drm/i915: Enable digital port hotplug on PCH systems
Subsystems (2)
PATCH 1/1 drm/i915: Enable digital port hotplug on PCH systems
We were relying on the BIOS to set these bits, which doesn't always happen.
---
v2: set the hotplug bits in the irq post-install hook, just like we do for pre-PCH hardware.
drivers/gpu/drm/i915/i915_irq.c | 24 ++++++++++++++++++++++++ drivers/gpu/drm/i915/i915_reg.h | 5 ++++- 2 files changed, 28 insertions(+), 1 deletions(-)
drivers/gpu/drm/i915/i915_irq.c +24 -0
@@ -1777,6 +1777,26 @@ static void ironlake_irq_preinstall(struct drm_device *dev)POSTING_READ (SDEIER ); } +/* +* Enable digital hotplug on the PCH, and configure the DP short pulse +* duration to 2ms (which is the minimum in the Display Port spec) +* +* This register is the same on all known PCH chips. +*/ + +static void ironlake_enable_pch_hotplug (struct drm_device *dev) +{ +drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private; +u32 hotplug; + + hotplug =I915_READ (PCH_PORT_HOTPLUG ); + hotplug &= ~(PORTD_PULSE_DURATION_MASK |PORTC_PULSE_DURATION_MASK |PORTB_PULSE_DURATION_MASK ); + hotplug |=PORTD_HOTPLUG_ENABLE | PORTD_PULSE_DURATION_2ms; + hotplug |=PORTC_HOTPLUG_ENABLE | PORTC_PULSE_DURATION_2ms; + hotplug |=PORTB_HOTPLUG_ENABLE | PORTB_PULSE_DURATION_2ms; +I915_WRITE (PCH_PORT_HOTPLUG , hotplug); +} +static int ironlake_irq_postinstall (struct drm_device *dev) {drm_i915_private_t *dev_priv = (drm_i915_private_t *) dev->dev_private;
@@ -1839,6 +1859,8 @@ static int ironlake_irq_postinstall(struct drm_device *dev)I915_WRITE (SDEIER , hotplug_mask);POSTING_READ (SDEIER ); +ironlake_enable_pch_hotplug (dev); +if (IS_IRONLAKE_M (dev)) {/* Clear & enable PCU event interrupts */ I915_WRITE (DEIIR ,DE_PCU_EVENT );
@@ -1896,6 +1918,8 @@ static int ivybridge_irq_postinstall(struct drm_device *dev)I915_WRITE (SDEIER , hotplug_mask);POSTING_READ (SDEIER ); +ironlake_enable_pch_hotplug (dev); +return 0 ; }
drivers/gpu/drm/i915/i915_reg.h +4 -1
@@ -2903,12 +2903,13 @@#define SDEIER 0xc400c/* digital port hotplug */ -#define PCH_PORT_HOTPLUG 0xc4030 +#define PCH_PORT_HOTPLUG 0xc4030/* SHOTPLUG_CTL */ #define PORTD_HOTPLUG_ENABLE (1 << 20)#define PORTD_PULSE_DURATION_2ms (0)#define PORTD_PULSE_DURATION_4_5ms (1 << 18)#define PORTD_PULSE_DURATION_6ms (2 << 18)#define PORTD_PULSE_DURATION_100ms (3 << 18) +#define PORTD_PULSE_DURATION_MASK (3 << 18)#define PORTD_HOTPLUG_NO_DETECT (0)#define PORTD_HOTPLUG_SHORT_DETECT (1 << 16)#define PORTD_HOTPLUG_LONG_DETECT (1 << 17)
@@ -2917,6 +2918,7 @@#define PORTC_PULSE_DURATION_4_5ms (1 << 10)#define PORTC_PULSE_DURATION_6ms (2 << 10)#define PORTC_PULSE_DURATION_100ms (3 << 10) +#define PORTC_PULSE_DURATION_MASK (3 << 10)#define PORTC_HOTPLUG_NO_DETECT (0)#define PORTC_HOTPLUG_SHORT_DETECT (1 << 8)#define PORTC_HOTPLUG_LONG_DETECT (1 << 9)
@@ -2925,6 +2927,7 @@#define PORTB_PULSE_DURATION_4_5ms (1 << 2)#define PORTB_PULSE_DURATION_6ms (2 << 2)#define PORTB_PULSE_DURATION_100ms (3 << 2) +#define PORTB_PULSE_DURATION_MASK (3 << 2)#define PORTB_HOTPLUG_NO_DETECT (0)#define PORTB_HOTPLUG_SHORT_DETECT (1 << 0)#define PORTB_HOTPLUG_LONG_DETECT (1 << 1)
Signature · 1 line
1.7.6.3
Quoted 2 lines · Keith Packard
We were relying on the BIOS to set these bits, which doesn't always happen.
Do we need to clear IRQ bits on uninstall, for example to prevent "Interrupt 19: no one cared!" or is that due to a different cause?
More of a general question really. The patch itself looks good and matches against the spec afaics.
-Chris
Signature · 1 line
Chris Wilson, Intel Open Source Technology Centre
Quoted 6 lines · Chris Wilson
Quoted 2 lines · Keith Packard
We were relying on the BIOS to set these bits, which doesn't always happen.
Do we need to clear IRQ bits on uninstall, for example to prevent "Interrupt 19: no one cared!" or is that due to a different cause?
Probably a good plan, but of course that's separate from turning on the hotplug hardware in the PCH. Something like:
drivers/gpu/drm/i915/i915_irq.c +4 -0
@@ -2044,6 +2044,10 @@ static void ironlake_irq_uninstall(struct drm_device *dev)I915_WRITE (GTIMR ,0xffffffff );I915_WRITE (GTIER ,0x0 );I915_WRITE (GTIIR ,I915_READ (GTIIR )); + +I915_WRITE (SDEIMR ,0xffffffff ); +I915_WRITE (SDEIER ,0x0 ); +I915_WRITE (SDEIIR ,I915_READ (SDEIIR )); }static void i915_driver_irq_uninstall (struct drm_device * dev)
Quoted 2 lines
More of a general question really. The patch itself looks good and matches against the spec afaics.
I was amused to learn that the BIOS on my machine actually turns on the hotplug hardware for no good reason, so things 'worked' without this code on many machines. I wonder how many DP/DVI/HDMI machines aren't actually doing hotplug today...
Signature · 1 line
[email protected]