2c_client *client, retval = -ENOMEM ; goto batt_failed_2; } + di->id = num; + di->dev = &client->dev; di->chip = id->driver_data; + di->bat.name = name; + di->bus.read = &bq27x00_read_i2c; - bus =kzalloc (sizeof (*bus),GFP_KERNEL ); -if (!bus) { -dev_err (&client->dev,"failed to allocate access method " -"data\n" ); - retval = -ENOMEM ; +if (bq27x00_powersupply_init (di)) goto batt_failed_3; - }i2c_set_clientdata (client, di); - di->dev = &client->dev; - di->bat.name = name; - bus->read = &bq27x00_read_i2c; - di->bus = bus; - di->client = client; - -bq27x00_powersupply_init (di); - - retval =power_supply_register (&client->dev, &di->bat); -if (retval) { -dev_err (&client->dev,"failed to register battery\n" ); - goto batt_failed_4; - } - -dev_info (&client->dev,"support ver. %s enabled\n" ,DRIVER_VERSION );return 0 ; -batt_failed_4: -kfree (bus); batt_failed_3:kfree (di); batt_failed_2:@@ -430,7 +423,6 @@ static int bq27x00_battery_remove(struct i2c_client *client)power_supply_unregister (&di->bat); -kfree (di->bus);kfree (di->bat.name);mutex_lock (&battery_mutex);Signature · 1 line
1.7.2.3
Signature · 5 lines
GNU/Linux Solutions e-mail: [email protected] Linux Device Driver [email protected] Embedded Systems phone: +39 349 2432127 UNIX programming skype: rodolfo.giometti Freelance ICT Italia - Consulente ICT Italia - www.consulenti-ict.it
PATCH 6/14 POWER: bq27x00: Add bq27000 support
In reply to Lars-Peter ClausenThis patch adds support for the bq27000 battery to the bq27x00 driver. The bq27000 is similar to the bq27200 except that it uses the HDQ bus instead of I2C to communicate with the host system.
The driver is implemented as a platform driver. The driver expects to be provided with a read callback function through its platform data. The read function is assumed to do the lowlevel HDQ handling and read out the value of a certain register.
--- drivers/power/Kconfig | 14 +++ drivers/power/bq27x00_battery.c | 184 ++++++++++++++++++++++++++++++--- include/linux/power/bq27x00_battery.h | 19 ++++ 3 files changed, 202 insertions(+), 15 deletions(-) create mode 100644 include/linux/power/bq27x00_battery.h
drivers/power/Kconfig +14 -0
@@ -117,10 +117,24 @@ config BATTERY_BQ20Z75 config BATTERY_BQ27x00 tristate "BQ27x00 battery driver" + help + Say Y here to enable support for batteries with BQ27x00 (I2C/HDQ) chips. + +config BATTERY_BQ27X00_I2C + bool "BQ27200/BQ27500 support" + depends on BATTERY_BQ27x00 depends on I2C + default y help Say Y here to enable support for batteries with BQ27x00 (I2C) chips. +config BATTERY_BQ27X00_PLATFORM + bool "BQ27000 support" + depends on BATTERY_BQ27x00 + default y + help + Say Y here to enable support for batteries with BQ27000 (HDQ) chips. + config BATTERY_DA9030 tristate "DA9030 battery driver" depends on PMIC_DA903X
drivers/power/bq27x00_battery.c +169 -15
232 lines not on this page · raw message
include/linux/power/bq27x00_battery.h new file +19 -0
@@ -0,0 +1,19 @@ +#ifndef __LINUX_BQ27X00_BATTERY_H__ +#define __LINUX_BQ27X00_BATTERY_H__ + +/** +* struct bq27000_plaform_data - Platform data for bq27000 devices +* @name: Name of the battery. If NULL the driver will fallback to "bq27000". +* @read: HDQ read callback. +* This function should provide access to the HDQ bus the battery is +* connected to. +* The first parameter is a pointer to the battery device, the second the +* register to be read. The return value should either be the content of +* the passed register or an error value. +*/ +struct bq27000_platform_data { +const char *name; +int (*read)(struct device *dev,unsigned int ); +}; + +#endif
Signature · 1 line
1.7.2.3
PATCH 7/14 POWER: bq27X00: Cache battery registers
In reply to Lars-Peter ClausenThis patch adds a register cache to the bq27x00 battery driver. Usually multiple, if not all, power_supply properties are queried at once, for example when an uevent is generated. Since some registers are used by multiple properties caching the registers should reduce the number of reads.
Furthermore the registers of the bq27x00 are only updated at discrete intervals, for how long the cache is valid is set to roughly match the batteries internal update interval.
It will also be used in the follow up patch to check if the battery status has been changed since the last update to emit power_supply_changed events.
--- drivers/power/bq27x00_battery.c | 263 +++++++++++++++++++++----------------- 1 files changed, 145 insertions(+), 118 deletions(-)
drivers/power/bq27x00_battery.c +145 -118
@@ -19,7 +19,6 @@#include <linux/module.h> #include <linux/param.h> #include <linux/jiffies.h> -#include <linux/workqueue.h> #include <linux/delay.h> #include <linux/platform_device.h> #include <linux/power_supply.h>
@@ -51,17 +50,31 @@struct bq27x00_device_info ;struct bq27x00_access_methods { -int (*read)(struct bq27x00_device_info *,u8 reg,int *rt_value, -bool single); +int (*read)(struct bq27x00_device_info *di,u8 reg,bool single); };enum bq27x00_chip {BQ27000 ,BQ27500 }; +struct bq27x00_reg_cache { +int temperature; +int time_to_empty; +int time_to_empty_avg; +int time_to_full; +int capacity; +int flags; + +int voltage; +int current_now; +}; +struct bq27x00_device_info {struct device *dev;int id;enum bq27x00_chip chip; +struct bq27x00_reg_cache cache; +unsigned long last_update; +struct power_supply bat;struct bq27x00_access_methods bus;
@@ -85,48 +98,107 @@ static enum power_supply_property bq27x00_battery_props[] = {*/ static inline int bq27x00_read (struct bq27x00_device_info *di,u8 reg, -int *rt_value,bool single) +bool single) { -return di->bus.read (di, reg, rt_value, single); +return di->bus.read (di, reg, single); }/* -* Return the battery temperature in tenths of degree Celsius +* Return the battery Voltage in milivolts * Or < 0 if something fails. */ -static int bq27x00_battery_temperature (struct bq27x00_device_info *di) +static int bq27x00_battery_read_voltage (struct bq27x00_device_info *di) { -int ret; -int temp =0 ; +int volt; - ret =bq27x00_read (di, BQ27x00_REG_TEMP, &temp, false); -if (ret) { -dev_err (di->dev,"error reading temperature\n" ); -return ret; - } + volt =bq27x00_read (di, BQ27x00_REG_VOLT, false); +if (volt <0 ) +return volt; + +return volt *1000 ; +} + +/* +* Return the battery Relative State-of-Charge +* Or < 0 if something fails. +*/ +static int bq27x00_battery_read_rsoc (struct bq27x00_device_info *di) +{ +int rsoc;if (di->chip ==BQ27500 ) -return temp -2731 ; + rsoc =bq27x00_read (di,BQ27500_REG_SOC , false);else -return ((temp *5 ) -5463 ) /2 ; + rsoc =bq27x00_read (di,BQ27000_REG_RSOC , true); + +if (rsoc <0 ) +dev_err (di->dev,"error reading relative State-of-Charge\n" ); + +return rsoc; }/* -* Return the battery Voltage in milivolts -* Or < 0 if something fails. +* Read a time register. +* Return < 0 if something fails. */ -static int bq27x00_battery_voltage (struct bq27x00_device_info *di) +static int bq27x00_battery_read_time (struct bq27x00_device_info *di,u8 reg) { -int ret; -int volt =0 ; +int tval; - ret =bq27x00_read (di, BQ27x00_REG_VOLT, &volt, false); -if (ret) { -dev_err (di->dev,"error reading voltage\n" ); -return ret; + tval =bq27x00_read (di, reg, false); +if (tval <0 ) { +dev_err (di->dev,"error reading register %02x: %d\n" , reg, tval); +return tval; } -return volt *1000 ; +if (tval ==65535 ) +return -ENODATA ; + +return tval *60 ; +} + +static void bq27x00_update (struct bq27x00_device_info *di) +{ +struct bq27x00_reg_cache cache = {0 , }; +bool is_bq27500 = di->chip ==BQ27500 ; + + cache.voltage =bq27x00_battery_read_voltage (di); +if (cache.voltage >=0 ) { + cache.flags =bq27x00_read (di, BQ27x00_REG_FLAGS, is_bq27500); + cache.current_now =bq27x00_read (di, BQ27x00_REG_AI, false); + cache.capacity =bq27x00_battery_read_rsoc (di); + cache.temperature =bq27x00_read (di, BQ27x00_REG_TEMP, false); + cache.time_to_empty =bq27x00_battery_read_time (di, BQ27x00_REG_TTE); + cache.time_to_empty_avg =bq27x00_battery_read_time (di, BQ27x00_REG_TTECP); + cache.time_to_full =bq27x00_battery_read_time (di, BQ27x00_REG_TTF); + } + +/* Ignore those values which are snapshots of the current battery state +* and are likely to be different even between two consecutive reads */ +if (memcmp (&di->cache, &cache,sizeof (cache) -2 *sizeof (int )) !=0 ) { + di->cache = cache; +power_supply_changed (&di->bat); + } + + di->last_update = jiffies; +} + +/* +* Return the battery temperature in tenths of degree Celsius +* Or < 0 if something fails. +*/ +static int bq27x00_battery_temperature (struct bq27x00_device_info *di, +union power_supply_propval *val) +{ +if (di->cache.temperature <0 ) +return di->cache.temperature; + +if (di->chip ==BQ27500 ) + val->intval = di->cache.temperature -2731 ; +else + val->intval = ((di->cache.temperature *5 ) -5463 ) /2 ; + +return 0 ; }/*
@@ -134,109 +206,68 @@ static int bq27x00_battery_voltage(struct bq27x00_device_info *di)* Note that current can be negative signed as well * Or 0 if something fails. */ -static int bq27x00_battery_current (struct bq27x00_device_info *di) +static int bq27x00_battery_current (struct bq27x00_device_info *di, +union power_supply_propval *val) { -int ret;int curr =0 ; -int flags =0 ; - ret =bq27x00_read (di, BQ27x00_REG_AI, &curr, false); -if (ret) { -dev_err (di->dev,"error reading current\n" ); -return 0 ; - } +if (di->cache.current_now <0 ) +return di->cache.current_now;if (di->chip ==BQ27500 ) {/* bq27500 returns signed value */ - curr = (int )((s16 )curr) *1000 ; + val->intval = (int )((s16 )di->cache.current_now) *1000 ; }else { - ret =bq27x00_read (di, BQ27x00_REG_FLAGS, &flags, false); -if (ret <0 ) { -dev_err (di->dev,"error reading flags\n" ); -return 0 ; - } -if (flags &BQ27000_FLAG_CHGS ) { +if (di->cache.flags <0 ) +return di->cache.flags; + + curr = di->cache.current_now; +if (di->cache.flags &BQ27000_FLAG_CHGS ) {dev_dbg (di->dev,"negative current!\n" ); curr = -curr; } - curr = curr *3570 /BQ27000_RS ; - } - -return curr; -} -/* -* Return the battery Relative State-of-Charge -* Or < 0 if something fails. -*/ -static int bq27x00_battery_rsoc (struct bq27x00_device_info *di) -{ -int ret; -int rsoc =0 ; - -if (di->chip ==BQ27500 ) - ret =bq27x00_read (di,BQ27500_REG_SOC , &rsoc, false); -else - ret =bq27x00_read (di,BQ27000_REG_RSOC , &rsoc, true); -if (ret) { -dev_err (di->dev,"error reading relative State-of-Charge\n" ); -return ret; + val->intval = curr *3570 /BQ27000_RS ; } -return rsoc; +return 0 ; }static int bq27x00_battery_status (struct bq27x00_device_info *di, -union power_supply_propval *val) +union power_supply_propval *val) { -int flags =0 ;int status; -int ret; - ret =bq27x00_read (di, BQ27x00_REG_FLAGS, &flags, false); -if (ret <0 ) { -dev_err (di->dev,"error reading flags\n" ); -return ret; - } +if (di->cache.flags <0 ) +return di->cache.flags;if (di->chip ==BQ27500 ) { -if (flags &BQ27500_FLAG_FC ) +if (di->cache.flags &BQ27500_FLAG_FC ) status =POWER_SUPPLY_STATUS_FULL ; -else if (flags &BQ27500_FLAG_DSC ) +else if (di->cache.flags &BQ27500_FLAG_DSC ) status =POWER_SUPPLY_STATUS_DISCHARGING ;else status =POWER_SUPPLY_STATUS_CHARGING ; }else { -if (flags &BQ27000_FLAG_CHGS ) +if (di->cache.flags &BQ27000_FLAG_CHGS ) status =POWER_SUPPLY_STATUS_CHARGING ;else status =POWER_SUPPLY_STATUS_DISCHARGING ; } val->intval = status; +return 0 ; } -/* -* Read a time register. -* Return < 0 if something fails. -*/ -static int bq27x00_battery_time (struct bq27x00_device_info *di,int reg, -union power_supply_propval *val) +static int bq27x00_simple_value (int value, +union power_supply_propval *val) { -int tval =0 ; -int ret; - - ret =bq27x00_read (reg, &tval, false); -if (ret) { -dev_err (di->dev,"error reading register %02x\n" , reg); -return ret; - } +if (value <0 ) +return value; -if (tval ==65535 ) -return -ENODATA ; + val->intval = value; - val->intval = tval *60 ;return 0 ; }
@@ -249,9 +280,11 @@ static int bq27x00_battery_get_property(struct power_supply *psy, {int ret =0 ;struct bq27x00_device_info *di =to_bq27x00_device_info (psy); -int voltage =bq27x00_battery_voltage (di); -if (psp !=POWER_SUPPLY_PROP_PRESENT && voltage <=0 ) +if (time_is_before_jiffies (di->last_update +6 *HZ )) +bq27x00_update (di); + +if (psp !=POWER_SUPPLY_PROP_PRESENT && di->cache.voltage <=0 )return -ENODEV ;switch (psp) {
@@ -259,29 +292,28 @@ static int bq27x00_battery_get_property(struct power_supply *psy, ret =bq27x00_battery_status (di, val);break ;case POWER_SUPPLY_PROP_VOLTAGE_NOW : - val->intval = voltage; + ret =bq27x00_simple_value (di->cache.voltage, val);break ;case POWER_SUPPLY_PROP_PRESENT : -if (psp ==POWER_SUPPLY_PROP_PRESENT ) - val->intval = voltage <=0 ?0 :1 ; + val->intval = di->cache.voltage <=0 ?0 :1 ;break ;case POWER_SUPPLY_PROP_CURRENT_NOW : - val->intval =bq27x00_battery_current (di); + ret =bq27x00_battery_current (di, val);break ;case POWER_SUPPLY_PROP_CAPACITY : - val->intval =bq27x00_battery_rsoc (di); + ret =bq27x00_simple_value (di->cache.capacity, val);break ;case POWER_SUPPLY_PROP_TEMP : - val->intval =bq27x00_battery_temperature (di); + ret =bq27x00_battery_temperature (di, val);break ;case POWER_SUPPLY_PROP_TIME_TO_EMPTY_NOW : - ret =bq27x00_battery_time (di, BQ27x00_REG_TTE, val); + ret =bq27x00_simple_value (di->cache.time_to_empty, val);break ;case POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG : - ret =bq27x00_battery_time (di, BQ27x00_REG_TTECP, val); + ret =bq27x00_simple_value (di->cache.time_to_empty_avg, val);break ;case POWER_SUPPLY_PROP_TIME_TO_FULL_NOW : - ret =bq27x00_battery_time (di, BQ27x00_REG_TTF, val); + ret =bq27x00_simple_value (di->cache.time_to_full, val);break ;case POWER_SUPPLY_PROP_TECHNOLOGY : val->intval =POWER_SUPPLY_TECHNOLOGY_LION ;
@@ -311,6 +343,8 @@ static int bq27x00_powersupply_init(struct bq27x00_device_info *di)dev_info (di->dev,"support ver. %s enabled\n" ,DRIVER_VERSION ); +bq27x00_update (di); +return 0 ; }
@@ -324,13 +358,12 @@ static int bq27x00_powersupply_init(struct bq27x00_device_info *di)static DEFINE_IDR (battery_id);static DEFINE_MUTEX (battery_mutex); -static int bq27x00_read_i2c (struct bq27x00_device_info *di,u8 reg, -int *rt_value,bool single) +static int bq27x00_read_i2c (struct bq27x00_device_info *di,u8 reg,bool single) {struct i2c_client *client =to_i2c_client (di->dev);struct i2c_msg msg[1 ];unsigned char data[2 ]; -int err; +int err, ret;if (!client->adapter)return -ENODEV ;
@@ -353,14 +386,12 @@ static int bq27x00_read_i2c(struct bq27x00_device_info *di, u8 reg, err =i2c_transfer (client->adapter, msg,1 );if (err >=0 ) {if (!single) - *rt_value =get_unaligned_le16 (data); + ret =get_unaligned_le16 (data);else - *rt_value = data[0 ]; - -return 0 ; + ret = data[0 ]; } } -return err; +return ret; } static int bq27x00_battery_probe(struct i2c_client *client,
@@ -477,7 +508,7 @@ static inline void bq27x00_battery_i2c_exit(void) {};#ifdef CONFIG_BATTERY_BQ27X00_PLATFORM static int bq27000_read_platform (struct bq27x00_device_info *di,u8 reg, -int *rt_value,bool single) +bool single) {struct device *dev = di->dev;struct bq27000_platform_data *pdata = dev->platform_data;
@@ -504,14 +535,10 @@ static int bq27000_read_platform(struct bq27x00_device_info *di, u8 reg,if (timeout ==0 )return -EIO ; - *rt_value = (upper <<8 ) | lower; - }else { - lower = pdata->read (dev, reg); -if (lower <0 ) -return lower; - *rt_value = lower; +return (upper <<8 ) | lower; } -return 0 ; + +return pdata->read (dev, reg); }static int __devinit bq27000_battery_probe (struct platform_device *pdev)
Signature · 1 line
1.7.2.3
PATCH 8/14 POWER: bq27x00: Poll battery state
In reply to Lars-Peter ClausenThis patch adds support for polling the battery state and generating a power_supply_changed() event if it has changed.
--- drivers/power/bq27x00_battery.c | 47 +++++++++++++++++++++++++++++++++++--- 1 files changed, 43 insertions(+), 4 deletions(-)
drivers/power/bq27x00_battery.c +43 -4
@@ -19,6 +19,7 @@#include <linux/module.h> #include <linux/param.h> #include <linux/jiffies.h> +#include <linux/workqueue.h> #include <linux/delay.h> #include <linux/platform_device.h> #include <linux/power_supply.h>
@@ -74,6 +75,7 @@ struct bq27x00_device_info {struct bq27x00_reg_cache cache;unsigned long last_update; +struct delayed_work work;struct power_supply bat;
@@ -93,6 +95,11 @@ static enum power_supply_property bq27x00_battery_props[] = { POWER_SUPPLY_PROP_TECHNOLOGY, }; +static unsigned int poll_interval =360 ; +module_param (poll_interval, uint,0644 ); +MODULE_PARM_DESC (poll_interval,"battery poll interval in seconds - " \ +"0 disables polling" ); +/* * Common code for BQ27x00 devices */
@@ -282,7 +289,7 @@ static int bq27x00_battery_get_property(struct power_supply *psy,struct bq27x00_device_info *di =to_bq27x00_device_info (psy);if (time_is_before_jiffies (di->last_update +6 *HZ )) -bq27x00_update (di); +flush_delayed_work_sync (&di->work);if (psp !=POWER_SUPPLY_PROP_PRESENT && di->cache.voltage <=0 )return -ENODEV ;
@@ -325,6 +332,28 @@ static int bq27x00_battery_get_property(struct power_supply *psy,return ret; } +static void bq27x00_battery_work (struct work_struct *work) +{ +struct bq27x00_device_info *di = + container_of(work, struct bq27x00_device_info, work.work); + +bq27x00_update (di); + +if (poll_interval >0 ) { +/* The timer does not have to be accurate. */ +set_timer_slack (&di->work.timer, poll_interval *HZ /4 ); +schedule_delayed_work (&di->work, poll_interval *HZ ); + } +} + +static void bq27x00_external_power_changed (struct power_supply *psy) +{ +struct bq27x00_device_info *di =to_bq27x00_device_info (psy); + +cancel_delayed_work_sync (&di->work); +schedule_delayed_work (&di->work,0 ); +} +static int bq27x00_powersupply_init (struct bq27x00_device_info *di) {int ret;
@@ -333,7 +362,9 @@ static int bq27x00_powersupply_init(struct bq27x00_device_info *di) di->bat.properties = bq27x00_battery_props; di->bat.num_properties =ARRAY_SIZE (bq27x00_battery_props); di->bat.get_property = bq27x00_battery_get_property; - di->bat.external_power_changed =NULL ; + di->bat.external_power_changed = bq27x00_external_power_changed; + +INIT_DELAYED_WORK (&di->work, bq27x00_battery_work); ret =power_supply_register (di->dev, &di->bat);if (ret) {
@@ -348,6 +379,13 @@ static int bq27x00_powersupply_init(struct bq27x00_device_info *di)return 0 ; } +static void bq27x00_powersupply_unregister (struct bq27x00_device_info *di) +{ +cancel_delayed_work_sync (&di->work); + +power_supply_unregister (&di->bat); +} +/* i2c specific code */ #ifdef CONFIG_BATTERY_BQ27X00_I2C
@@ -455,7 +493,7 @@ static int bq27x00_battery_remove(struct i2c_client *client) {struct bq27x00_device_info *di =i2c_get_clientdata (client); -power_supply_unregister (&di->bat); +bq27x00_powersupply_unregister (di);kfree (di->bat.name);
@@ -588,7 +626,8 @@ static int __devexit bq27000_battery_remove(struct platform_device *pdev) {struct bq27x00_device_info *di =platform_get_drvdata (pdev); -power_supply_unregister (&di->bat); +bq27x00_powersupply_unregister (di); +platform_set_drvdata (pdev,NULL );kfree (di);
Signature · 1 line
1.7.2.3
PATCH 9/14 POWER: bq27x00: Add new properties
In reply to Lars-Peter ClausenFrom: Pali Rohár <[email protected]>
This patch add support for reporting properties POWER_SUPPLY_PROP_CHARGE_NOW, POWER_SUPPLY_PROP_CHARGE_FULL, POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN, POWER_SUPPLY_PROP_CHARGE_COUNTER, POWER_SUPPLY_PROP_ENERGY_NOW in module bq27x00_battery.
--- drivers/power/bq27x00_battery.c | 158 ++++++++++++++++++++++++++++++++++++++- 1 files changed, 156 insertions(+), 2 deletions(-)
drivers/power/bq27x00_battery.c +156 -2
@@ -16,6 +16,13 @@* WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. * */ + +/* +* Datasheets: +* http://focus.ti.com/docs/prod/folders/print/bq27000.html +* http://focus.ti.com/docs/prod/folders/print/bq27500.html +*/ +#include <linux/module.h> #include <linux/param.h> #include <linux/jiffies.h>
@@ -30,7 +37,7 @@#include <linux/power/bq27x00_battery.h> -#define DRIVER_VERSION "1.1.0" +#define DRIVER_VERSION "1.2.0"#define BQ27x00_REG_TEMP 0x06#define BQ27x00_REG_VOLT 0x08
@@ -39,11 +46,17 @@#define BQ27x00_REG_TTE 0x16#define BQ27x00_REG_TTF 0x18#define BQ27x00_REG_TTECP 0x26 +#define BQ27x00_REG_NAC 0x0C/* Nominal available capaciy */ +#define BQ27x00_REG_LMD 0x12/* Last measured discharge */ +#define BQ27x00_REG_CYCT 0x2A/* Cycle count total */ +#define BQ27x00_REG_AE 0x22/* Available enery */ #define BQ27000_REG_RSOC 0x0B/* Relative State-of-Charge */ +#define BQ27000_REG_ILMD 0x76/* Initial last measured discharge */ #define BQ27000_FLAG_CHGS BIT(7)#define BQ27500_REG_SOC 0x2c +#define BQ27500_REG_DCAP 0x3C/* Design capacity */ #define BQ27500_FLAG_DSC BIT(0)#define BQ27500_FLAG_FC BIT(9)
@@ -61,11 +74,15 @@ struct bq27x00_reg_cache {int time_to_empty;int time_to_empty_avg;int time_to_full; +int charge_full; +int charge_counter;int capacity;int flags;int voltage; +int charge_now;int current_now; +int energy_now; };struct bq27x00_device_info {
@@ -74,6 +91,8 @@ struct bq27x00_device_info {enum bq27x00_chip chip;struct bq27x00_reg_cache cache; +int charge_design_full; +unsigned long last_update;struct delayed_work work;
@@ -93,6 +112,11 @@ static enum power_supply_property bq27x00_battery_props[] = {POWER_SUPPLY_PROP_TIME_TO_EMPTY_AVG ,POWER_SUPPLY_PROP_TIME_TO_FULL_NOW ,POWER_SUPPLY_PROP_TECHNOLOGY , +POWER_SUPPLY_PROP_CHARGE_FULL , +POWER_SUPPLY_PROP_CHARGE_NOW , +POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN , +POWER_SUPPLY_PROP_CHARGE_COUNTER , + POWER_SUPPLY_PROP_ENERGY_NOW, };static unsigned int poll_interval =360 ;
@@ -145,6 +169,113 @@ static int bq27x00_battery_read_rsoc(struct bq27x00_device_info *di) }/* +* Return the battery Nominal available capaciy in µAh +* Or < 0 if something fails. +*/ +static int bq27x00_battery_read_nac (struct bq27x00_device_info *di) +{ +int nac; + + nac =bq27x00_read (di, BQ27x00_REG_NAC, false); +if (nac <0 ) { +dev_err (di->dev,"error reading nominal available capacity\n" ); +return nac; + } + +if (di->chip ==BQ27500 ) + nac *=1000 ; +else + nac = nac *3570 /BQ27000_RS ; + +return nac; +} + +/* +* Return the battery Last measured discharge in µAh +* Or < 0 if something fails. +*/ +static int bq27x00_battery_read_lmd (struct bq27x00_device_info *di) +{ +int lmd; + + lmd =bq27x00_read (di, BQ27x00_REG_LMD, false); +if (lmd <0 ) { +dev_err (di->dev,"error reading last measured discharge\n" ); +return lmd; + } + +if (di->chip ==BQ27500 ) + lmd *=1000 ; +else + lmd = lmd *3570 /BQ27000_RS ; + +return lmd; +} + +/* +* Return the battery Initial last measured discharge in µAh +* Or < 0 if something fails. +*/ +static int bq27x00_battery_read_ilmd (struct bq27x00_device_info *di) +{ +int ilmd; + +if (di->chip ==BQ27500 ) + ilmd =bq27x00_read (di,BQ27500_REG_DCAP , false); +else + ilmd =bq27x00_read (di,BQ27000_REG_ILMD , true); + +if (ilmd <0 ) { +dev_err (di->dev,"error reading initial last measured discharge\n" ); +return ilmd; + } + +if (di->chip ==BQ27500 ) + ilmd *=1000 ; +else + ilmd = ilmd *256 *3570 /BQ27000_RS ; + +return ilmd; +} + +/* +* Return the battery Cycle count total +* Or < 0 if something fails. +*/ +static int bq27x00_battery_read_cyct (struct bq27x00_device_info *di) +{ +int cyct; + + cyct =bq27x00_read (di, BQ27x00_REG_CYCT, false); +if (cyct <0 ) +dev_err (di->dev,"error reading cycle count total\n" ); + +return cyct; +} + +/* +* Return the battery Available energy in µWh +* Or < 0 if something fails. +*/ +static int bq27x00_battery_read_energy (struct bq27x00_device_info *di) +{ +int ae; + + ae =bq27x00_read (di, BQ27x00_REG_AE, false); +if (ae <0 ) { +dev_err (di->dev,"error reading available energy\n" ); +return ae; + } + +if (di->chip ==BQ27500 ) + ae *=1000 ; +else + ae = ae *29200 /BQ27000_RS ; + +return ae; +} + +/* * Read a time register. * Return < 0 if something fails. */
@@ -178,11 +309,19 @@ static void bq27x00_update(struct bq27x00_device_info *di) cache.time_to_empty =bq27x00_battery_read_time (di, BQ27x00_REG_TTE); cache.time_to_empty_avg =bq27x00_battery_read_time (di, BQ27x00_REG_TTECP); cache.time_to_full =bq27x00_battery_read_time (di, BQ27x00_REG_TTF); + cache.charge_now =bq27x00_battery_read_nac (di); + cache.charge_full =bq27x00_battery_read_lmd (di); + cache.charge_counter =bq27x00_battery_read_cyct (di); + cache.energy_now =bq27x00_battery_read_energy (di); + +/* We only have to read charge design full once */ +if (di->charge_design_full <=0 ) + di->charge_design_full =bq27x00_battery_read_ilmd (di); }/* Ignore those values which are snapshots of the current battery state * and are likely to be different even between two consecutive reads */ -if (memcmp (&di->cache, &cache,sizeof (cache) -2 *sizeof (int )) !=0 ) { +if (memcmp (&di->cache, &cache,sizeof (cache) -4 *sizeof (int )) !=0 ) { di->cache = cache;power_supply_changed (&di->bat); }
@@ -325,6 +464,21 @@ static int bq27x00_battery_get_property(struct power_supply *psy,case POWER_SUPPLY_PROP_TECHNOLOGY : val->intval =POWER_SUPPLY_TECHNOLOGY_LION ;break ; +case POWER_SUPPLY_PROP_CHARGE_NOW : + ret =bq27x00_simple_value (di->cache.charge_now, val); +break ; +case POWER_SUPPLY_PROP_CHARGE_FULL : + ret =bq27x00_simple_value (di->cache.charge_full, val); +break ; +case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN : + ret =bq27x00_simple_value (di->charge_design_full, val); +break ; +case POWER_SUPPLY_PROP_CHARGE_COUNTER : + ret =bq27x00_simple_value (di->cache.charge_counter, val); +break ; +case POWER_SUPPLY_PROP_ENERGY_NOW : + ret =bq27x00_simple_value (di->cache.energy_now, val); +break ;default :return -EINVAL ; }
Signature · 1 line
1.7.2.3
PATCH 10/14 POWER: bq27x00: Add MODULE_DEVICE_TABLE
In reply to Lars-Peter ClausenFrom: Pali Rohár <[email protected]>
This patch adds MODULE_DEVICE_TABLE for module bq27x00_battery.
--- drivers/power/bq27x00_battery.c | 1 + 1 files changed, 1 insertions(+), 0 deletions(-)
drivers/power/bq27x00_battery.c +1 -0
@@ -665,6 +665,7 @@ static const struct i2c_device_id bq27x00_id[] = { { "bq27500", BQ27500 }, {}, }; +MODULE_DEVICE_TABLE(i2c, bq27x00_id); static struct i2c_driver bq27x00_battery_driver = { .driver = {
Signature · 1 line
1.7.2.3
Re: [PATCH 10/14] POWER: bq27x00: Add MODULE_DEVICE_TABLE
Quoted 26 lines · Lars-Peter Clausen
From: Pali Rohár <[email protected]>
This patch adds
MODULE_DEVICE_TABLEfor modulebq27x00_battery.Signed-off-by Pali Rohár <[email protected]>Tested-by Pali Rohár <[email protected]>Signed-off-by Lars-Peter Clausen <[email protected]>--- drivers/power/bq27x00_battery.c | 1 + 1 files changed, 1 insertions(+), 0 deletions(-)drivers/power/bq27x00_battery.c +1
-0@@ -665,6 +665,7 @@ static const struct i2c_device_id bq27x00_id[] = { { "bq27500", BQ27500 }, {}, }; +MODULE_DEVICE_TABLE(i2c, bq27x00_id); static struct i2c_driver bq27x00_battery_driver = { .driver = {Signature · 1 line
1.7.2.3
Signature · 5 lines
GNU/Linux Solutions e-mail: [email protected] Linux Device Driver [email protected] Embedded Systems phone: +39 349 2432127 UNIX programming skype: rodolfo.giometti Freelance ICT Italia - Consulente ICT Italia - www.consulenti-ict.it
PATCH 11/14 POWER: bq27x00: Give more specific reports on battery status
In reply to Lars-Peter ClausenThe current code only reports whether the battery is charging or discharging. But the battery also reports whether it is fully charged, furthermore by look at if the battery is supplied we can tell whether it is discharging or not charging.
--- drivers/power/bq27x00_battery.c | 7 ++++++- 1 files changed, 6 insertions(+), 1 deletions(-)
drivers/power/bq27x00_battery.c +6 -1
@@ -54,6 +54,7 @@#define BQ27000_REG_RSOC 0x0B/* Relative State-of-Charge */ #define BQ27000_REG_ILMD 0x76/* Initial last measured discharge */ #define BQ27000_FLAG_CHGS BIT(7) +#define BQ27000_FLAG_FC BIT(5)#define BQ27500_REG_SOC 0x2c#define BQ27500_REG_DCAP 0x3C/* Design capacity */
@@ -395,8 +396,12 @@ static int bq27x00_battery_status(struct bq27x00_device_info *di,else status =POWER_SUPPLY_STATUS_CHARGING ; }else { -if (di->cache.flags &BQ27000_FLAG_CHGS ) +if (di->cache.flags &BQ27000_FLAG_FC ) + status =POWER_SUPPLY_STATUS_FULL ; +else if (di->cache.flags &BQ27000_FLAG_CHGS ) status =POWER_SUPPLY_STATUS_CHARGING ; +else if (power_supply_am_i_supplied (&di->bat)) + status =POWER_SUPPLY_STATUS_NOT_CHARGING ;else status =POWER_SUPPLY_STATUS_DISCHARGING ; }
Signature · 1 line
1.7.2.3
Re: [PATCH 11/14] POWER: bq27x00: Give more specific reports on battery status
Quoted 39 lines · Lars-Peter Clausen
The current code only reports whether the battery is charging or discharging. But the battery also reports whether it is fully charged, furthermore by look at if the battery is supplied we can tell whether it is discharging or not charging.
Signed-off-by Lars-Peter Clausen <[email protected]>--- drivers/power/bq27x00_battery.c | 7 ++++++- 1 files changed, 6 insertions(+), 1 deletions(-)drivers/power/bq27x00_battery.c +6
-1@@ -54,6 +54,7 @@#define BQ27000_REG_RSOC 0x0B/* Relative State-of-Charge */ #define BQ27000_REG_ILMD 0x76/* Initial last measured discharge */ #define BQ27000_FLAG_CHGS BIT(7) +#define BQ27000_FLAG_FC BIT(5)#define BQ27500_REG_SOC 0x2c#define BQ27500_REG_DCAP 0x3C/* Design capacity */ @@ -395,8 +396,12 @@ static int bq27x00_battery_status(struct bq27x00_device_info *di,else status =POWER_SUPPLY_STATUS_CHARGING ; }else { -if (di->cache.flags &BQ27000_FLAG_CHGS ) +if (di->cache.flags &BQ27000_FLAG_FC ) + status =POWER_SUPPLY_STATUS_FULL ; +else if (di->cache.flags &BQ27000_FLAG_CHGS ) status =POWER_SUPPLY_STATUS_CHARGING ; +else if (power_supply_am_i_supplied (&di->bat)) + status =POWER_SUPPLY_STATUS_NOT_CHARGING ;else status =POWER_SUPPLY_STATUS_DISCHARGING ; }Signature · 1 line
1.7.2.3
Signature · 5 lines
GNU/Linux Solutions e-mail: [email protected] Linux Device Driver [email protected] Embedded Systems phone: +39 349 2432127 UNIX programming skype: rodolfo.giometti Freelance ICT Italia - Consulente ICT Italia - www.consulenti-ict.it
PATCH 12/14 POWER: bq27x00: Minor cleanups
In reply to Lars-Peter ClausenFrom: Pali Rohár <[email protected]>
* Consistently use uppercase for hexadecimal values.
* Clarify/fix the unit of functions return value in its comment.
--- drivers/power/bq27x00_battery.c | 6 +++--- 1 files changed, 3 insertions(+), 3 deletions(-)
drivers/power/bq27x00_battery.c +3 -3
@@ -56,7 +56,7 @@#define BQ27000_FLAG_CHGS BIT(7)#define BQ27000_FLAG_FC BIT(5) -#define BQ27500_REG_SOC 0x2c +#define BQ27500_REG_SOC 0x2C#define BQ27500_REG_DCAP 0x3C/* Design capacity */ #define BQ27500_FLAG_DSC BIT(0)#define BQ27500_FLAG_FC BIT(9)
@@ -136,7 +136,7 @@ static inline int bq27x00_read(struct bq27x00_device_info *di, u8 reg, }/* -* Return the battery Voltage in milivolts +* Return the battery Voltage in µV * Or < 0 if something fails. */ static int bq27x00_battery_read_voltage (struct bq27x00_device_info *di)
@@ -349,7 +349,7 @@ static int bq27x00_battery_temperature(struct bq27x00_device_info *di, }/* -* Return the battery average current +* Return the battery average current in µA * Note that current can be negative signed as well * Or 0 if something fails. */
Signature · 1 line
1.7.2.3
PATCH 13/14 POWER: bq27x00: Cleanup bq27x00_i2c_read
In reply to Lars-Peter ClausenSome minor stylistic cleanups.
--- drivers/power/bq27x00_battery.c | 45 ++++++++++++++++++++------------------ 1 files changed, 24 insertions(+), 21 deletions(-)
drivers/power/bq27x00_battery.c +24 -21
@@ -558,36 +558,39 @@ static DEFINE_MUTEX(battery_mutex);static int bq27x00_read_i2c (struct bq27x00_device_info *di,u8 reg,bool single) {struct i2c_client *client =to_i2c_client (di->dev); -struct i2c_msg msg[1 ]; +struct i2c_msg msg;unsigned char data[2 ];int err, ret;if (!client->adapter)return -ENODEV ; - msg->addr = client->addr; - msg->flags =0 ; - msg->len =1 ; - msg->buf = data; + msg.addr = client->addr; + msg.flags =0 ; + msg.len =1 ; + msg.buf = data; data[0 ] = reg; - err =i2c_transfer (client->adapter, msg,1 ); + err =i2c_transfer (client->adapter, &msg,1 ); + +if (err <0 ) +return err; + +if (single) + msg.len =1 ; +else + msg.len =2 ; + + msg.flags =I2C_M_RD ; + err =i2c_transfer (client->adapter, &msg,1 ); +if (err <0 ) +return err; + +if (!single) + ret =get_unaligned_le16 (data); +else + ret = data[0 ]; -if (err >=0 ) { -if (!single) - msg->len =2 ; -else - msg->len =1 ; - - msg->flags =I2C_M_RD ; - err =i2c_transfer (client->adapter, msg,1 ); -if (err >=0 ) { -if (!single) - ret =get_unaligned_le16 (data); -else - ret = data[0 ]; - } - }return ret; }
Signature · 1 line
1.7.2.3
PATCH 14/14 POWER: Ignore -ENODATA errors when generating a uevent
In reply to Lars-Peter ClausenSometimes a driver can not report a meaningful value for a certain property and returns -ENODATA.
Currently when generating a uevent and a property return -ENODATA it is treated as an error an no uevent is generated at all. This is not an desirable behavior.
This patch adds a special case for -ENODATA and ignores properties which return this error code when generating the uevent.
--- drivers/power/power_supply_sysfs.c | 2 +- 1 files changed, 1 insertions(+), 1 deletions(-)
drivers/power/power_supply_sysfs.c +1 -1
@@ -270,7 +270,7 @@ int power_supply_uevent(struct device *dev, struct kobj_uevent_env *env) attr = &power_supply_attrs[psy->properties[j]]; ret =power_supply_show_property (dev, attr, prop_buf); -if (ret == -ENODEV ) { +if (ret == -ENODEV || ret == -ENODATA ) {/* When a battery is absent, we expect -ENODEV. Don't abort; send the uevent with at least the the PRESENT=0 property */ ret =0 ;
Signature · 1 line
1.7.2.3
Hi,
Quoted 16 lines · Lars-Peter Clausen
This patch series contains a few updates for the bq27x00 driver:
* Support for additional power supply properties
* Support for the bq27000 battery which is identical to the bq27200 but is connected through the HDQ bus.
* Adds a register cache to the driver and introduces polling the batteries state
* Minor improvements and cleanupsThe last patch in this series is not specific to the bq27x00 driver but is required for uevents to be generated properly for this driver. The patch makes properties which return
-ENODATAto be ignored when generating uevents. Previously in such a case uevent generation would have been aborted with an error. But since the bq27x00 return-ENODATAfor theTIME_TO_FULLproperty when the battery is not charging and for theTIME_TO_EMPTYproperty when the battery is not discharging and at least one of them is always true uevent generation would always fail.
Quoted 4 lines
This series has so far been tested with the bq27000 and the bq27200 battery, but not with the bq27500 battery, so it would be nice if somebody with a board containing such a battery could test the patches to make sure that there are no regressions.
This might be a bit off-topic, but I have tried to get the battery on the Nokia N900 working, and so far I'm only able to query the remaining capacity, but not really to enabling charging. This is very annoying, as I can only hack a certain amount of time, and then I have to reflash, reboot, and wait for the batter to charge with the official system (if there's enough power to flash).
Do you have any hints how to do that?
Signature · 1 line
Felipe Contreras
Quoted 24 lines · Felipe Contreras
Hi,
Quoted 16 lines · Lars-Peter Clausen
This patch series contains a few updates for the bq27x00 driver:
* Support for additional power supply properties
* Support for the bq27000 battery which is identical to the bq27200 but is connected through the HDQ bus.
* Adds a register cache to the driver and introduces polling the batteries state
* Minor improvements and cleanupsThe last patch in this series is not specific to the bq27x00 driver but is required for uevents to be generated properly for this driver. The patch makes properties which return
-ENODATAto be ignored when generating uevents. Previously in such a case uevent generation would have been aborted with an error. But since the bq27x00 return-ENODATAfor theTIME_TO_FULLproperty when the battery is not charging and for theTIME_TO_EMPTYproperty when the battery is not discharging and at least one of them is always true uevent generation would always fail.Quoted 4 lines
This series has so far been tested with the bq27000 and the bq27200 battery, but not with the bq27500 battery, so it would be nice if somebody with a board containing such a battery could test the patches to make sure that there are no regressions.
Quoted 9 lines
This might be a bit off-topic, but I have tried to get the battery on the Nokia N900 working, and so far I'm only able to query the remaining capacity, but not really to enabling charging. This is very annoying, as I can only hack a certain amount of time, and then I have to reflash, reboot, and wait for the batter to charge with the official system (if there's enough power to flash).
Do you have any hints how to do that?
Hi
Sorry, I've never worked with the N900, so I have no idea. But Pali has tested this patch series on his N900, so he might have an idea.
- Lars
Quoted 32 lines · Lars-Peter Clausen
Quoted 31 lines · Felipe Contreras
Hi,
Quoted 16 lines · Lars-Peter Clausen
This patch series contains a few updates for the bq27x00 driver:
* Support for additional power supply properties
* Support for the bq27000 battery which is identical to the bq27200 but is connected through the HDQ bus.
* Adds a register cache to the driver and introduces polling the batteries state
* Minor improvements and cleanupsThe last patch in this series is not specific to the bq27x00 driver but is required for uevents to be generated properly for this driver. The patch makes properties which return
-ENODATAto be ignored when generating uevents. Previously in such a case uevent generation would have been aborted with an error. But since the bq27x00 return-ENODATAfor theTIME_TO_FULLproperty when the battery is not charging and for theTIME_TO_EMPTYproperty when the battery is not discharging and at least one of them is always true uevent generation would always fail.Quoted 4 lines
This series has so far been tested with the bq27000 and the bq27200 battery, but not with the bq27500 battery, so it would be nice if somebody with a board containing such a battery could test the patches to make sure that there are no regressions.
This might be a bit off-topic, but I have tried to get the battery on the Nokia N900 working, and so far I'm only able to query the remaining capacity, but not really to enabling charging. This is very annoying, as I can only hack a certain amount of time, and then I have to reflash, reboot, and wait for the batter to charge with the official system (if there's enough power to flash).
Quoted 4 lines
Quoted 1 line
Do you have any hints how to do that?
Sorry, I've never worked with the N900, so I have no idea. But Pali has tested this patch series on his N900, so he might have an idea.
Well, it has a bq27200 AFAIK.
Signature · 1 line
Felipe Contreras
Quoted 33 lines · Felipe Contreras
Quoted 32 lines · Lars-Peter Clausen
Quoted 31 lines · Felipe Contreras
Hi,
Quoted 16 lines · Lars-Peter Clausen
This patch series contains a few updates for the bq27x00 driver:
* Support for additional power supply properties
* Support for the bq27000 battery which is identical to the bq27200 but is connected through the HDQ bus.
* Adds a register cache to the driver and introduces polling the batteries state
* Minor improvements and cleanupsThe last patch in this series is not specific to the bq27x00 driver but is required for uevents to be generated properly for this driver. The patch makes properties which return
-ENODATAto be ignored when generating uevents. Previously in such a case uevent generation would have been aborted with an error. But since the bq27x00 return-ENODATAfor theTIME_TO_FULLproperty when the battery is not charging and for theTIME_TO_EMPTYproperty when the battery is not discharging and at least one of them is always true uevent generation would always fail.Quoted 4 lines
This series has so far been tested with the bq27000 and the bq27200 battery, but not with the bq27500 battery, so it would be nice if somebody with a board containing such a battery could test the patches to make sure that there are no regressions.
This might be a bit off-topic, but I have tried to get the battery on the Nokia N900 working, and so far I'm only able to query the remaining capacity, but not really to enabling charging. This is very annoying, as I can only hack a certain amount of time, and then I have to reflash, reboot, and wait for the batter to charge with the official system (if there's enough power to flash).
Quoted 7 lines
Quoted 4 lines
Quoted 1 line
Do you have any hints how to do that?
Sorry, I've never worked with the N900, so I have no idea. But Pali has tested this patch series on his N900, so he might have an idea.
Well, it has a bq27200 AFAIK.
It has, but that doesn't tell you anything about the charging circuit.
- Lars
2011/2/7 Lars-Peter Clausen <[email protected]>:
Quoted 35 lines · Felipe Contreras
Quoted 24 lines
Hi,
Quoted 16 lines · Lars-Peter Clausen
This patch series contains a few updates for the bq27x00 driver:
* Support for additional power supply properties
* Support for the bq27000 battery which is identical to the bq27200 but is connected through the HDQ bus.
* Adds a register cache to the driver and introduces polling the batteries state
* Minor improvements and cleanupsThe last patch in this series is not specific to the bq27x00 driver but is required for uevents to be generated properly for this driver. The patch makes properties which return
-ENODATAto be ignored when generating uevents. Previously in such a case uevent generation would have been aborted with an error. But since the bq27x00 return-ENODATAfor theTIME_TO_FULLproperty when the battery is not charging and for theTIME_TO_EMPTYproperty when the battery is not discharging and at least one of them is always true uevent generation would always fail.Quoted 4 lines
This series has so far been tested with the bq27000 and the bq27200 battery, but not with the bq27500 battery, so it would be nice if somebody with a board containing such a battery could test the patches to make sure that there are no regressions.
Quoted 9 lines
This might be a bit off-topic, but I have tried to get the battery on the Nokia N900 working, and so far I'm only able to query the remaining capacity, but not really to enabling charging. This is very annoying, as I can only hack a certain amount of time, and then I have to reflash, reboot, and wait for the batter to charge with the official system (if there's enough power to flash).
Do you have any hints how to do that?
Quoted 7 lines
Hi
Sorry, I've never worked with the N900, so I have no idea. But Pali has tested this patch series on his N900, so he might have an idea.
- Lars
bq27x00 module does not support battery charging on Nokia N900. Only can report battery state and some properties.
Battery Managment Entity (BME) is proprietary Nokia software which can charge battery in Nokia N900. Alternative solution for charging battery you can find on: http://enivax.net/jk/n900/charge21.sh.txt
Signature · 2 lines
Pali Rohár [email protected]
Quoted 16 lines · Lars-Peter Clausen
This patch series contains a few updates for the bq27x00 driver:
* Support for additional power supply properties
* Support for the bq27000 battery which is identical to the bq27200 but is connected through the HDQ bus.
* Adds a register cache to the driver and introduces polling the batteries state
* Minor improvements and cleanupsThe last patch in this series is not specific to the bq27x00 driver but is required for uevents to be generated properly for this driver. The patch makes properties which return
-ENODATAto be ignored when generating uevents. Previously in such a case uevent generation would have been aborted with an error. But since the bq27x00 return-ENODATAfor theTIME_TO_FULLproperty when the battery is not charging and for theTIME_TO_EMPTYproperty when the battery is not discharging and at least one of them is always true uevent generation would always fail.
Quoted 4 lines
This series has so far been tested with the bq27000 and the bq27200 battery, but not with the bq27500 battery, so it would be nice if somebody with a board containing such a battery could test the patches to make sure that there are no regressions.
Trying this on pandora board (bq27500 over i2c) and it seems there is something wrong with the cache, I'm always getting the old values. I'm reading them manually over sysfs, uptime is over 25min but values still match ones on boot, even after turning off the backlight.
Looking at the code delayed_work handling looks suspicious, bq27x00_battery_get_property() flushes it and nothing ever reschedules it. Other than that all new property values looks sane.
Quoted 22 lines · Grazvydas Ignotas
Quoted 16 lines · Lars-Peter Clausen
This patch series contains a few updates for the bq27x00 driver:
* Support for additional power supply properties
* Support for the bq27000 battery which is identical to the bq27200 but is connected through the HDQ bus.
* Adds a register cache to the driver and introduces polling the batteries state
* Minor improvements and cleanupsThe last patch in this series is not specific to the bq27x00 driver but is required for uevents to be generated properly for this driver. The patch makes properties which return
-ENODATAto be ignored when generating uevents. Previously in such a case uevent generation would have been aborted with an error. But since the bq27x00 return-ENODATAfor theTIME_TO_FULLproperty when the battery is not charging and for theTIME_TO_EMPTYproperty when the battery is not discharging and at least one of them is always true uevent generation would always fail.Quoted 4 lines
This series has so far been tested with the bq27000 and the bq27200 battery, but not with the bq27500 battery, so it would be nice if somebody with a board containing such a battery could test the patches to make sure that there are no regressions.
Quoted 8 lines
Trying this on pandora board (bq27500 over i2c) and it seems there is something wrong with the cache, I'm always getting the old values. I'm reading them manually over sysfs, uptime is over 25min but values still match ones on boot, even after turning off the backlight.
Looking at the code
delayed_workhandling looks suspicious,bq27x00_battery_get_property()flushes it and nothing ever reschedules it. Other than that all new property values looks sane.
Hi
Hm, I tought that rescheduling from withing the work function would work, even when flushing the work, at least it did here.
But the current code is broken if poll_interval is 0 anyway, cause then it wont reschedule itself and is never run again.
Could you try:
if (time_is_before_jiffies(di->last_update + 6 * HZ)) {
cancel_delayed_work_sync(&di->work);
bq27x00_battery_work(&di->work);
}- Lars
Quoted 23 lines · Lars-Peter Clausen
Quoted 6 lines · Grazvydas Ignotas
Quoted 4 lines · Lars-Peter Clausen
This series has so far been tested with the bq27000 and the bq27200 battery, but not with the bq27500 battery, so it would be nice if somebody with a board containing such a battery could test the patches to make sure that there are no regressions.
Quoted 8 lines
Trying this on pandora board (bq27500 over i2c) and it seems there is something wrong with the cache, I'm always getting the old values. I'm reading them manually over sysfs, uptime is over 25min but values still match ones on boot, even after turning off the backlight.
Looking at the code
delayed_workhandling looks suspicious,bq27x00_battery_get_property()flushes it and nothing ever reschedules it. Other than that all new property values looks sane.Hi
Hm, I tought that rescheduling from withing the work function would work, even when flushing the work, at least it did here.
But the current code is broken ifpoll_intervalis 0 anyway, cause then it wont reschedule itself and is never run again.
Quoted 6 lines
Could you try:
if (
time_is_before_jiffies(di->last_update + 6 * HZ)) {cancel_delayed_work_sync(&di->work);bq27x00_battery_work(&di->work);
}
That works. However I wonder about the delay, I've experimentally determined that bq27500 refreshes in about a second, so before this series I could for example run 'watch -n 1 cat current_now' and see current changes almost in realtime (when toggling backlight, for example). Maybe we could have different cache timeout for different chips or have quickly changing properties (like current and voltage) bypass the cache.
Quoted 7 lines · Grazvydas Ignotas
That works. However I wonder about the delay, I've experimentally determined that bq27500 refreshes in about a second, so before this series I could for example run 'watch -n 1 cat
current_now' and see current changes almost in realtime (when toggling backlight, for example). Maybe we could have different cache timeout for different chips or have quickly changing properties (like current and voltage) bypass the cache.
Looking at the datasheet confirms that the bq27500 updates the current register every second. The bq27000 updates it only every 5.12 seconds.
I think reducing the the cache time for bq27500 to 1 second would render the cache mostly useless, but maybe it makes sense to bypass the cache for voltage and current on the bq27500.
- Lars
Quoted 9 lines · Lars-Peter Clausen
Quoted 7 lines · Grazvydas Ignotas
That works. However I wonder about the delay, I've experimentally determined that bq27500 refreshes in about a second, so before this series I could for example run 'watch -n 1 cat
current_now' and see current changes almost in realtime (when toggling backlight, for example). Maybe we could have different cache timeout for different chips or have quickly changing properties (like current and voltage) bypass the cache.
Quoted 5 lines
Looking at the datasheet confirms that the bq27500 updates the current register every second. The bq27000 updates it only every 5.12 seconds.
I think reducing the the cache time for bq27500 to 1 second would render the cache mostly useless, but maybe it makes sense to bypass the cache for voltage and current on the bq27500.
Nope, it's not useless. I.e. for cat /sys/class/power_supply/*/*. Actually, it was only the purpose for caching the battery values.
So, 1 second is OK.
p.s. Lars, on the next resend, can you please remove "POWER:" prefix from the patch description line, bound the commit message width to 76 symbols, and add all the collected Acked-by lines. That way I can just pull your tree.
Thanks!
Signature · 2 lines
Anton Vorontsov Email: [email protected]
Quoted 16 lines · Anton Vorontsov
Quoted 9 lines · Lars-Peter Clausen
Quoted 7 lines · Grazvydas Ignotas
That works. However I wonder about the delay, I've experimentally determined that bq27500 refreshes in about a second, so before this series I could for example run 'watch -n 1 cat
current_now' and see current changes almost in realtime (when toggling backlight, for example). Maybe we could have different cache timeout for different chips or have quickly changing properties (like current and voltage) bypass the cache.Quoted 5 lines
Looking at the datasheet confirms that the bq27500 updates the current register every second. The bq27000 updates it only every 5.12 seconds.
I think reducing the the cache time for bq27500 to 1 second would render the cache mostly useless, but maybe it makes sense to bypass the cache for voltage and current on the bq27500.
Quoted 4 lines
Nope, it's not useless. I.e. for
cat /sys/class/power_supply/*/*. Actually, it was only the purpose for caching the battery values.So, 1 second is OK.
Yes, the purpose of the register cache was that registers aren't read multiple times if multiple properties are queried at once. Which is what I consider the standard use case, since this is what a power monitor application would normally do.
The other use case is constantly monitor a single property like CURRENT_NOW. Since we would now read all properties instead of just one and would increase the load on the bus by 12 times.
The other purpose of the register cache was to be able to tell whether registers have changed when polling the battery. Since we already ignore the *_NOW properties when comparing the the old and the new state it would make sense to bypass the cache completely for them.
This would reduce the load when monitoring such a property and it would also reduce the load when polling the battery since we would only read 8 instead of 12 registers.
Quoted 5 lines
p.s. Lars, on the next resend, can you please remove "POWER:" prefix from the patch description line, bound the commit message width to 76 symbols, and add all the collected Acked-by lines. That way I can just pull your tree.
Sure.
- Lars