HWMON: DA9052 hwmon driver v2

new file mode 100755
index 0000000..0b7930f
@@ -0,0 +1,58 @@
+Kernel driver da9052-hwmon
+==========================
+
+Supported chips:
+  * Dialog Semiconductors DA9052 PMICs
+    Prefix: 'da9052'
+    Datasheet: Kindly visit www.dialog-semiconductor.com and request for the
+               official datasheet.
+
+Authors: David Dajun Chen <[email protected]>
+
+Description
+-----------
+
+The DA9052 provides an Analogue to Digital Converter (ADC) with 10 bits
+resolution and track and hold circuitry combined with an analogue input
+multiplexer. The analogue input multiplexer will allow conversion of up to 10
+different inputs. The track and hold circuit ensures stable input voltages at
+the input of the ADC during the conversion.
+
+The ADC is used to measure the following inputs:
+Channel 0: VDDOUT - measurement of the system voltage
+Channel 1: ICH - internal battery charger current measurement
+Channel 2: TBAT - output from the battery NTC
+Channel 3: VBAT - measurement of the battery voltage
+Channel 4: ADC_IN4 - high impedance input (0 - 2.5V)
+Channel 5: ADC_IN5 - high impedance input (0 - 2.5V)
+Channel 6: ADC_IN6 - high impedance input (0 - 2.5V)
+Channel 7: XY - TSI interface to measure the X and Y voltage of the touch
+screen resistive potentiometers
+Channel 8: Internal Tjunc. - sense (internal temp. sensor)
+Channel 9: VBBAT - measurement of the backup battery voltage
+
+By using sysfs attributes we can measure the system voltage VDDOUT, the battery
+charging current ICH, battery temperature TBAT, battery junction temperature
+TJUNC, battery voltage VBAT and the back up battery voltage VBBAT.
+
+Voltage Monitoring
+------------------
+
+Voltages are sampled by a 10 bit ADC.  Voltages in millivolts are 1.465
+times the ADC value.
+
+Temperature Monitoring
+----------------------
+
+Temperatures are sampled by a 10 bit ADC.  Junction and battery temperatures
+are monitored by the ADC channels.
+
+The junction temperature is calculated:
+	Degrees celsius = 1.708 * (TJUNC_RES - T_OFFSET) - 108.8
+The junction temperature attribute is supported by the driver.
+
+The battery temperature is calculated:
+	Degree Celcius = 1 / (t1 + 1/298)- 273
+where t1 = (1/B)* ln(( ADCval * 2.5)/(R25*ITBAT*255))
+Default values of R25, B, ITBAT are 10e3, 3380 and 50e-6 respectively.
+

index 3236a45..da5ff6d 100644
@@ -303,6 +303,16 @@ config SENSORS_DS1621
 	  This driver can also be built as a module.  If so, the module
 	  will be called ds1621.
 
+config SENSORS_DA9052_ADC
+        tristate "Dialog DA9052 HWMON"
+        depends on PMIC_DA9052
+        help
+          Say y here to support the ADC found on
+          Dialog Semiconductor DA9052 PMIC.
+
+          This driver can also be built as module. If so, the module
+          will be called da9052-hwmon.
+
 config SENSORS_I5K_AMB
 	tristate "FB-DIMM AMB temperature sensor on Intel 5000 series chipsets"
 	depends on PCI && EXPERIMENTAL

index f7c0c28..88b81ca 100644
@@ -42,6 +42,7 @@ obj-$(CONFIG_SENSORS_ASC7621)	+= asc7621.o
 obj-$(CONFIG_SENSORS_ATXP1)	+= atxp1.o
 obj-$(CONFIG_SENSORS_CORETEMP)	+= coretemp.o
 obj-$(CONFIG_SENSORS_PKGTEMP)	+= pkgtemp.o
+obj-$(CONFIG_SENSORS_DA9052_ADC)+= da9052-hwmon.o
 obj-$(CONFIG_SENSORS_DME1737)	+= dme1737.o
 obj-$(CONFIG_SENSORS_DS620)	+= ds620.o
 obj-$(CONFIG_SENSORS_DS1621)	+= ds1621.o